| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
aml_download_firmware() reads two lengths from the firmware header and
uses them to build pointers before checking that the header and segment
data are present. A truncated or inconsistent firmware image can make
the driver read past firmware->data while constructing TCI commands.
Reject images shorter than the header and ensure that the ICCM and DCCM
ranges fit within the loaded firmware before downloading either segment.
Fixes: 37bac77e4649 ("Bluetooth: hci_uart: Add support for Amlogic HCI UART")
Cc: stable@vger.kernel.org
Signed-off-by: Laxman Acharya Padhya <acharyalaxman8848@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
BRDS revision 2 introduces per-chain (Chain A and Chain B) TX power
limits across five sub-bands (2.4G, 5.2G, 5.8/5.9G, 6G-low, 6G-high),
replacing the single-chain per-modulation model of revisions 0 and 1.
- Add btintel_set_sar_rev2() which sends the full Rev2 DDC sequence:
0x019e inc-power-mode enable flag (1 byte)
0x0311 2.4 GHz sub-band limits (2 bytes)
0x0312 5.2 GHz sub-band limits (2 bytes)
0x0313 5.8/5.9 GHz sub-band limits (2 bytes)
0x0314 5.8/5.9 GHz sub-band limits again (2 bytes, duplicate FW reg)
0x0315 6 GHz low sub-band limits (2 bytes)
0x0316 6 GHz high sub-band limits (2 bytes)
followed by the SAR-init-complete command (0xfe25).
logs from dmesg when BTSAR2 is enabled in Coreboot/BIOS:
Bluetooth: hci0: BT SAR Rev2: revision=2 bt_sar_bios=1 inc_power_mode=1
Bluetooth: hci0: BT SAR Rev2 Chain A: 2g4=76 5g2=0 5g8_5g9=0 6g1=0 6g3=0
Bluetooth: hci0: BT SAR Rev2 Chain B: 2g4=102 5g2=0 5g8_5g9=0 6g1=0 6g3=0
Signed-off-by: Ravindra <ravindra@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add a read-write sysfs entry at /sys/bus/pci/devices/<BDF>/vendor_reset
to allow userspace to trigger PLDR (Product Level Device Reset).
Reading the attribute displays supported reset types. Writing
integer 0 triggers PLDR. Any other input is rejected with
-EINVAL and a warning log.
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This module sets the acpi_device_id::driver_data to 0 but
the field is not actually used within the module, we can
just drop it from the table.
While we are at it - use a named initializer for the
acpi_device_id::id field and drop setting the list
terminator fields explicitly as well.
Signed-off-by: Pawel Zalewski (The Capable Hub) <pzalewski@thegoodpenguin.co.uk>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Use a named initializer for the acpi_device_id fields which
makes the code more readable and consistent with how lists
are initialized in the rest of the kernel code base.
While we are at it - unify the list terminator to have
a single space between the brackets without a trailing
coma.
Signed-off-by: Pawel Zalewski (The Capable Hub) <pzalewski@thegoodpenguin.co.uk>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
For a HCI_VENDOR_PKT frame, hci_recv_frame() does not accept it and
will kfree_skb() it directly.
But btmrvl_sdio_card_to_host() is still calling hci_recv_frame() for
the frame.
Fix by freeing it with kfree_skb() directly.
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Simplify btintel_classify_pkt_type() by using hci_acl_handle() instead of:
__u16 handle = __le16_to_cpu(hci_acl_hdr(skb)->handle);
... hci_handle(handle) ...
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Simplify btusb_recv_bulk() by using hci_acl_dlen() instead of:
__le16 dlen = hci_acl_hdr(skb)->dlen;
... __le16_to_cpu(dlen) ...
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add btusb_prepare_reset() to do cleanup before a reset, and
apply it to btusb_mtk_reset() as well.
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Both helpers currently take struct btusb_data *, which is private to
btusb.c, as parameter type as below:
int btusb_recv_event(struct btusb_data *data, struct sk_buff *skb)
int btusb_recv_acl(struct btusb_data *data, struct sk_buff *skb)
To allow vendor USB-transport-specific source files to share them as
well, change the type to struct hci_dev *.
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
In rsi_hci_attach(), ops->set_bt_context() stores the newly allocated
h_adapter into common->bt_adapter before hci_alloc_dev() and
hci_register_dev() are called. If either of these fails, h_adapter
is freed but common->bt_adapter remains a non-NULL dangling pointer.
This causes a deterministically reachable use-after-free when the
device operates in a BT+WiFi coexistence mode and CONFIG_RSI_COEX
is enabled. The following software-only trigger paths exist:
1. SDIO driver .remove (rsi_disconnect)
2. USB driver .disconnect (rsi_disconnect)
3. SDIO driver .shutdown (rsi_shutdown)
4. Hibernation .freeze (rsi_freeze)
All four paths check:
if (IS_ENABLED(CONFIG_RSI_COEX) && coex_mode > 1 && bt_adapter)
rsi_bt_ops.detach(bt_adapter); // use-after-free
coex_mode is set during rsi_91x_init(), before rsi_hci_attach() is
called, and is not cleared on attach failure. Since set_bt_context()
already wrote bt_adapter before the failure, the deinit paths see a
non-NULL dangling pointer and proceed to detach it.
Fix this by moving set_bt_context() after hci_register_dev() succeeds.
On failure paths bt_adapter stays NULL, and the deinit callers correctly
skip the detach call.
Signed-off-by: Chen Changcheng <chenchangcheng@kylinos.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
In the switch-case block for hardware variant detection, the
default case has an unreachable 'break' statement following
'goto exit_error'. Remove the dead code.
Signed-off-by: Chen Changcheng <chenchangcheng@kylinos.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The macros below have different meanings even though they share the
same value 0xff:
HCI_VENDOR_PKT: HCI packet indicator or type
HCI_EV_VENDOR: event code of a VSE
This usage of HCI_VENDOR_PKT is wrongly checking an event code.
Fix by using HCI_EV_VENDOR for event code.
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The macros below have different meanings even though they share the
same value 0xff:
HCI_VENDOR_PKT: HCI packet indicator or type
HCI_EV_VENDOR: event code of a VSE
These usages of HCI_VENDOR_PKT are wrongly checking an event code.
Fix by using HCI_EV_VENDOR for event code.
Also fix warning "CHECK: Unnecessary parentheses around comparison"
given by checkpatch.pl.
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The macros below have different meanings even though they share the
same value 0xff:
HCI_VENDOR_PKT: HCI packet indicator or type
HCI_EV_VENDOR: event code of a VSE
This usage of HCI_VENDOR_PKT is wrongly checking an event code.
Fix by using HCI_EV_VENDOR for event code.
Also fix warning "CHECK: Unnecessary parentheses around comparison"
given by checkpatch.pl.
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The HCI UART write worker assumes that a tty write callback returns a
value in the range from zero through the skb length. A negative value or
a value larger than the skb length is passed to accounting and skb_pull,
which can corrupt skb state.
Treat either return value as a transmit error and discard the skb.
Signed-off-by: Li Qiang <liqiang01@kylinos.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The BCSP transmit path reads an HCI command header when an extension
packet has only been tested for a nonzero length. Its LE configuration
packet handler also indexes bytes through offset seven without a length
check.
Validate the complete command and LE configuration packet headers
before accessing their fields.
Signed-off-by: Li Qiang <liqiang01@kylinos.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The Marvell event handlers access the HCI event header, command
complete payload, and driver-specific event header before validating
that the received skb contains them. A truncated event can consequently
cause an out-of-bounds read.
Validate each header and the command-complete payload length before
dereferencing the corresponding fields.
Signed-off-by: Li Qiang <liqiang01@kylinos.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The USB receive path trusts the block header to contain the required
number of bytes and passes it to the reassembly routine. The routine
also trusts a malformed HCI packet type and can append more data than
the skb allocated from the advertised packet length. A malformed USB
transfer can therefore cause out-of-bounds reads or an skb tail
overwrite.
Validate block header availability, declared block size, packet type,
and reassembly tailroom. Drop the partial frame on an invalid block.
Signed-off-by: Li Qiang <liqiang01@kylinos.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The reset path had two concurrency holes. Both are reachable in
practice when btintel_pcie_hw_error() is invoked from the HCI rx
path while another reset is being requested or is already in
flight.
1. data->reset_type was a plain shared field. The hw_error path
wrote it BEFORE the test_and_set_bit(RECOVERY_IN_PROGRESS)
guard inside btintel_pcie_reset(), so a second hw_error could
clobber the type chosen by an earlier in-flight request:
CPU0 (reset_work) CPU1 (hw_error #2)
dev_data->reset_type = PLDR
T2: read reset_type
dev_data->reset_type = FLR
reset() test_and_set sees 1
-> drops, but type already
clobbered
The hdev->reset callback (.reset = btintel_pcie_reset,
invoked via the sysfs reset attribute
/sys/class/bluetooth/hciX/reset and from hci_cmd_timeout())
compounded this by not writing reset_type at all -- it
inherited whatever value a previous hw_error / resume() had
left, which could be PLDR.
2. btintel_pcie_dump_debug_registers() was called unconditionally
at the top of hw_error(). When reset_work was already running
pci_try_reset_function(), the BT MMIO window can read all-1s
or trigger AER for the duration of the FLR, polluting the
debug dump with no useful information.
Refactor the reset path to make RECOVERY_IN_PROGRESS the sole
serializer for both the type write and the work scheduling:
- Replace btintel_pcie_reset(hdev) with
btintel_pcie_request_reset(data, type). The helper takes the
desired reset variant as a parameter and writes
data->reset_type only after winning test_and_set_bit(); losers
return without touching the field, so concurrent triggers can
no longer clobber an in-flight reset's type. reset_work()'s
read of reset_type is now ordered after the bit transition via
schedule_work()'s memory barrier.
- Add a thin btintel_pcie_hci_reset() wrapper for the
hdev->reset callback (invoked via the sysfs reset attribute
/sys/class/bluetooth/hciX/reset and from hci_cmd_timeout())
that always requests FLR explicitly, so these paths no longer
inherit stale state from prior error events.
- Add an early test_bit(RECOVERY_IN_PROGRESS) gate at the top of
hw_error() so dump_debug_registers() and the recovery-counter
bookkeeping are skipped when a reset is already in flight; the
authoritative test_and_set lives in request_reset() and races
cleanly against any caller that passes the optimistic check.
- Convert the two resume() reset sites (FREEZE/HIBERNATE and the
D0-error path) to request_reset(data, FLR), removing the
redundant manual reset_type writes.
Assisted-by: GitHub-Copilot:claude-4.7-opus
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Wiko Hi MateBook 14 Ryzen 200 laptops (DMI system-product-name
"MNCA-XX", board "M1060") are equipped with an RTL8852BE Wi-Fi/BT
combo chip (rtw89_8852be), whose Bluetooth radio enumerates as
1357:c123 instead of one of the already-supported 1358:c123 / 0bda:c123
identifiers, presumably due to OEM rebranding. Without a matching
entry it only matches the generic USB Bluetooth class fallback, so the
Realtek firmware/config (rtl8852btu_fw.bin / rtl8852btu_config.bin) is
never loaded and the adapter cannot discover or connect to any device,
even though hciconfig reports it as powered and scanning.
Device descriptor:
idVendor 0x1357
idProduct 0xc123
bcdDevice 0.00
iManufacturer 1 Realtek
iProduct 2 Bluetooth Radio
bDeviceClass 224 Wireless
bDeviceSubClass 1 Radio Frequency
bDeviceProtocol 1 Bluetooth
Adding the same BTUSB_REALTEK | BTUSB_WIDEBAND_SPEECH quirk already
used for 1358:c123 and 0bda:c123 fixes firmware loading and normal
operation.
Signed-off-by: Pavel Zverev <playximik29@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
btintel_pcie_coredump_worker() handled three unrelated jobs in one
work item: collect a DRAM trace coredump, read the hardware exception
event, and read the firmware-trigger event. The worker walked three
flag bits at runtime and each interrupt path mutated multiple bits
to communicate which sub-jobs the worker should run, which made the
ownership rules for those bits hard to reason about and entangled
the trigger reason with the in-progress accounting.
Replace the single combined worker with three single-purpose ones,
each owning exactly one flag:
coredump_work -> btintel_pcie_dump_traces()
guarded by COREDUMP_INPROGRESS
hwexp_work -> btintel_pcie_read_hwexp()
guarded by CORE_HALTED (already permanent until
re-probe; HWEXP_INPROGRESS is now redundant
and removed)
fwtrigger_work -> btintel_pcie_dump_fwtrigger_event()
guarded by FWTRIGGER_DUMP_INPROGRESS
All three workers are queued on a shared ordered workqueue (renamed
coredump_workqueue -> dump_workqueue) so a companion event reader
(hwexp/fwtrigger) and the coredump always run FIFO. Companion work
is queued before coredump_work so dmp_hdr.event_type/event_id are
populated by the time dump_traces() consumes them, preserving the
original ordering.
Introduce btintel_pcie_queue_coredump() to centralize the coredump
trigger contract: it is the single writer of COREDUMP_INPROGRESS and
of dmp_hdr.trigger_reason, sets both atomically against concurrent
triggers, and rolls back the bit if the workqueue is disabled
(reset/remove in progress) so a later trigger after re-probe can
succeed. All four trigger sites (HWEXP IRQ, FW-trigger IRQ,
devcoredump user trigger, resume() D0 error path) go through the
helper.
Per-work guard bits are now cleared at the tail of each worker
rather than in the middle of the combined worker, which closes a
subtle race where a duplicate IRQ could observe a cleared bit and
requeue while the previous pass was still finalizing
dev_coredumpv().
reset_work() and remove() now disable_work_sync() all three workers
and, on the FLR-failure path, enable_work() all three to keep their
disable counters balanced. The PLDR/FLR-success contract (re-probe
re-INIT_WORKs everything with counter 0) is preserved.
No functional change to the dump payloads; this is a pure
restructuring of the worker dispatch and its synchronization.
Signed-off-by: Kiran K <kiran.k@intel.com>
Assisted-by: GitHub-Copilot:claude-4.7-opus
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
In nxp_serdev_probe(), if hci_register_dev() succeeds but ps_setup()
fails, the error path jumps to 'probe_fail' which only calls
hci_free_dev() and asserts the reset GPIO, but does NOT call
hci_unregister_dev() first.
This leaves the HCI device registered in the system with its backing
memory freed, leading to a use-after-free when userspace subsequently
accesses the device (e.g. via hciconfig or bluetoothd).
Fix by adding a 'probe_fail_unregister' label that calls
hci_unregister_dev() before falling through to the existing
'probe_fail' label. The original 'probe_fail' label is preserved
for the case where hci_register_dev() itself fails (device was
never registered, so no unregister is needed).
Signed-off-by: Zhao Dongdong <zhaodongdong@kylinos.cn>
Reviewed-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add the vendor/product ID (0x0b05, 0x1d70) to the usb_device_id table for
the Realtek RTL8761CU-based ASUS USB-BT600 adapter. It binds via the
generic Bluetooth class today, so BTUSB_REALTEK is never set and the
rtl8761cu firmware is not loaded, leaving the controller non-functional.
With the entry the driver loads rtl_bt/rtl8761cu_fw.bin (already shipped by
linux-firmware) and the adapter works (tested: A2DP and ASHA).
Similar to commit bc597f0cc44f
("Bluetooth: btusb: Add TP-Link UB600 for Realtek 8761BUV").
Device info from /sys/kernel/debug/usb/devices:
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 23 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0b05 ProdID=1d70 Rev= 2.00
S: Manufacturer=Realtek
S: Product=Bluetooth Controller
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
Cc: stable@vger.kernel.org
Signed-off-by: Christoph Zwerschke <cito@online.de>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add the vendor/product ID (0x0b05, 0x1bef) to the usb_device_id table for
the Realtek RTL8761CU-based ASUS USB-BT540 adapter. It binds via the
generic Bluetooth class today, so BTUSB_REALTEK is never set and the
rtl8761cu firmware is not loaded, leaving the controller non-functional.
With the entry the driver loads rtl_bt/rtl8761cu_fw.bin (already shipped by
linux-firmware) and the adapter works (tested: A2DP and ASHA).
Similar to commit bc597f0cc44f
("Bluetooth: btusb: Add TP-Link UB600 for Realtek 8761BUV").
Device info from /sys/kernel/debug/usb/devices:
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 22 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0b05 ProdID=1bef Rev= 2.00
S: Manufacturer=Realtek
S: Product=Bluetooth Controller
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
Cc: stable@vger.kernel.org
Signed-off-by: Christoph Zwerschke <cito@online.de>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
nokia_setup_fw() walks a length-prefixed firmware stream and
decodes HCI command packets from each record.
Check that each record fits in the remaining firmware image, that command
records contain the HCI command header, and that the payload length is
covered before submitting the command.
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add the USB ID (13d3:3503) for the IMC Networks Qualcomm Atheros
QCA9377 Bluetooth controller to the btusb quirks table. This device
requires Qualcomm Rome firmware and wideband speech support to function
properly; otherwise, BLE scanning fails with HCI unexpected event
opcode 0x2005 errors.
The device reports the following in /sys/kernel/debug/usb/devices:
P: Vendor=13d3 ProdID=3503 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Tibor Harcsa <silurust@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The driver_info field is a bitmask, so use & instead of == to test the
BTUSB_IGNORE bitflag against it, which is consistent with how the other
flags are tested.
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Initialize @priv_size at declaration rather than separately:
- Simpler: one statement completes both declaration and assignment.
- More flexible: the variable is immediately usable from that point,
so any new priv_size += can be freely inserted without caring about
where the separate priv_size = 0 sits.
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
btusb_shutdown_qca() open-codes a synchronous raw HCI reset that is
functionally equivalent to the newly added __hci_reset_sync().
Replace it with __hci_reset_sync() and return its result directly.
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
qca_send_reset() is functionally equivalent to the newly added
__hci_reset_sync().
Drop qca_send_reset() and call __hci_reset_sync() directly.
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
'struct btusb_data' ideally should not include vendor specific
fields, but it currently includes the QCA devcoredump member
'struct qca_dump_info qca_dump'.
Fix by moving it into hci_dev private area accessed by hci_get_priv().
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Devcoredump is not enabled for ATH3012 or QCA_ROME, but they
unconditionally populate devcoredump fields in btusb_setup_qca().
Fix by populating devcoredump fields only when BTUSB_QCA_WCN6855 is
set, which marks the first generation of QCA BT SoCs for which
devcoredump is enabled.
Fixes: 20981ce2d5a5 ("Bluetooth: btusb: Add WCN6855 devcoredump support")
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add @match_id to btusb_data to record the matched usb_device_id
which will be used later.
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
btusb_set_bdaddr_wcn6855() sends the address without swapping byte
order for VSC 0xFC14, but the command expects the address in reversed
byte order compared to other HCI commands like HCI_Create_Connection,
resulting in a wrong BD_ADDR being set.
btmon log on WCN6855 shows VSC 0xFC14 is sent with swapped bytes
11 22 33 44 55 66, and Read BD ADDR returns the expected address
11:22:33:44:55:66:
< HCI Command: Vendor (0x3f|0x0014) plen 6 #3 [hci0]
11 22 33 44 55 66
> HCI Event: Command Complete (0x0e) plen 4 #4 [hci0]
Vendor (0x3f|0x0014) ncmd 1
Status: Success (0x00)
< HCI Command: Read BD ADDR (0x04|0x0009) plen 0 #11 [hci0]
> HCI Event: Command Complete (0x0e) plen 10 #12 [hci0]
Read BD ADDR (0x04|0x0009) ncmd 1
Status: Success (0x00)
Address: 11:22:33:44:55:66 (OUI 11-22-33)
Fix by swapping the input address before issuing the command.
Fixes: b40f58b97386 ("Bluetooth: btusb: Add Qualcomm Bluetooth SoC WCN6855 support")
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
qca_set_bdaddr() waits for HCI_EV_VENDOR when sending
EDL_WRITE_BD_ADDR_OPCODE (0xFC14), but the controller responds with
Command Complete event as confirmed by btmon on WCN7850:
< HCI Command: Vendor (0x3f|0x0014) plen 6 #3 [hci0]
11 22 33 44 55 66
> HCI Event: Command Complete (0x0e) plen 4 #4 [hci0]
Vendor (0x3f|0x0014) ncmd 1
Status: Success (0x00)
Fix by passing 0 as the event parameter to __hci_cmd_sync_ev() to
wait for the command complete event instead.
Fixes: 5c0a1001c8be ("Bluetooth: hci_qca: Add helper to set device address")
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The IMC Networks MT7922 Bluetooth adapter with USB ID 13d3:3625 is not
recognized as a MediaTek device because it is missing from the btusb
device ID table. As a result, btmtk firmware loading is never triggered
and the HCI reset command times out with -ETIMEDOUT.
Add the device with BTUSB_MEDIATEK | BTUSB_WIDEBAND_SPEECH flags,
consistent with the neighboring 13d3:3627, 13d3:3628 and 13d3:3630
entries which use the same chip.
Tested on: MediaTek MT7922 (Wi-Fi 6E combo card, IMC Networks BT USB
interface), kernel 7.0.11-arch1-1.
/sys/kernel/debug/usb/devices:
T: Bus=01 Lev=01 Prnt=01 Port=12 Cnt=03 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3625 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I:* If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Signed-off-by: Gustavo Evgucci <monesss315@gmail.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Enable compiler context analysis for Bluetooth subsystem and drivers.
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add VID 0489 & PID e156 for MediaTek MT7902 USB Bluetooth chip.
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=01 Lev=01 Prnt=01 Port=09 Cnt=05 Dev#= 6 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e156 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I:* If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Co-developed-by: Kirill Shubin <kirill.kz.902@gmail.com>
Signed-off-by: Kirill Shubin <kirill.kz.902@gmail.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
If btusb_qca_send_vendor_req() gets a "short" read from a device, it
will accidentally treat that as a "real" read and populate the returned
value with some unknown and probably totally invalid data.
Fix this logic error up by calling usb_control_msg_recv() which
guarantees a "full" read happens, and then simplify the error checking
for when btusb_qca_send_vendor_req() is called.
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
If btmtk_usb_reg_read() gets a "short" read from a device, it will
accidentally treat that as a "real" read and populate the returned value
with some unknown and probably totally invalid data.
Fix this logic error up by calling usb_control_msg_recv() which
guarantees a "full" read happens, and then simplify the error checking
for when btmtk_usb_reg_read() is called (it's really just
btmtk_usb_id_get() that calls btmtk_usb_reg_read(), so fix up those
return sites.
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
If btmtk_usb_uhw_reg_read() gets a "short" read from a device, it will
accidentally treat that as a "real" read and populate the returned value
with some unknown and probably totally invalid data.
Fix this logic error up by calling usb_control_msg_recv() which
guarantees a "full" read happens, and then simplify the error checking
for when btmtk_usb_uhw_reg_read() is called.
Note, one caller of btmtk_usb_uhw_reg_read() does not check the return
value, but as we pre-initialize the return value as 0, an incorrect read
will not do anything wrong.
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
btintel_diagnostics() accesses tlv->val[0] without first validating
that the diagnostics VSE is long enough to contain that field, so
may cause reading data beyond the received frame.
Fix by validating the length before access.
Fixes: af395330abed ("Bluetooth: btintel: Add Intel devcoredump support")
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
btusb_recv_event_realtek() reads the event code at data[0] and the Realtek
subevent code at data[2] before deciding whether to consume a vendor event
as a coredump.
For example, the two-byte event ff 00 contains a complete vendor-event
header declaring zero parameters. The old classifier still reads a
nonexistent third byte and can misclassify the event as a coredump if the
adjacent byte is 0x34.
Require the HCI event header and first parameter to be present before
inspecting the Realtek subevent code. Short events continue through the
normal HCI receive path, which owns their protocol validation.
Fixes: 044014ce85a1 ("Bluetooth: btrtl: Add Realtek devcoredump support")
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
qca_controller_memdump() allocates qca->qca_memdump before processing
the first dump packet. For a sequence-zero packet it then disables IBS,
marks memdump collection active, and reads the advertised dump size.
If the controller reports a zero dump size, the error path frees the
local qca_memdump object and returns without clearing qca->qca_memdump
or undoing the collection state. A later memdump work item initializes
its local pointer from qca->qca_memdump and skips allocation when that
pointer is non-NULL, so it can operate on freed memory. The stale
collection and IBS-disabled flags can also leave waiters or later
transmit handling blocked behind an aborted dump.
Clear the saved pointer and memdump state before returning from the
invalid-size path, matching the cleanup used when hci_devcd_init() fails.
A static analysis checker reported the stale memdump state, and manual
source review confirmed the invalid-size failure path.
Fixes: 06d3fdfcdf5c ("Bluetooth: hci_qca: Add qcom devcoredump support")
Signed-off-by: Ruoyu Wang <ruoyuw560@gmail.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
rtlbt_parse_firmware() copies patch_length - 4 bytes before appending the
firmware version. A malformed firmware patch shorter than the version field
can make this subtraction underflow and turn the copy into an oversized
read and write during Bluetooth setup.
The existing patch_offset + patch_length check can also wrap on 32-bit
architectures. Validate the patch length and range without arithmetic
overflow before allocating or copying the patch.
Fixes: db33c77dddc2 ("Bluetooth: btrtl: Create separate module for Realtek BT driver")
Cc: stable@vger.kernel.org
Signed-off-by: Laxman Acharya Padhya <acharyalaxman8848@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
In the TLV_TYPE_NVM branch of qca_tlv_check_data() the tag loop bound is
"while (idx < length - sizeof(struct tlv_type_nvm))". "length" is a signed
int from the firmware TLV header and sizeof(struct tlv_type_nvm) is a
size_t (12), so "length" is converted to size_t and any firmware-supplied
"length" < 12 makes the subtraction wrap to a huge value. The loop body
then reads a 12-byte struct tlv_type_nvm past the end of the short
vmalloc'd firmware buffer (and the EDL_TAG_ID_* handlers can write past it).
Rewrite the bound as "idx + sizeof(struct tlv_type_nvm) <= length"; both
operands are non-negative, so it no longer underflows and a "length" too
small for one record correctly skips the loop.
BUG: KASAN: vmalloc-out-of-bounds in qca_download_firmware.isra.0 (drivers/bluetooth/btqca.c:421)
Read of size 2 at addr ffffc900000e5004 by task kworker/u9:0/52
Workqueue: hci0 hci_power_on
Call Trace:
...
kasan_report (mm/kasan/report.c:595)
qca_download_firmware.isra.0 (drivers/bluetooth/btqca.c:421 drivers/bluetooth/btqca.c:617)
qca_uart_setup (drivers/bluetooth/btqca.c:948)
qca_setup (drivers/bluetooth/hci_qca.c:2029)
hci_uart_setup (drivers/bluetooth/hci_ldisc.c:438)
hci_dev_open_sync (net/bluetooth/hci_sync.c:5227)
hci_power_on (net/bluetooth/hci_core.c:920)
process_one_work (kernel/workqueue.c:3322)
worker_thread (kernel/workqueue.c:3486)
kthread (kernel/kthread.c:436)
ret_from_fork (arch/x86/kernel/process.c:158)
ret_from_fork_asm (arch/x86/entry/entry_64.S:245)
Fixes: 2e4edfa1e2bd ("Bluetooth: qca: add missing firmware sanity checks")
Reported-by: Weiming Shi <bestswngs@gmail.com>
Assisted-by: Claude:claude-opus-4-8
Signed-off-by: Xiang Mei <xmei5@asu.edu>
Reported-by: Weiming Shi <bestswngs@gmail.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Pull networking fixes from Paolo Abeni:
"Including fixes from netfilter, Bluetooth and batman-adv.
Current release - regressions:
- bluetooth: fix using chan->conn as indication to no remote netdev
Current release - new code bugs:
- netfilter: cap to maximum number of expectation per master on
updates
Previous releases - regressions:
- bluetooth:
- fix UAF of hci_conn_params in add_device_complete
- fix null ptr deref in hci_abort_conn()
- igmp: remove multicast group from hash table on device destruction
- batman-adv: prevent TVLV OOB check overflow
- eth: mlx5/mlx5e:
- fix off-by-one in single-FDB error rollback
- skip peer flow cleanup when LAG seq is unavailable
- fix crashes in dynamic per-channel stats and HV VHCA agent
- eth: mana: Sync page pool RX frags for CPU
Previous releases - always broken:
- netfilter:
- mark malformed IPv6 extension headers for hotdrop
- terminate table name before find_table_lock()
- ipvs: use parsed transport offset in TCP state lookup
- sched: act_pedit: fix TOCTOU heap OOB write in tc offload
- ethtool: rss: fix hfunc and input_xfrm parsing on big endian
- ipv4/ipv6: fix UAF and memory leak in IGMP/MLD
- tls: consume empty data records in tls_sw_read_sock()
- eth:
- octeontx2-af: fix VF bringup affecting PF promiscuous state
- gue: validate REMCSUM private option length"
* tag 'net-7.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (94 commits)
macsec: don't read an unset MAC header in macsec_encrypt()
dibs: loopback: validate offset and size in move_data()
octeontx2-af: fix VF bringup affecting PF promiscuous state
ethtool: rss: Fix hfunc and input_xfrm parsing on big endian
net/mlx5: Fix L3 tunnel entropy refcount leak
net: macb: drop in-flight Tx SKBs on close
net: mana: Sync page pool RX frags for CPU
net: mana: Validate the packet length reported by the NIC
selftests/net: fix EVP_MD_CTX leak in tcp_mmap
ipvs: ensure inner headers in ICMP errors are in headroom
ipvs: use parsed transport offset in SCTP state lookup
ipvs: use parsed transport offset in TCP state lookup
ipvs: pass parsed transport offset to state handlers
netfilter: handle unreadable frags
netfilter: flowtable: support IPIP tunnel with direct xmit
netfilter: flowtable: IPIP tunnel hardware offload is not yet support
netfilter: flowtable: use dst in this direction when pushing IPIP header
netfilter: ipset: allocate the proper memory for the generic hash structure
netfilter: ipset: cleanup the add/del backlog when resize failed
netfilter: ipset: exclude gc when resize is in progress
...
|
|
bpa10x_setup() sends the vendor command 0xfc0e and passes the response
to bt_dev_info() and hci_set_fw_info() as a "%s" string starting at
skb->data + 1, without checking the length:
bt_dev_info(hdev, "%s", (char *)(skb->data + 1));
hci_set_fw_info(hdev, "%s", skb->data + 1);
A device that returns a one-byte response (status only) leaves
skb->data + 1 past the end of the data, and the %s walk reads adjacent
slab memory until it meets a NUL. The same happens when the payload is
not NUL-terminated within skb->len. The out-of-bounds bytes end up in
the kernel log and the firmware-info debugfs file.
Print the revision string with a bounded "%.*s" limited to skb->len - 1
instead. This keeps the string readable for well-behaved devices while
never reading past the received data, and does not fail setup, so a
device returning a short or unterminated response keeps working.
Fixes: ddd68ec8f484 ("Bluetooth: bpa10x: Read revision information in setup stage")
Reported-by: Xiang Mei <xmei5@asu.edu>
Assisted-by: Claude:claude-opus-4-8
Signed-off-by: Weiming Shi <bestswngs@gmail.com>
Reported-by: Xiang Mei <xmei5@asu.edu>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The FLR branch in btintel_pcie_reset_work() open-coded the entire
re-init sequence: btintel_pcie_release_hdev() (hci_unregister_dev +
hci_free_dev), pci_try_reset_function(), enable_interrupts /
config_msix / enable_bt / reset_ia / start_rx, then
btintel_pcie_setup_hdev() (hci_alloc_dev_priv + hci_register_dev).
Every probe() init step had to be kept in sync with this second
copy in the reset path, and any failure mid-sequence left state to
unwind by hand.
The PLDR path already delegates teardown and re-init to the PCI
core via device_reprobe(): .remove() destroys data through devres
and unregisters hdev, then .probe() rebuilds everything from
scratch. Apply the same model to FLR.
Introduce btintel_pcie_perform_flr() mirroring perform_pldr(). It
runs pci_try_reset_function() (required to avoid the device_lock
ABBA against btintel_pcie_remove(), which calls
disable_work_sync(&reset_work) while holding device_lock) followed
by device_reprobe(). On success, data is destroyed and a fresh
probe re-INIT_WORKs coredump_work with disable count 0, so
enable_work() must not be called; on failure, data is still alive
and the caller balances the earlier disable_work_sync(). The
contract is documented on the helper and reiterated at the
reset_work() call site.
reset_work() shrinks to interrupt/worker drain, dispatch on
reset_type, and the single asymmetry between the two paths. The
out_enable label, the manual unregister/register pair, and the
forward declaration of btintel_pcie_setup_hdev() are dropped.
No intended functional change; FLR and PLDR now share one
teardown contract.
Fixes: 256ab9520d15 ("Bluetooth: btintel_pcie: Support Function level reset")
Assisted-by: GitHub-Copilot:claude-4.7-opus
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
Laxman Acharya Padhya
Kiran K
Chandrashekar Devegowda
Pawel Zalewski (The Capable Hub)
Zijun Hu
Chen Changcheng
Li Qiang
Pavel Zverev
Zhao Dongdong
Christoph Zwerschke
Pengpeng Hou
Tibor Harcsa
Gustavo Evgucci
Pauli Virtanen
Sean Wang
Greg Kroah-Hartman
Ruoyu Wang
Xiang Mei
Linus Torvalds
Weiming Shi