Age | Commit message (Collapse) | Author | Files | Lines |
|
The AVB table contains the CAS_MASTER field (to be added in the next
patch) which decides the direction of the PTP_CLK pin.
Reconfiguring this field dynamically is highly preferable to having to
reset the switch and upload a new static configuration, so we add
support for exactly that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Because the PTP_CLK pin starts toggling only at a time higher than the
current PTP clock, this helper from the time-aware shaper code comes in
handy here as well. We'll use it to transform generic user input for the
perout request into valid input for the sja1105 hardware.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These fields configure the destination and source MAC address that the
switch will put in the Ethernet frames sent towards the CPU port that
contain RX timestamps for PTP.
These fields do not enable the feature itself, that is configured via
SEND_META0 and SEND_META1 in the General Params table.
The implication of this patch is that the AVB Params table will always
be present in the static config. Which doesn't really hurt.
This is needed because in a future patch, we will add another field from
this table, CAS_MASTER, for configuring the PTP_CLK pin function. That
can be configured irrespective of whether RX timestamping is enabled or
not, so always having this table present is going to simplify things a
bit.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
checkpatch found a lack of appropriate whitespace after certain keywords
as per the style guide. Add it in.
Signed-off-by: Logan Magee <mageelog@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
use phy_read_poll_timeout() to replace the poll codes for
simplify tja11xx_check() function.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
use phy_read_poll_timeout() to replace the poll codes for
simplify lan87xx_read_status() function.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
use phy_read_poll_timeout() to replace the poll codes for
simplify the code in phy_poll_reset() function.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
it is sometimes necessary to poll a phy register by phy_read()
function until its value satisfies some condition. introduce
phy_read_poll_timeout() macros that do this.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
use phy_read_mmd_poll_timeout() to replace the poll codes for
simplify mv3310_reset() function.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
use phy_read_mmd_poll_timeout() to replace the poll codes for
simplify aqr107_wait_reset_complete() function.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
use phy_read_mmd_poll_timeout() to replace the poll codes for
simplify bcm84881_wait_init() function.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
it is sometimes necessary to poll a phy register by phy_read_mmd()
function until its value satisfies some condition. introduce
phy_read_mmd_poll_timeout() macros that do this.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
redefined readx_poll_timeout macro by read_poll_timeout to
simplify the code.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
this macro is an extension of readx_poll_timeout macro. the accessor
function op just supports only one parameter in the readx_poll_timeout
macro, but this macro can supports multiple variable parameters for
it. so functions like phy_read(struct phy_device *phydev, u32 regnum)
and phy_read_mmd(struct phy_device *phydev, int devad, u32 regnum) can
also use this poll timeout core. and also expand it can sleep some time
before read operation.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previous changes to the IP routing code have removed all the
tests for the DS_HOST route flag.
Remove the flags and all the code that sets it.
Signed-off-by: David Laight <david.laight@aculab.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/cavium/thunder/nicvf_queues.c: In function nicvf_sq_free_used_descs:
drivers/net/ethernet/cavium/thunder/nicvf_queues.c:1182:12: warning:
variable tail set but not used [-Wunused-but-set-variable]
It's not used since commit 4863dea3fab01("net: Adding support for Cavium ThunderX network controller"),
so remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng zengkai <zhengzengkai@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Provide a flow_dissect callback which returns the network offset and
where to find the skb protocol, given the tags structure a common
function works for both tagging formats that are supported.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Packet trap groups are now explicitly registered by drivers and not
implicitly registered when the packet traps are registered. Therefore,
there is no need to encode entire group structure the trap is associated
with inside the trap structure.
Instead, only pass the group identifier. Refer to it as initial group
identifier, as future patches will allow user space to move traps
between groups.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that drivers explicitly register their supported packet trap groups
there is no for devlink to create them on-demand and destroy them when
their reference count reaches zero.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the previously added API to explicitly register / unregister
supported packet trap groups. This is in preparation for future patches
that will enable drivers to pass additional group attributes, such as
associated policer identifier.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the previously added API to explicitly register / unregister
supported packet trap groups. This is in preparation for future patches
that will enable drivers to pass additional group attributes, such as
associated policer identifier.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, packet trap groups are implicitly registered by drivers upon
packet trap registration. When the traps are registered, each is
associated with a group and the group is created by devlink, if it does
not exist already.
This makes it difficult for drivers to pass additional attributes for
the groups.
Therefore, as a preparation for future patches that require passing
additional group attributes, add an API to explicitly register /
unregister these groups.
Next patches will convert existing drivers to use this API.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So far only the reset bit it set, but the handler executing the reset
is not scheduled. Therefore nothing will happen until some other action
schedules the handler. Improve this by ensuring that the handler is
scheduled.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current implementation makes the implicit assumption that if a bit
is set, then the work is scheduled already. Remove the need for this
implicit assumption and call schedule_work() always. It will check
internally whether the work is scheduled already.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently rtl_task() is designed to handle a large number of tasks.
However we have just one, so we can remove some overhead.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Factor out setting GPHY 10M to new helper rtl8168g_enable_gphy_10m.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes wrapper fn()s around mutex_init/lock/unlock.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Removed MODULE_VERSION and fixed MODULE_AUTHOR.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With MTU sized receive buffers it is not expected to have CQE_RX
with multiple receive buffer pointers. But since same physcial link
is shared by PF and it's VFs, the max receive packet configured
at link could be morethan MTU. Hence there is a chance of receiving
plts morethan MTU which then gets DMA'ed into multiple buffers
and notified in a single CQE_RX. This patch treats such pkts as errors
and frees up receive buffers pointers back to hardware.
Also on the transmit side this patch sets SMQ MAXLEN to max value to avoid
HW length errors for the packets whose size > MTU, eg due to path MTU.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VF shares physical link with PF. Admin function (AF) sends
notification to PF whenever a link change event happens. PF
has to forward the same notification to each of the enabled VF.
PF traps START/STOP_RX messages sent by VF to AF to keep track of
VF's enabled/disabled state.
Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added ethtool support for VF devices for
- Driver stats, Tx/Rx perqueue stats
- Set/show Rx/Tx queue count
- Set/show Rx/Tx ring sizes
- Set/show IRQ coalescing parameters
- RSS configuration etc
It's the PF which owns the interface, hence VF
cannot display underlying CGX interface stats.
Except for this rest ethtool support reuses PF's
APIs.
Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On OcteonTx2 silicon there two two types VFs, VFs that share the
physical link with their parent SR-IOV PF and the VFs which work
in pairs using internal HW loopback channels (LBK). Except for the
underlying Rx/Tx channel mapping from netdev functionality perspective
they are almost identical. This patch adds netdev driver support
for these VFs.
Unlike it's parent PF a VF cannot directly communicate with admin
function (AF) and it has to go through PF for the same. The mailbox
communication with AF works like 'VF <=> PF <=> AF'.
Also functionality wise VF and PF are identical, hence to avoid code
duplication PF driver's APIs are resued here for HW initialization,
packet handling etc etc ie almost everything. For VF driver to compile
as module exported few of the existing PF driver APIs.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When FLR is initiated for a VF (PCI function level reset),
the parent PF gets a interrupt. PF then sends a message to
admin function (AF), which then cleanups all resources attached
to that VF.
Also handled IRQs triggered when master enable bit is cleared
or set for VFs. This handler just clears the transaction pending
ie TRPEND bit.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added 'sriov_configure' to enable/disable virtual functions (VFs).
Also added handling of mailbox messages from these VFs.
Admin function (AF) is the only one with all priviliges to configure
HW, alloc resources etc etc, PFs and it's VFs have to request AF
via mbox for all their needs. But unlike PFs, their VFs cannot
send a mbox request directly. A VF shares a mailbox region with
it's parent PF, so VF sends a mailbox msg to PF and then PF forwards
it to AF. Then AF after processing sends response to PF which it
again forwards to VF.
This patch adds support for this 'VF <=> PF <=> AF' mailbox
communication.
Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Christina Jacob <cjacob@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that phylib notifies the user of a downshift we can remove
this functionality from the driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that phylib notifies the user of a downshift we can remove
this functionality from the driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So far PHY drivers have to check whether a downshift occurred to be
able to notify the user. To make life of drivers authors a little bit
easier move the downshift notification to phylib. phy_check_downshift()
compares the highest mutually advertised speed with the actual value
of phydev->speed (typically read by the PHY driver from a
vendor-specific register) to detect a downshift.
v2:
- Add downshift hint to phy_print_status
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Restart AutoNeg if we didn't get a valid result from previous run.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set XPCS Link as down when AutoNeg is enabled but it didn't finish with
success.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reset the XPCS upon probe stage so that we start it from well known
state.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For 10GKR rate, when link errors are found we need to return fault
status so that XPCS is correctly resumed.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When building arm32 allyesconfig:
ld.lld: error: undefined symbol: __aeabi_uldivmod
>>> referenced by spectrum_cnt.c
>>> net/ethernet/mellanox/mlxsw/spectrum_cnt.o:(mlxsw_sp_counter_resources_register) in archive drivers/built-in.a
>>> did you mean: __aeabi_uidivmod
>>> defined in: arch/arm/lib/lib.a(lib1funcs.o)
pool_size and bank_size are u64; use div64_u64 so that 32-bit platforms
do not error.
Fixes: ab8c4cc60420 ("mlxsw: spectrum_cnt: Move config validation along with resource register")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 53eca1f3479f ("net: rename flow_action_hw_stats_types* ->
flow_action_hw_stats*") renamed just the flow action types and
helpers. For consistency rename variables, enums, struct members
and UAPI too (note that this UAPI was not in any official release,
yet).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
it's still possible for packetdrill to hang in mptcp_sendmsg(), when the
MPTCP socket falls back to regular TCP (e.g. after receiving unsupported
flags/version during the three-way handshake). Adjust MPTCP socket state
earlier, to ensure correct functionality of mptcp_sendmsg() even in case
of TCP fallback.
Fixes: 767d3ded5fb8 ("net: mptcp: don't hang before sending 'MP capable with data'")
Fixes: 1954b86016cf ("mptcp: Check connection state before attempting send")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a dual copper PHY with support for MII/GMII/RGMII on MAC side,
as well as a bunch of other features such as SyncE and Ring Resiliency.
I haven't tested interrupts and WoL, but I am confident that they work
since support is already present in the driver and the register map is
no different for this PHY.
PHY statistics work, PHY tunables appear to work, suspend/resume works.
Signed-off-by: Wes Li <wes.li@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver appears to be secretly enabling the RX clock skew
irrespective of PHY interface type, which is generally considered a big
no-no.
Make them configurable instead, and add TX internal delays when
necessary too.
While at it, configure a more canonical clock skew of 2.0 nanoseconds
than the current default of 1.1 ns.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The helper for configuring the pinout of the MII side of the PHY should
do so irrespective of whether RGMII delays are used or not. So accept
the ID, TXID and RXID variants as well, not just the no-delay RGMII
variant.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is nothing RX-specific about these clock skew values. So remove
"RX" from the name in preparation for the next patch where TX delays are
also going to be configured.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit ed0a72e0de16 ("net/freescale: Clean drivers from static versions")
leave behind this, remove it .
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Kernel TLS forms TLS header in kernel during encryption and removes
while decryption before giving packet back to user application. The
similar logic is introduced in chtls code as well.
v1->v2:
- tls_proccess_cmsg() uses tls_handle_open_record() which is not required
in TOE-TLS. Don't mix TOE with other TLS types.
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|