aboutsummaryrefslogtreecommitdiffstatshomepage
path: root/include/linux/spi/mcp23s08.h (follow)
AgeCommit message (Collapse)AuthorFilesLines
2017-05-23pinctrl: mcp23s08: fix comment for mcp23s08_platform_data.baseSebastian Reichel1-5/+5
The comment does not match the driver, which actually supports automatic assignment. Fix this by updating the comment. Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-05-23pinctrl: mcp23s08: drop comment about missing irq supportSebastian Reichel1-3/+0
The driver supports using mcp23xxx as interrupt controller, so let's drop all comments stating otherwise. Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-05-23pinctrl: mcp23s08: simplify spi_present_mask handlingSebastian Reichel1-5/+1
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-05-23pinctrl: mcp23s08: generalize irq property handlingSebastian Reichel1-18/+0
This moves irq property handling from spi/i2c specific code into the generic mcp23s08_probe_one. This is possible because the device properties are named equally. As a side-effect this drops support for setting the properties via pdata, which has no mainline users. If boardcode wants to enable the chip as interrupt controller it can attach the device properties instead. Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-05-23pinctrl: mcp23s08: drop pullup config from pdataSebastian Reichel1-1/+0
mcp23s08 support configuration of the pullups using the pinconf framework. This removes the custom pullup configuration from platform data, which has no upstream users. Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-09-04gpio: mcp23s08 to support both device tree and platform dataSonic Zhang1-0/+18
Device tree is not enabled in some architecture where gpio driver mcp23s08 is still required. v2-changes: - Parse device tree properties into platform data other than individual variables. v3-changes: - Use of_node in gpio_chip device structure, because the struct device * always has an of_node which is NULL when OF is not used. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-07-15mcp23s08: get rid of setup/teardown callbacksPeter Korsgaard1-9/+0
There's no in-tree users, and bus notifiers are more generic anyway. Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-03-12gpio/mcp23s08: support mcp23s17 variantPeter Korsgaard1-6/+9
mpc23s17 is very similar to the mcp23s08, except that registers are 16bit wide, so extend the interface to work with both variants. The s17 variant also has an additional address pin, so adjust platform data structure to support up to 8 devices per SPI chipselect. Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-07-25gpio: mcp23s08 handles multiple chips per chipselectDavid Brownell1-9/+16
Teach the mcp23s08 driver about a curious feature of these chips: up to four of them can share the same chipselect, with the SPI signals wired in parallel, by matching two bits in the first protocol byte against two address lines on the chip. This is handled by three software changes: * Platform data now holds an array of per-chip structs, not just one chip's address and pullup configuration. * Probe() and remove() now use another level of structure, wrapping an instance of the original structure for each mcp23s08 chip sharing that chipselect. * The HAEN bit is set, so that the hardware address bits can no longer be ignored (boot firmware may not have enabled them). The "one struct per chip" preserves the guts of the current code, but platform_data will need minor changes. OLD: /* incorrect "slave" ID may not have mattered */ .slave = 3, .pullups = BIT(3) | BIT(1) | BIT(0), NEW: /* slave address _must_ match chip's wiring */ .chip[3] = { .is_present = true, .pullups = BIT(3) | BIT(1) | BIT(0), }, There's no change in how things _behave_ for spi_device nodes with a single mcp23s08 chip. New multi-chip configurations assign GPIOs in sequence, without holes. The spi_device just resembles a bigger controller, but internally it has multiple gpio_chip instances. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05mcp23s08 spi gpio expander supportDavid Brownell1-0/+24
Basic driver for 8-bit SPI based MCP23S08 GPIO expander, without support for IRQs or the shared chipselect mechanism. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>