| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
When clock support was added to the i2c-mv64xxx, not all clk functions
had stubs when for !CONFIG_HAVE_CLK configurations. However, nowadays,
both "struct clk" and all the clock framework functions have stubs
when CONFIG_HAVE_CLK is not enabled, so it no longer makes sense to
carry such compile-time conditionals in the driver.
This commit was compile tested on both ARM64 (which has both
CONFIG_OF=y and CONFIG_HAVE_CLK=y) and PowerPC c2k_defconfig (which
has CONFIG_OF=y, CONFIG_HAVE_CLK disabled, and the i2c-mv64xxx driver
enabled).
The only non-trivial change is in the mv64xxx_of_config() function,
which was returning -ENODEV unconditionally if CONFIG_HAVE_CLK was
disabled. Simply removing this condition works fine because the first
test done by the function is to verify if drv_data->clk points to a
valid clock, and if it doesn't, we return -ENODEV. When
CONFIG_HAVE_CLK is disabled, devm_clk_get() unconditionally returns
NULL, so mv64xxx_of_config() will return -ENODEV when no clock is
provided, which is the intended behavior.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Instead of separately calling clk_prepare()/clk_enable(), use
clk_prepare_enable(), and instead of calling
clk_disable()/clk_unprepare(), use clk_disable_unprepare(). Those
handy shortcuts have been introduced specifically to simplify the
numerous call sites were both functions were called in sequence.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
If a clock is registered by a platform driver and not by the
OF_CLK_DECLARE() mechanism, it might show up after the first attempt
to probe i2c-mv64xxx. In order to solve this, we need to handle
-EPROBE_PREFER as a special return value of devm_clk_get(), and return
the same error code from probe().
This gives us three situations:
- There is no reference to a clock in the DT. In this case,
devm_clk_get() returns an error that is not -EPROBE_DEFER
(something like -ENODEV), and we continue the probing without
enabling the clock.
- There is a reference to the clock in the DT, and the clock is
ready. devm_clk_get() returns a valid reference to the clock, and
we prepare/enable it.
- There is a reference to the clock in the DT, but the clock is not
ready. devm_clk_get() returns -EPROBE_DEFER, and we exit from
probe() with the same error code so that probe() is tried again
later.
This is needed for Marvell Armada 7K/8K, where the clock driver is a
platform driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
According to the datasheets the n factor for dividing the tclk is
2 to the power n on Allwinner SoCs, not 2 to the power n + 1 as it is
on other mv64xxx implementations.
I've contacted Allwinner about this and they have confirmed that the
datasheet is correct.
This commit fixes the clk-divider calculations for Allwinner SoCs
accordingly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
Commit 00d8689b85a7 ("i2c: mv64xxx: rework offload support to fix
several problems") completely reworked the offload support, but left a
debugging-related "return false" at the beginning of the
mv64xxx_i2c_can_offload() function. This has the unfortunate consequence
that offloading is in fact never used, which wasn't really the
intention.
This commit fixes that problem by removing the bogus "return false".
Fixes: 00d8689b85a7 ("i2c: mv64xxx: rework offload support to fix several problems")
Signed-off-by: Hezi Shahmoon <hezi@marvell.com>
[Thomas: reworked commit log and title.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: <stable@vger.kernel.org>
|
|
Originally, the I2C controller supported by the i2c-mv64xxx driver
requires a lot of software support: an interrupt is generated at each
step of an I2C transaction (after the start bit, after sending the
address, etc.) and the driver is in charge of re-programming the I2C
controller to do the next step of the I2C transaction. This explains
the fairly complex state machine that the driver has.
On Marvell Armada XP and later processors (Armada 375, 38x, etc.), the
I2C controller was extended with a part called the "I2C Bridge", which
allows to offload the I2C transaction completely to the
hardware. Initial support for this mechanism was added in commit
930ab3d403a ("i2c: mv64xxx: Add I2C Transaction Generator support").
However, the implementation done in this commit has two related
issues, which this commit fixes by completely changing how the offload
implementation is done:
* SMBus read transfers, where there is one write to select the
register immediately followed in the same transaction by one read,
were making the processor hang. This was easier visible on the
Marvell Armada XP WRT1900AC platform using a driver for an I2C LED
controller, or on other Armada XP platforms by using a simple
'i2cget' command to read an I2C EEPROM.
* The implementation was based on the fact that the offload engine
was re-programmed to transfer each message of an I2C xfer: this
meant that each message sent with the offload engine was starting
with a normal I2C start sequence. However, the I2C subsystem
assumes that all messages belonging to the same xfer will use the
so-called "repeated start" so that the entire I2C xfer is seen as
one transfer by the I2C devices and cannot be interrupt by other
I2C masters on the same bus.
In fact, the "I2C Bridge" allows to offload three types of xfer:
- xfer of one write message
- xfer of one read message
- xfer of one write message followed by one read message
For all other situations, we have to fallback to not using the "I2C
Bridge" in order to get proper I2C semantics.
Therefore, this commit reworks the offload implementation to put it
not at the message level, but at the xfer level: in the
mv64xxx_i2c_xfer() function, we decide if the transaction can be
offloaded (in which case it is handled by the
mv64xxx_i2c_offload_xfer() function), or otherwise it is handled by
the slow path (implemented in the existing mv64xxx_i2c_execute_msg()).
This allows to simplify the state machine, which no longer needs to
have any state related to the offload implementation: the offload
implementation is now completely separated from the slow path (with
the exception of the interrupt handler, of course).
In summary:
- mv64xxx_i2c_can_offload() will analyze an I2C xfer and decided of
the "I2C Bridge" can be used to offload it or not.
- mv64xxx_i2c_offload_xfer() will actually program the "I2C Bridge"
to offload one xfer (of either one or two messages), and block
using mv64xxx_i2c_wait_for_completion() until the xfer completes.
- The interrupt handler mv64xxx_i2c_intr() is modified to push the
offload related code to a separate function,
mv64xxx_i2c_intr_offload(). It will take care of reading the
received data if needed.
This commit was tested on:
- Armada XP OpenBlocks AX3-4 (EEPROM on I2C and RTC on I2C)
- Armada XP WRT1900AC (LED controller on I2C)
- Armada XP GP (EEPROM on I2C)
Fixes: 930ab3d403ae ("i2c: mv64xxx: Add I2C Transaction Generator support")
Cc: <stable@vger.kernel.org> # v3.12+
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
[wsa: fixed checkpatch warnings]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The "clock-frequency" DT property is listed as optional, However,
the current code stores the return value of of_property_read_u32 in
the return code of mv64xxx_of_config, but then forgets to clear it
after setting the default value of "clock-frequency". It is then
passed out to the main probe function, resulting in a probe failure
when "clock-frequency" is missing.
This patch checks and then throws away the return value of
of_property_read_u32, instead of storing it and having to clear it
afterwards.
This issue was discovered after the property was removed from all
sunxi DTs.
Fixes: 4c730a06c19bb ("i2c: mv64xxx: Set bus frequency to 100kHz if clock-frequency is not provided")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Cc: stable@vger.kernel.org
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This driver has been flagged to drop class based instantiation. The removal
improves boot-up time and is unneeded for embedded controllers. Users have been
warned to switch for some time now, so we can actually do the removal. Keep the
DEPRECATED flag, so the core can inform users that the behaviour finally
changed now. After another transition period, this flag can go, too.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The Allwinner A10 compatibles were following a slightly different compatible
patterns than the rest of the SoCs for historical reasons. Move to the other
pattern for consistency across all Allwinner Socs.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[wsa: dropped binding OK as per
http://lists.infradead.org/pipermail/linux-arm-kernel/2014-February/229438.html]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The reset framework recently gained optional stubs when CONFIG_RESET_CONTROLLER
is not selected. It also introduced a function reset_get_optional, that is also
dummy-defined whenever the framework isn't enabled, for drivers that needs an
optional reset controller.
Switch to this function, since the mv64xxx driver is in this case. This also
fixes a compilation breakage whenever the reset framework wasn't selected:
drivers/i2c/busses/i2c-mv64xxx.c:771:2: error: implicit declaration of function 'devm_reset_control_get'
While we're at it, remove the redundant test on dev.of_node surrounding the
calls to reset framework functions, since it will either be a valid pointer, an
error pointer in the case where we called reset_get_optional without an of_node
pointer or if it failed, or NULL if we're not loaded through DT.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
We now have a central place to put this code to.
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Calling the state machine with a definite state which is only used in
this context is superfluous. Do it directly.
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
For start and restart, we are doing the same thing. Let's consolidate
that.
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The Allwinner A31 I2C controller is almost identical to the one used in the
other Allwinner SoCs, except for the fact that it needs to clear the interrupt
by setting the INT_FLAGS bit in the control register, instead of clearing it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The Allwinner A31 SoC using that IP has a reset controller maintaining
it reset unless told otherwise.
Add some optional reset support to the driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Because the offload mechanism can fall back to a standard transfer,
having two seperate initialization states is unfortunate. Let's just
have one state which does things consistently. This fixes a bug where
some preparation was missing when the fallback happened. And it makes
the code much easier to follow. To implement this, we put the check
if offload is possible at the top of the offload setup function.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: stable@vger.kernel.org # v3.12+
Fixes: 930ab3d403ae (i2c: mv64xxx: Add I2C Transaction Generator support)
|
|
The first variants of Armada XP SoCs (A0 stepping) have issues related
to the i2c controller which prevent to use the offload mechanism and
lead to a kernel hang during boot.
The commit introduces a new the compatible string
marvell,mv78230-a0-i2c for the i2c controller. When this compatible
string is used the driver disables the offload mechanism and the
kernel no more hangs on these SoCs.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reported-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: stable@vger.kernel.org # v3.12+: af8d1c63afcb: ARM: mvebu: Add support to get the ID and the revision of a SoC
Cc: stable@vger.kernel.org # v3.12+: 85e618a1be2b: ARM: mvebu: Add quirk for i2c for the OpenBlocks AX3-4 board
Cc: stable@vger.kernel.org # v3.12+
Fixes: 930ab3d403ae (i2c: mv64xxx: Add I2C Transaction Generator support)
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The driver is used on PowerPC which don't provide writel_relaxed(). This
breaks the c2k and prpmc2800 default configurations. To fix the build,
turn the calls to writel_relaxed() into writel(). The impacts for ARM
should be minimal.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Some functions and variables are only used if the configuration selects
HAVE_CLK. Protect them with a corresponding #ifdef CONFIG_HAVE_CLK block
to avoid compiler warnings.
Signed-off-by: Thierry Reding <treding@nvidia.com>
[wsa: added marker to #endif]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
I2C of helpers used to live in of_i2c.c but experience (from SPI) shows
that it is much cleaner to have this in the core. This also removes a
circular dependency between the helpers and the core, and so we can
finally register child nodes in the core instead of doing this manually
in each driver. So, fix the drivers and documentation, too.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
All the Armada XP (mv78230, mv78260 and mv78460) have a silicon issue
in the I2C controller which violate the i2c repeated start
timing. The I2C standard requires a minimum of 4.7us for the repeated
start condition whereas the I2C controller of the Armada XP this time
is 2.9us.
So this patch adds a 5us delay for the start case only if the
the compatible i2c-mv78230 is set.
Based on the initals patches from Zbigniew Bodek
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Zbigniew Bodek <zbb@semihalf.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The I2C Transaction Generator offloads CPU from managing I2C
transfer step by step.
This feature is currently only available on Armada XP, so usage of
this mechanism is activated through device tree.
Based on the work of Piotr Ziecik and rewrote to use the new way of
handling multiples i2c messages.
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This commit adds checking whether clock-frequency property acquisition
has succeeded. If not, the frequency is set to 100kHz by default.
The Device Tree binding documentation is updated accordingly.
Based on the intials patches from Zbigniew Bodek
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Zbigniew Bodek <zbb@semihalf.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The driver returns -ENODEV as error code if it did not get an ACK
from the device. Per Documentation/i2c/fault-codes, it should
return -ENXIO.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Add the compatible string for the Allwinner A10 i2c controller and the
associated register layout.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The Allwinner i2c controller uses the same logic as the Marvell one, but
with slightly different register offsets.
Introduce a structure that will be passed by either the pdata or
associated to the compatible strings, and that holds the various
registers that might be needed.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
These macros make it more comprehensive to access to useful masked and
shifted area of the various registers used.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Asking for a multi-part message to be handled by this driver is racy; it
has been observed that the following sequence is possible with this
driver:
- send start
- send address + write
- send data
- send (repeated) start
- send address + write
- send (repeated) start
- send address + read
- unrecoverable bus hang (except by system reset)
The problem is that the interrupt handling sees the next event after the
first repeated start is sent - the IFLG bit is set in the register even
though INTEN is disabled.
Let's fix this by moving all of the message processing into interrupt
context, rather than having it partly in IRQ and partly in process
context. This allows us to move immediately to the next message in the
interrupt handler and get on with the transfer, rather than incuring a
couple of scheduling switches to get the next message.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Move mv64xxx_i2c_prepare_for_io() higher up in the driver to avoid a
future forward declaration for this function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
As this driver does not advertise protocol mangling support
(I2C_FUNC_PROTOCOL_MANGLING is not set), having code to act on
I2C_M_NOSTART is illogical, and in any case isn't supportable on
anything but the first message - which makes no sense. Remove
the I2C_M_NOSTART code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Propagate the error code from request_irq() rather than ignoring it
entirely.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
As we're changing to using devm_* APIs to fix various problems
in this driver, lets also do devm_kzalloc() while we're here too.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This driver forgets to use clk_put(). Rather than adding clk_put(),
lets instead use devm_clk_get() to obtain this clock so that it's
automatically handled on cleanup.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Eliminate reg_base_p and reg_size, mv64xxx_i2c_unmap_regs() and an
unchecked ioremap() return from this driver by using the devm_*
API for requesting and ioremapping resources.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
mv64xxx_i2c_map_regs() already returns an error code, so lets
propagate that to mv64xxx_i2c_probe()'s caller.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Do not use interruptible waits in an I2C driver; if a process uses
signals (eg, Xorg uses SIGALRM and SIGPIPE) then these signals can
cause the I2C driver to abort a transaction in progress by another
driver, which can cause that driver to fail. I2C drivers are not
expected to abort transactions on signals.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
i2c_del_adapter() always returns 0. So all checks testing whether it will be
non zero will always evaluate to false and the conditional code is dead code.
This patch updates all callers of i2c_del_mux_adapter() to ignore the return
value and assume that it will always succeed (which it will). In a subsequent
patch the return type of i2c_del_adapter() will be made void.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com> (for ocores and mux-gpio)
Acked-by: Havard Skinnemoen <hskinnemoen@gmail.com> (for i2c-gpio)
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn> (for puf3)
Acked-by: Barry Song <baohua.song@csr.com> (for sirf)
Reviewed-by: Jean Delvare <khali@linux-fr.org>
[wsa: Fixed "foo* bar" flaws while we are here]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
Extends the driver to get properties from device tree. Rather than
pass the N & M factors in DT, use the more standard clock-frequency
property. Calculate N & M at run time. In order to do this, we need to
know tclk. So the driver uses clk_get() etc in order to get the clock
and clk_get_rate() to determine the tclk rate. Not all platforms
however have CLK, so some #ifdefery is needed to ensure the driver
still compiles when CLK is not available.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[wsa: converted some ints to u32 to match signedness]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
The driver currently checks the platform device id and rejects platform
device id different from 0. This prevents the registration of a second
i2c controller on systems where a second one might be available (such as
Kirkwood 88F6282).
CC: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
Convert the drivers in drivers/i2c/busses/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Cc: Ben Dooks <ben-linux@fluff.org>
Acked-by: Jochen Friedrich <jochen@scram.de>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: Barry Song <21cnbao@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Yong Zhang <yong.zhang0@gmail.com>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
As stated into file include/linux/i2c.h we must send a repeated START
between messages in the same xfer groupset:
* Except when I2C "protocol mangling" is used, all I2C adapters implement
* the standard rules for I2C transactions. Each transaction begins with a
* START. That is followed by the slave address, and a bit encoding read
* versus write. Then follow all the data bytes, possibly including a byte
* with SMBus PEC. The transfer terminates with a NAK, or when all those
* bytes have been transferred and ACKed. If this is the last message in a
* group, it is followed by a STOP. Otherwise it is followed by the next
* @i2c_msg transaction segment, beginning with a (repeated) START.
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Mauro Barella <mbarella@vds-it.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
As warned by checkpatch.pl, <linux/io.h> should be used instead of
<asm/io.h>.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
|
I2C bus drivers don't have to support I2C_M_REV_DIR_ADDR. It is a
deviation from the I2C specification, which only makes sense to
implement when really needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
|
Thomas Petazzoni
Hans de Goede
Hezi Shahmoon
Wolfram Sang
Chen-Yu Tsai
Maxime Ripard
Gregory CLEMENT
Sachin Kamat
Thierry Reding
Jingoo Han
Guenter Roeck
Russell King
Lars-Peter Clausen
Bill Pemberton
Andrew Lunn
Florian Fainelli
Axel Lin
Rodolfo Giometti
H Hartley Sweeten
Tejun Heo
Jean Delvare