| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
read ROHM BD71837 / BD71847 specific device tree bindings for
controlling the PMIC shutdown/reset states and voltages for
different HW states. The PMIC was designed to be used with NXP
i.MX8 SoC and it supports SNVS low power state which seems to
be typical for NXP i.MX SoCs. However, when SNVS is used we must
not allow SW to control enabling/disabling those regulators which
are crucial for system to boot as there is a HW limitation which
causes SW controlled regulators to be kept shut down after SNVS
reset.
Allow setting the SNVS to be used as reset target state and allow
marking those regulators which are critical for boot.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Tested-by: Angus Ainslie <angus@akkea.ca>
Reviewed-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
BD71837 and BD71847 have a HW functionality which leave power
rails OFF after powerof state:
- if they have been controlled by SW.
- if state transition from poweroff is done to SNVS
BD71837 can after reset transition from power-off to SNVS or
READY state depending on reset reason. By default only wathcdog
reset changes state from poweroff to ready. Change PMIC
configuration to always transition to READY in order to avoid
crucial power rails being OFF after reset.
If SNVS is required the crucial power rails should not be
controlled by SW - eg corresponding regulator control register
should have SEL bit kept zero. Currently the driver assumes all
regulators to be controlled by SW so it sets all SEL bits to 1.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The voltages in bd718xx_3rd_nodvs_buck_volts are in ascendant order, so use
regulator_map_voltage_ascend.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
0-Day tests found compilation error on x86.
Driver won't compile on x86_64 as "of_match_ptr" is
not found. Add missing include <linux/of.h>
At some point this fix was lost. So re-apply it.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
With gcc 4.1:
drivers/regulator/bd718x7-regulator.c: In function ‘bd718xx_probe’:
drivers/regulator/bd718x7-regulator.c:1020: warning: initialization from incompatible pointer type
drivers/regulator/bd718x7-regulator.c:1024: warning: initialization from incompatible pointer type
Apparently this old compiler can't handle the obscure double
indirection.
However, there is no need for a double indirection. Just store a
pointer to the array instead, like other drivers tend to do.
Fixes: 494edd266b945f36 ("regulator/mfd: Support ROHM BD71847 power management IC")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
All the fields in struct bd718xx_pmic are not really necessary.
Remove struct bd718xx_pmic to simplify the code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
rename bd71837-regulator.c to bd718x7-regulator.c to reflect the
fact that also BD71847 is now supported by the driver.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
Matti Vaittinen
Axel Lin
Mark Brown
Geert Uytterhoeven