| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In GFX6 GPUs, compute takes the same CP path as graphics.
CP ME command parser executes packets for each ring buffer:
RB0 supports graphics, RB1 and RB2 are compute only.
Initialize all three rings before calling gfx_v6_0_cp_gfx_start()
to make sure they are all in a sane state before execution starts.
Previously, the two compute-only rings were initialized after
the ME had been already started, which could cause the ME to
start executing the ring contents before the rings could be
properly initialized. This happens to work when the HW is first
initialized, but not during an IP block reset where we want
to reinitialize the compute rings before starting the ME
to prevent it from executing garbage from these rings.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
On GFX6, the compute rings use the same CP path as
the graphics ring. The only difference is that they
don't support draw commands. (As opposed to GFX7 and
newer which have a separate command parser that is
called MEC for compute queues.)
This means that we have to take into consideration
that the PFP also exists on compute queues on GFX6:
Use PFP for register writes on both graphics and
compute queues.
In the pipeline sync, use the PFP to wait for the
previous fence (and not the ME) to prevent the PFP
from starting to execute the next submission while
the ME is still in the previous submission.
After a VM flush, emit PFP_SYNC_ME on compute
queues as well.
Fixes: 2cd46ad22383 ("drm/amdgpu: add graphic pipeline implementation for si v8")
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Implement the emit_switch_buffer() function instead of emitting
them duing emit_ib, emit_pipeline_sync and emit_vm_flush.
Note that it isn't necessary to emit these in both
emit_pipeline_sync() and emit_vm_flush() because
amdgpu_vm_flush() already calls these when calling
either of those functions.
Fixes: 2cd46ad22383 ("drm/amdgpu: add graphic pipeline implementation for si v8")
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Enable the MES process/gang context load from MES local memory,
this will reduce the MES firmware and driver handshake latency.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Michael Chen <michael.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
For specific old eeprom data, mca address is not stored, get mca
address from physical address(pa) and then convert it into pa in
current nps mode.
Also set cur_nps early so the record carries the target nps even
when the conversion returns early.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
For legacy ras eeprom format(only existed on nps1 system), die id
(node instance) is not stored, we get it from mca address and
physical address (pa) here, and now we can calculate pa in any
nps mode for legacy ras eeprom data as well.
It only applies to num_umc == 16 / UMC_VRAM_TYPE_HBM parts.
Also factor out __ras_umc_eeprom_rec2nps_addr() so the die id can
be passed in.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Enabled RS64mem for KFD queues by integrating
process and gang context index allocation in
the per KFD device process and queue creation.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Michael Chen <michael.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The RAS manager uses the rascore debug mode setting to control whether
MCA data is read directly or collected through PMFW MCA polling and
ClearMcaOnRead. Track that debug mode state in ras_mgr so
amdgpu_ras_get_error_query_mode() can classify queries as direct or
firmware-backed.
Limit the PMFW polling wait in recovery to firmware-backed MODE1 fatal
recovery so other reset paths, such as MODE2, do not pay the delay
unnecessarily.
Signed-off-by: Xiang Liu <xiang.liu@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
It's more reasonable to tear down the rs64mem bitmap software
context at MES sw_fini phase. This also can avoid the following
lock order issue.
[ 2529.150983] kworker/u64:1/3134 is trying to acquire lock:
[ 2529.151206] ffff8aebd9a3fa10 (reservation_ww_class_mutex){+.+.}-{4:4}, at: amdgpu_bo_free_kernel+0x4e/0x130 [amdgpu]
[ 2529.151989]
but task is already holding lock:
[ 2529.152227] ffff8aebd2411648 (&reset_domain->sem){++++}-{4:4}, at: amdgpu_device_lock_reset_domain+0x20/0x30 [amdgpu]
[ 2529.153008]
which lock already depends on the new lock.
[ 2529.153342]
the existing dependency chain (in reverse order) is:
[ 2529.153645]
-> #2 (&reset_domain->sem){++++}-{4:4}:
[ 2529.153913] down_read+0x4a/0x240
[ 2529.154081] amdgpu_userq_destroy+0xd8/0x3a0 [amdgpu]
[ 2529.154635] amdgpu_userq_ioctl+0x3e2/0xe30 [amdgpu]
[ 2529.155157] drm_ioctl_kernel+0xaf/0x110 [drm]
[ 2529.155401] drm_ioctl+0x290/0x510 [drm]
[ 2529.155612] amdgpu_drm_ioctl+0x52/0x90 [amdgpu]
[ 2529.156068] __x64_sys_ioctl+0xa0/0xf0
[ 2529.156249] x64_sys_call+0x1278/0x21c0
[ 2529.156434] do_syscall_64+0xbe/0x5f0
[ 2529.156611] entry_SYSCALL_64_after_hwframe+0x76/0x7e
[ 2529.156842]
-> #1 (&userq_mgr->userq_mutex){+.+.}-{4:4}:
[ 2529.157127] __mutex_lock+0xb2/0x11a0
[ 2529.157304] mutex_lock_nested+0x1f/0x30
[ 2529.157492] amdgpu_userq_vm_validate_and_restore_queue+0x710/0x9b0 [amdgpu]
[ 2529.158098] amdgpu_userq_restore_worker+0x39/0x290 [amdgpu]
[ 2529.158646] process_one_work+0x23e/0x6f
-> #0 (reservation_ww_class_mutex){+.+.}-{4:4}:
[ 2529.159832] __lock_acquire+0x14c4/0x2210
[ 2529.160021] lock_acquire+0xc6/0x310
[ 2529.160193] __ww_mutex_lock.constprop.0+0xd9/0x1a30
[ 2529.160419] ww_mutex_lock+0x40/0xb0
[ 2529.160590] amdgpu_bo_free_kernel+0x4e/0x130 [amdgpu]
[ 2529.161077] amdgpu_mes_rs64mem_fini+0x35/0x60 [amdgpu]
[ 2529.161601] mes_v11_0_suspend+0x2d/0x40 [amdgpu]
[ 2529.162102] amdgpu_ip_block_suspend+0x2b/0x70 [amdgpu]
[ 2529.162609] amdgpu_device_ip_suspend_phase2+0xa4/0x270 [amdgpu]
[ 2529.163116] amdgpu_device_pre_asic_reset+0x130/0x1f0 [amdgpu]
[ 2529.163617] amdgpu_device_asic_reset+0x55/0x530 [amdgpu]
[ 2529.164101] amdgpu_device_gpu_recover+0x1e5/0x410 [amdgpu]
[ 2529.164592] amdgpu_userq_mgr_reset_work+0x80/0xa0 [amdgpu]
[ 2529.165140] amdgpu_userq_hang_detect_work+0xbb/0x1c0 [amdgpu]
[ 2529.165693] process_one_work+0x23e/0x6f0
[ 2529.165884] worker_thread+0x1c4/0x380
[ 2529.166065] kthread+0x10c/0x150
[ 2529.166226] ret_from_fork+0x314/0x390
[ 2529.166408] ret_from_fork_asm+0x1a/0x30
[ 2529.166595]
other info that might help us debug this:
[ 2529.166917] Chain exists of:
reservation_ww_class_mutex --> &userq_mgr->userq_mutex --> &reset_domain->sem
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Michael Chen <michael.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
- Unify amdgpu_mes_alloc/free_proc|gang_ctx_index to provide
centralized RS64mem bitmap management for both KGD and KFD.
- Retrieve the bitmap bit for userq contex index based on a
per process granularity.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Michael Chen <michael.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
On gfx12, when more queues are ready than there are HQD slots
(oversubscription), MES keeps queues unmapped and maps a queue to an HQD
on demand when its doorbell rings; a queue is only refetched once its
per-queue work_done is cleared.
Historically oversubscription was handled via the aggregated doorbell,
but that is a shared level-wide signal: MES cannot tell which queue rang
and never clears a queue's work_done, so it relies on the coarse
oversubscription timer to rescan. gfx12 therefore drives GFX/compute
through the per-queue unmapped-doorbell path instead (the aggregated
doorbell now only serves SDMA), which can pinpoint the ringing queue and
lets MES stay idle otherwise.
But with unmapped-doorbell mode 1 (basic) a ring only sets a coarse
level-wide ready flag and does not read the per-queue bitmap or clear the
ringing queue's work_done. A queue still marked done from a prior dispatch
is skipped and its new work is never fetched: the completion never
signals, while queue creation succeeds and no dmesg error is reported.
Switch to mode 2 (basic+): MES reads the per-queue CP_UNMAPPED_QUEUE
bitmap, identifies which queue rang, and clears its work_done so it is
rescheduled promptly. This affects every queue MES schedules on gfx12
(KFD and DRM user queues), which share the one MES instance and this
global setting.
Tested on gfx1201: concurrent multi-queue dispatch that intermittently
stalled under mode 1 now passes on both the KFD and DRM userq paths.
v2: update commit message: describe the oversubscription case, why the
aggregated doorbell is not used for GFX/compute on gfx12, and why
basic+ (not basic) is required.
Signed-off-by: Jesse Zhang <Jesse.Zhang@amd.com>
Reviewed-by: Shaoyun Liu <shaoyun.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
So we can reuse these functions across different ASICs.
In order to simplify code, rename some functions as well.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This version brings along the following updates:
- Add KUnit tests for crtc functions.
- Add KUnit tests for crtc functions.
- Add support for dynamic FFE levels.
- Configure all CRC engines in pipe CRC source path.
- Enable DCN6 compilation.
- Fix ABM over VABC.
- Fix CRC engine 1 enable/disable on DCN3.1.2+.
- Fix MCM blend LUT issues.
- Fix seamless mode switch not triggering for HDR to SDR transition.
- Fix wb_info leak and NULL deref in writeback.
- Increase fclk change latency on dcn351.
- Refactor stream validation.
- Resize MST HDCP per-connector arrays to 32.
- Unify force_yuv debugfs into force_yuv_pixel_format.
- Update VRR info packet to support 12-bit refresh rates.
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Combine two related color manager improvements:
1. Migrate MCM/RMCM, shaper and 3DLUT HW programming to dc_plane_cm
- Continue convergence with upstream Color Manager refactor
- Migrate MCM/RMCM, shaper and 3DLUT programming for dcn401+ to dc_plane_cm
- Unify MCM programming across both legacy and 3DLUT DMA paths
- Add 3DLUT DMA broadcast support for multi-pipe planes
2. Reprogram MCM blend LUT on blend_enable falling edge
- Fix issue where SDR desktop remained desaturated after video playback
- Detect blend_enable falling edge (1->0) in surface update detection
- Force MCM LUT reprogramming on blend state change
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Rafal Ostrowski <rafal.ostrowski@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[How & Why]
Follow-up change to set defaults for HDMI FRL training
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Relja Vojvodic <Relja.Vojvodic@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[How & Why]
- Add support for dynamic FFE levels based on debug config and link rate
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Relja Vojvodic <Relja.Vojvodic@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Description]
DCN6 needs to update BW bounding box in hw init in order to propagate
the Alt-Ch aperture info into DML. In this case update unconditionally
on dcn6 HW init.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
drmm_connector_init() and drmm_encoder_init() register their cleanup
(drm_connector_cleanup() / drm_encoder_cleanup()) as DRM-managed actions
tied to the drm_device lifetime. When the object memory is owned by
KUnit, it is freed before that action runs, so the cleanup touches freed
memory. Allocate these objects with drmm_kzalloc() so their lifetime
matches the cleanup action.
Signed-off-by: Alex Hung <alex.hung@amd.com>
Assisted-by: Copilot:Claude-Opus-4.8
Acked-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Iterate every CRC engine instance when enabling or disabling the pipe CRC
source so DCN31x OTG_CRC1_EN is handled alongside OTG_CRC_EN, matching the
legacy shared enable behavior used by DisplayCRC multi-ROI.
Reviewed-by: ChiaHsuan (Tom) Chung <chiahsuan.chung@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Multi-ROI CRC uses OTG_CRC1_EN for the second engine, but the driver
only toggled OTG_CRC_EN and cleared the whole OTG_CRC_CNTL register on
disable.
[How]
Program engine 1 via OTG_CRC1_EN where supported, disable each
engine independently by crc_eng_inst, and add the missing mask on
relevant DCN ASICs.
Reviewed-by: ChiaHsuan (Tom) Chung <chiahsuan.chung@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Configuring CRC engine 1 via optc35_configure_crc() triggers
ASSERT(mask != 0) in dc_helper.c when programming OTG_CRC1_SELECT.
The DCN3.2 OPTC mask list inherited from dcn32 is missing this field,
so ROI[1] CRC cannot be enabled in DisplayCRC mode on DCN3.5/3.51.
[How]
Add OTG_CRC1_SELECT to OPTC_COMMON_MASK_SH_LIST_DCN3_2, matching the
existing dcn10 definition so REG_UPDATE can program CRC engine 1.
Reviewed-by: ChiaHsuan (Tom) Chung <chiahsuan.chung@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Should have been picked up in 0.1.69.0 promotion commit.
[How]
Add the missing DMUB command-header definitions in dmub_cmd.h:
1. DMUB_CMD__CACP_GET_ACE_CURVE_AREA command ID.
2. Request/response data and command structs.
3. PR runtime flag bit.
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
These registers are used, but were missing from their corresponding lists.
Reviewed-by: Ovidiu (Ovi) Bunea <ovidiu.bunea@amd.com>
Signed-off-by: Matthew Stewart <Matthew.Stewart2@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
ABM does not take effect when brightness
is below twenty percent on VABC LCD panels.
[How]
Create new VESA aux path for brightness
translation functions. When VESA aux enabled
use zero-anchored linear interpolation to
translate instead of the legacy min max
backlight mapping.
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Signed-off-by: Iswara Nagulendran <Iswara.Nagulendran@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add dm_test_crtc_destroy_state_releases_stream to cover the cur->stream
branch of amdgpu_dm_crtc_destroy_state(), complementing the existing
no-stream test.
The test attaches a DC stream to the CRTC state and takes an extra stream
reference so the destroy path drops back to the KUnit-managed reference
instead of freeing the stream, then verifies exactly one reference was
released.
Assisted-by: Copilot:Claude-Opus-4.8
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add dm_test_crtc_enable_vblank_ips_restore_replay to cover the
pr->config.replay_supported side of the sr_supported OR in
amdgpu_dm_crtc_set_vblank().
The existing IPS restore test establishes self-refresh support via the PSR
version. This test instead marks the PSR version unsupported and sets
replay_supported, forcing the sr_supported computation to fall through to
the replay branch while still calling drm_crtc_vblank_restore().
Assisted-by: Copilot:Claude-Opus-4.8
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add dm_test_crtc_enable_vblank_ips_restore to cover the IPS/self-refresh
branch of amdgpu_dm_crtc_set_vblank() that calls drm_crtc_vblank_restore().
The test primes the DC with ips_support set and IPS not fully disabled, a
supported PSR version (self-refresh supported) and an immediate-disable
vblank config, so all four conditions gating the restore hold. A stub
get_vblank_timestamp hook is installed on the CRTC so the restore helper
passes its sanity check, and the enable path then runs to completion.
Assisted-by: Copilot:Claude-Opus-4.8
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add dm_test_crtc_enable_vblank_queues_work and
dm_test_crtc_disable_vblank_queues_work to cover the
vblank_control_workqueue branch of amdgpu_dm_crtc_set_vblank():
- The enable test installs a real workqueue, retains the stream and
queues the control worker, then drains it and checks the active vblank
IRQ count was incremented.
- The disable test drives the no-stream sub-branch (the stream-retain is
skipped) and checks the worker decremented the count.
Both seed the ISM so the queued worker takes no state-machine transition,
keeping coverage on the vblank accounting; the ISM state machine itself
is covered by the ISM tests.
Assisted-by: Copilot:Claude-Opus-4.8
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add coverage for the amdgpu_dm_crtc_set_vblank() paths reached through
amdgpu_dm_crtc_enable_vblank() and amdgpu_dm_crtc_disable_vblank():
- dm_test_crtc_enable_vblank_full_path: VRR-active enable that walks the
vupdate-irq branch and acquires the crtc/pageflip IRQ references.
- dm_test_crtc_enable_vblank_vupdate_busy: vupdate IRQ rejection aborts
the enable with -EBUSY.
- dm_test_crtc_enable_vblank_crtc_irq_error: crtc IRQ acquire failure
aborts the enable with -ENOENT.
- dm_test_crtc_enable_vblank_in_reset: an in-progress GPU reset returns
early before the vblank workqueue branch.
- dm_test_crtc_disable_vblank_vrr: the VRR disable path turns the vupdate
IRQ off and releases both IRQ references.
Add shared IRQ-source stubs and setup helpers so amdgpu_irq_get()/put()
succeed without hardware access.
Assisted-by: Copilot:Claude-Opus-4.8
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
fclk change latency is longer than expected on dcn351.
[How]
Increate fclk change latency from 24us to 32us.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Sung-huai Wang <Danny.Wang@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
The connector exposed a single force_yuv420_output boolean debugfs and
carried force_yuv420_output / force_yuv422_output boolean fields to force a
chroma encoding. This cannot express "force RGB" or "force YCbCr444", and
diverges from the upstream amdgpu_dm which uses a single
force_yuv_pixel_format field keyed on enum dc_pixel_encoding.
[How]
- Replace the two boolean fields with a single uint8_t
force_yuv_pixel_format holding an enum dc_pixel_encoding value
(PIXEL_ENCODING_UNDEFINED == no override).
- Replace the force_yuv420_output boolean debugfs with a read/write
force_yuv_pixel_format file that takes the encoding directly
(1=RGB, 2=YCbCr422, 3=YCbCr444, 4=YCbCr420), validated against
PIXEL_ENCODING_COUNT.
- Convert the existing readers/writers in amdgpu_dm_connector.c to the
new field, preserving current behaviour.
- Add YCbCr444 force support now that the field can express it.
v2: Merge with changed from drm-misc (Alex)
Assisted-by: Copilot:claude-opus-4.8
Reviewed-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
amdgpu_dm_create_validate_stream_for_sink() drove its RGB -> YUV422 ->
YUV420 chroma fallback by recursing and toggling the shared
aconnector->force_yuv420_output / force_yuv422_output fields, resetting
them after each recursive call. Those fields have no locking and the
function runs concurrently on the same connector from two paths: the
connector probe worker (->mode_valid) and a compositor's atomic check
(dm_update_crtc_state). When both run at once, one thread can clear the
override just before the other tests its exit condition, so the exit is
missed and validation loops indefinitely, hanging the modeset path.
[How]
- Replace the recursion with an explicit loop over the chroma encodings
wrapping the existing bpc walk.
- Carry the encoding/bpc selection on the stack, passed by value into
create_stream_for_sink() / fill_stream_properties_from_drm_display_mode(),
instead of mutating shared connector state.
- Derive the supported encodings and bit depths into bitmaps and drive
validation from them, gating each candidate on the sink's advertised
capability so unsupported encodings are never retried.
- Move encoding selection entirely to the caller and pass the chosen
dc_pixel_encoding into fill_stream_properties_from_drm_display_mode().
v2: sqaush in KUnit test fixes, merge with drm-misc changes (Alex)
Assisted-by: Copilot:claude-opus-4.8
Reviewed-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Fix sent -> send in the documentation for all variants of
pvr_kccb_send_cmd*().
Signed-off-by: Luigi Santivetti <luigi.santivetti@imgtec.com>
Reviewed-by: Alexandru Dadu <alexandru.dadu@imgtec.com>
Link: https://patch.msgid.link/20260804-staging-pvr-docs-fixes-v2-3-a5a9569a1c1d@imgtec.com
Signed-off-by: Alessio Belle <alessio.belle@imgtec.com>
|
|
Update Rogue heap memory comments to fix typos.
Signed-off-by: Alexandru Dadu <alexandru.dadu@imgtec.com>
Signed-off-by: Luigi Santivetti <luigi.santivetti@imgtec.com>
Reviewed-by: Alessio Belle <alessio.belle@imgtec.com>
Link: https://patch.msgid.link/20260804-staging-pvr-docs-fixes-v2-2-a5a9569a1c1d@imgtec.com
Signed-off-by: Alessio Belle <alessio.belle@imgtec.com>
|
|
Update and remove some old comment in the PVR GEM documentation.
Signed-off-by: Matt Coster <matt.coster@imgtec.com>
Signed-off-by: Luigi Santivetti <luigi.santivetti@imgtec.com>
Reviewed-by: Alessio Belle <alessio.belle@imgtec.com>
Link: https://patch.msgid.link/20260804-staging-pvr-docs-fixes-v2-1-a5a9569a1c1d@imgtec.com
Signed-off-by: Alessio Belle <alessio.belle@imgtec.com>
|
|
Add dm_test_crtc_set_static_screen_optimze_sr_entry_psr and
dm_test_crtc_set_static_screen_optimze_psr_su_skips to cover the
allow_sr_entry == true path of amdgpu_dm_crtc_set_static_screen_optimze():
the replay/PSR event updates when psr_version < DC_PSR_VERSION_SU_1, and
skipping the PSR event update when psr_version is DC_PSR_VERSION_SU_1.
Assisted-by: Copilot:Claude-Opus-4.8
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add dm_test_crtc_set_vupdate_irq_dc_busy and
dm_test_crtc_set_vupdate_irq_enable to cover the previously untested
paths in amdgpu_dm_crtc_set_vupdate_irq() where an OTG instance is
assigned: dc_interrupt_set() failing (returns -EBUSY) and succeeding
via a mock IRQ service (returns 0 for enable and disable).
Assisted-by: Copilot:Claude-Opus-4.8
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add dm_test_crtc_handle_vblank_completes_cursor_only to cover the
previously untested branch in amdgpu_dm_crtc_handle_vblank() where a
pending event with pflip_status != AMDGPU_FLIP_SUBMITTED (a cursor-only
commit) is signalled: the vblank event is sent, the vblank reference is
dropped, and acrtc->event is cleared.
Assisted-by: Copilot:Claude-Opus-4.8
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Expose amdgpu_dm_crtc_count_crtc_active_planes() for KUnit and add tests
covering the empty plane list and the mixed case exercising the mask
filter, cursor skip, missing plane state, and framebuffer presence
branches.
Assisted-by: Copilot:Claude-Opus-4.8
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Expose amdgpu_dm_idle_worker() for KUnit and add tests covering the
disabled exit, both loop break paths, and the enable-body path. Add
dm_kunit_alloc_dc_state() and dm_kunit_alloc_clk_mgr() helpers to
support the new tests.
Assisted-by: Copilot:Claude-Opus-4.8
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add KUnit coverage for the CRTC vblank paths:
- amdgpu_dm_crtc_handle_vblank: no-event completion and the
AMDGPU_FLIP_SUBMITTED guard that keeps a pending event pending.
- amdgpu_dm_crtc_vblank_control_worker: enable increments, disable
decrements, and disable clamps the active vblank IRQ count at zero.
- amdgpu_dm_crtc_disable_vblank: disable path returns cleanly when the
IRQ subsystem is not installed.
Expose amdgpu_dm_crtc_vblank_control_worker for KUnit via
STATIC_IFN_KUNIT/EXPORT_IF_KUNIT and declare it in the header.
Assisted-by: Copilot:Claude-Opus-4.8
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Expand KUnit coverage for amdgpu_dm_crtc.c with tests for functions that
are easy to exercise in isolation:
- amdgpu_dm_crtc_set_static_screen_optimze(): the !allow_sr_entry early
return.
- amdgpu_dm_crtc_enable_vblank(): rejection with -EINVAL when enabling
vblank on an unconfigured CRTC.
- amdgpu_dm_crtc_update_crtc_active_planes(): the no-stream branch that
resets active_planes to zero.
- amdgpu_dm_crtc_duplicate_state(): DM-specific fields are carried over.
- amdgpu_dm_crtc_reset_state(): a fresh state is allocated and installed.
- amdgpu_dm_crtc_destroy_state(): a stream-less state is freed cleanly.
Expose amdgpu_dm_crtc_destroy_state(), amdgpu_dm_crtc_duplicate_state(),
amdgpu_dm_crtc_reset_state() and amdgpu_dm_crtc_update_crtc_active_planes()
to the tests via STATIC_IFN_KUNIT/EXPORT_IF_KUNIT.
Assisted-by: Copilot:Claude-Opus-4.8
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
The seamless mode switch was not getting triggered during HDR to SDR
transitions, and no DPCD write was observed. Root cause analysis
revealed that incorrect panel capabilities were being reported for PSR
SU panels. Due to the wrong capabilities, the OS was not invoking the
seamless mode switch API, resulting in no DPCD communication and also
gated eDP teardown across the seamless mode switch hold.
[How]
Fixed by setting the correct power panel capabilities for PSR SU panels.
This ensures the OS receives accurate panel capability information and
triggers the seamless mode switch API as expected, restoring proper
DPCD writes during HDR to SDR transitions.
The DC commit sequence was tearing the eDP down anyway -- backlight off,
ABM disable, DPMS off, PSR/Replay enable state cleared, PHY TX off,
OTG/OPTC off; all these actions are blocked now with the
skip_implict_edp_power_control
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Karthi Kandasamy <karthi.kandasamy@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHAT]
dc_stream_add_writeback() copies wb_info by value, so free it on all
paths via a single cleanup label. Also bail out early when no pipe_ctx
matches the stream to avoid a NULL pointer dereference.
Assisted-by: Copilot:Claude-Opus-4.8
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
hdmi_frl_status_polling_work() skipped any link whose connector_signal
was not SIGNAL_TYPE_HDMI_FRL. connector_signal is not reliably set to
SIGNAL_TYPE_HDMI_FRL while a link is actually running FRL, so links that
were operating in FRL mode were skipped and their status flags never got
polled, missing link-retrain events.
[How]
Use frl_link_settings.frl_link_rate to decide whether a link is running
FRL. A non-zero rate means FRL is active, so only links with a zero rate
are skipped. This ensures every link actually operating in FRL mode is
polled for status changes.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
VRR info packet previously only supported up to 10-bit refresh rate values
limiting the range of FreeSync minimum and maximum refresh rates that
could be encoded.
[How]
Expanded the bit masking in PB11/PB12 from 2 to 4 bits to capture bits
11:8 of the minimum and maximum FreeSync refresh rates, enabling the VRR
info packet to encode 12-bit refresh rate values.
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Signed-off-by: Harry VanZyllDeJong <hvanzyll@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
ensure dtbclk is enabled before hdmistreamclk_en
pmfw could stop dtbclk on idle.
driver needs to ensure dtbclk enabled is enabled before hdmistreamclk_en
also disable debounce timer on dcn42.
Reviewed-by: Chris Park <chris.park@amd.com>
Reviewed-by: Leo Chen <leo.chen@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
dm_dp_mst_get_modes() uses drm_connector->index to index the
per-connector HDCP arrays in struct hdcp_workqueue. Those arrays are
sized to AMDGPU_DM_MAX_DISPLAY_COUNT, which matches the DRM connector
index range (0..31). Add a defensive bounds check so that, should the
DRM connector index range ever grow beyond the array size, the access
is skipped instead of reading and writing out of bounds.
Assisted-by: Copilot:claude-opus-4.8
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
AMDGPU_DM_MAX_DISPLAY_INDEX is 31. It suggest a maximum number of
32 connectors. But the way it's used is like MAX_DISPLAY_COUNT.
Hence we're off by one with DRM core, which supports a max of 32
connectors.
Rename AMDGPU_DM_MAX_DISPLAY_INDEX to AMDGPU_DM_MAX_DISPLAY_COUNT
to match its actual use, and increase the size to 32 to match the
originally intended size.
Fixes: 82986fd631fa ("drm/amd/display: save restore hdcp state when display is unplugged from mst hub")
Assisted-by: Copilot:claude-opus-4.8
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Set bits on dword 2 like GFX7-8 except load_global_uconfig
which doesn't exist on GFX6.
Emit VS_PARTIAL_FLUSH before VGT_FLUSH like GFX7-8.
For reference see old PAL which explains the bit fields in
this register and that load_global_uconfig doesn't exist on GFX6
and also see gfx_v7_ring_emit_cntxcntl() for the GFX7 code
which this commit follows.
Fixes: 2cd46ad22383 ("drm/amdgpu: add graphic pipeline implementation for si v8")
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
Timur Kristóf
Prike Liang
Tao Zhou
Xiang Liu
Jesse Zhang
Taimur Hassan
Rafal Ostrowski
Relja Vojvodic
Alvin Lee
Alex Hung
Wayne Lin
Matthew Stewart
Iswara Nagulendran
Bhawanpreet Lakha
Sung-huai Wang
Ivan Lipski
Alessio Belle
Alexandru Dadu
Matt Coster
Karthi Kandasamy
Fangzhi Zuo
Harry VanZyllDeJong
Charlene Liu
Harry Wentland