aboutsummaryrefslogtreecommitdiffstatshomepage
AgeCommit message (Collapse)AuthorFilesLines
2018-12-11usb: chipidea: imx: Warn if oc polarity isn't specifiedUwe Kleine-König1-0/+2
The polarity of the over current detection pin isn't configured on i.MX6/7 if it's unspecified in the device tree. So the actual configuration depends on bootloader behavior which is bad. So encourage users to fix their device tree by issuing a warning in this case. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Peter Chen <peter.chen@nxp.com>
2018-12-11usb: chipidea: imx: support configuring for active low oc signalUwe Kleine-König4-14/+43
The status quo on i.MX6 is that if "over-current-active-high" is specified in the device tree this is configured as expected. If the property is missing polarity isn't changed and so the polarity is kept as setup by the bootloader. Reset default is active high, so active low can only be used with help by the bootloader. On i.MX7 it is similar, but there disabling of over current detection has a similar inconsistency. This patch introduces a new property that allows to explicitly configure for active low over current detection and consistently sets this up. In the absence of an explicit configuration the bit is kept as is. On i.MX7 over current detection is used unless disabled in the device tree. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Peter Chen <peter.chen@nxp.com>
2018-12-11doc: usb: ci-hdrc-usb2: Add pinctrl properties for HSIC pin groupsPeter Chen1-1/+30
For USB HSIC, the data and strobe pin needs to be pulled down at default, we consider it as "idle" state. When the USB host is ready to be used, the strobe pin needs to be pulled up, we consider it as "active" state. Signed-off-by: Peter Chen <peter.chen@nxp.com>
2018-12-11usb: chipidea: host: override ehci->hub_controlPeter Chen1-0/+75
The chipidea controller has some special requirements during suspend/resume, override common ehci->hub_control to implement it. Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de> Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de> Signed-off-by: Peter Chen <peter.chen@nxp.com>
2018-12-11usb: chipidea: imx: add HSIC supportPeter Chen3-19/+270
To support imx HSIC, there are some special requirement: - The HSIC pad is 1.2v, it may need to supply from external - The data/strobe pin needs to be pulled down first, and after host mode is initialized, the strobe pin needs to be pulled up - During the USB suspend/resume, special setting is needed Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de> Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de> Signed-off-by: Peter Chen <peter.chen@nxp.com>
2018-12-11usb: chipidea: add flag for imx hsic implementationPeter Chen2-0/+20
NXP (Freecale) imx HSIC design has some special requirements, add some flags at host code to handle them. Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de> Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de> Signed-off-by: Peter Chen <peter.chen@nxp.com>
2018-12-07xhci: move usb2 get port status link resume handling to its own functionMathias Nyman1-84/+104
Refactoring, no functional changes. But worth mentioning that checking for port link resume state is now behind a additional port power check. This is fine as ports can't be in resume state if port power bit is not set. xhci spec section 4.19.1.1.6 figure 34 shows that port power bit must be set for all 'Enable' substates, including U0,U1,U2,U3 (suspended), Resume, and RExit states. Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-07xhci: refactor U0 link state handling in get_port_statusMathias Nyman1-13/+19
Move U0 link state handing to USB3 and USB2 specific functions Note that bus_state->resuming_ports: bus_state->resume_done[]: are only used for USB2, and don't need to cleared for USB3 ports No functional changes Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-07xhci: cleanup code that sets portstatus and portchange bitsMathias Nyman1-12/+14
Group the code where the wPortstatus and wPortChange bits are set into one place. No functional changes Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-07xhci: move usb2 speficic bits to own function in get_port_status callMathias Nyman1-20/+24
Mostly refactoring, with the exception that USB_PORT_STAT_L1 link state is reported if xhci port link is in U2 AND port is powered. Previously we did not check if the port was powered, but according to xhci spec 4.19.1.1.6 All the 'Enabled' states, including USB_PORT_STAT_L1 (U2), U1, U0 and U3 must have Port power bit set. Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-07xhci: move usb3 speficic bits to own function in get_port_status callMathias Nyman1-28/+40
refactoring, no functional changes Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-07xhci: remove unused hcd_index()Mathias Nyman1-7/+0
Now that each root hub has their own bus_state strucure the hcd_undex() used to get the correct bus_state strucure is no longer needed. No functional changes Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-07xhci: move bus_state structure under the xhci_hub structure.Mathias Nyman5-26/+24
Move the bus_state structure under struct usb_hub. We need a bus_state strucure for each roothub to keep track of suspend related info for each port. Instead of keeping an array of two bus_state structures right under struct xhci, it makes more sense move them to the xhci_hub structure. No functional changes. Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-07xhci: remove the unused sw_lpm_supportZeng Tao3-20/+5
It is introduced for the pre-0.96 xHC controllers, and the driver only support HW LPM for 1.0 and later controllers.It's not actually used now and is thought not to be used in the future any more, so just remove it. Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-05usb: appledisplay: Remove unnecessary spinlockAlexander Theissen1-7/+0
The spinlock was inside the urb completion function which is only called once per display and is then resubmitted from this function. There was no other place where this lock was used. Signed-off-by: Alexander Theissen <alex.theissen@me.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-05usb: appledisplay: Set urb transfer_flags to URB_NO_TRANSFER_DMA_MAPAlexander Theissen1-0/+1
The driver does allocate a DMA address with usb_alloc_coherent but did not set the appropriate flag to signal that transfer_dma is set to a valid value. Signed-off-by: Alexander Theissen <alex.theissen@me.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-05staging: typec: fusb302: Rename fcs,extcon-name to linux,extcon-nameAndy Shevchenko2-2/+2
Since we are going to use the same in Designware USB 3 driver, rename the property to be consistent across the drivers. No functional change intended. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Guenter Roeck <linux@roeck-us.net> Acked-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-05usb: mtu3: clear SOFTCONN when clear USB3_EN if work as HS modeChunfeng Yun2-0/+7
When the controller supports SS mode, but works as HS mode, the SOFTCONN will not be cleared automatically when clear USB3_EN by default, this cause an issue that can't disconnect from host, so clear SOFTCONN when clear USB3_EN when the class driver want to disable the D+ pullup. Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-05usb: mtu3: enable SETUPENDISR interruptChunfeng Yun3-2/+7
If the controller receives a new SETUP during SETUP data stage, and will generate SETUPENDISR interrupt, the driver should abort the current SETUP command and process the new one. Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-05usb: mtu3: fix the issue about SetFeature(U1/U2_Enable)Chunfeng Yun2-5/+7
Fix the issue: device doesn't accept LGO_U1/U2: 1. set SW_U1/U2_ACCEPT_ENABLE to eanble controller to accept LGO_U1/U2 by default; 2. enable/disable controller to initiate requests for transition into U1/U2 by SW_U1/U2_REQUEST_ENABLE instead of SW_U1/U2_ACCEPT_ENABLE; Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-05usb: mtu3: enable hardware remote wakeup from L1 automaticallyChunfeng Yun1-7/+3
Enable hardware remote wakeup from L1 automatically based on the FIFO status, instead of manual way. Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-05usb: mtu3: remove QMU checksumChunfeng Yun2-28/+0
The QMU checksum calculation is redundant, mostly used by debug, so remove it here. Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-05usb/mtu3: power down device ip at setupHsin-Yi, Wang1-0/+8
Originally, when dr_mode is USB_DR_MODE_HOST, it didn't power down device ip, so host ip sleep will fail at ssusb_host_disable. Power down device ip at ssusb_host_setup. Signed-off-by: Hsin-Yi, Wang <hsinyi@chromium.org> Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-05usb: hub: delay hub autosuspend if USB3 port is still link trainingMathias Nyman1-0/+10
When initializing a hub we want to give a USB3 port in link training the same debounce delay time before autosuspening the hub as already trained, connected enabled ports. USB3 ports won't reach the enabled state with "current connect status" and "connect status change" bits set until the USB3 link training finishes. Catching the port in link training (polling) and adding the debounce delay prevents unnecessary failed attempts to autosuspend the hub. Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-03Merge 4.20-rc5 into usb-nextGreg Kroah-Hartman388-2282/+4643
We need the USB fixes into usb-next. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-02Linux 4.20-rc5Linus Torvalds1-1/+1
2018-12-02Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-socLinus Torvalds24-33/+176
Pull ARM SoC fixes from Olof Johansson: "Volume is a little higher than usual due to a set of gpio fixes for Davinci platforms that's been around a while, still seemed appropriate to not hold off until next merge window. Besides that it's the usual mix of minor fixes, mostly corrections of small stuff in device trees. Major stability-related one is the removal of a regulator from DT on Rock960, since DVFS caused undervoltage. I expect it'll be restored once they figure out the underlying issue" * tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits) MAINTAINERS: Remove unused Qualcomm SoC mailing list ARM: davinci: dm644x: set the GPIO base to 0 ARM: davinci: da830: set the GPIO base to 0 ARM: davinci: dm355: set the GPIO base to 0 ARM: davinci: dm646x: set the GPIO base to 0 ARM: davinci: dm365: set the GPIO base to 0 ARM: davinci: da850: set the GPIO base to 0 gpio: davinci: restore a way to manually specify the GPIO base ARM: davinci: dm644x: define gpio interrupts as separate resources ARM: davinci: dm355: define gpio interrupts as separate resources ARM: davinci: dm646x: define gpio interrupts as separate resources ARM: davinci: dm365: define gpio interrupts as separate resources ARM: davinci: da8xx: define gpio interrupts as separate resources ARM: dts: at91: sama5d2: use the divided clock for SMC ARM: dts: imx51-zii-rdu1: Remove EEPROM node ARM: dts: rockchip: Remove @0 from the veyron memory node arm64: dts: rockchip: Fix PCIe reset polarity for rk3399-puma-haikou. arm64: dts: qcom: msm8998: Reserve gpio ranges on MTP arm64: dts: sdm845-mtp: Reserve reserved gpios arm64: dts: ti: k3-am654: Fix wakeup_uart reg address ...
2018-12-02Merge tag 'for-linus-4.20a-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tipLinus Torvalds8-164/+37
Pull xen fixes from Juergen Gross: - A revert of a previous commit as it is no longer necessary and has shown to cause problems in some memory hotplug cases. - Some small fixes and a minor cleanup. - A patch for adding better diagnostic data in a very rare failure case. * tag 'for-linus-4.20a-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: pvcalls-front: fixes incorrect error handling Revert "xen/balloon: Mark unallocated host memory as UNUSABLE" xen: xlate_mmu: add missing header to fix 'W=1' warning xen/x86: add diagnostic printout to xen_mc_flush() in case of error x86/xen: cleanup includes in arch/x86/xen/spinlock.c
2018-12-02Merge tag 'dmaengine-fix-4.20-rc5' of git://git.infradead.org/users/vkoul/slave-dmaLinus Torvalds1-1/+9
Pull dmaengine fixes from Vinod Koul: "This contains two fixes to at_hdmac which fixes long standing bus reported recently on serial transfers causing memory leak. These fixes were done by Richard Genoud" * tag 'dmaengine-fix-4.20-rc5' of git://git.infradead.org/users/vkoul/slave-dma: dmaengine: at_hdmac: fix module unloading dmaengine: at_hdmac: fix memory leak in at_dma_xlate()
2018-12-01Merge branch 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds26-282/+780
Pull STIBP fallout fixes from Thomas Gleixner: "The performance destruction department finally got it's act together and came up with a cure for the STIPB regression: - Provide a command line option to control the spectre v2 user space mitigations. Default is either seccomp or prctl (if seccomp is disabled in Kconfig). prctl allows mitigation opt-in, seccomp enables the migitation for sandboxed processes. - Rework the code to handle the conditional STIBP/IBPB control and remove the now unused ptrace_may_access_sched() optimization attempt - Disable STIBP automatically when SMT is disabled - Optimize the switch_to() logic to avoid MSR writes and invocations of __switch_to_xtra(). - Make the asynchronous speculation TIF updates synchronous to prevent stale mitigation state. As a general cleanup this also makes retpoline directly depend on compiler support and removes the 'minimal retpoline' option which just pretended to provide some form of security while providing none" * 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (31 commits) x86/speculation: Provide IBPB always command line options x86/speculation: Add seccomp Spectre v2 user space protection mode x86/speculation: Enable prctl mode for spectre_v2_user x86/speculation: Add prctl() control for indirect branch speculation x86/speculation: Prepare arch_smt_update() for PRCTL mode x86/speculation: Prevent stale SPEC_CTRL msr content x86/speculation: Split out TIF update ptrace: Remove unused ptrace_may_access_sched() and MODE_IBRS x86/speculation: Prepare for conditional IBPB in switch_mm() x86/speculation: Avoid __switch_to_xtra() calls x86/process: Consolidate and simplify switch_to_xtra() code x86/speculation: Prepare for per task indirect branch speculation control x86/speculation: Add command line control for indirect branch speculation x86/speculation: Unify conditional spectre v2 print functions x86/speculataion: Mark command line parser data __initdata x86/speculation: Mark string arrays const correctly x86/speculation: Reorder the spec_v2 code x86/l1tf: Show actual SMT state x86/speculation: Rework SMT state change sched/smt: Expose sched_smt_present static key ...
2018-12-01Merge tag 'for-linus-20181201' of git://git.kernel.dk/linux-blockLinus Torvalds6-7/+14
Pull block layer fixes from Jens Axboe: - Single range elevator discard merge fix, that caused crashes (Ming) - Fix for a regression in O_DIRECT, where we could potentially lose the error value (Maximilian Heyne) - NVMe pull request from Christoph, with little fixes all over the map for NVMe. * tag 'for-linus-20181201' of git://git.kernel.dk/linux-block: block: fix single range discard merge nvme-rdma: fix double freeing of async event data nvme: flush namespace scanning work just before removing namespaces nvme: warn when finding multi-port subsystems without multipathing enabled fs: fix lost error code in dio_complete nvme-pci: fix surprise removal nvme-fc: initialize nvme_req(rq)->ctrl after calling __nvme_fc_init_request() nvme: Free ctrl device name on init failure
2018-12-01Merge tag 'pci-v4.20-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pciLinus Torvalds4-24/+13
Pull PCI fixes from Bjorn Helgaas: - Fix a link speed checking interface that broke PCIe gen3 cards in gen1 slots (Mikulas Patocka) - Fix an imx6 link training error (Trent Piepho) - Fix a layerscape outbound window accessor calling error (Hou Zhiqiang) - Fix a DesignWare endpoint MSI-X address calculation error (Gustavo Pimentel) * tag 'pci-v4.20-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: PCI: Fix incorrect value returned from pcie_get_speed_cap() PCI: dwc: Fix MSI-X EP framework address calculation bug PCI: layerscape: Fix wrong invocation of outbound window disable accessor PCI: imx6: Fix link training status detection in link up check
2018-11-30Merge remote-tracking branch 'lorenzo/pci/controller-fixes' into for-linusBjorn Helgaas3-11/+2
- Fix DesignWare endpoint MSI-X address calculation bug (Gustavo Pimentel) - Fix Layerscape outbound window disable usage (Hou Zhiqiang) - Fix imx6 link up detection (Trent Piepho) * lorenzo/pci/controller-fixes: PCI: dwc: Fix MSI-X EP framework address calculation bug PCI: layerscape: Fix wrong invocation of outbound window disable accessor PCI: imx6: Fix link training status detection in link up check
2018-11-30PCI: Fix incorrect value returned from pcie_get_speed_cap()Mikulas Patocka1-13/+11
The macros PCI_EXP_LNKCAP_SLS_*GB are values, not bit masks. We must mask the register and compare it against them. This fixes errors like this: amdgpu: [powerplay] failed to send message 261 ret is 0 when a PCIe-v3 card is plugged into a PCIe-v1 slot, because the slot is being incorrectly reported as PCIe-v3 capable. 6cf57be0f78e, which appeared in v4.17, added pcie_get_speed_cap() with the incorrect test of PCI_EXP_LNKCAP_SLS as a bitmask. 5d9a63304032, which appeared in v4.19, changed amdgpu to use pcie_get_speed_cap(), so the amdgpu bug reports below are regressions in v4.19. Fixes: 6cf57be0f78e ("PCI: Add pcie_get_speed_cap() to find max supported link speed") Fixes: 5d9a63304032 ("drm/amdgpu: use pcie functions for link width and speed") Link: https://bugs.freedesktop.org/show_bug.cgi?id=108704 Link: https://bugs.freedesktop.org/show_bug.cgi?id=108778 Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> [bhelgaas: update comment, remove use of PCI_EXP_LNKCAP_SLS_8_0GB and PCI_EXP_LNKCAP_SLS_16_0GB since those should be covered by PCI_EXP_LNKCAP2, remove test of PCI_EXP_LNKCAP for zero, since that register is required] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org # v4.17+
2018-11-30Merge branch 'akpm' (patches from Andrew)Linus Torvalds25-177/+319
Merge misc fixes from Andrew Morton: "31 fixes" * emailed patches from Andrew Morton <akpm@linux-foundation.org>: (31 commits) ocfs2: fix potential use after free mm/khugepaged: fix the xas_create_range() error path mm/khugepaged: collapse_shmem() do not crash on Compound mm/khugepaged: collapse_shmem() without freezing new_page mm/khugepaged: minor reorderings in collapse_shmem() mm/khugepaged: collapse_shmem() remember to clear holes mm/khugepaged: fix crashes due to misaccounted holes mm/khugepaged: collapse_shmem() stop if punched or truncated mm/huge_memory: fix lockdep complaint on 32-bit i_size_read() mm/huge_memory: splitting set mapping+index before unfreeze mm/huge_memory: rename freeze_page() to unmap_page() initramfs: clean old path before creating a hardlink kernel/kcov.c: mark funcs in __sanitizer_cov_trace_pc() as notrace psi: make disabling/enabling easier for vendor kernels proc: fixup map_files test on arm debugobjects: avoid recursive calls with kmemleak userfaultfd: shmem: UFFDIO_COPY: set the page dirty if VM_WRITE is not set userfaultfd: shmem: add i_size checks userfaultfd: shmem/hugetlbfs: only allow to register VM_MAYWRITE vmas userfaultfd: shmem: allocate anonymous memory for MAP_PRIVATE shmem ...
2018-11-30Merge tag 'mips_fixes_4.20_4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linuxLinus Torvalds3-25/+25
Pull few more MIPS fixes from Paul Burton: - Fix mips_get_syscall_arg() to operate on the task specified when detecting o32 tasks running on MIPS64 kernels. - Fix some incorrect GPIO pin muxing for the MT7620 SoC. - Update the linux-mips mailing list address. * tag 'mips_fixes_4.20_4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: MAINTAINERS: Update linux-mips mailing list address MIPS: ralink: Fix mt7620 nd_sd pinmux mips: fix mips_get_syscall_arg o32 check
2018-11-30Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linuxLinus Torvalds6-6/+59
Pull arm64 fixes from Catalin Marinas: - Cortex-A76 erratum workaround - ftrace fix to enable syscall events on arm64 - Fix uninitialised pointer in iort_get_platform_device_domain() * tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: ACPI/IORT: Fix iort_get_platform_device_domain() uninitialized pointer value arm64: ftrace: Fix to enable syscall events on arm64 arm64: Add workaround for Cortex-A76 erratum 1286807
2018-11-30Merge tag 'gcc-plugins-v4.20-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linuxLinus Torvalds1-1/+3
Pull stackleak plugin fix from Kees Cook: "Fix crash by not allowing kprobing of stackleak_erase() (Alexander Popov)" * tag 'gcc-plugins-v4.20-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: stackleak: Disable function tracing and kprobes for stackleak_erase()
2018-11-30Merge tag 'fscache-fixes-20181130' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fsLinus Torvalds5-9/+17
Pull fscache and cachefiles fixes from David Howells: "Misc fixes: - Fix an assertion failure at fs/cachefiles/xattr.c:138 caused by a race between a cache object lookup failing and someone attempting to reenable that object, thereby triggering an update of the object's attributes. - Fix an assertion failure at fs/fscache/operation.c:449 caused by a split atomic subtract and atomic read that allows a race to happen. - Fix a leak of backing pages when simultaneously reading the same page from the same object from two or more threads. - Fix a hang due to a race between a cache object being discarded and the corresponding cookie being reenabled. There are also some minor cleanups: - Cast an enum value to a different enum type to prevent clang from generating a warning. This shouldn't cause any sort of change in the emitted code. - Use ktime_get_real_seconds() instead of get_seconds(). This is just used to uniquify a filename for an object to be placed in the graveyard. Objects placed there are deleted by cachfilesd in userspace immediately thereafter. - Remove an initialised, but otherwise unused variable. This should have been entirely optimised away anyway" * tag 'fscache-fixes-20181130' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: fscache, cachefiles: remove redundant variable 'cache' cachefiles: avoid deprecated get_seconds() cachefiles: Explicitly cast enumerated type in put_object fscache: fix race between enablement and dropping of object cachefiles: Fix page leak in cachefiles_read_backing_file while vmscan is active fscache: Fix race in fscache_op_complete() due to split atomic_sub & read cachefiles: Fix an assertion failure when trying to update a failed object
2018-11-30MAINTAINERS: Update linux-mips mailing list addressPaul Burton1-23/+23
The linux-mips.org infrastructure has been unreliable recently & nobody with sufficient access to fix it is around to do so. As a result we're moving away from it, and part of this is migrating our mailing list to kernel.org. Replace all instances of linux-mips@linux-mips.org in MAINTAINERS with the shiny new linux-mips@vger.kernel.org address. The new list is now being archived on kernel.org at https://lore.kernel.org/linux-mips/ which also holds the history of the old linux-mips.org list. Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: linux-mips@vger.kernel.org Cc: linux-mips@linux-mips.org
2018-11-30ocfs2: fix potential use after freePan Bian1-1/+1
ocfs2_get_dentry() calls iput(inode) to drop the reference count of inode, and if the reference count hits 0, inode is freed. However, in this function, it then reads inode->i_generation, which may result in a use after free bug. Move the put operation later. Link: http://lkml.kernel.org/r/1543109237-110227-1-git-send-email-bianpan2016@163.com Fixes: 781f200cb7a("ocfs2: Remove masklog ML_EXPORT.") Signed-off-by: Pan Bian <bianpan2016@163.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Joseph Qi <jiangqi903@gmail.com> Cc: Changwei Ge <ge.changwei@h3c.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-11-30mm/khugepaged: fix the xas_create_range() error pathHugh Dickins1-11/+14
collapse_shmem()'s xas_nomem() is very unlikely to fail, but it is rightly given a failure path, so move the whole xas_create_range() block up before __SetPageLocked(new_page): so that it does not need to remember to unlock_page(new_page). Add the missing mem_cgroup_cancel_charge(), and set (currently unused) result to SCAN_FAIL rather than SCAN_SUCCEED. Link: http://lkml.kernel.org/r/alpine.LSU.2.11.1811261531200.2275@eggly.anvils Fixes: 77da9389b9d5 ("mm: Convert collapse_shmem to XArray") Signed-off-by: Hugh Dickins <hughd@kernel.org> Cc: Matthew Wilcox <willy@infradead.org> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-11-30mm/khugepaged: collapse_shmem() do not crash on CompoundHugh Dickins1-1/+9
collapse_shmem()'s VM_BUG_ON_PAGE(PageTransCompound) was unsafe: before it holds page lock of the first page, racing truncation then extension might conceivably have inserted a hugepage there already. Fail with the SCAN_PAGE_COMPOUND result, instead of crashing (CONFIG_DEBUG_VM=y) or otherwise mishandling the unexpected hugepage - though later we might code up a more constructive way of handling it, with SCAN_SUCCESS. Link: http://lkml.kernel.org/r/alpine.LSU.2.11.1811261529310.2275@eggly.anvils Fixes: f3f0e1d2150b2 ("khugepaged: add support of collapse for tmpfs/shmem pages") Signed-off-by: Hugh Dickins <hughd@google.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Cc: Matthew Wilcox <willy@infradead.org> Cc: <stable@vger.kernel.org> [4.8+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-11-30mm/khugepaged: collapse_shmem() without freezing new_pageHugh Dickins1-12/+7
khugepaged's collapse_shmem() does almost all of its work, to assemble the huge new_page from 512 scattered old pages, with the new_page's refcount frozen to 0 (and refcounts of all old pages so far also frozen to 0). Including shmem_getpage() to read in any which were out on swap, memory reclaim if necessary to allocate their intermediate pages, and copying over all the data from old to new. Imagine the frozen refcount as a spinlock held, but without any lock debugging to highlight the abuse: it's not good, and under serious load heads into lockups - speculative getters of the page are not expecting to spin while khugepaged is rescheduled. One can get a little further under load by hacking around elsewhere; but fortunately, freezing the new_page turns out to have been entirely unnecessary, with no hacks needed elsewhere. The huge new_page lock is already held throughout, and guards all its subpages as they are brought one by one into the page cache tree; and anything reading the data in that page, without the lock, before it has been marked PageUptodate, would already be in the wrong. So simply eliminate the freezing of the new_page. Each of the old pages remains frozen with refcount 0 after it has been replaced by a new_page subpage in the page cache tree, until they are all unfrozen on success or failure: just as before. They could be unfrozen sooner, but cause no problem once no longer visible to find_get_entry(), filemap_map_pages() and other speculative lookups. Link: http://lkml.kernel.org/r/alpine.LSU.2.11.1811261527570.2275@eggly.anvils Fixes: f3f0e1d2150b2 ("khugepaged: add support of collapse for tmpfs/shmem pages") Signed-off-by: Hugh Dickins <hughd@google.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Cc: Matthew Wilcox <willy@infradead.org> Cc: <stable@vger.kernel.org> [4.8+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-11-30mm/khugepaged: minor reorderings in collapse_shmem()Hugh Dickins1-40/+32
Several cleanups in collapse_shmem(): most of which probably do not really matter, beyond doing things in a more familiar and reassuring order. Simplify the failure gotos in the main loop, and on success update stats while interrupts still disabled from the last iteration. Link: http://lkml.kernel.org/r/alpine.LSU.2.11.1811261526400.2275@eggly.anvils Fixes: f3f0e1d2150b2 ("khugepaged: add support of collapse for tmpfs/shmem pages") Signed-off-by: Hugh Dickins <hughd@google.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Cc: Matthew Wilcox <willy@infradead.org> Cc: <stable@vger.kernel.org> [4.8+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-11-30mm/khugepaged: collapse_shmem() remember to clear holesHugh Dickins1-0/+10
Huge tmpfs testing reminds us that there is no __GFP_ZERO in the gfp flags khugepaged uses to allocate a huge page - in all common cases it would just be a waste of effort - so collapse_shmem() must remember to clear out any holes that it instantiates. The obvious place to do so, where they are put into the page cache tree, is not a good choice: because interrupts are disabled there. Leave it until further down, once success is assured, where the other pages are copied (before setting PageUptodate). Link: http://lkml.kernel.org/r/alpine.LSU.2.11.1811261525080.2275@eggly.anvils Fixes: f3f0e1d2150b2 ("khugepaged: add support of collapse for tmpfs/shmem pages") Signed-off-by: Hugh Dickins <hughd@google.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Cc: Matthew Wilcox <willy@infradead.org> Cc: <stable@vger.kernel.org> [4.8+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-11-30mm/khugepaged: fix crashes due to misaccounted holesHugh Dickins2-2/+9
Huge tmpfs testing on a shortish file mapped into a pmd-rounded extent hit shmem_evict_inode()'s WARN_ON(inode->i_blocks) followed by clear_inode()'s BUG_ON(inode->i_data.nrpages) when the file was later closed and unlinked. khugepaged's collapse_shmem() was forgetting to update mapping->nrpages on the rollback path, after it had added but then needs to undo some holes. There is indeed an irritating asymmetry between shmem_charge(), whose callers want it to increment nrpages after successfully accounting blocks, and shmem_uncharge(), when __delete_from_page_cache() already decremented nrpages itself: oh well, just add a comment on that to them both. And shmem_recalc_inode() is supposed to be called when the accounting is expected to be in balance (so it can deduce from imbalance that reclaim discarded some pages): so change shmem_charge() to update nrpages earlier (though it's rare for the difference to matter at all). Link: http://lkml.kernel.org/r/alpine.LSU.2.11.1811261523450.2275@eggly.anvils Fixes: 800d8c63b2e98 ("shmem: add huge pages support") Fixes: f3f0e1d2150b2 ("khugepaged: add support of collapse for tmpfs/shmem pages") Signed-off-by: Hugh Dickins <hughd@google.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Cc: Matthew Wilcox <willy@infradead.org> Cc: <stable@vger.kernel.org> [4.8+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-11-30mm/khugepaged: collapse_shmem() stop if punched or truncatedHugh Dickins1-0/+11
Huge tmpfs testing showed that although collapse_shmem() recognizes a concurrently truncated or hole-punched page correctly, its handling of holes was liable to refill an emptied extent. Add check to stop that. Link: http://lkml.kernel.org/r/alpine.LSU.2.11.1811261522040.2275@eggly.anvils Fixes: f3f0e1d2150b2 ("khugepaged: add support of collapse for tmpfs/shmem pages") Signed-off-by: Hugh Dickins <hughd@google.com> Reviewed-by: Matthew Wilcox <willy@infradead.org> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Cc: <stable@vger.kernel.org> [4.8+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-11-30mm/huge_memory: fix lockdep complaint on 32-bit i_size_read()Hugh Dickins1-6/+13
Huge tmpfs testing, on 32-bit kernel with lockdep enabled, showed that __split_huge_page() was using i_size_read() while holding the irq-safe lru_lock and page tree lock, but the 32-bit i_size_read() uses an irq-unsafe seqlock which should not be nested inside them. Instead, read the i_size earlier in split_huge_page_to_list(), and pass the end offset down to __split_huge_page(): all while holding head page lock, which is enough to prevent truncation of that extent before the page tree lock has been taken. Link: http://lkml.kernel.org/r/alpine.LSU.2.11.1811261520070.2275@eggly.anvils Fixes: baa355fd33142 ("thp: file pages support for split_huge_page()") Signed-off-by: Hugh Dickins <hughd@google.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Cc: Matthew Wilcox <willy@infradead.org> Cc: <stable@vger.kernel.org> [4.8+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-11-30mm/huge_memory: splitting set mapping+index before unfreezeHugh Dickins1-6/+6
Huge tmpfs stress testing has occasionally hit shmem_undo_range()'s VM_BUG_ON_PAGE(page_to_pgoff(page) != index, page). Move the setting of mapping and index up before the page_ref_unfreeze() in __split_huge_page_tail() to fix this: so that a page cache lookup cannot get a reference while the tail's mapping and index are unstable. In fact, might as well move them up before the smp_wmb(): I don't see an actual need for that, but if I'm missing something, this way round is safer than the other, and no less efficient. You might argue that VM_BUG_ON_PAGE(page_to_pgoff(page) != index, page) is misplaced, and should be left until after the trylock_page(); but left as is has not crashed since, and gives more stringent assurance. Link: http://lkml.kernel.org/r/alpine.LSU.2.11.1811261516380.2275@eggly.anvils Fixes: e9b61f19858a5 ("thp: reintroduce split_huge_page()") Requires: 605ca5ede764 ("mm/huge_memory.c: reorder operations in __split_huge_page_tail()") Signed-off-by: Hugh Dickins <hughd@google.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: <stable@vger.kernel.org> [4.8+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.