| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Per PCIe r6.0, sec 5.2, a Link Down event can happen under any of the
following circumstances:
1. Fundamental/Hot reset
2. Link disable transmission by upstream component
3. Moving from L2/L3 to L0
In those cases, Link Down causes some non-sticky DWC registers to lose the
state (like REBAR, etc.), so drivers need to reinitialize them to function
properly once the link comes back again.
This is not a problem for drivers supporting PERST# IRQ, since they can
reinitialize the registers in the PERST# IRQ callback. But for the drivers
not supporting PERST#, there is no way they can reinitialize the registers
other than relying on Link Down IRQ received when the link goes down. So
add a DWC generic API dw_pcie_ep_linkdown() that reinitializes the
non-sticky registers and also notifies the EPF drivers about link going
down.
This API can also be used by the drivers supporting PERST# to handle the
scenario (2) mentioned above.
NOTE: For the sake of code organization, move the dw_pcie_ep_linkup()
definition just above dw_pcie_ep_linkdown().
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-8-22832d0d456f@linaro.org
Tested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: update spec citation]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
|
|
Instead of relying on the vendor specific implementations to send the
PME_Turn_Off message, introduce a generic way of sending the message using
the MSG TLP.
This is achieved by reserving a region for MSG TLP of size
'pci->region_align', at the end of the first IORESOURCE_MEM window of the
host bridge. And then sending the PME_Turn_Off message during system
suspend with the help of iATU.
The reason for reserving the MSG TLP region at the end of the
IORESOURCE_MEM is to avoid generating holes in between, because when the
region is allocated using allocate_resource(), memory will be allocated
from the start of the window. Later, if memory gets allocated for an
endpoint of size bigger than 'region_align', there will be a hole between
MSG TLP region and endpoint memory.
This generic implementation is optional for the glue drivers and can be
overridden by a custom 'pme_turn_off' callback.
Link: https://lore.kernel.org/linux-pci/20240418-pme_msg-v8-5-a54265c39742@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Add "code" and "routing" into struct dw_pcie_ob_atu_cfg for triggering
INTx IRQs by iATU in the PCIe endpoint mode in near the future.
PCIE_ATU_INHIBIT_PAYLOAD is set to issue TLP type of Msg instead of
MsgD. This implementation supports the data-less messages only for now.
Link: https://lore.kernel.org/linux-pci/20240418-pme_msg-v8-3-a54265c39742@nxp.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
|
|
This is a preparation before adding the Msg-type outbound iATU
mapping. The respective update will require two more arguments added
to __dw_pcie_prog_outbound_atu(). That will make the already
complicated function prototype even more hard to comprehend accepting
_eight_ arguments.
To prevent that and keep the code more-or-less readable, move all the
outbound iATU-related arguments to a new config structure: struct
dw_pcie_ob_atu_cfg, and pass a pointer to dw_pcie_prog_outbound_atu(). The
structure should be locally defined and populated with the outbound iATU
settings implied by the caller context.
As a result of this change there is no longer need in having the two
distinctive methods for the Host and Endpoint outbound iATU setups since
the code can directly call the dw_pcie_prog_outbound_atu() method with the
config structure populated, so drop dw_pcie_prog_ep_outbound_atu().
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240418-pme_msg-v8-2-a54265c39742@nxp.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
|
|
When PERST# assert and deassert happens on the PERST# supported platforms,
both iATU0 and iATU6 will map inbound window to BAR0. DMA will access the
area that was previously allocated (iATU0) for BAR0, instead of the new
area (iATU6) for BAR0.
Right now, this isn't an issue because both iATU0 and iATU6 should
translate inbound accesses to BAR0 to the same allocated memory area.
However, having two separate inbound mappings for the same BAR is a
disaster waiting to happen.
The mappings between PCI BAR and iATU inbound window are maintained in the
dw_pcie_ep::bar_to_atu[] array. While allocating a new inbound iATU map for
a BAR, dw_pcie_ep_inbound_atu() API checks for the availability of the
existing mapping in the array and if it is not found (i.e., value in the
array indexed by the BAR is found to be 0), it allocates a new map value
using find_first_zero_bit().
The issue is the existing logic failed to consider the fact that the map
value '0' is a valid value for BAR0, so find_first_zero_bit() will return
'0' as the map value for BAR0 (note that it returns the first zero bit
position).
Due to this, when PERST# assert + deassert happens on the PERST# supported
platforms, the inbound window allocation restarts from BAR0 and the
existing logic to find the BAR mapping will return '6' for BAR0 instead of
'0' due to the fact that it considers '0' as an invalid map value.
Fix this issue by always incrementing the map value before assigning to
bar_to_atu[] array and then decrementing it while fetching. This will make
sure that the map value '0' always represents the invalid mapping."
Fixes: 4284c88fff0e ("PCI: designware-ep: Allow pci_epc_set_bar() update inbound map address")
Closes: https://lore.kernel.org/linux-pci/ZXsRp+Lzg3x%2Fnhk3@x1-carbon/
Link: https://lore.kernel.org/linux-pci/20240412160841.925927-1-Frank.Li@nxp.com
Reported-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Tested-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
|
|
According to [1], msleep should be used for large sleeps, such as the
100-ish ms one in this function. Comply with the guide and use it.
[1] https://docs.kernel.org/timers/timers-howto.html
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240215-topic-pci_sleep-v2-1-79334884546b@linaro.org
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
The of_gpio.h legacy API is going to be removed. In preparation for that,
convert the driver to the agnostic API.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240506142142.4042810-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
|
|
Convert loops in kirin_pcie_parse_port() to use the _scoped() version of
for_each_available_child_of_node() so the refcounts of children are
implicitly decremented when the loop is exited.
No functional change intended here, but it will make future error exits
from these loops easier.
Link: https://lore.kernel.org/linux-pci/20240609-pcie-kirin-memleak-v1-1-62b45b879576@gmail.com
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: move to GPIO series to avoid bisection hole, commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
QCOM Resource Power Manager-hardened (RPMh) is a hardware block which
maintains hardware state of a regulator by performing max aggregation of
the requests made by all of the clients.
PCIe controller can operate on different RPMh performance state of power
domain based on the speed of the link. And this performance state varies
from target to target, like some controllers support GEN3 in NOM (Nominal)
voltage corner, while some other supports GEN3 in low SVS (static voltage
scaling).
The SoC can be more power efficient if we scale the performance state
based on the aggregate PCIe link bandwidth.
Add Operating Performance Points (OPP) support to vote for RPMh state based
on the aggregate link bandwidth.
OPP can handle ICC bw voting also, so move ICC bw voting through OPP
framework if OPP entries are present.
As we are moving ICC voting as part of OPP, don't initialize ICC if OPP
is supported.
Before PCIe link is initialized vote for highest OPP in the OPP table,
so that we are voting for maximum voltage corner for the link to come up
in maximum supported speed.
Link: https://lore.kernel.org/linux-pci/20240619-opp_support-v15-4-aa769a2173a3@quicinc.com
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: wrap comments to fit in 80 columns]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
To access the host controller registers of the host controller and the
endpoint BAR/config space, the CPU-PCIe ICC (interconnect) path should
be voted otherwise it may lead to NoC (Network on chip) timeout.
We are surviving because of other driver voting for this path.
As there is less access on this path compared to PCIe to mem path
add minimum vote i.e 1KBps bandwidth always which is sufficient enough
to keep the path active and is recommended by HW team.
During S2RAM (Suspend-to-RAM), the DBI access can happen very late (while
disabling the boot CPU). So do not disable the CPU-PCIe interconnect path
during S2RAM as that may lead to NoC error.
Link: https://lore.kernel.org/linux-pci/20240619-opp_support-v15-1-aa769a2173a3@quicinc.com
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
All EP specific resources are enabled during PERST# deassert. As a counter
operation, all resources should be disabled during PERST# assert. There is
no point in skipping that if the link was not enabled.
This will also result in enablement of the resources twice if PERST# got
deasserted again. So remove the check from qcom_pcie_perst_assert() and
disable all the resources unconditionally.
Fixes: f55fee56a631 ("PCI: qcom-ep: Add Qualcomm PCIe Endpoint controller driver")
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-1-22832d0d456f@linaro.org
Tested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
|
|
Due to some hardware changes, SA8775P has set the NO_SNOOP attribute
in its TLP for all the PCIe controllers. NO_SNOOP attribute when set,
the requester is indicating that no cache coherency issues exist for
the addressed memory on the host i.e., memory is not cached. But in
reality, requester cannot assume this unless there is a complete
control/visibility over the addressed memory on the host.
And worst case, if the memory is cached on the host, it may lead to
memory corruption issues. It should be noted that the caching of memory
on the host is not solely dependent on the NO_SNOOP attribute in TLP.
So to avoid the corruption, this patch overrides the NO_SNOOP attribute
by setting the PCIE_PARF_NO_SNOOP_OVERIDE register. This patch is not
needed for other upstream supported platforms since they do not set
NO_SNOOP attribute by default.
Link: https://lore.kernel.org/linux-pci/1710166298-27144-3-git-send-email-quic_msarkar@quicinc.com
Signed-off-by: Mrinmay Sarkar <quic_msarkar@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Due to some hardware changes, SA8775P has set the NO_SNOOP attribute
in its TLP for all the PCIe controllers. NO_SNOOP attribute when set,
the requester is indicating that no cache coherency issue exist for
the addressed memory on the endpoint i.e., memory is not cached. But
in reality, requester cannot assume this unless there is a complete
control/visibility over the addressed memory on the endpoint.
And worst case, if the memory is cached on the endpoint, it may lead to
memory corruption issues. It should be noted that the caching of memory
on the endpoint is not solely dependent on the NO_SNOOP attribute in TLP.
So to avoid the corruption, this patch overrides the NO_SNOOP attribute
by setting the PCIE_PARF_NO_SNOOP_OVERIDE register. This patch is not
needed for other upstream supported platforms since they do not set
NO_SNOOP attribute by default.
8775 has IP version 1.34.0 so introduce a new cfg(cfg_1_34_0) for this
platform. Assign override_no_snoop flag into struct qcom_pcie_cfg and
set it true in cfg_1_34_0 and enable cache snooping if this particular
flag is true.
Link: https://lore.kernel.org/linux-pci/1710166298-27144-2-git-send-email-quic_msarkar@quicinc.com
Signed-off-by: Mrinmay Sarkar <quic_msarkar@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: wrap comments to fit in 80 columns]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
When ARCH=x86, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/pci/controller/dwc/pci-exynos.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/pci/controller/pci-host-generic.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/pci/controller/pcie-altera.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/pci/controller/pcie-altera-msi.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/pci/controller/pcie-mediatek.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/pci/controller/pcie-mediatek-gen3.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/pci/controller/vmd.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/pci/controller/pcie-apple.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/pci/controller/pcie-mt7621.o
Add the missing MODULE_DESCRIPTION() macro.
[kwilczynski: update MODULE_DESCRIPTION() text, commit log]
Link: https://lore.kernel.org/linux-pci/20240626-md-drivers-pci-controller-v2-1-94c811db7a51@quicinc.com
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Nirmal Patel <nirmal.patel@linux.intel.com>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> # MT7621
|
|
As like the 'epc_init' event, that is used to signal the EPF drivers about
the EPC initialization, let's introduce 'epc_deinit' event that is used to
signal EPC deinitialization.
The EPC deinitialization applies only when any sort of fundamental reset
is supported by the endpoint controller as per the PCIe spec.
Reference: PCIe r6.0, sec 4.2.5.9.1 and 6.6.1.
Currently, some EPC drivers like pcie-qcom-ep and pcie-tegra194 support
PERST# as the fundamental reset. So the 'deinit' event will be notified to
the EPF drivers when PERST# assert happens in the above mentioned EPC
drivers.
The EPF drivers, on receiving the event through the epc_deinit() callback
should reset the EPF state machine and also cleanup any configuration that
got affected by the fundamental reset like BAR, DMA etc...
This change also warrants skipping the cleanups in unbind() if already done
in epc_deinit().
Link: https://lore.kernel.org/r/20240606-pci-deinit-v1-2-4395534520dc@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
|
|
The intent of the code snippet is to always return 0 for both
PCI_INTERRUPT_LINE and PCI_INTERRUPT_PIN.
The check misses PCI_INTERRUPT_PIN. This patch fixes that.
This is discovered by this call in VFIO:
pci_read_config_byte(vdev->pdev, PCI_INTERRUPT_PIN, &pin);
The old code does not set *val to 0 because it misses the check for
PCI_INTERRUPT_PIN. Garbage is returned in that case.
Fixes: 4daace0d8ce8 ("PCI: hv: Add paravirtual PCI front-end for Microsoft Hyper-V VMs")
Link: https://lore.kernel.org/linux-pci/20240701202606.129606-1-wei.liu@kernel.org
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Cc: stable@kernel.org
|
|
Add support for r8a779g0 (R-Car V4H).
This driver previously supported r8a779f0 (R-Car S4-8). PCIe features
of both r8a779f0 and r8a779g0 are almost all the same. For example:
- PCI Express Base Specification Revision 4.0
- Root complex mode and endpoint mode are supported
However, r8a779g0 requires specific firmware to be provided, to
initialize the PHY. Otherwise, the PCIe controller will not work.
[kwilczynski: drop the proprietary firmware conversion comment]
Link: https://lore.kernel.org/linux-pci/20240611125057.1232873-5-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Sequence for controlling the LTSSM state machine is going to change
for SoCs like r8a779f0. Move the LTSSM code to a new callback
ltssm_control() and populate it for each SoCs.
This also warrants the addition of new compatibles for r8a779g0 and
r8a779h0. But since they are already part of the DT binding, it won't
make any difference.
Link: https://lore.kernel.org/linux-pci/20240611125057.1232873-4-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
In order to support future SoCs such as r8a779g0 (R-Car V4H) and
r8a779h0 (R-Car V4M) that require different initialization settings,
introduce SoC specific driver data with the initial member being the
device mode.
No functional change.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240611125057.1232873-3-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
R-Car Gen4 PCIe controller needs to use the Synopsys-specific PCIe
configuration registers. So, add the macros.
Link: https://lore.kernel.org/linux-pci/20240611125057.1232873-2-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Errata #i2037 in AM65x/DRA80xM Processors Silicon Revision 1.0
(SPRZ452D_July 2018_Revised December 2019 [1]) mentions when an
inbound PCIe TLP spans more than two internal AXI 128-byte bursts,
the bus may corrupt the packet payload and the corrupt data may
cause associated applications or the processor to hang.
The workaround for Errata #i2037 is to limit the maximum read
request size and maximum payload size to 128 bytes. Add workaround
for Errata #i2037 here.
The errata and workaround is applicable only to AM65x SR 1.0 and
later versions of the silicon will have this fixed.
[1] -> https://www.ti.com/lit/er/sprz452i/sprz452i.pdf
Link: https://lore.kernel.org/linux-pci/16e1fcae-1ea7-46be-b157-096e05661b15@siemens.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Achal Verma <a-verma1@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
|
|
The struct mobiveil_rp_ops is not modified in this driver.
Thus, make this struct constant, which also moves data to a read-only
section decreasing object size and also improving overall security.
On a x86_64, with allmodconfig, as an example:
Before:
======
text data bss dec hex filename
4446 336 32 4814 12ce drivers/pci/controller/mobiveil/pcie-layerscape-gen4.o
After:
=====
text data bss dec hex filename
4454 328 32 4814 12ce drivers/pci/controller/mobiveil/pcie-layerscape-gen4.o
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/189fd881cc8fd80220e74e91820e12cf3a5be114.1719260294.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
'tegra_pcie_soc' has been unused since 56e15a238d92 ("PCI: tegra: Add
Tegra194 PCIe support"). Remove it.
Link: https://lore.kernel.org/r/20240527160118.37069-1-linux@treblig.org
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
|
|
Use preserve_config in place of checking for PCI_PROBE_ONLY flag to enable
support for "linux,pci-probe-only" on a per host bridge basis.
This also obviates the use of adding PCI_REASSIGN_ALL_BUS flag if
!PCI_PROBE_ONLY, as pci_assign_unassigned_root_bus_resources() takes care
of reassigning the resources that are not already claimed.
Link: https://lore.kernel.org/r/20240508174138.3630283-5-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Tegra194 and Tegra234 PCIe EP controllers have 64K alignment restriction
for the inbound ATU. Set the endpoint inbound ATU alignment to 64kB in the
Tegra194 PCIe driver.
Fixes: c57247f940e8 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Suggested-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Link: https://lore.kernel.org/linux-pci/20240508092207.337063-1-jonathanh@nvidia.com
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
|
|
Avoid large backtrace, it is sufficient to warn the user that there has
been a link problem. Either the link has failed and the system is in need
of maintenance, or the link continues to work and user has been informed.
The message from the warning can be looked up in the sources.
This makes an actual link issue less verbose.
First of all, this controller has a limitation in that the controller
driver has to assist the hardware with transition to L1 link state by
writing L1IATN to PMCTRL register, the L1 and L0 link state switching
is not fully automatic on this controller.
In case of an ASMedia ASM1062 PCIe SATA controller which does not support
ASPM, on entry to suspend or during platform pm_test, the SATA controller
enters D3hot state and the link enters L1 state. If the SATA controller
wakes up before rcar_pcie_wakeup() was called and returns to D0, the link
returns to L0 before the controller driver even started its transition to
L1 link state. At this point, the SATA controller did send an PM_ENTER_L1
DLLP to the PCIe controller and the PCIe controller received it, and the
PCIe controller did set PMSR PMEL1RX bit.
Once rcar_pcie_wakeup() is called, if the link is already back in L0 state
and PMEL1RX bit is set, the controller driver has no way to determine if
it should perform the link transition to L1 state, or treat the link as if
it is in L0 state. Currently the driver attempts to perform the transition
to L1 link state unconditionally, which in this specific case fails with a
PMSR L1FAEG poll timeout, however the link still works as it is already
back in L0 state.
Reduce this warning verbosity. In case the link is really broken, the
rcar_pcie_config_access() would fail, otherwise it will succeed and any
system with this controller and ASM1062 can suspend without generating
a backtrace.
Fixes: 84b576146294 ("PCI: rcar: Finish transition to L1 state in rcar_pcie_config_access()")
Link: https://lore.kernel.org/linux-pci/20240511235513.77301-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Add StarFive JH7110 SoC PCIe controller platform driver code, JH7110
with PLDA host PCIe core.
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-22-minda.chen@starfivetech.com
Co-developed-by: Kevin Xie <kevin.xie@starfivetech.com>
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mason Huo <mason.huo@starfivetech.com>
|
|
plda_pcie_setup_iomems() needs the bridge->windows list from struct
pci_host_bridge and is currently used only by pcie-microchip-host.c. This
driver uses pci_host_common_probe(), which sets a pci_host_bridge as the
drvdata, so plda_pcie_setup_iomems() used platform_get_drvdata() to find
the pci_host_bridge.
But we also want to use plda_pcie_setup_iomems() in the new pcie-starfive.c
driver, which does not use pci_host_common_probe() and will have struct
starfive_jh7110_pcie as its drvdata, so pass the pci_host_bridge directly
to plda_pcie_setup_iomems() so it doesn't need platform_get_drvdata() to
find it.
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-9-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log, reorder to where this is needed]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Add PLDA host plda_pcie_host_init()/plda_pcie_host_deinit() and map bus
function so vendors can use it to init PLDA PCIe host core.
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-19-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mason Huo <mason.huo@starfivetech.com>
|
|
PLDA DMA interrupts are not all implemented, and the non-implemented
interrupts should be masked. Add a bitmap field to mask the non-implemented
interrupts.
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-18-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Move IRQ related functions to common file pcie-plda-host.c
The re-use code including MSI, INTx, event interrupts and IRQ init
functions.
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-17-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
|
|
As the PLDA DT binding doc (Documentation/devicetree/bindings/pci/
plda,xpressrich3-axi-common.yaml) shows, PLDA PCIe contains an interrupt
controller.
Microchip PolarFire PCIe event IRQs include PLDA interrupts and PolarFire
additional interrupts. The interrupt irqchip ops includes ack/mask/unmask
interrupt ops, which will write correct registers. Microchip PolarFire
PCIe additional interrupts require to write PolarFire SoC self-defined
registers. So Microchip PCIe event irqchip ops can not be re-used.
Microchip PolarFire PCIe additional interrupts (defined in
drivers/pci/controller/plda/pcie-microchip-host.c):
EVENT_PCIE_L2_EXIT
EVENT_PCIE_HOTRST_EXIT
EVENT_PCIE_DLUP_EXIT
EVENT_SEC_TX_RAM_SEC_ERR
EVENT_SEC_RX_RAM_SEC_ERR
...
To support PLDA its own event IRQ process, implements PLDA irqchip ops and
add event irqchip field to struct pcie_plda_rp.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-16-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
|
|
As PLDA DT binding doc (Documentation/devicetree/bindings/pci/
plda,xpressrich3-axi-common.yaml) showed, PLDA PCIe contains an interrupt
controller.
PolarFire implements its own PCIe interrupts, additional to the regular
PCIe interrupts, due to lack of an MSI controller, so the interrupt to
event number mapping is different to the PLDA regular interrupts,
necessitating a custom get_events() implementation.
Microchip PolarFire PCIe additional interrupts (defined in
drivers/pci/controller/plda/pcie-microchip-host.c):
EVENT_PCIE_L2_EXIT
EVENT_PCIE_HOTRST_EXIT
EVENT_PCIE_DLUP_EXIT
EVENT_SEC_TX_RAM_SEC_ERR
EVENT_SEC_RX_RAM_SEC_ERR
...
plda_get_events() adds interrupt register to PLDA event num mapping codes.
All the PLDA interrupts can be seen in new added graph.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-15-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
|
|
The INTx and MSI interrupt event num is different across platforms, so
add two event num fields in struct plda_event.
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-14-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
|
|
As the PLDA DT binding doc (Documentation/devicetree/bindings/pci/
plda,xpressrich3-axi-common.yaml) shows, the PLDA IP contains an interrupt
controller. Microchip PolarFire add some interrupts based on PLDA interrupt
controller.
The Microchip PolarFire PCIe additional interrupts (defined in
drivers/pci/controller/plda/pcie-microchip-host.c):
EVENT_PCIE_L2_EXIT
EVENT_PCIE_HOTRST_EXIT
EVENT_PCIE_DLUP_EXIT
EVENT_SEC_TX_RAM_SEC_ERR
EVENT_SEC_RX_RAM_SEC_ERR
...
Both event_cause[] and mc_event_handler() contain additional interrupt
symbol names; these can not be re-used. Add a new plda_event_handler()
function, which implements PLDA interrupt defalt handler, and add a
request_event_irq() callback function for Microchip PolarFire additional
interrupts.
[kwilczynski, bhelgaas: commit log]
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-13-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
|
|
The number of events is different across platforms. In order to share
interrupt processing code, add a variable that defines the number of
events so that it can be set per-platform instead of hardcoding it.
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-12-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Rename mc_* to plda_* for IRQ functions and related IRQ domain ops data
instances.
MSI, INTx interrupt code and IRQ init code can all be re-used.
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-11-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Move plda_pcie_setup_window() and plda_pcie_setup_iomems() to
pcie-plda-host.c so they can be shared by all PLDA-based drivers.
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-10-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Rename mc_pcie_setup_window() to plda_pcie_setup_window() and
mc_pcie_setup_windows() to plda_pcie_setup_iomems() so they can be shared
by all PLDA-based drivers.
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-8-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Move the PLDA generic data structures to a header file so they can be
re-used by all PLDA-based drivers.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-7-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Rename struct mc_msi to plda_msi and move most of struct mc_pcie to a new
struct plda_pcie_rp so they can be shared by all PLDA-based drivers.
The axi_base_addr field remains in struct mc_pcie since it's
Microchip-specific data.
The event interrupt code is still using struct mc_pcie because the event
interrupt code can not be re-used.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-6-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Bridge address base is common PLDA field, add this to struct mc_pcie first.
INTx and MSI interrupt code will be changed to common code, so get the
bridge base address from port->bridge_addr instead of axi_base_addr.
The axi_base_addr is Microchip-specific data.
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-5-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Move PLDA PCIe host controller IP registers macros to pcie-plda.h,
including bridge registers and PLDA IRQ event number.
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-4-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Since Microchip PolarFire PCIe host is PLDA XpressRich IP, move to PLDA
directory. Prepare for refactoring the codes.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-3-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
|
|
If IORESOURCE_MEM is not provided in Device Tree due to
any error, resource_list_first_type() will return NULL and
pci_parse_request_of_pci_ranges() will just emit a warning.
This will cause a NULL pointer dereference. Fix this bug by adding NULL
return check.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 0f71c60ffd26 ("PCI: dwc: Remove storing of PCI resources")
Link: https://lore.kernel.org/linux-pci/20240505061517.11527-1-amishin@t-argos.ru
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
After 6ab15b5e7057 ("PCI: dwc: keystone: Convert .scan_bus() callback to
use add_bus"), ks_pcie_v3_65_add_bus() enabled BAR 0 for both v3.65a and
v4.90a devices. On the AM654x SoC, which uses v4.90a, enabling BAR 0
causes Completion Timeouts when setting up MSI-X. These timeouts delay
boot of the AM654x by about 45 seconds.
Move the BAR 0 initialization to ks_pcie_msi_host_init(), which is only
used for v3.65a devices, and remove ks_pcie_v3_65_add_bus().
[bhelgaas: commit log]
Fixes: 6ab15b5e7057 ("PCI: dwc: keystone: Convert .scan_bus() callback to use add_bus")
Link: https://lore.kernel.org/linux-pci/20240328085041.2916899-3-s-vadapalli@ti.com
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Suggested-by: Niklas Cassel <cassel@kernel.org>
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
|
|
Relocate ks_pcie_set_dbi_mode() and ks_pcie_clear_dbi_mode() to avoid
forward declaration in a subsequent patch. No functional change intended.
Link: https://lore.kernel.org/linux-pci/20240328085041.2916899-2-s-vadapalli@ti.com
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The of_gpio.h legacy API is going to be removed. In preparation for that,
convert the driver to the agnostic API.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240506142142.4042810-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
The of_gpio.h API is deprecated and subject to removal. The driver doesn't
use it, so simply remove the unused header.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240506142142.4042810-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
The of_gpio.h API is deprecated and subject to removal. The driver doesn't
use it, so simply remove the unused header.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240506142142.4042810-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
Manivannan Sadhasivam
Frank Li
Yoshihiro Shimoda
Konrad Dybcio
Andy Shevchenko
Javier Carrasco
Krishna chaitanya chundru
Mrinmay Sarkar
Jeff Johnson
Wei Liu
Kishon Vijay Abraham I
Christophe JAILLET
Dr. David Alan Gilbert
Vidya Sagar
Jon Hunter
Marek Vasut
Minda Chen
Aleksandr Mishin
Siddharth Vadapalli