| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This driver supports handling 2 BlueField power states controlled by
GPIO interrupts:
1) chip reset and
2) low power mode
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The only way to reset the BeagleV Starlight v0.9 board[1] properly is to
tell the PMIC to reset itself which will then assert the external reset
lines of the SoC, USB hub and ethernet phy.
This adds a driver to register a reset handler to do just that.
[1] https://github.com/beagleboard/beaglev-starlight
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The zte zx platform is getting removed, so this driver is no
longer needed.
Cc: Jun Nie <jun.nie@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
This driver provides poweroff and reboot support for a system through
the ATC2603C and ATC2609A chip variants of the Actions Semi ATC260x
family of PMICs.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
This driver registers a pm_power_off function to turn off the board
by force-disabling a devicetree-defined regulator.
Signed-off-by: Michael Klein <michael@fossekall.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
To add support for Sparx5, the dependency on MSCC_OCELOT was removed.
However, this increases exposure of the driver question not only to
Sparx5 platforms, but to everyone. Hence re-add the dependency on
MSCC_OCELOT, and extend it with ARCH_SPARX5, to prevent asking the user
about this driver when configuring a kernel without Ocelot and Sparx5
support.
Fixes: ec871696b7776767 ("power: reset: ocelot: Add support for Sparx5")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
This adds reset support for Sparx5 in the ocelot-reset driver.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Some Buffalo LinkStations perform the power off operation, at restart
time, depending on the state of an output pin (LED2/INTn) at the ethernet
PHY. This pin is also used to wake the machine when a WoL packet is
received by the PHY.
The driver is required by the Buffalo LinkStation LS421DE (ARM MVEBU),
and other models. Without it, the board remains forever halted if a
power off command is executed, unless the PSU is disconnected and
connected again.
Add the driver to provide the power off function and also make the WoL
feature to be available.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Pull power supply and reset updates from Sebastian Reichel:
"This time there are lots of changes. Quite a few changes to the core,
lots of driver changes and one change to kobject core (with Ack from
Greg).
Summary:
kobject:
- Increase number of allowed uevent variables
power-supply core:
- Add power-supply type in uevent
- Cleanup property handling in core
- Make property and usb_type pointers const
- Convert core power-supply DT binding to YAML
- Cleanup HWMON code
- Add new health status "calibration required"
- Add new properties for manufacture date and capacity error margin
battery drivers:
- new cw2015 battery driver used by pine64 Pinebook Pro laptop
- axp22: blacklist on Meegopad T02
- sc27xx: support current/voltage reading
- max17042: support time-to-empty reading
- simple-battery: add more battery parameters
- bq27xxx: convert DT binding document to YAML
- sbs-battery: add TI BQ20Z65 support, fix technology property,
convert DT binding to YAML, add option to disable charger
broadcasts, add new properties: manufacture date, capacity
error margin, average current, charge current and voltage and
support calibration required health status
- misc fixes
charger drivers:
- bq25890: cleanup, implement charge type, precharge current and
input current limiting properties
- bd70528: use new linear range helper library
- bd99954: new charger driver
- mp2629: new charger driver
- misc fixes
reboot drivers:
- oxnas-restart: introduce new driver
- syscon-reboot: convert DT binding to YAML, add parent syscon device
support
- misc fixes"
* tag 'for-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (85 commits)
power: supply: cw2015: Attach OF ID table to the driver
power: reset: gpio-poweroff: add missing '\n' in dev_err()
Revert "power: supply: sbs-battery: simplify read_read_string_data"
Revert "power: supply: sbs-battery: add PEC support"
dt-bindings: power: sbs-battery: Convert to yaml
power: supply: sbs-battery: constify power-supply property array
power: supply: sbs-battery: switch to i2c's probe_new
power: supply: sbs-battery: switch from of_property_* to device_property_*
power: supply: sbs-battery: add ability to disable charger broadcasts
power: supply: sbs-battery: fix idle battery status
power: supply: sbs-battery: add POWER_SUPPLY_HEALTH_CALIBRATION_REQUIRED support
power: supply: sbs-battery: add MANUFACTURE_DATE support
power: supply: sbs-battery: add POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT/VOLTAGE_MAX support
power: supply: sbs-battery: Improve POWER_SUPPLY_PROP_TECHNOLOGY support
power: supply: sbs-battery: add POWER_SUPPLY_PROP_CURRENT_AVG support
power: supply: sbs-battery: add PEC support
power: supply: sbs-battery: simplify read_read_string_data
power: supply: sbs-battery: add POWER_SUPPLY_PROP_CAPACITY_ERROR_MARGIN support
power: supply: sbs-battery: Add TI BQ20Z65 support
power: supply: core: add POWER_SUPPLY_HEALTH_CALIBRATION_REQUIRED
...
|
|
An allmodconfig kernel makes CONFIG_VEXPRESS_CONFIG a module and
CONFIG_POWER_RESET_VEXPRESS builtin. That makes us see this build
error:
aarch64-linux-gnu-ld: drivers/power/reset/vexpress-poweroff.o: in function `vexpress_reset_probe':
../drivers/power/reset/vexpress-poweroff.c:119: undefined reference to `devm_regmap_init_vexpress_config'
../drivers/power/reset/vexpress-poweroff.c:119:(.text+0x48c): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol
`devm_regmap_init_vexpress_config'
make[1]: *** [/srv/src/kernel/next/Makefile:1126: vmlinux] Error 1
Rework so that POWER_RESET_VEXPRESS depends on 'VEXPRESS_CONFIG=y'.
Link: https://lore.kernel.org/r/20200527112608.3886105-5-anders.roxell@linaro.org
Fixes: d06cfe3f123c ("bus: vexpress-config: Merge vexpress-syscfg into vexpress-config")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add reboot handler for Oxford OX820 chips as reboot currenly hangs on
those boards. Code is based on ox820_assert_system_reset() found in
https://github.com/kref/linux-oxnas.git in
arch/arm/mach-oxnas/mach-ox820.c line 181.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Change the config to 'tristate' and use module_platform_driver() to
allow the SC27XX poweroff driver building into a module, as well as
adding some mudule information.
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Pull ARM SoC platform updates from Olof Johansson:
"Most of these are smaller fixes that have accrued, and some continued
cleanup of OMAP platforms towards shared frameworks.
One new SoC from Atmel/Microchip: sam9x60"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (35 commits)
ARM: OMAP2+: Fix undefined reference to omap_secure_init
ARM: s3c64xx: Drop unneeded select of TIMER_OF
ARM: exynos: Drop unneeded select of MIGHT_HAVE_CACHE_L2X0
ARM: s3c24xx: Switch to atomic pwm API in rx1950
ARM: OMAP2+: sleep43xx: Call secure suspend/resume handlers
ARM: OMAP2+: Use ARM SMC Calling Convention when OP-TEE is available
ARM: OMAP2+: Introduce check for OP-TEE in omap_secure_init()
ARM: OMAP2+: Add omap_secure_init callback hook for secure initialization
ARM: at91: Documentation: add sam9x60 product and datasheet
ARM: at91: pm: use of_device_id array to find the proper shdwc node
ARM: at91: pm: use SAM9X60 PMC's compatible
ARM: imx: only select ARM_ERRATA_814220 for ARMv7-A
ARM: zynq: use physical cpuid in zynq_slcr_cpu_stop/start
ARM: tegra: Use clk_m CPU on Tegra124 LP1 resume
ARM: tegra: Modify reshift divider during LP1
ARM: tegra: Enable PLLP bypass during Tegra124 LP1
ARM: samsung: Rename Samsung and Exynos to lowercase
ARM: exynos: Correct the help text for platform Kconfig option
ARM: bcm: Select ARM_AMBA for ARCH_BRCMSTB
ARM: brcmstb: Add debug UART entry for 7216
...
|
|
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Select POWER_RESET_AT91_SAMA5D2_SHDWC for SAM9X60 SoC.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1575035505-6310-7-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Select POWER_RESET_AT91_RESET for SAM9X60 SoC.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/1575035505-6310-6-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
add poweroff driver for mt6323 and make Makefile and Kconfig-Entries
Suggested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Josef Friedl <josef.friedl@speed.at>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Pull power supply and reset updates from Sebastian Reichel:
"Core:
- add HWMON compat layer
- new properties:
- input power limit
- input voltage limit
Drivers:
- qcom-pon: add gen2 support
- new driver for storing reboot move in NVMEM
- new driver for Wilco EC charger configuration
- simplify getting the adapter of a client"
* tag 'for-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
power: reset: nvmem-reboot-mode: add CONFIG_OF dependency
power_supply: wilco_ec: Add charging config driver
power: supply: cros: allow to set input voltage and current limit
power: supply: add input power and voltage limit properties
power: supply: fix semicolon.cocci warnings
power: reset: nvmem-reboot-mode: use NVMEM as reboot mode write interface
dt-bindings: power: reset: add document for NVMEM based reboot-mode
reset: qcom-pon: Add support for gen2 pon
dt-bindings: power: reset: qcom: Add qcom,pm8998-pon compatibility line
power: supply: Add HWMON compatibility layer
power: supply: sbs-manager: simplify getting the adapter of a client
power: supply: rt9455_charger: simplify getting the adapter of a client
power: supply: rt5033_battery: simplify getting the adapter of a client
power: supply: max17042_battery: simplify getting the adapter of a client
power: supply: max17040_battery: simplify getting the adapter of a client
power: supply: max14656_charger_detector: simplify getting the adapter of a client
power: supply: bq25890_charger: simplify getting the adapter of a client
power: supply: bq24257_charger: simplify getting the adapter of a client
power: supply: bq24190_charger: simplify getting the adapter of a client
|
|
Without CONFIG_OF, we get a build failure in the reboot-mode
implementation:
drivers/power/reset/reboot-mode.c: In function 'reboot_mode_register':
drivers/power/reset/reboot-mode.c:72:2: error: implicit declaration of function 'for_each_property_of_node'; did you mean 'for_each_child_of_node'? [-Werror=implicit-function-declaration]
for_each_property_of_node(np, prop) {
Add a Kconfig dependency like we have for the other users of
CONFIG_REBOOT_MODE.
Fixes: 7a78a7f7695b ("power: reset: nvmem-reboot-mode: use NVMEM as reboot mode write interface")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add a new reboot mode write interface that is using an NVMEM cell
to store the reboot mode magic.
Signed-off-by: Nandor Han <nandor.han@vaisala.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support Qualcomm PM8xxx PON which is responsible for reboot
mode support.
Co-developed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
|
|
On Spreadtrum platform, we need power off system through external SC27xx
series PMICs including the SC2720, SC2721, SC2723, SC2730 and SC2731 chips.
Thus this patch adds SC27xx series PMICs power-off support.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
|
|
The Microsemi Ocelot SoC has a register allowing to reset the MIPS core.
Unfortunately, the syscon-reboot driver can't be used directly (but almost)
as the reset control may be disabled using another register.
Cc: linux-pm@vger.kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
|
|
There's no user of it in kernel now and it basically functions the same
as the generic syscon-poweroff.c to which we have already switched.
So let's remove it.
Cc: Robin Gong <yibin.gong@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
|
|
On Broadcom MIPS STB platforms, BMIPS_GENERIC is the Kconfig symbol that
is used, make this reboot driver default to that value to make sure we
can reboot a system properly.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Since commit 37eb56dc79a8 ("arm64: Add Broadcom Set Top Box Kconfig
entry point") we have ARCH_BRCMSTB also visible on ARM64 platform, yet
this reboot driver was not selectable, so fix that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
The Gemini (SL3516) SoC has a special power controller block
that only deal with shutting down the system.
If you do not register a driver and activate the block, the
power button on the systems utilizing this SoC will do an
uncontrolled power cut, which is why it is important to have
a special poweroff driver.
The most basic functionality is to just shut down the system
by writing a special bit in the control register after the
system has reached pm_poweroff.
It also handles the poweroff from a button or other sources:
When the poweroff button is pressed, or a signal is sent to
poweroff from an infrared remote control, or when the RTC
fires a special alarm (!) the system emits an interrupt.
At this point, Linux must acknowledge the interrupt and
proceed to do an orderly shutdown of the system.
After adding this driver, pressing the poweroff button gives
this dmesg:
root@gemini:/
root@gemini:/ gemini-poweroff 4b000000.power-controller:
poweroff button pressed
calling shutdown scripts..
setting /dev/rtc0 from system time
unmounting file systems...
umount: tmpfs busy - remounted read-only
umount: can't unmount /: Invalid argument
The system is going down NOW!
Sent SIGTERM to all processes
Sent SIGKILL to all processes
Requesting system poweroff
uhci_hcd 0000:00:09.1: HCRESET not completed yet!
uhci_hcd 0000:00:09.0: HCRESET not completed yet!
reboot: Power down
gemini-poweroff 4b000000.power-controller: Gemini power off
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-pm@vger.kernel.org
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
LPDDR memories can only handle up to 400 uncontrolled power off. Ensure the
proper power off sequence is used before shutting down the platform.
Cc: <stable@vger.kernel.org> # 4.4+
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Add a driver which allows powering off the system via an Intel PIIX4
southbridge, by entering the PIIX4 SOff state. This is useful on the
MIPS Malta development board, where it will power down the FPGA based
board until its ON/NMI button is pressed, or the QEMU implementation of
the MIPS Malta board where it will cause QEMU to exit.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
commit 4fcd504edbf7 ("power: reset: add reboot mode driver") uses api from
syscon, and syscon uses ioremap/iounmap which depends on HAS_IOMEM, so
let's depend on MFD_SYSCON instead of selecting it directly to avoid the
um-allyesconfig like build error on archs that without iomem:
drivers/mfd/syscon.c: In function 'of_syscon_register':
drivers/mfd/syscon.c:67:9: error: implicit declaration of function 'ioremap' [-Werror=implicit-function-declaration]
base = ioremap(res.start, resource_size(&res));
^
drivers/mfd/syscon.c:67:7: warning: assignment makes pointer from integer without a cast [-Wint-conversion]
base = ioremap(res.start, resource_size(&res));
^
drivers/mfd/syscon.c:109:2: error: implicit declaration of function 'iounmap' [-Werror=implicit-function-declaration]
iounmap(base);
^
Reported-by: Kbuild test robot <fengguang.wu@intel.com>
Fixes: 4fcd504edbf7("power: reset: add reboot mode driver")
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we
merge through arm-soc for historical reasons, is also sizable this
time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (100 commits)
ARM: ux500: consolidate base platform files
ARM: ux500: move soc_id driver to drivers/soc
ARM: ux500: call ux500_setup_id later
ARM: ux500: consolidate soc_device code in id.c
ARM: ux500: remove cpu_is_u* helpers
ARM: ux500: use CLK_OF_DECLARE()
ARM: ux500: move l2x0 init to .init_irq
mfd: db8500 stop passing around platform data
ASoC: ab8500-codec: remove platform data based probe
ARM: ux500: move ab8500_regulator_plat_data into driver
ARM: ux500: remove unused regulator data
soc: raspberrypi-power: add CONFIG_OF dependency
firmware: scpi: add CONFIG_OF dependency
video: clps711x-fb: Changing the compatibility string to match with the smallest supported chip
input: clps711x-keypad: Changing the compatibility string to match with the smallest supported chip
pwm: clps711x: Changing the compatibility string to match with the smallest supported chip
serial: clps711x: Changing the compatibility string to match with the smallest supported chip
irqchip: clps711x: Changing the compatibility string to match with the smallest supported chip
clocksource: clps711x: Changing the compatibility string to match with the smallest supported chip
clk: clps711x: Changing the compatibility string to match with the smallest supported chip
...
|
|
This driver parses the reboot commands like "reboot bootloader"
and "reboot recovery" to get a boot mode described in the
device tree , then call the write interfae to store the boot
mode in some place like special register or sram, which can
be read by the bootloader after system reboot, then the bootloader
can take different action according to the mode stored.
This is commonly used on Android based devices, in order to
reboot the device into fastboot or recovery mode.
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
Tested-by: John Stultz <john.stultz@linaro.org>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
This driver supports reset on both BCM21664 and BCM23550.
Code is being moved from arch/arm/mach-bcm/board_bcm21664.c
Signed-off-by: Chris Brand <chris.brand@broadcom.com>
Acked-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Enable the COMPILE_TEST to get build coverage, except on platforms
!HAS_IOMEM (required by selected MFD_SYSCON).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Sama5d2 SoC has a completely new shutdown controller with new features and
register layout. It thus makes sense to add a new driver for this new
peripheral.
This driver is Device Tree only and handles events from the wake-up pin and
the RTC.
As the register layout may change in the future, so some values are encoded
in a configuration structure.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Not every arch has io memory.
So, unbreak the build by fixing the dependencies.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
It was not possible to compile at91-poweroff as a module. Implement
.remove() to allow it. Also switch to module_platform_driver_probe() as it
is not hotpluggable.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
It was not possible to compile at91-reset as a module. Implement .remove()
to allow it. Also switch to module_platform_driver_probe() as it is not
hotpluggable.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Register with kernel restart handler instead of setting arm_pm_restart
directly.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
The Broadcom STB reboot driver depends on MFD_SYSCON, it uses
syscon_regmap_lookup_by_phandle() which will not lookup syscon phandles
if MFD_SYSCON is disabled, and instead will return -ENOSYS since it is
turned into an inline stub.
Fixes: 030494e75064c ("power: reset: Add reboot driver for brcmstb")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Add a generic SYSCON register mapped poweroff mechanism.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Fixes:
drivers/power/reset/rmobile-reset.c: In function ‘rmobile_reset_probe’:
drivers/power/reset/rmobile-reset.c:61:2: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
iounmap(sysc_base2);
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
This driver is now arm specific anymore, so there is no need to include
an arm specific include file. Also drop unnecessary depencency on ARM
from Kconfig.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
The st-poweroff driver does not really power off the system
but resets it, so Kconfig should not claim that the driver
would handle power-off.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
sun6i restart is now handled by its watchdog driver directly,
so this driver is no longer needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Now that the driver doesn't use any ARM-specific headers, it is safe
to build on MIPS or with COMPILE_TEST.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Add a reset driver for Renesas R-Mobile and SH-Mobile SoCs. It registers
a restart handler to trigger a soft power-on reset through the R-Mobile
System Controller.
The priority of this restart handler is 192, to allow a watchdog driver
to use priority 128.
Note that we do not use syscon-reboot, as the HPB (Peripheral Bus
Bridge) semaphore should be acquired on systems where both the ARM and
SH core are in use. The driver can be extended later to support this,
when needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
This driver register pm_power_off with snvs power off function. If
your boards NOT use PMIC_ON_REQ to turn on/off external pmic, or use
other pin to do, please disable the driver in dts, otherwise, your
pm_power_off maybe overwrote by this driver.
Signed-off-by: Robin Gong <b38343@freescale.com>
Acked-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Pull power supply and reset updates from Sebastian Reichel:
- Initial support for the following chips
* max77836 (charger)
* max14577 (charger)
* bq27742 (battery gauge)
* ltc2952 (poweroff)
* stih416 (restart)
* syscon-reboot (restart)
* gpio-restart (restart)
- cleanup of power supply core
- misc fixes in power supply and reset drivers
* tag 'for-v3.18' of git://git.infradead.org/battery-2.6: (48 commits)
power: ab8500_fg: Fix build warning
Documentation: charger: max14577: Update the date of introducing ABI
power: reset: corrections for simple syscon reboot driver
Documentation: power: reset: Add documentation for generic SYSCON reboot driver
power: reset: Add generic SYSCON register mapped reset
bq27x00_battery: Fix flag reading for bq27742
power: reset: use restart_notifier mechanism for msm-poweroff
power: Add simple gpio-restart driver
power: reset: st: Provide DT bindings for ST's Power Reset driver
power: reset: Add restart functionality for STiH41x platforms
power: charger-manager: Fix NULL pointer exception with missing cm-fuel-gauge
power: max14577: Fix circular config SYSFS dependency
power: gpio-charger: do not use gpio value directly
power: max8925: Use of_get_child_by_name
power: max8925: Fix NULL ptr dereference on memory allocation failure
bq27x00_battery: Add support to bq27742
Documentation: charger: max14577: Document exported sysfs entry
devicetree: mfd: max14577: Add device tree bindings document
power: max17040: Add ID for MAX77836 Fuel Gauge block
charger: max14577: Configure battery-dependent settings from DTS and sysfs
...
Conflicts:
drivers/power/reset/Kconfig
drivers/power/reset/Makefile
|
Asmaa Mnebhi
Emil Renner Berthing
Arnd Bergmann
Cristian Ciocaltea
Michael Klein
Geert Uytterhoeven
Lars Povlsen
Daniel González Cabanelas
Linus Torvalds
Anders Roxell
Daniel Golle
Baolin Wang
Krzysztof Kozlowski
Claudiu Beznea
Josef Friedl
Han Nandor
Thomas Gleixner
Vinod Koul
Baolin Wang
Alexandre Belloni
Dong Aisheng
Florian Fainelli
Linus Walleij
Paul Burton
Andy Yan
Chris Brand
Krzysztof Kozlowski
Nicolas Ferre
Richard Weinberger
Jun Nie
Moritz Fischer
Guenter Roeck
Kevin Cernekee
Robin Gong