aboutsummaryrefslogtreecommitdiffstatshomepage
path: root/drivers
diff options
context:
space:
mode:
Diffstat (limited to 'drivers')
-rw-r--r--drivers/ata/libahci.c21
-rw-r--r--drivers/ata/sata_sil24.c12
-rw-r--r--drivers/ata/sata_via.c18
-rw-r--r--drivers/char/vt.c2
-rw-r--r--drivers/mtd/mtdchar.c11
-rw-r--r--drivers/mtd/nand/Kconfig21
-rw-r--r--drivers/mtd/nand/r852.c27
-rw-r--r--drivers/pci/quirks.c5
-rw-r--r--drivers/watchdog/wm8350_wdt.c2
9 files changed, 63 insertions, 56 deletions
diff --git a/drivers/ata/libahci.c b/drivers/ata/libahci.c
index 1984a6e89e84..261f86d102e8 100644
--- a/drivers/ata/libahci.c
+++ b/drivers/ata/libahci.c
@@ -541,29 +541,11 @@ static int ahci_scr_write(struct ata_link *link, unsigned int sc_reg, u32 val)
return -EINVAL;
}
-static int ahci_is_device_present(void __iomem *port_mmio)
-{
- u8 status = readl(port_mmio + PORT_TFDATA) & 0xff;
-
- /* Make sure PxTFD.STS.BSY and PxTFD.STS.DRQ are 0 */
- if (status & (ATA_BUSY | ATA_DRQ))
- return 0;
-
- /* Make sure PxSSTS.DET is 3h */
- status = readl(port_mmio + PORT_SCR_STAT) & 0xf;
- if (status != 3)
- return 0;
- return 1;
-}
-
void ahci_start_engine(struct ata_port *ap)
{
void __iomem *port_mmio = ahci_port_base(ap);
u32 tmp;
- if (!ahci_is_device_present(port_mmio))
- return;
-
/* start DMA */
tmp = readl(port_mmio + PORT_CMD);
tmp |= PORT_CMD_START;
@@ -1892,6 +1874,9 @@ static void ahci_error_handler(struct ata_port *ap)
}
sata_pmp_error_handler(ap);
+
+ if (!ata_dev_enabled(ap->link.device))
+ ahci_stop_engine(ap);
}
static void ahci_post_internal_cmd(struct ata_queued_cmd *qc)
diff --git a/drivers/ata/sata_sil24.c b/drivers/ata/sata_sil24.c
index e9250514734b..70b58fe9e5b1 100644
--- a/drivers/ata/sata_sil24.c
+++ b/drivers/ata/sata_sil24.c
@@ -539,12 +539,12 @@ static void sil24_config_port(struct ata_port *ap)
writel(PORT_CS_IRQ_WOC, port + PORT_CTRL_CLR);
/* zero error counters. */
- writel(0x8000, port + PORT_DECODE_ERR_THRESH);
- writel(0x8000, port + PORT_CRC_ERR_THRESH);
- writel(0x8000, port + PORT_HSHK_ERR_THRESH);
- writel(0x0000, port + PORT_DECODE_ERR_CNT);
- writel(0x0000, port + PORT_CRC_ERR_CNT);
- writel(0x0000, port + PORT_HSHK_ERR_CNT);
+ writew(0x8000, port + PORT_DECODE_ERR_THRESH);
+ writew(0x8000, port + PORT_CRC_ERR_THRESH);
+ writew(0x8000, port + PORT_HSHK_ERR_THRESH);
+ writew(0x0000, port + PORT_DECODE_ERR_CNT);
+ writew(0x0000, port + PORT_CRC_ERR_CNT);
+ writew(0x0000, port + PORT_HSHK_ERR_CNT);
/* always use 64bit activation */
writel(PORT_CS_32BIT_ACTV, port + PORT_CTRL_CLR);
diff --git a/drivers/ata/sata_via.c b/drivers/ata/sata_via.c
index 0ecd0f6aa2c0..4730c42a5ee5 100644
--- a/drivers/ata/sata_via.c
+++ b/drivers/ata/sata_via.c
@@ -578,10 +578,24 @@ static void svia_configure(struct pci_dev *pdev)
/*
* vt6421 has problems talking to some drives. The following
- * is the magic fix from Joseph Chan <JosephChan@via.com.tw>.
- * Please add proper documentation if possible.
+ * is the fix from Joseph Chan <JosephChan@via.com.tw>.
+ *
+ * When host issues HOLD, device may send up to 20DW of data
+ * before acknowledging it with HOLDA and the host should be
+ * able to buffer them in FIFO. Unfortunately, some WD drives
+ * send upto 40DW before acknowledging HOLD and, in the
+ * default configuration, this ends up overflowing vt6421's
+ * FIFO, making the controller abort the transaction with
+ * R_ERR.
+ *
+ * Rx52[2] is the internal 128DW FIFO Flow control watermark
+ * adjusting mechanism enable bit and the default value 0
+ * means host will issue HOLD to device when the left FIFO
+ * size goes below 32DW. Setting it to 1 makes the watermark
+ * 64DW.
*
* https://bugzilla.kernel.org/show_bug.cgi?id=15173
+ * http://article.gmane.org/gmane.linux.ide/46352
*/
if (pdev->device == 0x3249) {
pci_read_config_byte(pdev, 0x52, &tmp8);
diff --git a/drivers/char/vt.c b/drivers/char/vt.c
index 1296c42ed5c6..7cdb6ee569cd 100644
--- a/drivers/char/vt.c
+++ b/drivers/char/vt.c
@@ -304,7 +304,7 @@ static void scrup(struct vc_data *vc, unsigned int t, unsigned int b, int nr)
d = (unsigned short *)(vc->vc_origin + vc->vc_size_row * t);
s = (unsigned short *)(vc->vc_origin + vc->vc_size_row * (t + nr));
scr_memmovew(d, s, (b - t - nr) * vc->vc_size_row);
- scr_memsetw(d + (b - t - nr) * vc->vc_size_row, vc->vc_video_erase_char,
+ scr_memsetw(d + (b - t - nr) * vc->vc_cols, vc->vc_video_erase_char,
vc->vc_size_row * nr);
}
diff --git a/drivers/mtd/mtdchar.c b/drivers/mtd/mtdchar.c
index 000d65ea55a4..91c8013cf0d9 100644
--- a/drivers/mtd/mtdchar.c
+++ b/drivers/mtd/mtdchar.c
@@ -404,14 +404,9 @@ static int mtd_do_writeoob(struct file *file, struct mtd_info *mtd,
if (ops.ooboffs && ops.ooblen > (mtd->oobsize - ops.ooboffs))
return -EINVAL;
- ops.oobbuf = kmalloc(length, GFP_KERNEL);
- if (!ops.oobbuf)
- return -ENOMEM;
-
- if (copy_from_user(ops.oobbuf, ptr, length)) {
- kfree(ops.oobbuf);
- return -EFAULT;
- }
+ ops.oobbuf = memdup_user(ptr, length);
+ if (IS_ERR(ops.oobbuf))
+ return PTR_ERR(ops.oobbuf);
start &= ~((uint64_t)mtd->oobsize - 1);
ret = mtd->write_oob(mtd, start, &ops);
diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index 98a04b3c9526..ffc3720929f1 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -1,13 +1,3 @@
-menuconfig MTD_NAND
- tristate "NAND Device Support"
- depends on MTD
- select MTD_NAND_IDS
- select MTD_NAND_ECC
- help
- This enables support for accessing all type of NAND flash
- devices. For further information see
- <http://www.linux-mtd.infradead.org/doc/nand.html>.
-
config MTD_NAND_ECC
tristate
@@ -19,6 +9,17 @@ config MTD_NAND_ECC_SMC
Software ECC according to the Smart Media Specification.
The original Linux implementation had byte 0 and 1 swapped.
+
+menuconfig MTD_NAND
+ tristate "NAND Device Support"
+ depends on MTD
+ select MTD_NAND_IDS
+ select MTD_NAND_ECC
+ help
+ This enables support for accessing all type of NAND flash
+ devices. For further information see
+ <http://www.linux-mtd.infradead.org/doc/nand.html>.
+
if MTD_NAND
config MTD_NAND_VERIFY_WRITE
diff --git a/drivers/mtd/nand/r852.c b/drivers/mtd/nand/r852.c
index 78a423295474..bcfc851fe550 100644
--- a/drivers/mtd/nand/r852.c
+++ b/drivers/mtd/nand/r852.c
@@ -150,7 +150,6 @@ static void r852_dma_done(struct r852_device *dev, int error)
if (dev->phys_dma_addr && dev->phys_dma_addr != dev->phys_bounce_buffer)
pci_unmap_single(dev->pci_dev, dev->phys_dma_addr, R852_DMA_LEN,
dev->dma_dir ? PCI_DMA_FROMDEVICE : PCI_DMA_TODEVICE);
- complete(&dev->dma_done);
}
/*
@@ -182,6 +181,7 @@ static void r852_do_dma(struct r852_device *dev, uint8_t *buf, int do_read)
/* Set dma direction */
dev->dma_dir = do_read;
dev->dma_stage = 1;
+ INIT_COMPLETION(dev->dma_done);
dbg_verbose("doing dma %s ", do_read ? "read" : "write");
@@ -494,6 +494,11 @@ int r852_ecc_correct(struct mtd_info *mtd, uint8_t *dat,
if (dev->card_unstable)
return 0;
+ if (dev->dma_error) {
+ dev->dma_error = 0;
+ return -1;
+ }
+
r852_write_reg(dev, R852_CTL, dev->ctlreg | R852_CTL_ECC_ACCESS);
ecc_reg = r852_read_reg_dword(dev, R852_DATALINE);
r852_write_reg(dev, R852_CTL, dev->ctlreg);
@@ -707,6 +712,7 @@ void r852_card_detect_work(struct work_struct *work)
container_of(work, struct r852_device, card_detect_work.work);
r852_card_update_present(dev);
+ r852_update_card_detect(dev);
dev->card_unstable = 0;
/* False alarm */
@@ -722,7 +728,6 @@ void r852_card_detect_work(struct work_struct *work)
else
r852_unregister_nand_device(dev);
exit:
- /* Update detection logic */
r852_update_card_detect(dev);
}
@@ -796,6 +801,7 @@ static irqreturn_t r852_irq(int irq, void *data)
if (dma_status & R852_DMA_IRQ_ERROR) {
dbg("recieved dma error IRQ");
r852_dma_done(dev, -EIO);
+ complete(&dev->dma_done);
goto out;
}
@@ -825,8 +831,10 @@ static irqreturn_t r852_irq(int irq, void *data)
r852_dma_enable(dev);
/* Operation done */
- if (dev->dma_stage == 3)
+ if (dev->dma_stage == 3) {
r852_dma_done(dev, 0);
+ complete(&dev->dma_done);
+ }
goto out;
}
@@ -940,18 +948,19 @@ int r852_probe(struct pci_dev *pci_dev, const struct pci_device_id *id)
r852_dma_test(dev);
+ dev->irq = pci_dev->irq;
+ spin_lock_init(&dev->irqlock);
+
+ dev->card_detected = 0;
+ r852_card_update_present(dev);
+
/*register irq handler*/
error = -ENODEV;
if (request_irq(pci_dev->irq, &r852_irq, IRQF_SHARED,
DRV_NAME, dev))
goto error10;
- dev->irq = pci_dev->irq;
- spin_lock_init(&dev->irqlock);
-
/* kick initial present test */
- dev->card_detected = 0;
- r852_card_update_present(dev);
queue_delayed_work(dev->card_workqueue,
&dev->card_detect_work, 0);
@@ -1081,7 +1090,7 @@ int r852_resume(struct device *device)
dev->card_detected ? "added" : "removed");
queue_delayed_work(dev->card_workqueue,
- &dev->card_detect_work, 1000);
+ &dev->card_detect_work, msecs_to_jiffies(1000));
return 0;
}
diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c
index b7512cf08c58..477345d41641 100644
--- a/drivers/pci/quirks.c
+++ b/drivers/pci/quirks.c
@@ -1457,7 +1457,8 @@ static void quirk_jmicron_ata(struct pci_dev *pdev)
conf5 &= ~(1 << 24); /* Clear bit 24 */
switch (pdev->device) {
- case PCI_DEVICE_ID_JMICRON_JMB360:
+ case PCI_DEVICE_ID_JMICRON_JMB360: /* SATA single port */
+ case PCI_DEVICE_ID_JMICRON_JMB362: /* SATA dual ports */
/* The controller should be in single function ahci mode */
conf1 |= 0x0002A100; /* Set 8, 13, 15, 17 */
break;
@@ -1493,12 +1494,14 @@ static void quirk_jmicron_ata(struct pci_dev *pdev)
}
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB360, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB361, quirk_jmicron_ata);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB362, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB363, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB365, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB366, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB368, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB360, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB361, quirk_jmicron_ata);
+DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB362, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB363, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB365, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB366, quirk_jmicron_ata);
diff --git a/drivers/watchdog/wm8350_wdt.c b/drivers/watchdog/wm8350_wdt.c
index 89dd7b035295..b68d928c8f90 100644
--- a/drivers/watchdog/wm8350_wdt.c
+++ b/drivers/watchdog/wm8350_wdt.c
@@ -284,7 +284,7 @@ static int __devinit wm8350_wdt_probe(struct platform_device *pdev)
struct wm8350 *wm8350 = platform_get_drvdata(pdev);
if (!wm8350) {
- dev_err(wm8350->dev, "No driver data supplied\n");
+ pr_err("No driver data supplied\n");
return -ENODEV;
}
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.