| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
|
|
Pull timer updates from Thomas Gleixner:
"The truly boring timer and clocksource updates for 5.8:
- Not a single new clocksource or clockevent driver!
- Device tree updates for various chips
- Fixes and improvements and cleanups all over the place"
* tag 'timers-core-2020-06-02' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
dt-bindings: timer: Add renesas,em-sti bindings
clocksource/drivers/timer-versatile: Clear OF_POPULATED flag
clocksource: mips-gic-timer: Mark GIC timer as unstable if ref clock changes
clocksource: mips-gic-timer: Register as sched_clock
clocksource: dw_apb_timer_of: Fix missing clockevent timers
clocksource: dw_apb_timer: Affiliate of-based timer with any CPU
clocksource: dw_apb_timer: Make CPU-affiliation being optional
dt-bindings: timer: Move snps,dw-apb-timer DT schema from rtc
dt-bindings: rtc: Convert snps,dw-apb-timer to DT schema
clocksource/drivers/timer-ti-dm: Do one override clock parent in prepare()
clocksource/drivers/timer-ti-dm: Fix spelling mistake "detectt" -> "detect"
clocksource/drivers/timer-ti-dm: Fix warning for set but not used
clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support
clocksource/drivers/timer-ti-32k: Add support for initializing directly
drivers/clocksource/arm_arch_timer: Remove duplicate error message
clocksource/drivers/arc_timer: Remove duplicate error message
clocksource/drivers/rda: drop redundant Kconfig dependency
clocksource/drivers/timer-ti-dm: Fix warning for set but not used
clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support
clocksource/drivers/timer-ti-32k: Add support for initializing directly
...
|
|
Pull block driver updates from Jens Axboe:
"On top of the core changes, here are the block driver changes for this
merge window:
- NVMe changes:
- NVMe over Fibre Channel protocol updates, which also reach
over to drivers/scsi/lpfc (James Smart)
- namespace revalidation support on the target (Anthony
Iliopoulos)
- gcc zero length array fix (Arnd Bergmann)
- nvmet cleanups (Chaitanya Kulkarni)
- misc cleanups and fixes (me, Keith Busch, Sagi Grimberg)
- use a SRQ per completion vector (Max Gurtovoy)
- fix handling of runtime changes to the queue count (Weiping
Zhang)
- t10 protection information support for nvme-rdma and
nvmet-rdma (Israel Rukshin and Max Gurtovoy)
- target side AEN improvements (Chaitanya Kulkarni)
- various fixes and minor improvements all over, icluding the
nvme part of the lpfc driver"
- Floppy code cleanup series (Willy, Denis)
- Floppy contention fix (Jiri)
- Loop CONFIGURE support (Martijn)
- bcache fixes/improvements (Coly, Joe, Colin)
- q->queuedata cleanups (Christoph)
- Get rid of ioctl_by_bdev (Christoph, Stefan)
- md/raid5 allocation fixes (Coly)
- zero length array fixes (Gustavo)
- swim3 task state fix (Xu)"
* tag 'for-5.8/drivers-2020-06-01' of git://git.kernel.dk/linux-block: (166 commits)
bcache: configure the asynchronous registertion to be experimental
bcache: asynchronous devices registration
bcache: fix refcount underflow in bcache_device_free()
bcache: Convert pr_<level> uses to a more typical style
bcache: remove redundant variables i and n
lpfc: Fix return value in __lpfc_nvme_ls_abort
lpfc: fix axchg pointer reference after free and double frees
lpfc: Fix pointer checks and comments in LS receive refactoring
nvme: set dma alignment to qword
nvmet: cleanups the loop in nvmet_async_events_process
nvmet: fix memory leak when removing namespaces and controllers concurrently
nvmet-rdma: add metadata/T10-PI support
nvmet: add metadata support for block devices
nvmet: add metadata/T10-PI support
nvme: add Metadata Capabilities enumerations
nvmet: rename nvmet_check_data_len to nvmet_check_transfer_len
nvmet: rename nvmet_rw_len to nvmet_rw_data_len
nvmet: add metadata characteristics for a namespace
nvme-rdma: add metadata/T10-PI support
nvme-rdma: introduce nvme_rdma_sgl structure
...
|
|
Pull drm updates from Dave Airlie:
"Highlights:
- Core DRM had a lot of refactoring around managed drm resources to
make drivers simpler.
- Intel Tigerlake support is on by default
- amdgpu now support p2p PCI buffer sharing and encrypted GPU memory
Details:
core:
- uapi: error out EBUSY when existing master
- uapi: rework SET/DROP MASTER permission handling
- remove drm_pci.h
- drm_pci* are now legacy
- introduced managed DRM resources
- subclassing support for drm_framebuffer
- simple encoder helper
- edid improvements
- vblank + writeback documentation improved
- drm/mm - optimise tree searches
- port drivers to use devm_drm_dev_alloc
dma-buf:
- add flag for p2p buffer support
mst:
- ACT timeout improvements
- remove drm_dp_mst_has_audio
- don't use 2nd TX slot - spec recommends against it
bridge:
- dw-hdmi various improvements
- chrontel ch7033 support
- fix stack issues with old gcc
hdmi:
- add unpack function for drm infoframe
fbdev:
- misc fbdev driver fixes
i915:
- uapi: global sseu pinning
- uapi: OA buffer polling
- uapi: remove generated perf code
- uapi: per-engine default property values in sysfs
- Tigerlake GEN12 enabled.
- Lots of gem refactoring
- Tigerlake enablement patches
- move to drm_device logging
- Icelake gamma HW readout
- push MST link retrain to hotplug work
- bandwidth atomic helpers
- ICL fixes
- RPS/GT refactoring
- Cherryview full-ppgtt support
- i915 locking guidelines documented
- require linear fb stride to be 512 multiple on gen9
- Tigerlake SAGV support
amdgpu:
- uapi: encrypted GPU memory handling
- uapi: add MEM_SYNC IB flag
- p2p dma-buf support
- export VRAM dma-bufs
- FRU chip access support
- RAS/SR-IOV updates
- Powerplay locking fixes
- VCN DPG (powergating) enablement
- GFX10 clockgating fixes
- DC fixes
- GPU reset fixes
- navi SDMA fix
- expose FP16 for modesetting
- DP 1.4 compliance fixes
- gfx10 soft recovery
- Improved Critical Thermal Faults handling
- resizable BAR on gmc10
amdkfd:
- uapi: GWS resource management
- track GPU memory per process
- report PCI domain in topology
radeon:
- safe reg list generator fixes
nouveau:
- HD audio fixes on recent systems
- vGPU detection (fail probe if we're on one, for now)
- Interlaced mode fixes (mostly avoidance on Turing, which doesn't support it)
- SVM improvements/fixes
- NVIDIA format modifier support
- Misc other fixes.
adv7511:
- HDMI SPDIF support
ast:
- allocate crtc state size
- fix double assignment
- fix suspend
bochs:
- drop connector register
cirrus:
- move to tiny drivers.
exynos:
- fix imported dma-buf mapping
- enable runtime PM
- fixes and cleanups
mediatek:
- DPI pin mode swap
- config mipi_tx current/impedance
lima:
- devfreq + cooling device support
- task handling improvements
- runtime PM support
pl111:
- vexpress init improvements
- fix module auto-load
rcar-du:
- DT bindings conversion to YAML
- Planes zpos sanity check and fix
- MAINTAINERS entry for LVDS panel driver
mcde:
- fix return value
mgag200:
- use managed config init
stm:
- read endpoints from DT
vboxvideo:
- use PCI managed functions
- drop WC mtrr
vkms:
- enable cursor by default
rockchip:
- afbc support
virtio:
- various cleanups
qxl:
- fix cursor notify port
hisilicon:
- 128-byte stride alignment fix
sun4i:
- improved format handling"
* tag 'drm-next-2020-06-02' of git://anongit.freedesktop.org/drm/drm: (1401 commits)
drm/amd/display: Fix potential integer wraparound resulting in a hang
drm/amd/display: drop cursor position check in atomic test
drm/amdgpu: fix device attribute node create failed with multi gpu
drm/nouveau: use correct conflicting framebuffer API
drm/vblank: Fix -Wformat compile warnings on some arches
drm/amdgpu: Sync with VM root BO when switching VM to CPU update mode
drm/amd/display: Handle GPU reset for DC block
drm/amdgpu: add apu flags (v2)
drm/amd/powerpay: Disable gfxoff when setting manual mode on picasso and raven
drm/amdgpu: fix pm sysfs node handling (v2)
drm/amdgpu: move gpu_info parsing after common early init
drm/amdgpu: move discovery gfx config fetching
drm/nouveau/dispnv50: fix runtime pm imbalance on error
drm/nouveau: fix runtime pm imbalance on error
drm/nouveau: fix runtime pm imbalance on error
drm/nouveau/debugfs: fix runtime pm imbalance on error
drm/nouveau/nouveau/hmm: fix migrate zero page to GPU
drm/nouveau/nouveau/hmm: fix nouveau_dmem_chunk allocations
drm/nouveau/kms/nv50-: Share DP SST mode_valid() handling with MST
drm/nouveau/kms/nv50-: Move 8BPC limit for MST into nv50_mstc_get_modes()
...
|
|
Merge updates from Andrew Morton:
"A few little subsystems and a start of a lot of MM patches.
Subsystems affected by this patch series: squashfs, ocfs2, parisc,
vfs. With mm subsystems: slab-generic, slub, debug, pagecache, gup,
swap, memcg, pagemap, memory-failure, vmalloc, kasan"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (128 commits)
kasan: move kasan_report() into report.c
mm/mm_init.c: report kasan-tag information stored in page->flags
ubsan: entirely disable alignment checks under UBSAN_TRAP
kasan: fix clang compilation warning due to stack protector
x86/mm: remove vmalloc faulting
mm: remove vmalloc_sync_(un)mappings()
x86/mm/32: implement arch_sync_kernel_mappings()
x86/mm/64: implement arch_sync_kernel_mappings()
mm/ioremap: track which page-table levels were modified
mm/vmalloc: track which page-table levels were modified
mm: add functions to track page directory modifications
s390: use __vmalloc_node in stack_alloc
powerpc: use __vmalloc_node in alloc_vm_stack
arm64: use __vmalloc_node in arch_alloc_vmap_stack
mm: remove vmalloc_user_node_flags
mm: switch the test_vmalloc module to use __vmalloc_node
mm: remove __vmalloc_node_flags_caller
mm: remove both instances of __vmalloc_node_flags
mm: remove the prot argument to __vmalloc_node
mm: remove the pgprot argument to __vmalloc
...
|
|
Rename the Kconfig variable to clarify the scope.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
Cc: Gao Xiang <xiang@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Kelley <mikelley@microsoft.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Wei Liu <wei.liu@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mackerras <paulus@ozlabs.org>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Will Deacon <will@kernel.org>
Link: http://lkml.kernel.org/r/20200414131348.444715-11-hch@lst.de
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull vfs updates from Al Viro:
"Assorted patches from Miklos.
An interesting part here is /proc/mounts stuff..."
The "/proc/mounts stuff" is using a cursor for keeeping the location
data while traversing the mount listing.
Also probably worth noting is the addition of faccessat2(), which takes
an additional set of flags to specify how the lookup is done
(AT_EACCESS, AT_SYMLINK_NOFOLLOW, AT_EMPTY_PATH).
* 'from-miklos' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vfs: add faccessat2 syscall
vfs: don't parse "silent" option
vfs: don't parse "posixacl" option
vfs: don't parse forbidden flags
statx: add mount_root
statx: add mount ID
statx: don't clear STATX_ATIME on SB_RDONLY
uapi: deprecate STATX_ALL
utimensat: AT_EMPTY_PATH support
vfs: split out access_override_creds()
proc/mounts: add cursor
aio: fix async fsync creds
vfs: allow unprivileged whiteout creation
|
|
Pull uaccess/csum updates from Al Viro:
"Regularize the sitation with uaccess checksum primitives:
- fold csum_partial_... into csum_and_copy_..._user()
- on x86 collapse several access_ok()/stac()/clac() into
user_access_begin()/user_access_end()"
* 'uaccess.csum' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
default csum_and_copy_to_user(): don't bother with access_ok()
take the dummy csum_and_copy_from_user() into net/checksum.h
arm: switch to csum_and_copy_from_user()
sh32: convert to csum_and_copy_from_user()
m68k: convert to csum_and_copy_from_user()
xtensa: switch to providing csum_and_copy_from_user()
sparc: switch to providing csum_and_copy_from_user()
parisc: turn csum_partial_copy_from_user() into csum_and_copy_from_user()
alpha: turn csum_partial_copy_from_user() into csum_and_copy_from_user()
ia64: turn csum_partial_copy_from_user() into csum_and_copy_from_user()
ia64: csum_partial_copy_nocheck(): don't abuse csum_partial_copy_from_user()
x86: switch 32bit csum_and_copy_to_user() to user_access_{begin,end}()
x86: switch both 32bit and 64bit to providing csum_and_copy_from_user()
x86_64: csum_..._copy_..._user(): switch to unsafe_..._user()
get rid of csum_partial_copy_to_user()
|
|
Pull ARM updates from Russell King:
- remove a now unnecessary usage of the KERNEL_DS for
sys_oabi_epoll_ctl()
- update my email address in a number of drivers
- decompressor EFI updates from Ard Biesheuvel
- module unwind section handling updates
- sparsemem Kconfig cleanups
- make act_mm macro respect THREAD_SIZE
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8980/1: Allow either FLATMEM or SPARSEMEM on the multiplatform build
ARM: 8979/1: Remove redundant ARCH_SPARSEMEM_DEFAULT setting
ARM: 8978/1: mm: make act_mm() respect THREAD_SIZE
ARM: decompressor: run decompressor in place if loaded via UEFI
ARM: decompressor: move GOT into .data for EFI enabled builds
ARM: decompressor: defer loading of the contents of the LC0 structure
ARM: decompressor: split off _edata and stack base into separate object
ARM: decompressor: move headroom variable out of LC0
ARM: 8976/1: module: allow arch overrides for .init section names
ARM: 8975/1: module: fix handling of unwind init sections
ARM: 8974/1: use SPARSMEM_STATIC when SPARSEMEM is enabled
ARM: 8971/1: replace the sole use of a symbol with its definition
ARM: 8969/1: decompressor: simplify libfdt builds
Update rmk's email address in various drivers
ARM: compat: remove KERNEL_DS usage in sys_oabi_epoll_ctl()
|
|
Pull EFI updates from Ingo Molnar:
"The EFI changes for this cycle are:
- preliminary changes for RISC-V
- Add support for setting the resolution on the EFI framebuffer
- Simplify kernel image loading for arm64
- Move .bss into .data via the linker script instead of relying on
symbol annotations.
- Get rid of __pure getters to access global variables
- Clean up the config table matching arrays
- Rename pr_efi/pr_efi_err to efi_info/efi_err, and use them
consistently
- Simplify and unify initrd loading
- Parse the builtin command line on x86 (if provided)
- Implement printk() support, including support for wide character
strings
- Simplify GDT handling in early mixed mode thunking code
- Some other minor fixes and cleanups"
* tag 'efi-core-2020-06-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (79 commits)
efi/x86: Don't blow away existing initrd
efi/x86: Drop the special GDT for the EFI thunk
efi/libstub: Add missing prototype for PE/COFF entry point
efi/efivars: Add missing kobject_put() in sysfs entry creation error path
efi/libstub: Use pool allocation for the command line
efi/libstub: Don't parse overlong command lines
efi/libstub: Use snprintf with %ls to convert the command line
efi/libstub: Get the exact UTF-8 length
efi/libstub: Use %ls for filename
efi/libstub: Add UTF-8 decoding to efi_puts
efi/printf: Add support for wchar_t (UTF-16)
efi/gop: Add an option to list out the available GOP modes
efi/libstub: Add definitions for console input and events
efi/libstub: Implement printk-style logging
efi/printf: Turn vsprintf into vsnprintf
efi/printf: Abort on invalid format
efi/printf: Refactor code to consolidate padding and output
efi/printf: Handle null string input
efi/printf: Factor out integer argument retrieval
efi/printf: Factor out width/precision parsing
...
|
|
Pull crypto updates from Herbert Xu:
"API:
- Introduce crypto_shash_tfm_digest() and use it wherever possible.
- Fix use-after-free and race in crypto_spawn_alg.
- Add support for parallel and batch requests to crypto_engine.
Algorithms:
- Update jitter RNG for SP800-90B compliance.
- Always use jitter RNG as seed in drbg.
Drivers:
- Add Arm CryptoCell driver cctrng.
- Add support for SEV-ES to the PSP driver in ccp"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (114 commits)
crypto: hisilicon - fix driver compatibility issue with different versions of devices
crypto: engine - do not requeue in case of fatal error
crypto: cavium/nitrox - Fix a typo in a comment
crypto: hisilicon/qm - change debugfs file name from qm_regs to regs
crypto: hisilicon/qm - add DebugFS for xQC and xQE dump
crypto: hisilicon/zip - add debugfs for Hisilicon ZIP
crypto: hisilicon/hpre - add debugfs for Hisilicon HPRE
crypto: hisilicon/sec2 - add debugfs for Hisilicon SEC
crypto: hisilicon/qm - add debugfs to the QM state machine
crypto: hisilicon/qm - add debugfs for QM
crypto: stm32/crc32 - protect from concurrent accesses
crypto: stm32/crc32 - don't sleep in runtime pm
crypto: stm32/crc32 - fix multi-instance
crypto: stm32/crc32 - fix run-time self test issue.
crypto: stm32/crc32 - fix ext4 chksum BUG_ON()
crypto: hisilicon/zip - Use temporary sqe when doing work
crypto: hisilicon - add device error report through abnormal irq
crypto: hisilicon - remove codes of directly report device errors through MSI
crypto: hisilicon - QM memory management optimization
crypto: hisilicon - unify initial value assignment into QM
...
|
|
xdp_umem.c had overlapping changes between the 64-bit math fix
for the calculation of npgs and the removal of the zerocopy
memory type which got rid of the chunk_size_nohdr member.
The mlx5 Kconfig conflict is a case where we just take the
net-next copy of the Kconfig entry dependency as it takes on
the ESWITCH dependency by one level of indirection which is
what the 'net' conflicting change is trying to ensure.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull ARM SoC fixes from Arnd Bergmann:
"This time there is one fix for the error path in the mediatek cmdq
driver (used by their video driver) and a couple of devicetree fixes,
mostly for 32-bit ARM, and fairly harmless:
- On OMAP2 there were a few regressions in the ethernet drivers, one
of them leading to an external abort trap
- One Raspberry Pi version had a misconfigured LED
- Interrupts on Broadcom NSP were slightly misconfigured
- One i.MX6q board had issues with graphics mode setting
- On mmp3 there are some minor fixes that were submitted for v5.8
with a cc:stable tag, so I ended up picking them up here as well
- The Mediatek Video Codec needs to run at a higher frequency than
configured originally"
* tag 'armsoc-fixes-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: dts: mmp3: Drop usb-nop-xceiv from HSIC phy
ARM: dts: mmp3-dell-ariel: Fix the SPI devices
ARM: dts: mmp3: Use the MMP3 compatible string for /clocks
ARM: dts: bcm: HR2: Fix PPI interrupt types
ARM: dts: bcm2835-rpi-zero-w: Fix led polarity
ARM: dts/imx6q-bx50v3: Set display interface clock parents
soc: mediatek: cmdq: return send msg error code
arm64: dts: mt8173: fix vcodec-enc clock
ARM: dts: Fix wrong mdio clock for dm814x
ARM: dts: am437x: fix networking on boards with ksz9031 phy
ARM: dts: am57xx: fix networking on boards with ksz9031 phy
|
|
Note that csum_partial_copy_from_user() is in assembler here,
so I'm leaving it alone and just providing the wrapper for
it. When/if we go for switching arm to user_access_{begin,end}()
(doing domain switches in those), somebody well need to look
into that one.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Enable ethernet wake-on-lan feature for imx6q/dl/qp sabresd
boards since the PHY clock is supplied by external osc.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- Update the imx6qdl gpr property to define gpr register
offset and bit in DT.
- Add imx6sx/imx6ul/imx7d ethernet stop mode property.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ARMv7 chips with LPAE can often benefit from SPARSEMEM, as portions of
system memory can be located deep in the 36-bit address space. Allow
FLATMEM or SPARSEMEM to be selectable at compile time; FLATMEM remains
the default.
This is based on Kevin's "[PATCH 3/3] ARM: Allow either FLATMEM or
SPARSEMEM on the multi-v7 build" from [1] and shamelessly rips off his
commit message text above. As Arnd pointed out at [2] there doesn't
seem to be any reason to tie this specifically to ARMv7, so this has
been changed to apply to all multiplatform kernels.
The addition of this option does not change the defaults and a build with
any defconfig will behave the same way as previously.
The only effect this change has is to enable user to change "Memory model"
selection in interactive kernel configuration (menuconfig, xconfig etc).
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2014-September/286837.html
[2] http://lists.infradead.org/pipermail/linux-arm-kernel/2014-October/298950.html
[ rppt: added ARCH_SELECT_MEMORY_MODEL and updated the changelog ]
Cc: Kevin Cernekee <cernekee@gmail.com>
Tested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Mike Rapoport <mike.rapoport@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
If ARCH_SPARSEMEM_ENABLE=y and ARCH_{FLATMEM,DISCONTIGMEM}_ENABLE=n,
then the logic in mm/Kconfig already makes CONFIG_SPARSEMEM the only
choice. This is true for all of the existing ARM users of
ARCH_SPARSEMEM_ENABLE.
Forcing ARCH_SPARSEMEM_DEFAULT=y if ARCH_SPARSEMEM_ENABLE=y prevents
us from ever defaulting to FLATMEM, so we should remove this setting.
Link: https://lkml.org/lkml/2015/6/4/757
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Tested-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Mike Rapoport <mike.rapoport@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Recent work with KASan exposed the folling hard-coded bitmask
in arch/arm/mm/proc-macros.S:
bic rd, sp, #8128
bic rd, rd, #63
This forms the bitmask 0x1FFF that is coinciding with
(PAGE_SIZE << THREAD_SIZE_ORDER) - 1, this code was assuming
that THREAD_SIZE is always 8K (8192).
As KASan was increasing THREAD_SIZE_ORDER to 2, I ran into
this bug.
Fix it by this little oneline suggested by Ard:
bic rd, sp, #(THREAD_SIZE - 1) & ~63
Where THREAD_SIZE is defined using THREAD_SIZE_ORDER.
We have to also include <linux/const.h> since the THREAD_SIZE
expands to use the _AC() macro.
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Suggested-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Simplify EFI handover to decompressor
The EFI stub in the ARM kernel runs in the context of the firmware, which
means it usually runs with the caches and MMU on. Currently, we relocate
the zImage so it appears in the first 128 MiB, disable the MMU and caches
and invoke the decompressor via its ordinary entry point. However, since we
can pass the base of DRAM directly, there is no need to relocate the zImage,
which also means there is no need to disable and re-enable the caches and
create new page tables etc.
This also allows systems whose DRAM start address is not a round multiple
of 128 MB to decompress the kernel proper to the base of memory, ensuring
that all memory is usable at runtime.
|
|
Pull ARM fixes from Russell King:
- correct value of decompressor tag size in header
- fix DACR value when we have nested exceptions
- fix a missing newline on a kernel message
- fix mask for ptrace thumb breakpoint hook
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8977/1: ptrace: Fix mask for thumb breakpoint hook
ARM: 8973/1: Add missing newline terminator to kernel message
ARM: uaccess: fix DACR mismatch with nested exceptions
ARM: uaccess: integrate uaccess_save and uaccess_restore
ARM: uaccess: consolidate uaccess asm to asm/uaccess-asm.h
ARM: 8970/1: decompressor: increase tag size
|
|
Few cpsw related dts fixes for omaps
Recent cpsw driver changes exposed few regressions in the cpsw related
dts configuration that would be good to fix:
- Few more boards still need to be updated to use rgmii-rxid phy caused
by the fallout from commit bcf3440c6dd7 ("net: phy: micrel: add phy-mode
support for the KSZ9031 PHY" as the rx delay is now disabled unless we
use rgmii-rxid.
- On dm814x we have been using a wrong clock for mdio that now can produce
external abort on some boards
* tag 'omap-for-v5.7/cpsw-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix wrong mdio clock for dm814x
ARM: dts: am437x: fix networking on boards with ksz9031 phy
ARM: dts: am57xx: fix networking on boards with ksz9031 phy
Link: https://lore.kernel.org/r/pull-1589472123-367692@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
More EFI changes for v5.8:
- Rename pr_efi/pr_efi_err to efi_info/efi_err, and use them consistently
- Simplify and unify initrd loading
- Parse the builtin command line on x86 (if provided)
- Implement printk() support, including support for wide character strings
- Some fixes for issues introduced by the first batch of v5.8 changes
- Fix a missing prototypes warning
- Simplify GDT handling in early mixed mode thunking code
- Some other minor fixes and cleanups
Conflicts:
drivers/firmware/efi/libstub/efistub.h
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
5.7, please pull the following:
- Vincent fixes the polarity of the ACT LED on the Raspberry Pi Zero W
board
- Hamish fixes the ARM PPI interrupts sensitivy for the Hurricane 2
SoCs
* tag 'arm-soc/for-5.7/devicetree-fixes-part2-v2' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm: HR2: Fix PPI interrupt types
ARM: dts: bcm2835-rpi-zero-w: Fix led polarity
Link: https://lore.kernel.org/r/20200524203714.17035-1-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a missing prototype warning by adding a forward declaration
for the PE/COFF entrypoint, and while at it, align the function
name between the x86 and ARM versions of the stub.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
i.MX fixes for 5.7, round 2:
One imx6q-bx50v3 device tree change to fix an issue, attempting atomic
modeset while using HDMI and display port at the same time causes LDB
clock programming to destroy the programming of HDMI.
* tag 'imx-fixes-5.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts/imx6q-bx50v3: Set display interface clock parents
Link: https://lore.kernel.org/r/20200521150719.GB24084@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
These three fixes should make it into linux-5.7 and
also into the branch for other mmp dt changes for v5.8,
so I created a branch for them.
* mmp/fixes:
ARM: dts: mmp3: Drop usb-nop-xceiv from HSIC phy
ARM: dts: mmp3-dell-ariel: Fix the SPI devices
ARM: dts: mmp3: Use the MMP3 compatible string for /clocks
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
"usb-nop-xceiv" is good enough if we don't lose the configuration done
by the firmware, but we'd really prefer a real driver.
Unfortunately, the PHY core is odd in that when the node is compatible
with "usb-nop-xceiv", it ignores the other compatible strings. Let's
just remove it.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
I've managed to get about everything wrong while digging these out of
OEM's board file.
Correct the bus numbers, the exact model of the NOR flash, polarity of
the chip selects and align the SPI frequency with the data sheet.
Tested that it works now, with a slight fix to the PXA SSP driver.
Link: https://lore.kernel.org/r/20200419171157.672999-16-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Clocks are in fact slightly different on MMP3. In particular, PLL2 is
fixed to a different frequency, there's an extra PLL3, and the GPU
clocks are configured differently.
Link: https://lore.kernel.org/r/20200419171157.672999-15-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
These error messages are output when booting on a BCM HR2 system:
GIC: PPI11 is secure or misconfigured
GIC: PPI13 is secure or misconfigured
Per ARM documentation these interrupts are triggered on a rising edge.
See ARM Cortex A-9 MPCore Technical Reference Manual, Revision r4p1,
Section 3.3.8 Interrupt Configuration Registers.
The same issue was resolved for NSP systems in commit 5f1aa51c7a1e
("ARM: dts: NSP: Fix PPI interrupt types").
Fixes: b9099ec754b5 ("ARM: dts: Add Broadcom Hurricane 2 DTS include file")
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
The status "ACT" led on the Raspberry Pi Zero W is on when GPIO 47 is low.
This has been verified on a board and somewhat confirmed by both the GPIO
name ("STATUS_LED_N") and the reduced schematics [1].
[1]: https://www.raspberrypi.org/documentation/hardware/raspberrypi/schematics/rpi_SCH_ZeroW_1p1_reduced.pdf
Fixes: 2c7c040c73e9 ("ARM: dts: bcm2835: Add Raspberry Pi Zero W")
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Avoid LDB and IPU DI clocks both using the same parent. LDB requires
pasthrough clock to avoid breaking timing while IPU DI does not.
Force IPU DI clocks to use IMX6QDL_CLK_PLL2_PFD0_352M as parent
and LDB to use IMX6QDL_CLK_PLL5_VIDEO_DIV.
This fixes an issue where attempting atomic modeset while using
HDMI and display port at the same time causes LDB clock programming
to destroy the programming of HDMI that was done during the same
modeset.
Cc: stable@vger.kernel.org
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
[Use IMX6QDL_CLK_PLL2_PFD0_352M instead of IMX6QDL_CLK_PLL2_PFD2_396M
originally chosen by Robert Beckett to avoid affecting eMMC clock
by DRM atomic updates]
Signed-off-by: Ian Ray <ian.ray@ge.com>
[Squash Robert's and Ian's commits for bisectability, update patch
description and add stable tag]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The decompressor can load from anywhere in memory, and the only reason
the EFI stub code relocates it is to ensure it appears within the first
128 MiB of memory, so that the uncompressed kernel ends up at the right
offset in memory.
We can short circuit this, and simply jump into the decompressor startup
code at the point where it knows where the base of memory lives. This
also means there is no need to disable the MMU and caches, create new
page tables and re-enable them.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
|
|
We will be running the decompressor in place after a future patch,
instead of copying it around first. This means we no longer have to
disable and re-enable the MMU and caches either. However, this means
we will be loaded with the restricted permissions set by the UEFI
firmware, which means that we have to move the GOT table into the
data section in order for the contents to be writable by the code
itself.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
|
|
The remaining contents of LC0 are only used after the point in the
decompressor startup code where we enter via 'wont_overwrite'. So
move the loading of the LC0 structure after it. This will allow us
to jump to wont_overwrite directly from the EFI stub, and execute
the decompressor in place at the offset it was loaded by the UEFI
firmware.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
|
|
In preparation of moving the handling of the LC0 object to a later stage
in the decompressor startup code, move out _edata and the initial value
of the stack pointer, which are needed earlier than the remaining
contents of LC0.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
|
|
Before breaking up LC0 into different pieces, move out the variable
that is already place-relative (given that it subtracts 'restart' in
the expression) and so its value does not need to be added to the
runtime address of the LC0 symbol itself.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
|
|
Unwind information for init sections is placed in .ARM.exidx.init.text
and .ARM.extab.init.text. The module core doesn't know that these are
init sections so they are allocated along with the core sections, and if
the core and init sections get allocated in different memory regions
(which is possible with CONFIG_ARM_MODULE_PLTS=y) and they can't reach
each other, relocation fails:
final section addresses:
...
0x7f800000 .init.text
..
0xcbb54078 .ARM.exidx.init.text
..
section 16 reloc 0 sym '': relocation 42 out of range (0xcbb54078 ->
0x7f800000)
Fix this by informing the module core that these sections are init
sections, and by removing the init unwind tables before the module core
frees the init sections.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
call_undef_hook() in traps.c applies the same instr_mask for both 16-bit
and 32-bit thumb instructions. If instr_mask then is only 16 bits wide
(0xffff as opposed to 0xffffffff), the first half-word of 32-bit thumb
instructions will be masked out. This makes the function match 32-bit
thumb instructions where the second half-word is equal to instr_val,
regardless of the first half-word.
The result in this case is that all undefined 32-bit thumb instructions
with the second half-word equal to 0xde01 (udf #1) work as breakpoints
and will raise a SIGTRAP instead of a SIGILL, instead of just the one
intended 16-bit instruction. An example of such an instruction is
0xeaa0de01, which is unallocated according to Arm ARM and should raise a
SIGILL, but instead raises a SIGTRAP.
This patch fixes the issue by setting all the bits in instr_mask, which
will still match the intended 16-bit thumb instruction (where the
upper half is always 0), but not any 32-bit thumb instructions.
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Fredrik Strupe <fredrik@strupe.net>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
The commit 3e347261a80b5 ("[PATCH] sparsemem extreme implementation")
made SPARSMEM_EXTREME the default option for configurations that enable
SPARSEMEM.
For ARM systems with handful of memory banks SPARSEMEM_EXTREME is an
overkill.
Ensure that SPARSMEM_STATIC is enabled in the configurations that use
SPARSEMEM.
Fixes: 3e347261a80b5 ("[PATCH] sparsemem extreme implementation")
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Pull ARM SoC/dt fixes from Arnd Bergmann:
"This round of fixes is almost exclusively device tree changes, with
trivial defconfig fixes and one compiler warning fix added in.
A number of patches are to fix dtc warnings, in particular on Amlogic,
i.MX and Rockchips.
Other notable changes include:
Renesas:
- Fix a wrong clock configuration on R-Mobile A1
- Fix IOMMU support on R-Car V3H
Allwinner
- Multiple audio fixes
Qualcomm
- Use a safe CPU voltage on MSM8996
- Fixes to match a late audio driver change
Rockchip:
- Some fixes for the newly added Pinebook Pro
NXP i.MX:
- Fix I2C1 pinctrl configuration for i.MX27 phytec-phycard board
- Fix imx6dl-yapp4-ursa board Ethernet connection
OMAP:
- A regression fix for non-existing can device on am534x-idk
- Fix flakey wlan on droid4 where some devices would not connect at
all because of internal pull being used with an external pull
- Fix occasional missed wake-up events on droid4 modem uart"
* tag 'arm-soc-fixes-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (51 commits)
ARM: dts: iwg20d-q7-dbcm-ca: Remove unneeded properties in hdmi@39
ARM: dts: renesas: Make hdmi encoder nodes compliant with DT bindings
arm64: dts: renesas: Make hdmi encoder nodes compliant with DT bindings
arm64: defconfig: add MEDIA_PLATFORM_SUPPORT
arm64: defconfig: ARCH_R8A7795: follow changed config symbol name
arm64: defconfig: add DRM_DISPLAY_CONNECTOR
arm64: defconfig: DRM_DUMB_VGA_DAC: follow changed config symbol name
ARM: oxnas: make ox820_boot_secondary static
ARM: dts: r8a7740: Add missing extal2 to CPG node
ARM: dts: omap4-droid4: Fix occasional lost wakeirq for uart1
ARM: dts: omap4-droid4: Fix flakey wlan by disabling internal pull for gpio
arm64: dts: allwinner: a64: Remove unused SPDIF sound card
arm64: dts: allwinner: a64: pinetab: Fix cpvdd supply name
arm64: dts: meson-g12: remove spurious blank line
arm64: dts: meson-g12b-khadas-vim3: add missing frddr_a status property
arm64: dts: meson-g12-common: fix dwc2 clock names
arm64: dts: meson-g12b-ugoos-am6: fix usb vbus-supply
arm64: dts: freescale: imx8mp: update input_val for AUDIOMIX_BIT_STREAM
ARM: dts: r7s9210: Remove bogus clock-names from OSTM nodes
ARM: dts: rockchip: fix pinctrl sub nodename for spi in rk322x.dtsi
...
|
|
Renesas fixes for v5.7 (take two)
- Fix a wrong clock configuration on R-Mobile A1,
- Minor fixes that are fast-tracked to avoid introducing regressions
during conversion of DT bindings to json-schema.
* tag 'renesas-fixes-for-v5.7-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
ARM: dts: iwg20d-q7-dbcm-ca: Remove unneeded properties in hdmi@39
ARM: dts: renesas: Make hdmi encoder nodes compliant with DT bindings
arm64: dts: renesas: Make hdmi encoder nodes compliant with DT bindings
ARM: dts: r8a7740: Add missing extal2 to CPG node
Link: https://lore.kernel.org/r/20200515125043.22811-1-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Move the bpf verifier trace check into the new switch statement in
HEAD.
Resolve the overlapping changes in hinic, where bug fixes overlap
the addition of VF support.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Fix sk_psock reference count leak on receive, from Xiyu Yang.
2) CONFIG_HNS should be invisible, from Geert Uytterhoeven.
3) Don't allow locking route MTUs in ipv6, RFCs actually forbid this,
from Maciej Żenczykowski.
4) ipv4 route redirect backoff wasn't actually enforced, from Paolo
Abeni.
5) Fix netprio cgroup v2 leak, from Zefan Li.
6) Fix infinite loop on rmmod in conntrack, from Florian Westphal.
7) Fix tcp SO_RCVLOWAT hangs, from Eric Dumazet.
8) Various bpf probe handling fixes, from Daniel Borkmann.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (68 commits)
selftests: mptcp: pm: rm the right tmp file
dpaa2-eth: properly handle buffer size restrictions
bpf: Restrict bpf_trace_printk()'s %s usage and add %pks, %pus specifier
bpf: Add bpf_probe_read_{user, kernel}_str() to do_refine_retval_range
bpf: Restrict bpf_probe_read{, str}() only to archs where they work
MAINTAINERS: Mark networking drivers as Maintained.
ipmr: Add lockdep expression to ipmr_for_each_table macro
ipmr: Fix RCU list debugging warning
drivers: net: hamradio: Fix suspicious RCU usage warning in bpqether.c
net: phy: broadcom: fix BCM54XX_SHD_SCR3_TRDDAPD value for BCM54810
tcp: fix error recovery in tcp_zerocopy_receive()
MAINTAINERS: Add Jakub to networking drivers.
MAINTAINERS: another add of Karsten Graul for S390 networking
drivers: ipa: fix typos for ipa_smp2p structure doc
pppoe: only process PADT targeted at local interfaces
selftests/bpf: Enforce returning 0 for fentry/fexit programs
bpf: Enforce returning 0 for fentry/fexit progs
net: stmmac: fix num_por initialization
security: Fix the default value of secid_to_secctx hook
libbpf: Fix register naming in PT_REGS s390 macros
...
|
|
Given the legacy bpf_probe_read{,str}() BPF helpers are broken on archs
with overlapping address ranges, we should really take the next step to
disable them from BPF use there.
To generally fix the situation, we've recently added new helper variants
bpf_probe_read_{user,kernel}() and bpf_probe_read_{user,kernel}_str().
For details on them, see 6ae08ae3dea2 ("bpf: Add probe_read_{user, kernel}
and probe_read_{user,kernel}_str helpers").
Given bpf_probe_read{,str}() have been around for ~5 years by now, there
are plenty of users at least on x86 still relying on them today, so we
cannot remove them entirely w/o breaking the BPF tracing ecosystem.
However, their use should be restricted to archs with non-overlapping
address ranges where they are working in their current form. Therefore,
move this behind a CONFIG_ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE and
have x86, arm64, arm select it (other archs supporting it can follow-up
on it as well).
For the remaining archs, they can workaround easily by relying on the
feature probe from bpftool which spills out defines that can be used out
of BPF C code to implement the drop-in replacement for old/new kernels
via: bpftool feature probe macro
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Cc: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/bpf/20200515101118.6508-2-daniel@iogearbox.net
|
|
Remove the adi,input-style and adi,input-justification properties of
hdmi@39 to make it compliant with the "adi,adv7511w" DT binding.
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200511110611.3142-6-ricardo.canuelo@collabora.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Small fixes to make these DTs compliant with the adi,adv7511w and
adi,adv7513 bindings:
r8a7745-iwg22d-sodimm-dbhd-ca.dts
r8a7790-lager.dts
r8a7790-stout.dts
r8a7791-koelsch.dts
r8a7791-porter.dts
r8a7792-blanche.dts
r8a7793-gose.dts
r8a7794-silk.dts:
Remove the adi,input-style and adi,input-justification properties.
r8a7792-wheat.dts:
Reorder the I2C slave addresses of hdmi@3d and hdmi@39 and remove
the adi,input-style and adi,input-justification properties.
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200511110611.3142-3-ricardo.canuelo@collabora.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
Linus Torvalds
Christoph Hellwig
David S. Miller
Al Viro
Fugang Duan
Gregory Fong
Kevin Cernekee
Linus Walleij
Russell King
Arnd Bergmann
Ingo Molnar
Ard Biesheuvel
Lubomir Rintel
Hamish Martin
Vincent Stehlé
Robert Beckett
Vincent Whitchurch
Fredrik Strupe
Mike Rapoport
Daniel Borkmann
Ricardo Cañuelo