| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
All files related to this driver contain the following notice:
See LICENSE.qla3xxx for copyright and licensing details.
LICENSE.qla3xxx can be found in
Documentation/networking/device_drivers/qlogic/. The file contains:
- A copyright notice
This copyright notice is redundant as all files contain the same
copyright notice already
- A license notice
You may modify and redistribute the device driver code under the GNU
General Public License (a copy of which is attached hereto as Exhibit
A) published by the Free Software Foundation (version 2 or a later
version).
This can be replaced with the corresponding SPDX license identifier
(GPL-2.0-or-later) in the source files which reference this license
file.
- A license for the device firmware
This license is pointless in the context of the kernel as the firmware
is not distributed as part of the kernel.
LICENSE.qla2xxx contained exactly the same firmware license which was
removed with commit bc3f957c069f ("[SCSI] qla2xxx: Update
LICENSE.qla2xxx.").
The firmware license is there due to the fact that the out of tree
driver tarball which was available from the qlogic website contained
the firmware binary. The firmware license in the qla3xxx license file
got probably forgotten when the other qlogic license files were
updated.
Remove the notices and add the SPDX license identifier GPL-2.0-or-later to
the source files.
Finally remove the now redundant LICENSE.qla3xxx file.
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
All files in this driver directory contain the following notice:
See LICENSE.qlcnic for copyright and licensing details.
LICENSE.qlacnic can be found in
Documentation/networking/device_drivers/qlogic/. The file contains:
- A copyright notice
This copyright notice is redundant as all files contain the same
copyright notice already
- A license notice
You may modify and redistribute the device driver code under the
GNU General Public License (a copy of which is attached hereto as
Exhibit A) published by the Free Software Foundation (version 2).
This can be replaced with the corresponding SPDX license identifier
(GPL-2.0-only) in the source files which reference this license
file.
- The full GPLv2 license text
A redundant copy of LICENSES/preferred/GPL-2.0
Remove the notices and add the SPDX license identifier GPL-2.0-only to the
source files.
Finally remove the now redundant LICENSE.qlcnic file.
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Acked-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull networking fixes from David Miller:
1) Use netif_rx_ni() when necessary in batman-adv stack, from Jussi
Kivilinna.
2) Fix loss of RTT samples in rxrpc, from David Howells.
3) Memory leak in hns_nic_dev_probe(), from Dignhao Liu.
4) ravb module cannot be unloaded, fix from Yuusuke Ashizuka.
5) We disable BH for too lokng in sctp_get_port_local(), add a
cond_resched() here as well, from Xin Long.
6) Fix memory leak in st95hf_in_send_cmd, from Dinghao Liu.
7) Out of bound access in bpf_raw_tp_link_fill_link_info(), from
Yonghong Song.
8) Missing of_node_put() in mt7530 DSA driver, from Sumera
Priyadarsini.
9) Fix crash in bnxt_fw_reset_task(), from Michael Chan.
10) Fix geneve tunnel checksumming bug in hns3, from Yi Li.
11) Memory leak in rxkad_verify_response, from Dinghao Liu.
12) In tipc, don't use smp_processor_id() in preemptible context. From
Tuong Lien.
13) Fix signedness issue in mlx4 memory allocation, from Shung-Hsi Yu.
14) Missing clk_disable_prepare() in gemini driver, from Dan Carpenter.
15) Fix ABI mismatch between driver and firmware in nfp, from Louis
Peens.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (110 commits)
net/smc: fix sock refcounting in case of termination
net/smc: reset sndbuf_desc if freed
net/smc: set rx_off for SMCR explicitly
net/smc: fix toleration of fake add_link messages
tg3: Fix soft lockup when tg3_reset_task() fails.
doc: net: dsa: Fix typo in config code sample
net: dp83867: Fix WoL SecureOn password
nfp: flower: fix ABI mismatch between driver and firmware
tipc: fix shutdown() of connectionless socket
ipv6: Fix sysctl max for fib_multipath_hash_policy
drivers/net/wan/hdlc: Change the default of hard_header_len to 0
net: gemini: Fix another missing clk_disable_unprepare() in probe
net: bcmgenet: fix mask check in bcmgenet_validate_flow()
amd-xgbe: Add support for new port mode
net: usb: dm9601: Add USB ID of Keenetic Plus DSL
vhost: fix typo in error message
net: ethernet: mlx4: Fix memory allocation in mlx4_buddy_init()
pktgen: fix error message with wrong function name
net: ethernet: ti: am65-cpsw: fix rmii 100Mbit link mode
cxgb4: fix thermal zone device registration
...
|
|
If tg3_reset_task() fails, the device state is left in an inconsistent
state with IFF_RUNNING still set but NAPI state not enabled. A
subsequent operation, such as ifdown or AER error can cause it to
soft lock up when it tries to disable NAPI state.
Fix it by bringing down the device to !IFF_RUNNING state when
tg3_reset_task() fails. tg3_reset_task() running from workqueue
will now call tg3_close() when the reset fails. We need to
modify tg3_reset_task_cancel() slightly to avoid tg3_close()
calling cancel_work_sync() to cancel tg3_reset_task(). Otherwise
cancel_work_sync() will wait forever for tg3_reset_task() to
finish.
Reported-by: David Christensen <drc@linux.vnet.ibm.com>
Reported-by: Baptiste Covolato <baptiste@arista.com>
Fixes: db2199737990 ("tg3: Schedule at most one tg3_reset_task run")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the registers being written to as the values were being over written
when writing the same registers.
Fixes: caabee5b53f5 ("net: phy: dp83867: support Wake on LAN")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix an issue where the driver wrongly detected ipv6 neighbour updates
from the NFP as corrupt. Add a reserved field on the kernel side so
it is similar to the ipv4 version of the struct and has space for the
extra bytes from the card.
Fixes: 9ea9bfa12240 ("nfp: flower: support ipv6 tunnel keep-alive messages from fw")
Signed-off-by: Louis Peens <louis.peens@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change the default value of hard_header_len in hdlc.c from 16 to 0.
Currently there are 6 HDLC protocol drivers, among them:
hdlc_raw_eth, hdlc_cisco, hdlc_ppp, hdlc_x25 set hard_header_len when
attaching the protocol, overriding the default. So this patch does not
affect them.
hdlc_raw and hdlc_fr don't set hard_header_len when attaching the
protocol. So this patch will change the hard_header_len of the HDLC
device for them from 16 to 0.
This is the correct change because both hdlc_raw and hdlc_fr don't have
header_ops, and the code in net/packet/af_packet.c expects the value of
hard_header_len to be consistent with header_ops.
In net/packet/af_packet.c, in the packet_snd function,
for AF_PACKET/DGRAM sockets it would reserve a headroom of
hard_header_len and call dev_hard_header to fill in that headroom,
and for AF_PACKET/RAW sockets, it does not reserve the headroom and
does not call dev_hard_header, but checks if the user has provided a
header of length hard_header_len (in function dev_validate_header).
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We recently added some calls to clk_disable_unprepare() but we missed
the last error path if register_netdev() fails.
I made a couple cleanups so we avoid mistakes like this in the future.
First I reversed the "if (!ret)" condition and pulled the code in one
indent level. Also, the "port->netdev = NULL;" is not required because
"port" isn't used again outside this function so I deleted that line.
Fixes: 4d5ae32f5e1e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VALIDATE_MASK(eth_mask->h_source) is checked twice in a row in
bcmgenet_validate_flow(). Add VALIDATE_MASK(eth_mask->h_dest)
instead.
Fixes: 3e370952287c ("net: bcmgenet: add support for ethtool rxnfc flows")
Signed-off-by: Denis Efremov <efremov@linux.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for a new port mode that is a backplane connection without
support for auto negotiation.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Keenetic Plus DSL is a xDSL modem that uses dm9620 as its USB interface.
Signed-off-by: Kamil Lorenc <kamil@re-ws.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On machines with much memory (> 2 TByte) and log_mtts_per_seg == 0, a
max_order of 31 will be passed to mlx_buddy_init(), which results in
s = BITS_TO_LONGS(1 << 31) becoming a negative value, leading to
kvmalloc_array() failure when it is converted to size_t.
mlx4_core 0000:b1:00.0: Failed to initialize memory region table, aborting
mlx4_core: probe of 0000:b1:00.0 failed with error -12
Fix this issue by changing the left shifting operand from a signed literal to
an unsigned one.
Fixes: 225c7b1feef1 ("IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters")
Signed-off-by: Shung-Hsi Yu <shung-hsi.yu@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In RMII link mode it's required to set bit 15 IFCTL_A in MAC_SL MAC_CONTROL
register to enable support for 100Mbit link speed.
Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When multiple adapters are present in the system, pci hot-removing second
adapter leads to the following warning as both the adapters registered
thermal zone device with same thermal zone name/type.
Therefore, use unique thermal zone name during thermal zone device
initialization. Also mark thermal zone dev NULL once unregistered.
[ 414.370143] ------------[ cut here ]------------
[ 414.370944] sysfs group 'power' not found for kobject 'hwmon0'
[ 414.371747] WARNING: CPU: 9 PID: 2661 at fs/sysfs/group.c:281
sysfs_remove_group+0x76/0x80
[ 414.382550] CPU: 9 PID: 2661 Comm: bash Not tainted 5.8.0-rc6+ #33
[ 414.383593] Hardware name: Supermicro X10SRA-F/X10SRA-F, BIOS 2.0a 06/23/2016
[ 414.384669] RIP: 0010:sysfs_remove_group+0x76/0x80
[ 414.385738] Code: 48 89 df 5b 5d 41 5c e9 d8 b5 ff ff 48 89 df e8 60 b0 ff ff
eb cb 49 8b 14 24 48 8b 75 00 48 c7 c7 90 ae 13 bb e8 6a 27 d0 ff <0f> 0b 5b 5d
41 5c c3 0f 1f 00 0f 1f 44 00 00 48 85 f6 74 31 41 54
[ 414.388404] RSP: 0018:ffffa22bc080fcb0 EFLAGS: 00010286
[ 414.389638] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
[ 414.390829] RDX: 0000000000000001 RSI: ffff8ee2de3e9510 RDI: ffff8ee2de3e9510
[ 414.392064] RBP: ffffffffbaef2ee0 R08: 0000000000000000 R09: 0000000000000000
[ 414.393224] R10: 0000000000000000 R11: 000000002b30006c R12: ffff8ee260720008
[ 414.394388] R13: ffff8ee25e0a40e8 R14: ffffa22bc080ff08 R15: ffff8ee2c3be5020
[ 414.395661] FS: 00007fd2a7171740(0000) GS:ffff8ee2de200000(0000)
knlGS:0000000000000000
[ 414.396825] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 414.398011] CR2: 00007f178ffe5020 CR3: 000000084c5cc003 CR4: 00000000003606e0
[ 414.399172] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 414.400352] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 414.401473] Call Trace:
[ 414.402685] device_del+0x89/0x400
[ 414.403819] device_unregister+0x16/0x60
[ 414.405024] hwmon_device_unregister+0x44/0xa0
[ 414.406112] thermal_remove_hwmon_sysfs+0x196/0x200
[ 414.407256] thermal_zone_device_unregister+0x1b5/0x1f0
[ 414.408415] cxgb4_thermal_remove+0x3c/0x4f [cxgb4]
[ 414.409668] remove_one+0x212/0x290 [cxgb4]
[ 414.410875] pci_device_remove+0x36/0xb0
[ 414.412004] device_release_driver_internal+0xe2/0x1c0
[ 414.413276] pci_stop_bus_device+0x64/0x90
[ 414.414433] pci_stop_and_remove_bus_device_locked+0x16/0x30
[ 414.415609] remove_store+0x75/0x90
[ 414.416790] kernfs_fop_write+0x114/0x1b0
[ 414.417930] vfs_write+0xcf/0x210
[ 414.419059] ksys_write+0xa7/0xe0
[ 414.420120] do_syscall_64+0x4c/0xa0
[ 414.421278] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 414.422335] RIP: 0033:0x7fd2a686afd0
[ 414.423396] Code: Bad RIP value.
[ 414.424549] RSP: 002b:00007fffc1446148 EFLAGS: 00000246 ORIG_RAX:
0000000000000001
[ 414.425638] RAX: ffffffffffffffda RBX: 0000000000000002 RCX: 00007fd2a686afd0
[ 414.426830] RDX: 0000000000000002 RSI: 00007fd2a7196000 RDI: 0000000000000001
[ 414.427927] RBP: 00007fd2a7196000 R08: 000000000000000a R09: 00007fd2a7171740
[ 414.428923] R10: 00007fd2a7171740 R11: 0000000000000246 R12: 00007fd2a6b43400
[ 414.430082] R13: 0000000000000002 R14: 0000000000000001 R15: 0000000000000000
[ 414.431027] irq event stamp: 76300
[ 414.435678] ---[ end trace 13865acb4d5ab00f ]---
Fixes: b18719157762 ("cxgb4: Add thermal zone support")
Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This driver didn't set hard_header_len. This patch sets hard_header_len
for it according to its header_ops->create function.
This driver's header_ops->create function (cisco_hard_header) creates
a header of (struct hdlc_header), so hard_header_len should be set to
sizeof(struct hdlc_header).
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Acked-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Take the tx accounting out of the work_done calculation to
prevent a possible duplicate napi_schedule call when under
high Tx stress but low Rx traffic.
Fixes: b14e4e95f9ec ("ionic: tx separate servicing")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove 1000baseT_Half to advertise correct hardware capability in
phylink_validate() callback function.
Fixes: 38f790a80560 ("net: dsa: mt7530: Add support for port 5")
Signed-off-by: Landen Chao <landen.chao@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a bunch of issues in cpsw_ndo_vlan_rx_kill_vid()
- pm_runtime_get_sync() returns non zero value. This results in
non zero value return to caller which will be interpreted as error.
So overwrite ret with zero.
- If VID matches with port VLAN VID, then set error code.
- Currently when VLAN interface is deleted, all of the VLAN mc addresses
are removed from ALE table, however the return values from ale function
calls are not checked. These functions can return error code -ENOENT.
But that shouldn't happen in a normal case. So add error print to
catch the situations so that these can be investigated and addressed.
return zero in these cases as these are not real error case, but only
serve to catch ALE table update related issues and help address the
same in the driver.
Fixes: ed3525eda4c4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The buffer size is 2 Bytes and we expect to receive the same amount of
data. But sometimes we receive less data and run into uninit-was-stored
issue upon read. Hence modify the error check on the return value to match
with the buffer size as a prevention.
Reported-and-tested by: syzbot+a7e220df5a81d1ab400e@syzkaller.appspotmail.com
Signed-off-by: Himadri Pandya <himadrispandya@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Netpoll can try to poll napi as soon as napi_enable() is called.
It crashes trying to access a doorbell which is still NULL:
BUG: kernel NULL pointer dereference, address: 0000000000000000
CPU: 59 PID: 6039 Comm: ethtool Kdump: loaded Tainted: G S 5.9.0-rc1-00469-g5fd99b5d9950-dirty #26
RIP: 0010:bnxt_poll+0x121/0x1c0
Code: c4 20 44 89 e0 5b 5d 41 5c 41 5d 41 5e 41 5f c3 41 8b 86 a0 01 00 00 41 23 85 18 01 00 00 49 8b 96 a8 01 00 00 0d 00 00 00 24 <89> 02
41 f6 45 77 02 74 cb 49 8b ae d8 01 00 00 31 c0 c7 44 24 1a
netpoll_poll_dev+0xbd/0x1a0
__netpoll_send_skb+0x1b2/0x210
netpoll_send_udp+0x2c9/0x406
write_ext_msg+0x1d7/0x1f0
console_unlock+0x23c/0x520
vprintk_emit+0xe0/0x1d0
printk+0x58/0x6f
x86_vector_activate.cold+0xf/0x46
__irq_domain_activate_irq+0x50/0x80
__irq_domain_activate_irq+0x32/0x80
__irq_domain_activate_irq+0x32/0x80
irq_domain_activate_irq+0x25/0x40
__setup_irq+0x2d2/0x700
request_threaded_irq+0xfb/0x160
__bnxt_open_nic+0x3b1/0x750
bnxt_open_nic+0x19/0x30
ethtool_set_channels+0x1ac/0x220
dev_ethtool+0x11ba/0x2240
dev_ioctl+0x1cf/0x390
sock_do_ioctl+0x95/0x130
Reported-by: Rob Sherwood <rsher@fb.com>
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set the skb's network_header before it is passed to the underlying
Ethernet device for transmission.
This patch fixes the following issue:
When we use this driver with AF_PACKET sockets, there would be error
messages of:
protocol 0805 is buggy, dev (Ethernet interface name)
printed in the system "dmesg" log.
This is because skbs passed down to the Ethernet device for transmission
don't have their network_header properly set, and the dev_queue_xmit_nit
function in net/core/dev.c complains about this.
Reason of setting the network_header to this place (at the end of the
Ethernet header, and at the beginning of the Ethernet payload):
Because when this driver receives an skb from the Ethernet device, the
network_header is also set at this place.
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If USB_NET_CDC_NCM is y and USB_NET_CDCETHER is m, build fails:
drivers/net/usb/cdc_ncm.o:(.rodata+0x1d8): undefined reference to `usbnet_cdc_update_filter'
Select USB_NET_CDCETHER for USB_NET_CDC_NCM to fix this.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: e10dcb1b6ba7 ("net: cdc_ncm: hook into set_rx_mode to admit multicast traffic")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
when skb->encapsulation is 0, skb->ip_summed is CHECKSUM_PARTIAL
and it is udp packet, which has a dest port as the IANA assigned.
the hardware is expected to do the checksum offload, but the
hardware will not do the checksum offload when udp dest port is
6081.
This patch fixes it by doing the checksum in software.
Reported-by: Li Bing <libing@winhong.com>
Signed-off-by: Yi Li <yili@winhong.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The recent changes to support user-defined RSS map assume that RX
rings are always reserved and the default RSS map is set after the
RX rings are successfully reserved. If the firmware spec is older
than 1.6.1, no ring reservations are required and the default RSS
map is not setup at all. In another scenario where the fw Resource
Manager is older, RX rings are not reserved and we also end up with
no valid RSS map.
Fix both issues in bnxt_need_reserve_rings(). In both scenarios
described above, we don't need to reserve RX rings so we need to
call this new function bnxt_check_rss_map_no_rmgr() to setup the
default RSS map when needed.
Without valid RSS map, the NIC won't receive packets properly.
Fixes: 1667cbf6a4eb ("bnxt_en: Add logical RSS indirection table structure.")
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are no VF rings available during probe when the device is configured
using the Minimal-Static reservation strategy. In this case, the RSS
indirection table can only be initialized later, during bnxt_open_nic().
However, this was not happening because the rings will already have been
reserved via bnxt_init_dflt_ring_mode(), causing bnxt_need_reserve_rings()
to return false in bnxt_reserve_rings() and bypass the RSS table init.
Solve this by pushing the call to bnxt_set_dflt_rss_indir_tbl() into
__bnxt_reserve_rings(), which is common to both paths and is called
whenever ring configuration is changed. After doing this, the RSS table
init that must be called from bnxt_init_one() happens implicitly via
bnxt_set_default_rings(), necessitating doing the allocation earlier in
order to avoid a null pointer dereference.
Fixes: bd3191b5d87d ("bnxt_en: Implement ethtool -X to set indirection table.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Firmware returns RESOURCE_ACCESS_DENIED for HWRM_TEMP_MONITORY_QUERY for
VFs. This produces unpleasing error messages in the log when temp1_input
is queried via the hwmon sysfs interface from a VF.
The error is harmless and expected, so silence it and return unknown as
the value. Since the device temperature is not particularly sensitive
information, provide flexibility to change this policy in future by
silencing the error rather than avoiding the HWRM call entirely for VFs.
Fixes: cde49a42a9bb ("bnxt_en: Add hwmon sysfs support to read temperature")
Cc: Marc Smith <msmith626@gmail.com>
Reported-by: Marc Smith <msmith626@gmail.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bnxt_fw_reset_task() is run from a delayed workqueue. The current
code is not cancelling the workqueue in the driver's .remove()
method and it can potentially crash if the device is removed with
the workqueue still pending.
The fix is to clear the BNXT_STATE_IN_FW_RESET flag and then cancel
the delayed workqueue in bnxt_remove_one(). bnxt_queue_fw_reset_work()
also needs to check that this flag is set before scheduling. This
will guarantee that no rescheduling will be done after it is cancelled.
Fixes: 230d1f0de754 ("bnxt_en: Handle firmware reset.")
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a PCI error is detected the PCI state could be corrupt, save
the PCI state after initialization and restore it after the slot
reset.
Fixes: 6316ea6db93d ("bnxt_en: Enable AER support.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are returning the wrong count for ETH_SS_STATS in get_sset_count()
when XDP or TCs are enabled. In a recent commit, we got rid of
irrelevant counters when the ring is RX only or TX only, but we
did not make the proper adjustments for the count. As a result,
when we have XDP or TCs enabled, we are returning an excess count
because some of the rings are TX only. This causes ethtool -S to
display extra counters with no counter names.
Fix bnxt_get_num_ring_stats() by not assuming that all rings will
always have RX and TX counters in combined mode.
Fixes: 125592fbf467 ("bnxt_en: show only relevant ethtool stats for a TX or RX ring")
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If firmware goes into unstable state, HWRM_NVM_GET_DIR_INFO firmware
command may return zero dir entries. Return error in such case to
avoid zero length dma buffer request.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In rare conditions like two stage OS installation, the
ethtool's get_channels function may be called when the
device is in D3 state, leading to uncorrectable PCI error.
Check netif_running() first before making any query to FW
which involves writing to BAR.
Fixes: db4723b3cd2d ("bnxt_en: Check max_tx_scheduler_inputs value from firmware.")
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The RGMII control register at 0x32 indicates the states for the bits
RGMII_TX_CLK_DELAY and RGMII_RX_CLK_DELAY as follows:
RGMII Transmit/Receive Clock Delay
0x0 = RGMII transmit clock is shifted with respect to transmit/receive data.
0x1 = RGMII transmit clock is aligned with respect to transmit/receive data.
This commit fixes the inversed behavior of these bits
Fixes: 736b25afe284 ("net: dp83869: Add RGMII internal delay configuration")
Signed-off-by: Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At the time of do_rest, ibmvnic tries to re-initalize the tx_pools
and rx_pools to avoid re-allocating the long term buffer. However
there is a window inside do_reset that the tx_pools and
rx_pools were freed before re-initialized making it possible to deference
null pointers.
This patch fix this issue by always check the tx_pool
and rx_pool are not NULL after ibmvnic_login. If so, re-allocating
the pools. This will avoid getting into calling reset_tx/rx_pools with
NULL adapter tx_pools/rx_pools pointer. Also add null pointer check in
reset_tx_pools and reset_rx_pools to safe handle NULL pointer case.
Signed-off-by: Mingming Cao <mmc@linux.vnet.ibm.com>
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To flush the vid + mc entries from ALE, which is required when a VLAN
interface is removed, driver needs to call cpsw_ale_flush_multicast()
with ALE_PORT_HOST for port mask as these entries are added only for
host port. Without this, these entries remain in the ALE table even
after removing the VLAN interface. cpsw_ale_flush_multicast() calls
cpsw_ale_flush_mcast which expects a port mask to do the job.
Fixes: ed3525eda4c4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To flush the vid + mc entries from ALE, which is required when a VLAN
interface is removed, driver needs to call cpsw_ale_flush_multicast()
with ALE_PORT_HOST for port mask as these entries are added only for
host port. Without this, these entries remain in the ALE table even
after removing the VLAN interface. cpsw_ale_flush_multicast() calls
cpsw_ale_flush_mcast which expects a port mask to do the job.
Fixes: 15180eca569b ("net: ethernet: ti: cpsw: fix vlan mcast")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Every iteration of for_each_child_of_node() decrements
the reference count of the previous node, however when control
is transferred from the middle of the loop, as in the case of
a return or break or goto, there is no decrement thus ultimately
resulting in a memory leak.
Fix a potential memory leak in mt7530.c by inserting of_node_put()
before the break and return statements.
Issue found with Coccinelle.
Signed-off-by: Sumera Priyadarsini <sylphrenadin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During a dump, this attribute is essential, it enables the userspace to
know on which interface the context is linked to.
Fixes: 459aa660eb1d ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Tested-by: Gabriel Ganne <gabriel.ganne@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
check_fcs() was returning bool as 0/1, which was a sign that the sense
of the function was unclear: false was good, which doesn't really match
a name like 'check_$thing'. So rename it to ef100_has_fcs_error(), and
use proper booleans in the return statements.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Every iteration of for_each_available_child_of_node() decrements
the reference count of the previous node, however when control
is transferred from the middle of the loop, as in the case of
a return or break or goto, there is no decrement thus ultimately
resulting in a memory leak.
Fix a potential memory leak in felix.c by inserting of_node_put()
before the return statement.
Issue found with Coccinelle.
Signed-off-by: Sumera Priyadarsini <sylphrenadin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When devm_gpiod_get_optional() fails, bus should be
freed just like when of_mdiobus_register() fails.
Fixes: 1bddd96cba03d ("net: arc_emac: support the phy reset for emac driver")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clang warns:
drivers/net/dsa/sja1105/sja1105_main.c:3418:38: warning: address of
array 'match->compatible' will always evaluate to 'true'
[-Wpointer-bool-conversion]
for (match = sja1105_dt_ids; match->compatible; match++) {
~~~ ~~~~~~~^~~~~~~~~~
1 warning generated.
We should check the value of the first character in compatible to see if
it is empty or not. This matches how the rest of the tree iterates over
IDs.
Fixes: 0b0e299720bb ("net: dsa: sja1105: use detected device id instead of DT one on mismatch")
Link: https://github.com/ClangBuiltLinux/linux/issues/1139
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The underlying Ethernet device may request necessary tailroom to be
allocated by setting needed_tailroom. This driver should also set
needed_tailroom to request the tailroom needed by the underlying
Ethernet device to be allocated.
Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When this driver is built as a module, I cannot rmmod it after insmoding
it.
This is because that this driver calls ravb_mdio_init() at the time of
probe, and module->refcnt is incremented by alloc_mdio_bitbang() called
after that.
Therefore, even if ifup is not performed, the driver is in use and rmmod
cannot be performed.
$ lsmod
Module Size Used by
ravb 40960 1
$ rmmod ravb
rmmod: ERROR: Module ravb is in use
Call ravb_mdio_init() at open and free_mdio_bitbang() at close, thereby
rmmod is possible in the ifdown state.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Yuusuke Ashizuka <ashiduka@fujitsu.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When devm_kcalloc() fails, dev should be freed just
like what we've done in the subsequent error paths.
Fixes: 7b78be48a8eb6 ("net: systemport: Dynamically allocate number of TX rings")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
hns_nic_dev_probe allocates ndev, but not free it on
two error handling paths, which may lead to memleak.
Fixes: 63434888aaf1b ("net: hns: net: hns: enet adds support of acpi")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
Pull networking fixes from David Miller:
"Nothing earth shattering here, lots of small fixes (f.e. missing RCU
protection, bad ref counting, missing memset(), etc.) all over the
place:
1) Use get_file_rcu() in task_file iterator, from Yonghong Song.
2) There are two ways to set remote source MAC addresses in macvlan
driver, but only one of which validates things properly. Fix this.
From Alvin Šipraga.
3) Missing of_node_put() in gianfar probing, from Sumera
Priyadarsini.
4) Preserve device wanted feature bits across multiple netlink
ethtool requests, from Maxim Mikityanskiy.
5) Fix rcu_sched stall in task and task_file bpf iterators, from
Yonghong Song.
6) Avoid reset after device destroy in ena driver, from Shay
Agroskin.
7) Missing memset() in netlink policy export reallocation path, from
Johannes Berg.
8) Fix info leak in __smc_diag_dump(), from Peilin Ye.
9) Decapsulate ECN properly for ipv6 in ipv4 tunnels, from Mark
Tomlinson.
10) Fix number of data stream negotiation in SCTP, from David Laight.
11) Fix double free in connection tracker action module, from Alaa
Hleihel.
12) Don't allow empty NHA_GROUP attributes, from Nikolay Aleksandrov"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (46 commits)
net: nexthop: don't allow empty NHA_GROUP
bpf: Fix two typos in uapi/linux/bpf.h
net: dsa: b53: check for timeout
tipc: call rcu_read_lock() in tipc_aead_encrypt_done()
net/sched: act_ct: Fix skb double-free in tcf_ct_handle_fragments() error flow
net: sctp: Fix negotiation of the number of data streams.
dt-bindings: net: renesas, ether: Improve schema validation
gre6: Fix reception with IP6_TNL_F_RCV_DSCP_COPY
hv_netvsc: Fix the queue_mapping in netvsc_vf_xmit()
hv_netvsc: Remove "unlikely" from netvsc_select_queue
bpf: selftests: global_funcs: Check err_str before strstr
bpf: xdp: Fix XDP mode when no mode flags specified
selftests/bpf: Remove test_align leftovers
tools/resolve_btfids: Fix sections with wrong alignment
net/smc: Prevent kernel-infoleak in __smc_diag_dump()
sfc: fix build warnings on 32-bit
net: phy: mscc: Fix a couple of spelling mistakes "spcified" -> "specified"
libbpf: Fix map index used in error message
net: gemini: Fix missing free_netdev() in error path of gemini_ethernet_port_probe()
net: atlantic: Use readx_poll_timeout() for large timeout
...
|
|
Pull SCSI fixes from James Bottomley:
"23 fixes in 5 drivers (qla2xxx, ufs, scsi_debug, fcoe, zfcp). The bulk
of the changes are in qla2xxx and ufs and all are mostly small and
definitely don't impact the core"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (23 commits)
Revert "scsi: qla2xxx: Disable T10-DIF feature with FC-NVMe during probe"
Revert "scsi: qla2xxx: Fix crash on qla2x00_mailbox_command"
scsi: qla2xxx: Fix null pointer access during disconnect from subsystem
scsi: qla2xxx: Check if FW supports MQ before enabling
scsi: qla2xxx: Fix WARN_ON in qla_nvme_register_hba
scsi: qla2xxx: Allow ql2xextended_error_logging special value 1 to be set anytime
scsi: qla2xxx: Reduce noisy debug message
scsi: qla2xxx: Fix login timeout
scsi: qla2xxx: Indicate correct supported speeds for Mezz card
scsi: qla2xxx: Flush I/O on zone disable
scsi: qla2xxx: Flush all sessions on zone disable
scsi: qla2xxx: Use MBX_TOV_SECONDS for mailbox command timeout values
scsi: scsi_debug: Fix scp is NULL errors
scsi: zfcp: Fix use-after-free in request timeout handlers
scsi: ufs: No need to send Abort Task if the task in DB was cleared
scsi: ufs: Clean up completed request without interrupt notification
scsi: ufs: Improve interrupt handling for shared interrupts
scsi: ufs: Fix interrupt error message for shared interrupts
scsi: ufs-pci: Add quirk for broken auto-hibernate for Intel EHL
scsi: ufs-mediatek: Fix incorrect time to wait link status
...
|
|
clang static analysis reports this problem
b53_common.c:1583:13: warning: The left expression of the compound
assignment is an uninitialized value. The computed value will
also be garbage
ent.port &= ~BIT(port);
~~~~~~~~ ^
ent is set by a successful call to b53_arl_read(). Unsuccessful
calls are caught by an switch statement handling specific returns.
b32_arl_read() calls b53_arl_op_wait() which fails with the
unhandled -ETIMEDOUT.
So add -ETIMEDOUT to the switch statement. Because
b53_arl_op_wait() already prints out a message, do not add another
one.
Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Tom Rix <trix@redhat.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netvsc_vf_xmit() / dev_queue_xmit() will call VF NIC’s ndo_select_queue
or netdev_pick_tx() again. They will use skb_get_rx_queue() to get the
queue number, so the “skb->queue_mapping - 1” will be used. This may
cause the last queue of VF not been used.
Use skb_record_rx_queue() here, so that the skb_get_rx_queue() called
later will get the correct queue number, and VF will be able to use
all queues.
Fixes: b3bf5666a510 ("hv_netvsc: defer queue selection to VF")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Thomas Gleixner
Linus Torvalds
Michael Chan
Dan Murphy
Louis Peens
Xie He
Dan Carpenter
Denis Efremov
Shyam Sundar S K
Kamil Lorenc
Shung-Hsi Yu
Grygorii Strashko
Potnuri Bharat Teja
Shannon Nelson
Landen Chao
Murali Karicheri
Himadri Pandya
Jakub Kicinski
YueHaibing
Yi Li
Edwin Peer
Vasundhara Volam
Pavan Chebbi
Daniel Gorsulowski
Mingming Cao
Sumera Priyadarsini
Nicolas Dichtel
Edward Cree
Dinghao Liu
Nathan Chancellor
Yuusuke Ashizuka
Gustavo A. R. Silva
Tom Rix
Haiyang Zhang