aboutsummaryrefslogtreecommitdiffstatshomepage
path: root/drivers/tty/serial/8250
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/tty/serial/8250')
-rw-r--r--drivers/tty/serial/8250/8250_dw.c2
-rw-r--r--drivers/tty/serial/8250/8250_fintek.c27
-rw-r--r--drivers/tty/serial/8250/8250_gsc.c2
-rw-r--r--drivers/tty/serial/8250/8250_mid.c19
-rw-r--r--drivers/tty/serial/8250/8250_mtk.c29
-rw-r--r--drivers/tty/serial/8250/8250_of.c11
-rw-r--r--drivers/tty/serial/8250/8250_omap.c5
-rw-r--r--drivers/tty/serial/8250/8250_pci.c203
-rw-r--r--drivers/tty/serial/8250/8250_port.c50
-rw-r--r--drivers/tty/serial/8250/serial_cs.c13
10 files changed, 273 insertions, 88 deletions
diff --git a/drivers/tty/serial/8250/8250_dw.c b/drivers/tty/serial/8250/8250_dw.c
index 51a7d3b19b39..381c5117aec1 100644
--- a/drivers/tty/serial/8250/8250_dw.c
+++ b/drivers/tty/serial/8250/8250_dw.c
@@ -660,7 +660,7 @@ static struct platform_driver dw8250_platform_driver = {
.name = "dw-apb-uart",
.pm = &dw8250_pm_ops,
.of_match_table = dw8250_of_match,
- .acpi_match_table = ACPI_PTR(dw8250_acpi_match),
+ .acpi_match_table = dw8250_acpi_match,
},
.probe = dw8250_probe,
.remove = dw8250_remove,
diff --git a/drivers/tty/serial/8250/8250_fintek.c b/drivers/tty/serial/8250/8250_fintek.c
index 31c91c2f8c6e..9b1cddbfc75c 100644
--- a/drivers/tty/serial/8250/8250_fintek.c
+++ b/drivers/tty/serial/8250/8250_fintek.c
@@ -197,12 +197,12 @@ static int fintek_8250_rs485_config(struct uart_port *port,
if (!pdata)
return -EINVAL;
- /* Hardware do not support same RTS level on send and receive */
- if (!(rs485->flags & SER_RS485_RTS_ON_SEND) ==
- !(rs485->flags & SER_RS485_RTS_AFTER_SEND))
- return -EINVAL;
if (rs485->flags & SER_RS485_ENABLED) {
+ /* Hardware do not support same RTS level on send and receive */
+ if (!(rs485->flags & SER_RS485_RTS_ON_SEND) ==
+ !(rs485->flags & SER_RS485_RTS_AFTER_SEND))
+ return -EINVAL;
memset(rs485->padding, 0, sizeof(rs485->padding));
config |= RS485_URA;
} else {
@@ -285,24 +285,6 @@ static void fintek_8250_set_max_fifo(struct fintek_8250 *pdata)
}
}
-static void fintek_8250_goto_highspeed(struct uart_8250_port *uart,
- struct fintek_8250 *pdata)
-{
- sio_write_reg(pdata, LDN, pdata->index);
-
- switch (pdata->pid) {
- case CHIP_ID_F81866: /* set uart clock for high speed serial mode */
- sio_write_mask_reg(pdata, F81866_UART_CLK,
- F81866_UART_CLK_MASK,
- F81866_UART_CLK_14_769MHZ);
-
- uart->port.uartclk = 921600 * 16;
- break;
- default: /* leave clock speed untouched */
- break;
- }
-}
-
static void fintek_8250_set_termios(struct uart_port *port,
struct ktermios *termios,
struct ktermios *old)
@@ -422,7 +404,6 @@ static int probe_setup_port(struct fintek_8250 *pdata,
fintek_8250_set_irq_mode(pdata, level_mode);
fintek_8250_set_max_fifo(pdata);
- fintek_8250_goto_highspeed(uart, pdata);
fintek_8250_exit_key(addr[i]);
diff --git a/drivers/tty/serial/8250/8250_gsc.c b/drivers/tty/serial/8250/8250_gsc.c
index 0809ae2aa9b1..51cc985216ff 100644
--- a/drivers/tty/serial/8250/8250_gsc.c
+++ b/drivers/tty/serial/8250/8250_gsc.c
@@ -26,7 +26,7 @@ static int __init serial_init_chip(struct parisc_device *dev)
unsigned long address;
int err;
-#ifdef CONFIG_64BIT
+#if defined(CONFIG_64BIT) && defined(CONFIG_IOSAPIC)
if (!dev->irq && (dev->id.sversion == 0xad))
dev->irq = iosapic_serial_irq(dev);
#endif
diff --git a/drivers/tty/serial/8250/8250_mid.c b/drivers/tty/serial/8250/8250_mid.c
index efa0515139f8..e6c1791609dd 100644
--- a/drivers/tty/serial/8250/8250_mid.c
+++ b/drivers/tty/serial/8250/8250_mid.c
@@ -73,6 +73,11 @@ static int pnw_setup(struct mid8250 *mid, struct uart_port *p)
return 0;
}
+static void pnw_exit(struct mid8250 *mid)
+{
+ pci_dev_put(mid->dma_dev);
+}
+
static int tng_handle_irq(struct uart_port *p)
{
struct mid8250 *mid = p->private_data;
@@ -124,6 +129,11 @@ static int tng_setup(struct mid8250 *mid, struct uart_port *p)
return 0;
}
+static void tng_exit(struct mid8250 *mid)
+{
+ pci_dev_put(mid->dma_dev);
+}
+
static int dnv_handle_irq(struct uart_port *p)
{
struct mid8250 *mid = p->private_data;
@@ -330,9 +340,9 @@ static int mid8250_probe(struct pci_dev *pdev, const struct pci_device_id *id)
pci_set_drvdata(pdev, mid);
return 0;
+
err:
- if (mid->board->exit)
- mid->board->exit(mid);
+ mid->board->exit(mid);
return ret;
}
@@ -342,8 +352,7 @@ static void mid8250_remove(struct pci_dev *pdev)
serial8250_unregister_port(mid->line);
- if (mid->board->exit)
- mid->board->exit(mid);
+ mid->board->exit(mid);
}
static const struct mid8250_board pnw_board = {
@@ -351,6 +360,7 @@ static const struct mid8250_board pnw_board = {
.freq = 50000000,
.base_baud = 115200,
.setup = pnw_setup,
+ .exit = pnw_exit,
};
static const struct mid8250_board tng_board = {
@@ -358,6 +368,7 @@ static const struct mid8250_board tng_board = {
.freq = 38400000,
.base_baud = 1843200,
.setup = tng_setup,
+ .exit = tng_exit,
};
static const struct mid8250_board dnv_board = {
diff --git a/drivers/tty/serial/8250/8250_mtk.c b/drivers/tty/serial/8250/8250_mtk.c
index 2b59a4305077..a79ab53f8e87 100644
--- a/drivers/tty/serial/8250/8250_mtk.c
+++ b/drivers/tty/serial/8250/8250_mtk.c
@@ -36,6 +36,7 @@
#define MTK_UART_IER_RTSI 0x40 /* Enable RTS Modem status interrupt */
#define MTK_UART_IER_CTSI 0x80 /* Enable CTS Modem status interrupt */
+#define MTK_UART_EFR 38 /* I/O: Extended Features Register */
#define MTK_UART_EFR_EN 0x10 /* Enable enhancement feature */
#define MTK_UART_EFR_RTS 0x40 /* Enable hardware rx flow control */
#define MTK_UART_EFR_CTS 0x80 /* Enable hardware tx flow control */
@@ -52,6 +53,9 @@
#define MTK_UART_TX_TRIGGER 1
#define MTK_UART_RX_TRIGGER MTK_UART_RX_SIZE
+#define MTK_UART_XON1 40 /* I/O: Xon character 1 */
+#define MTK_UART_XOFF1 42 /* I/O: Xoff character 1 */
+
#ifdef CONFIG_SERIAL_8250_DMA
enum dma_rx_status {
DMA_RX_START = 0,
@@ -92,10 +96,13 @@ static void mtk8250_dma_rx_complete(void *param)
struct dma_tx_state state;
int copied, total, cnt;
unsigned char *ptr;
+ unsigned long flags;
if (data->rx_status == DMA_RX_SHUTDOWN)
return;
+ spin_lock_irqsave(&up->port.lock, flags);
+
dmaengine_tx_status(dma->rxchan, dma->rx_cookie, &state);
total = dma->rx_size - state.residue;
cnt = total;
@@ -119,6 +126,8 @@ static void mtk8250_dma_rx_complete(void *param)
tty_flip_buffer_push(tty_port);
mtk8250_rx_dma(up);
+
+ spin_unlock_irqrestore(&up->port.lock, flags);
}
static void mtk8250_rx_dma(struct uart_8250_port *up)
@@ -163,7 +172,7 @@ static void mtk8250_dma_enable(struct uart_8250_port *up)
MTK_UART_DMA_EN_RX | MTK_UART_DMA_EN_TX);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
- serial_out(up, UART_EFR, UART_EFR_ECB);
+ serial_out(up, MTK_UART_EFR, UART_EFR_ECB);
serial_out(up, UART_LCR, lcr);
if (dmaengine_slave_config(dma->rxchan, &dma->rxconf) != 0)
@@ -226,7 +235,7 @@ static void mtk8250_set_flow_ctrl(struct uart_8250_port *up, int mode)
int lcr = serial_in(up, UART_LCR);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
- serial_out(up, UART_EFR, UART_EFR_ECB);
+ serial_out(up, MTK_UART_EFR, UART_EFR_ECB);
serial_out(up, UART_LCR, lcr);
lcr = serial_in(up, UART_LCR);
@@ -235,7 +244,7 @@ static void mtk8250_set_flow_ctrl(struct uart_8250_port *up, int mode)
serial_out(up, MTK_UART_ESCAPE_DAT, MTK_UART_ESCAPE_CHAR);
serial_out(up, MTK_UART_ESCAPE_EN, 0x00);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
- serial_out(up, UART_EFR, serial_in(up, UART_EFR) &
+ serial_out(up, MTK_UART_EFR, serial_in(up, MTK_UART_EFR) &
(~(MTK_UART_EFR_HW_FC | MTK_UART_EFR_SW_FC_MASK)));
serial_out(up, UART_LCR, lcr);
mtk8250_disable_intrs(up, MTK_UART_IER_XOFFI |
@@ -249,8 +258,8 @@ static void mtk8250_set_flow_ctrl(struct uart_8250_port *up, int mode)
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
/*enable hw flow control*/
- serial_out(up, UART_EFR, MTK_UART_EFR_HW_FC |
- (serial_in(up, UART_EFR) &
+ serial_out(up, MTK_UART_EFR, MTK_UART_EFR_HW_FC |
+ (serial_in(up, MTK_UART_EFR) &
(~(MTK_UART_EFR_HW_FC | MTK_UART_EFR_SW_FC_MASK))));
serial_out(up, UART_LCR, lcr);
@@ -264,12 +273,12 @@ static void mtk8250_set_flow_ctrl(struct uart_8250_port *up, int mode)
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
/*enable sw flow control */
- serial_out(up, UART_EFR, MTK_UART_EFR_XON1_XOFF1 |
- (serial_in(up, UART_EFR) &
+ serial_out(up, MTK_UART_EFR, MTK_UART_EFR_XON1_XOFF1 |
+ (serial_in(up, MTK_UART_EFR) &
(~(MTK_UART_EFR_HW_FC | MTK_UART_EFR_SW_FC_MASK))));
- serial_out(up, UART_XON1, START_CHAR(port->state->port.tty));
- serial_out(up, UART_XOFF1, STOP_CHAR(port->state->port.tty));
+ serial_out(up, MTK_UART_XON1, START_CHAR(port->state->port.tty));
+ serial_out(up, MTK_UART_XOFF1, STOP_CHAR(port->state->port.tty));
serial_out(up, UART_LCR, lcr);
mtk8250_disable_intrs(up, MTK_UART_IER_CTSI|MTK_UART_IER_RTSI);
mtk8250_enable_intrs(up, MTK_UART_IER_XOFFI);
@@ -316,7 +325,7 @@ mtk8250_set_termios(struct uart_port *port, struct ktermios *termios,
*/
baud = tty_termios_baud_rate(termios);
- serial8250_do_set_termios(port, termios, old);
+ serial8250_do_set_termios(port, termios, NULL);
tty_termios_encode_baud_rate(termios, baud, baud);
diff --git a/drivers/tty/serial/8250/8250_of.c b/drivers/tty/serial/8250/8250_of.c
index 9ba31701a372..a9b0a84b1e43 100644
--- a/drivers/tty/serial/8250/8250_of.c
+++ b/drivers/tty/serial/8250/8250_of.c
@@ -105,8 +105,17 @@ static int of_platform_serial_setup(struct platform_device *ofdev,
port->mapsize = resource_size(&resource);
/* Check for shifted address mapping */
- if (of_property_read_u32(np, "reg-offset", &prop) == 0)
+ if (of_property_read_u32(np, "reg-offset", &prop) == 0) {
+ if (prop >= port->mapsize) {
+ dev_warn(&ofdev->dev, "reg-offset %u exceeds region size %pa\n",
+ prop, &port->mapsize);
+ ret = -EINVAL;
+ goto err_unprepare;
+ }
+
port->mapbase += prop;
+ port->mapsize -= prop;
+ }
port->iotype = UPIO_MEM;
if (of_property_read_u32(np, "reg-io-width", &prop) == 0) {
diff --git a/drivers/tty/serial/8250/8250_omap.c b/drivers/tty/serial/8250/8250_omap.c
index f2c6d9d3bb28..efe793a2fc65 100644
--- a/drivers/tty/serial/8250/8250_omap.c
+++ b/drivers/tty/serial/8250/8250_omap.c
@@ -170,11 +170,6 @@ static void omap_8250_mdr1_errataset(struct uart_8250_port *up,
struct omap8250_priv *priv)
{
u8 timeout = 255;
- u8 old_mdr1;
-
- old_mdr1 = serial_in(up, UART_OMAP_MDR1);
- if (old_mdr1 == priv->mdr1)
- return;
serial_out(up, UART_OMAP_MDR1, priv->mdr1);
udelay(2);
diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c
index 8814ff38aa67..92e2ee278523 100644
--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
@@ -58,6 +58,8 @@ struct serial_private {
int line[0];
};
+#define PCI_DEVICE_ID_HPE_PCI_SERIAL 0x37e
+
static const struct pci_device_id pci_use_msi[] = {
{ PCI_DEVICE_SUB(PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9900,
0xA000, 0x1000) },
@@ -65,6 +67,8 @@ static const struct pci_device_id pci_use_msi[] = {
0xA000, 0x1000) },
{ PCI_DEVICE_SUB(PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9922,
0xA000, 0x1000) },
+ { PCI_DEVICE_SUB(PCI_VENDOR_ID_HP_3PAR, PCI_DEVICE_ID_HPE_PCI_SERIAL,
+ PCI_ANY_ID, PCI_ANY_ID) },
{ }
};
@@ -85,7 +89,7 @@ static void moan_device(const char *str, struct pci_dev *dev)
static int
setup_port(struct serial_private *priv, struct uart_8250_port *port,
- int bar, int offset, int regshift)
+ u8 bar, unsigned int offset, int regshift)
{
struct pci_dev *dev = priv->dev;
@@ -1347,29 +1351,33 @@ pericom_do_set_divisor(struct uart_port *port, unsigned int baud,
{
int scr;
int lcr;
- int actual_baud;
- int tolerance;
- for (scr = 5 ; scr <= 15 ; scr++) {
- actual_baud = 921600 * 16 / scr;
- tolerance = actual_baud / 50;
+ for (scr = 16; scr > 4; scr--) {
+ unsigned int maxrate = port->uartclk / scr;
+ unsigned int divisor = max(maxrate / baud, 1U);
+ int delta = maxrate / divisor - baud;
+
+ if (baud > maxrate + baud / 50)
+ continue;
- if ((baud < actual_baud + tolerance) &&
- (baud > actual_baud - tolerance)) {
+ if (delta > baud / 50)
+ divisor++;
+ if (divisor > 0xffff)
+ continue;
+
+ /* Update delta due to possible divisor change */
+ delta = maxrate / divisor - baud;
+ if (abs(delta) < baud / 50) {
lcr = serial_port_in(port, UART_LCR);
serial_port_out(port, UART_LCR, lcr | 0x80);
-
- serial_port_out(port, UART_DLL, 1);
- serial_port_out(port, UART_DLM, 0);
+ serial_port_out(port, UART_DLL, divisor & 0xff);
+ serial_port_out(port, UART_DLM, divisor >> 8 & 0xff);
serial_port_out(port, 2, 16 - scr);
serial_port_out(port, UART_LCR, lcr);
return;
- } else if (baud > actual_baud) {
- break;
}
}
- serial8250_do_set_divisor(port, baud, quot, quot_frac);
}
static int pci_pericom_setup(struct serial_private *priv,
const struct pciserial_board *board,
@@ -1966,6 +1974,16 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
.setup = pci_hp_diva_setup,
},
/*
+ * HPE PCI serial device
+ */
+ {
+ .vendor = PCI_VENDOR_ID_HP_3PAR,
+ .device = PCI_DEVICE_ID_HPE_PCI_SERIAL,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .setup = pci_hp_diva_setup,
+ },
+ /*
* Intel
*/
{
@@ -2271,7 +2289,7 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
.setup = pci_pericom_setup_four_at_eight,
},
{
- .vendor = PCI_DEVICE_ID_ACCESIO_PCIE_ICM_4S,
+ .vendor = PCI_VENDOR_ID_ACCESIO,
.device = PCI_DEVICE_ID_ACCESIO_PCIE_ICM232_4,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
@@ -2279,6 +2297,13 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
},
{
.vendor = PCI_VENDOR_ID_ACCESIO,
+ .device = PCI_DEVICE_ID_ACCESIO_PCIE_ICM_4S,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .setup = pci_pericom_setup_four_at_eight,
+ },
+ {
+ .vendor = PCI_VENDOR_ID_ACCESIO,
.device = PCI_DEVICE_ID_ACCESIO_MPCIE_ICM232_4,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
@@ -2882,7 +2907,7 @@ enum pci_board_num_t {
pbn_panacom2,
pbn_panacom4,
pbn_plx_romulus,
- pbn_endrun_2_4000000,
+ pbn_endrun_2_3906250,
pbn_oxsemi,
pbn_oxsemi_1_4000000,
pbn_oxsemi_2_4000000,
@@ -3409,10 +3434,10 @@ static struct pciserial_board pci_boards[] = {
* signal now many ports are available
* 2 port 952 Uart support
*/
- [pbn_endrun_2_4000000] = {
+ [pbn_endrun_2_3906250] = {
.flags = FL_BASE0,
.num_ports = 2,
- .base_baud = 4000000,
+ .base_baud = 3906250,
.uart_offset = 0x200,
.first_offset = 0x1000,
},
@@ -3749,6 +3774,12 @@ static const struct pci_device_id blacklist[] = {
{ PCI_VDEVICE(INTEL, 0x0f0c), },
{ PCI_VDEVICE(INTEL, 0x228a), },
{ PCI_VDEVICE(INTEL, 0x228c), },
+ { PCI_VDEVICE(INTEL, 0x4b96), },
+ { PCI_VDEVICE(INTEL, 0x4b97), },
+ { PCI_VDEVICE(INTEL, 0x4b98), },
+ { PCI_VDEVICE(INTEL, 0x4b99), },
+ { PCI_VDEVICE(INTEL, 0x4b9a), },
+ { PCI_VDEVICE(INTEL, 0x4b9b), },
{ PCI_VDEVICE(INTEL, 0x9ce3), },
{ PCI_VDEVICE(INTEL, 0x9ce4), },
@@ -3903,21 +3934,27 @@ pciserial_init_ports(struct pci_dev *dev, const struct pciserial_board *board)
uart.port.flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ;
uart.port.uartclk = board->base_baud * 16;
- if (pci_match_id(pci_use_msi, dev)) {
- dev_dbg(&dev->dev, "Using MSI(-X) interrupts\n");
- pci_set_master(dev);
- rc = pci_alloc_irq_vectors(dev, 1, 1, PCI_IRQ_ALL_TYPES);
+ if (board->flags & FL_NOIRQ) {
+ uart.port.irq = 0;
} else {
- dev_dbg(&dev->dev, "Using legacy interrupts\n");
- rc = pci_alloc_irq_vectors(dev, 1, 1, PCI_IRQ_LEGACY);
- }
- if (rc < 0) {
- kfree(priv);
- priv = ERR_PTR(rc);
- goto err_deinit;
+ if (pci_match_id(pci_use_msi, dev)) {
+ dev_dbg(&dev->dev, "Using MSI(-X) interrupts\n");
+ pci_set_master(dev);
+ uart.port.flags &= ~UPF_SHARE_IRQ;
+ rc = pci_alloc_irq_vectors(dev, 1, 1, PCI_IRQ_ALL_TYPES);
+ } else {
+ dev_dbg(&dev->dev, "Using legacy interrupts\n");
+ rc = pci_alloc_irq_vectors(dev, 1, 1, PCI_IRQ_LEGACY);
+ }
+ if (rc < 0) {
+ kfree(priv);
+ priv = ERR_PTR(rc);
+ goto err_deinit;
+ }
+
+ uart.port.irq = pci_irq_vector(dev, 0);
}
- uart.port.irq = pci_irq_vector(dev, 0);
uart.port.dev = &dev->dev;
for (i = 0; i < nr_ports; i++) {
@@ -4308,7 +4345,7 @@ static const struct pci_device_id serial_pci_tbl[] = {
*/
{ PCI_VENDOR_ID_ENDRUN, PCI_DEVICE_ID_ENDRUN_1588,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_endrun_2_4000000 },
+ pbn_endrun_2_3906250 },
/*
* Quatech cards. These actually have configurable clocks but for
* now we just use the default.
@@ -4932,6 +4969,10 @@ static const struct pci_device_id serial_pci_tbl[] = {
{ PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_DIVA_AUX,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_1_115200 },
+ /* HPE PCI serial device */
+ { PCI_VENDOR_ID_HP_3PAR, PCI_DEVICE_ID_HPE_PCI_SERIAL,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b1_1_115200 },
{ PCI_VENDOR_ID_DCI, PCI_DEVICE_ID_DCI_PCCOM2,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
@@ -5089,8 +5130,30 @@ static const struct pci_device_id serial_pci_tbl[] = {
{ PCI_VENDOR_ID_INTASHIELD, PCI_DEVICE_ID_INTASHIELD_IS400,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, /* 135a.0dc0 */
pbn_b2_4_115200 },
+ /* Brainboxes Devices */
/*
- * BrainBoxes UC-260
+ * Brainboxes UC-101
+ */
+ { PCI_VENDOR_ID_INTASHIELD, 0x0BA1,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0,
+ pbn_b2_2_115200 },
+ /*
+ * Brainboxes UC-235/246
+ */
+ { PCI_VENDOR_ID_INTASHIELD, 0x0AA1,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0,
+ pbn_b2_1_115200 },
+ /*
+ * Brainboxes UC-257
+ */
+ { PCI_VENDOR_ID_INTASHIELD, 0x0861,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0,
+ pbn_b2_2_115200 },
+ /*
+ * Brainboxes UC-260/271/701/756
*/
{ PCI_VENDOR_ID_INTASHIELD, 0x0D21,
PCI_ANY_ID, PCI_ANY_ID,
@@ -5098,7 +5161,81 @@ static const struct pci_device_id serial_pci_tbl[] = {
pbn_b2_4_115200 },
{ PCI_VENDOR_ID_INTASHIELD, 0x0E34,
PCI_ANY_ID, PCI_ANY_ID,
- PCI_CLASS_COMMUNICATION_MULTISERIAL << 8, 0xffff00,
+ PCI_CLASS_COMMUNICATION_MULTISERIAL << 8, 0xffff00,
+ pbn_b2_4_115200 },
+ /*
+ * Brainboxes UC-268
+ */
+ { PCI_VENDOR_ID_INTASHIELD, 0x0841,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0,
+ pbn_b2_4_115200 },
+ /*
+ * Brainboxes UC-275/279
+ */
+ { PCI_VENDOR_ID_INTASHIELD, 0x0881,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0,
+ pbn_b2_8_115200 },
+ /*
+ * Brainboxes UC-302
+ */
+ { PCI_VENDOR_ID_INTASHIELD, 0x08E1,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0,
+ pbn_b2_2_115200 },
+ /*
+ * Brainboxes UC-310
+ */
+ { PCI_VENDOR_ID_INTASHIELD, 0x08C1,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0,
+ pbn_b2_2_115200 },
+ /*
+ * Brainboxes UC-313
+ */
+ { PCI_VENDOR_ID_INTASHIELD, 0x08A3,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0,
+ pbn_b2_2_115200 },
+ /*
+ * Brainboxes UC-320/324
+ */
+ { PCI_VENDOR_ID_INTASHIELD, 0x0A61,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0,
+ pbn_b2_1_115200 },
+ /*
+ * Brainboxes UC-346
+ */
+ { PCI_VENDOR_ID_INTASHIELD, 0x0B02,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0,
+ pbn_b2_4_115200 },
+ /*
+ * Brainboxes UC-357
+ */
+ { PCI_VENDOR_ID_INTASHIELD, 0x0A81,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0,
+ pbn_b2_2_115200 },
+ { PCI_VENDOR_ID_INTASHIELD, 0x0A83,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0,
+ pbn_b2_2_115200 },
+ /*
+ * Brainboxes UC-368
+ */
+ { PCI_VENDOR_ID_INTASHIELD, 0x0C41,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0,
+ pbn_b2_4_115200 },
+ /*
+ * Brainboxes UC-420/431
+ */
+ { PCI_VENDOR_ID_INTASHIELD, 0x0921,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0,
pbn_b2_4_115200 },
/*
* Perle PCI-RAS cards
diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
index 5b673077639b..cb975228726e 100644
--- a/drivers/tty/serial/8250/8250_port.c
+++ b/drivers/tty/serial/8250/8250_port.c
@@ -125,7 +125,8 @@ static const struct serial8250_config uart_config[] = {
.name = "16C950/954",
.fifo_size = 128,
.tx_loadsz = 128,
- .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
+ .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_01,
+ .rxtrig_bytes = {16, 32, 112, 120},
/* UART_CAP_EFR breaks billionon CF bluetooth card. */
.flags = UART_CAP_FIFO | UART_CAP_SLEEP,
},
@@ -314,7 +315,11 @@ static const struct serial8250_config uart_config[] = {
/* Uart divisor latch read */
static int default_serial_dl_read(struct uart_8250_port *up)
{
- return serial_in(up, UART_DLL) | serial_in(up, UART_DLM) << 8;
+ /* Assign these in pieces to truncate any bits above 7. */
+ unsigned char dll = serial_in(up, UART_DLL);
+ unsigned char dlm = serial_in(up, UART_DLM);
+
+ return dll | dlm << 8;
}
/* Uart divisor latch write */
@@ -1258,9 +1263,11 @@ static void autoconfig(struct uart_8250_port *up)
serial_out(up, UART_LCR, 0);
serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO);
- scratch = serial_in(up, UART_IIR) >> 6;
- switch (scratch) {
+ /* Assign this as it is to truncate any bits above 7. */
+ scratch = serial_in(up, UART_IIR);
+
+ switch (scratch >> 6) {
case 0:
autoconfig_8250(up);
break;
@@ -1469,6 +1476,8 @@ static inline void __stop_tx(struct uart_8250_port *p)
if (em485) {
unsigned char lsr = serial_in(p, UART_LSR);
+ p->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS;
+
/*
* To provide required timeing and allow FIFO transfer,
* __stop_tx_rs485() must be called only when both FIFO and
@@ -1538,6 +1547,18 @@ static inline void start_tx_rs485(struct uart_port *port)
if (!(up->port.rs485.flags & SER_RS485_RX_DURING_TX))
serial8250_stop_rx(&up->port);
+ /*
+ * While serial8250_em485_handle_stop_tx() is a noop if
+ * em485->active_timer != &em485->stop_tx_timer, it might happen that
+ * the timer is still armed and triggers only after the current bunch of
+ * chars is send and em485->active_timer == &em485->stop_tx_timer again.
+ * So cancel the timer. There is still a theoretical race condition if
+ * the timer is already running and only comes around to check for
+ * em485->active_timer when &em485->stop_tx_timer is armed again.
+ */
+ if (em485->active_timer == &em485->stop_tx_timer)
+ hrtimer_try_to_cancel(&em485->stop_tx_timer);
+
em485->active_timer = NULL;
mcr = serial8250_in_MCR(up);
@@ -2557,6 +2578,21 @@ static unsigned int serial8250_get_baud_rate(struct uart_port *port,
struct ktermios *old)
{
unsigned int tolerance = port->uartclk / 100;
+ unsigned int min;
+ unsigned int max;
+
+ /*
+ * Handle magic divisors for baud rates above baud_base on SMSC
+ * Super I/O chips. Enable custom rates of clk/4 and clk/8, but
+ * disable divisor values beyond 32767, which are unavailable.
+ */
+ if (port->flags & UPF_MAGIC_MULTIPLIER) {
+ min = port->uartclk / 16 / UART_DIV_MAX >> 1;
+ max = (port->uartclk + tolerance) / 4;
+ } else {
+ min = port->uartclk / 16 / UART_DIV_MAX;
+ max = (port->uartclk + tolerance) / 16;
+ }
/*
* Ask the core to calculate the divisor for us.
@@ -2564,9 +2600,7 @@ static unsigned int serial8250_get_baud_rate(struct uart_port *port,
* slower than nominal still match standard baud rates without
* causing transmission errors.
*/
- return uart_get_baud_rate(port, termios, old,
- port->uartclk / 16 / UART_DIV_MAX,
- (port->uartclk + tolerance) / 16);
+ return uart_get_baud_rate(port, termios, old, min, max);
}
void
@@ -3152,7 +3186,7 @@ static void serial8250_console_restore(struct uart_8250_port *up)
serial8250_set_divisor(port, baud, quot, frac);
serial_port_out(port, UART_LCR, up->lcr);
- serial8250_out_MCR(up, UART_MCR_DTR | UART_MCR_RTS);
+ serial8250_out_MCR(up, up->mcr | UART_MCR_DTR | UART_MCR_RTS);
}
/*
diff --git a/drivers/tty/serial/8250/serial_cs.c b/drivers/tty/serial/8250/serial_cs.c
index c8186a05a453..a05c2b652040 100644
--- a/drivers/tty/serial/8250/serial_cs.c
+++ b/drivers/tty/serial/8250/serial_cs.c
@@ -306,6 +306,7 @@ static int serial_resume(struct pcmcia_device *link)
static int serial_probe(struct pcmcia_device *link)
{
struct serial_info *info;
+ int ret;
dev_dbg(&link->dev, "serial_attach()\n");
@@ -320,7 +321,15 @@ static int serial_probe(struct pcmcia_device *link)
if (do_sound)
link->config_flags |= CONF_ENABLE_SPKR;
- return serial_config(link);
+ ret = serial_config(link);
+ if (ret)
+ goto free_info;
+
+ return 0;
+
+free_info:
+ kfree(info);
+ return ret;
}
static void serial_detach(struct pcmcia_device *link)
@@ -780,6 +789,7 @@ static const struct pcmcia_device_id serial_ids[] = {
PCMCIA_DEVICE_PROD_ID12("Multi-Tech", "MT2834LT", 0x5f73be51, 0x4cd7c09e),
PCMCIA_DEVICE_PROD_ID12("OEM ", "C288MX ", 0xb572d360, 0xd2385b7a),
PCMCIA_DEVICE_PROD_ID12("Option International", "V34bis GSM/PSTN Data/Fax Modem", 0x9d7cd6f5, 0x5cb8bf41),
+ PCMCIA_DEVICE_PROD_ID12("Option International", "GSM-Ready 56K/ISDN", 0x9d7cd6f5, 0xb23844aa),
PCMCIA_DEVICE_PROD_ID12("PCMCIA ", "C336MX ", 0x99bcafe9, 0xaa25bcab),
PCMCIA_DEVICE_PROD_ID12("Quatech Inc", "PCMCIA Dual RS-232 Serial Port Card", 0xc4420b35, 0x92abc92f),
PCMCIA_DEVICE_PROD_ID12("Quatech Inc", "Dual RS-232 Serial Port PC Card", 0xc4420b35, 0x031a380d),
@@ -807,7 +817,6 @@ static const struct pcmcia_device_id serial_ids[] = {
PCMCIA_DEVICE_CIS_PROD_ID12("ADVANTECH", "COMpad-32/85B-4", 0x96913a85, 0xcec8f102, "cis/COMpad4.cis"),
PCMCIA_DEVICE_CIS_PROD_ID123("ADVANTECH", "COMpad-32/85", "1.0", 0x96913a85, 0x8fbe92ae, 0x0877b627, "cis/COMpad2.cis"),
PCMCIA_DEVICE_CIS_PROD_ID2("RS-COM 2P", 0xad20b156, "cis/RS-COM-2P.cis"),
- PCMCIA_DEVICE_CIS_MANF_CARD(0x0013, 0x0000, "cis/GLOBETROTTER.cis"),
PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c1997.", "SERIAL CARD: SL100 1.00.", 0x19ca78af, 0xf964f42b),
PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c1997.", "SERIAL CARD: SL100", 0x19ca78af, 0x71d98e83),
PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c1997.", "SERIAL CARD: SL232 1.00.", 0x19ca78af, 0x69fb7490),
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.