| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The QCA6174 in combination with new wmi-tlv firmware is capable of
multi-channel, beamforming, tdls and other features.
This patch just makes it possible to boot these devices and do some basic stuff
like connect to an AP without encryption. Some things may not work or may be
unreliable. New features will be implemented later. This will be addressed
eventually with future patches.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The QCA6174 chip has an extra 4 bytes in
rx_ppdu_end structure which is used in htt_rx_desc
and HTT Rx ring offset setup. This is necessary
for correct Rx for QCA6174 (otherwise Rx
descriptors are overwritten and corrupted).
This means QCA988X will have an extra 4 byte
padding in Rx descriptor layout which is harmless.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
There are some very rare cases with some hardware
configuration that the device doesn't init quickly
enough in which case reading chip_id yielded 0.
This caused driver to subsequently fail to setup
the device.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
New firmware and firmware (qca6174 hw3.0+ and fw
266+) are capable of full aggregation rx
reordering. If it's enabled then Rx is handled via
a new, separate htt event.
The rx ring behaviour is changed a little to
support the new rx scheme. These changes shouldn't
affect qca988x performance.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
It doesn't make much sense to share the
ath10k_skb_cb with Rx path. The Rx path doesn't
need to keep any mac80211's data.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Some firmware revisions may report this event as
part of their diagnostics.
This avoids `unknown event` warnings and adds
tracing for the event.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Some firmware revisions may report this event as
part of their diagnostics.
This avoids `unknown event` warnings and adds
tracing for the event.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
To be compliant with the hwmon interface the unit needs to be
millidegree Celsius. Fix that.
Reported-by: Matthias Kaehlcke <mka@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add a comment for indicating that the ATH10K_SCAN_RUNNING case falls
through to the ATH10K_SCAN_ABORTING case in __ath10k_scan_finish. This
will document that the lack of a break is intentional.
Coverity: CID 1260017
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Originally the explicit fw register dump was added
to wait_for_target_init because interrupts are
masked early during power_up.
Due to some changes in power_up/reset sequences
sometimes when fw crashed ath10k would print the
dump more than once via hif_stop -> warm_reset ->
wait_for_target_init, possibly with different
values each.
Prevent this by doing the explicit fw register
dump only during power_up instead of
wait_for_target_init.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The duty cycle (% of quiet duration) is used to put the device
in quiet mode for the given period. Currently the quiet duration
is wrongly calculated which results in not enabling quiet mode.
Fix the calculation as below
duration = (period * duty cycle) / 100
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
New firmware revisions support beacon and probe
response templates instead. This means SWBA events
are no longer delivered for these firmware
revisions.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Along beacon template host is expected to setup
p2p information elements as well. Implement wmi
interface for it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
New firmware revisions with beacon templates need
probe templates as well because they don't forward
probe requests to host at all.
This is required for new firmware to work with
direct probe requests (notably required by hidden
ssid AP).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
New firmware revisions may support setting beacon
template. Implement wmi interface for it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This event is delivered to host by firmware if it
supports beacon templates only.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Because of wrong macro check in commit 96bba98393f9 ("ath10k: fix build error
when hwmon is off"), hwmon never be enabled. Fix that.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
When replenishing Rx buffers driver updates the address of the
buffer and the index of rx buffer in rx ring to the firmware.
Change in order by CPU can cause rx ring corruption. Add memory
barrier before updating rx buffer index to guarantee the order.
This could fix some instances of rx ring corruption due to done
bit in rx attention flag not set.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
wait_for_completion_timeout does not return negative values so the tests
for <= 0 are not needed and the case differentiation in the error handling
path unnecessary.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Recent commit
30c78167bc6536d9074aa79385a575596343bf69 ("ath10k:
set max_num_vdevs based on wmi op version")
skipped wmi-tlv case and left max_num_vdevs reset.
Make sure it is properly set.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
htt->max_throughput_mbps is not used anywhere.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This per-station debugfs entry helps to send delba in manual mode
for debugging purpose. It accepts tid, initiator and reason code
as inputs.
To send delba,
echo 0 1 37 >/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/delba
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This per-station debugfs entry helps to send addba response in
manual mode for debugging purpose. It accepts tid and status code
as input arguments.
To send addba response,
echo 0 25 >/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/addba_resp
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This per-station debugfs entry helps to send addba request in manual
mode. Need to pass two configuration parameters (tid, buffer size)
as input.
To send addba,
echo 1 32 >/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/addba
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add per station debugfs files when a station is added to mac80211's
station list. This helps to group peer specific debugfs entries
altogether. Right now this callback adds support to test aggregation
procedures (addba/addba_resp/delba) manually.
To enable automatic aggregation in target,
echo 0 >/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/aggr_mode
For manual mode,
echo 1 >/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/aggr_mode
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add WMI support for sending delba request. This command is used for
debugging purpose.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add WMI support for sending addba response manually. This command
is used for debugging purpose.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add WMI support for sending addba request. This command is meant
for debugging purpose.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add WMI support for clearing addba response before switching aggregation
mode (auto/manual) for debugging purpose.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This feature allows the FW to batch RX indications,
reducing the rate of host interrupt generation, which
in turn reduces CPU load. Currently, this is enabled
only for the 10.2 firmware.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
A value of zero indicates that 128B is the maximum
DMA request size for read/writes. But PCI cards based
on AR9880 can support 256B, so enable this for
the 10.2 firmware.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Major changes in ath10k:
* Device tree support
* Major restructuring how to handle different WMI interface versions
* Add WMI TLV interface in preparation for new firmware interface support
* Support new firmware branch 10.2.4
* Add thermal cooling interface
* Add hwmon interface to read temparture from the device
And of course lots of small fixes and cleanups.
|
|
kbuild reported a linking error:
ERROR: "devm_hwmon_device_register_with_groups"
[drivers/net/wireless/ath/ath10k/ath10k_core.ko] undefined!
Fix it by returning early and letting the compiler to optimise out the function
call.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Several of the drivers still were defining their own copies of various
macros. These are all moved into the core.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Convert driver to use routine rtl_dm_diginit().
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Convert driver rtl8723be to use routine rtl_dm_diginit().
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Convert driver rtl8723ae to use common routine rtl_dm_diginit().
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Convert driver rtl8192ee to use the common routine to initialize
dm_digtable.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch converts driver rtl8192de to use the common routine to
initialize dm_digtable.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
These changes convert both rtl8192ce and rtl8192cu to use the new routine.
Some additional definitions are needed in the core, thus several of the
headers for other drivers are affected, but no other executable code is
changed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The previous patch created a routine in rtlwifi to initialize dm_digtable.
Driver rtl8188ee is converted to use that routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Each of the drivers contains a routine that initializes the dm_digtable
member of the driver's private area. As a first step toward reducing the
size of the drivers, a copy of this driver is created in rtlwifi, and the
definitions of the parameters are moved there.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The description of the power-save variables for this driver is not as
clear as for the others. The wording is changed to match the others.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Some drivers refer to a particular quantity in the driver's private
are by one name, while others use a different name. These differences
are removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Instead of defining SDIO device identifier in brcm80211 code use
the defintions in linux/mmc/sdio_ids.h directly.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
After having all the dfs infrastructure in place, declare
radar_detect_widths support for the ap interfaces combination.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add dfs region to the reg domain channel update command.
Signed-off-by: Guy Mishol <guym@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since we are going to support dfs channels, there
is no reason to mark them as NO_IR (having
the DFS flag is enough anyway).
Additionally, when setting the regdomain configuration,
enable usable dfs channels.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
call wlcore_cmd_dfs_master_restart when starting
the ap on a new channel (after csa is done).
Add a new WLVIF_FLAG_BEACON_DISABLED flag to
indicate that dfs_master_restart command
is required.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
Michal Kazior
Rajkumar Manoharan
John W. Linville
Vasanthakumar Thiagarajan
Nicholas Mc Guire
Sujith Manoharan
Julia Lawall
Kalle Valo
Kalle Valo
Larry Finger
Arend van Spriel
Eliad Peller
Guy Mishol