| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Before sending Enter Mode for an Alt Mode, there is a gap between Discover
Modes and the Alt Mode driver queueing the Enter Mode VDM for the port
partner to send a message to the port.
If this message results in unregistering Alt Modes such as in a DR_SWAP,
then the following deadlock can occur with respect to the DisplayPort Alt
Mode driver:
1. The DR_SWAP state holds port->lock. Unregistering the Alt Mode driver
results in a cancel_work_sync() that waits for the current dp_altmode_work
to finish.
2. dp_altmode_work makes a call to tcpm_altmode_enter. The deadlock occurs
because tcpm_queue_vdm_unlock attempts to hold port->lock.
Before attempting to grab the lock, ensure that the port is in a state
vdm_run_state_machine can run in. Alt Mode unregistration will not occur
in these states.
Fixes: 03eafcfb60c0 ("usb: typec: tcpm: Add tcpm_queue_vdm_unlocked() helper")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240423202356.3372314-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Check and unregister existing source caps in tcpm_register_source_caps
function before registering new ones. This change fixes following
warning when port partner resends source caps after negotiating PD contract
for the purpose of re-negotiation.
[ 343.135030][ T151] sysfs: cannot create duplicate filename '/devices/virtual/usb_power_delivery/pd1/source-capabilities'
[ 343.135071][ T151] Call trace:
[ 343.135076][ T151] dump_backtrace+0xe8/0x108
[ 343.135099][ T151] show_stack+0x18/0x24
[ 343.135106][ T151] dump_stack_lvl+0x50/0x6c
[ 343.135119][ T151] dump_stack+0x18/0x24
[ 343.135126][ T151] sysfs_create_dir_ns+0xe0/0x140
[ 343.135137][ T151] kobject_add_internal+0x228/0x424
[ 343.135146][ T151] kobject_add+0x94/0x10c
[ 343.135152][ T151] device_add+0x1b0/0x4c0
[ 343.135187][ T151] device_register+0x20/0x34
[ 343.135195][ T151] usb_power_delivery_register_capabilities+0x90/0x20c
[ 343.135209][ T151] tcpm_pd_rx_handler+0x9f0/0x15b8
[ 343.135216][ T151] kthread_worker_fn+0x11c/0x260
[ 343.135227][ T151] kthread+0x114/0x1bc
[ 343.135235][ T151] ret_from_fork+0x10/0x20
[ 343.135265][ T151] kobject: kobject_add_internal failed for source-capabilities with -EEXIST, don't try to register things with the same name in the same directory.
Fixes: 8203d26905ee ("usb: typec: tcpm: Register USB Power Delivery Capabilities")
Cc: linux-usb@vger.kernel.org
Cc: stable@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240424223227.1807844-1-amitsd@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When a Fast Role Swap control message attempt results in a transition
to ERROR_RECOVERY, the TCPC can still queue a TCPM_SOURCING_VBUS event.
If the event is queued but processed after the tcpm_reset_port() call
in the PORT_RESET state, then the following occurs:
1. tcpm_reset_port() calls tcpm_init_vbus() to reset the vbus sourcing and
sinking state
2. tcpm_pd_event_handler() turns VBUS on before the port is in the default
state.
3. The port resolves as a sink. In the SNK_DISCOVERY state,
tcpm_set_charge() cannot set vbus to charge.
Clear pd events within PORT_RESET to get rid of non-applicable events.
Fixes: b17dd57118fe ("staging: typec: tcpm: Improve role swap with non PD capable partners")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240423202715.3375827-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tcpm_queue_vdm_unlocked queues VDMs over SOP regardless of input
parameter tx_sop_type. Fix tcpm_queue_vdm() call.
Fixes: 7e7877c55eb1 ("usb: typec: tcpm: add alt mode enter/exit/vdm support for sop'")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240423202546.3374218-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A virtual SuperSpeed device in the FreeBSD BVCP package
(https://bhyve.npulse.net/) presents an invalid ep0 maxpacket size of 256.
It stopped working with Linux following a recent commit because now we
check these sizes more carefully than before.
Fix this regression by using the bMaxpacketSize0 value in the device
descriptor for SuperSpeed or faster devices, even if it is invalid. This
is a very simple-minded change; we might want to check more carefully for
values that actually make some sense (for instance, no smaller than 64).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Roger Whittaker <roger.whittaker@suse.com>
Closes: https://bugzilla.suse.com/show_bug.cgi?id=1220569
Link: https://lore.kernel.org/linux-usb/9efbd569-7059-4575-983f-0ea30df41871@suse.com/
Fixes: 59cf44575456 ("USB: core: Fix oversight in SuperSpeed initialization")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/4058ac05-237c-4db4-9ecc-5af42bdb4501@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Testing ohci functionality with qemu's pci-ohci emulation often results
in ohci interface stalls, resulting in hung task timeouts.
The problem is caused by lost interrupts between the emulation and the
Linux kernel code. Additional interrupts raised while the ohci interrupt
handler in Linux is running and before the handler clears the interrupt
status are not handled. The fix for a similar problem in ehci suggests
that the problem is likely caused by edge-triggered MSI interrupts. See
commit 0b60557230ad ("usb: ehci: Prevent missed ehci interrupts with
edge-triggered MSI") for details.
Ensure that the ohci interrupt code handles all pending interrupts before
returning to solve the problem.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: David Laight <David.Laight@aculab.com>
Cc: stable@vger.kernel.org
Fixes: 306c54d0edb6 ("usb: hcd: Try MSI interrupts on PCI devices")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Link: https://lore.kernel.org/r/20240429154010.1507366-1-linux@roeck-us.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move disabling of the vdd-pdphy supply to the start() function which
enabled it for symmetry and to make sure that it is disabled as intended
in all error paths of pmic_typec_pdphy_reset() (i.e. not just when
qcom_pmic_typec_pdphy_enable() fails).
Cc: stable+noautosel@kernel.org # Not needed in any stable release, just a minor bugfix
Fixes: a4422ff22142 ("usb: typec: qcom: Add Qualcomm PMIC Type-C driver")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240418145730.4605-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure to stop and deregister the port in case of late probe errors
to avoid use-after-free issues when the underlying memory is released by
devres.
Fixes: a4422ff22142 ("usb: typec: qcom: Add Qualcomm PMIC Type-C driver")
Cc: stable@vger.kernel.org # 6.5
Cc: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240418145730.4605-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the USB driver passes a pointer into the TRB buffer for creq, this
buffer can be overwritten with the status response as soon as the event
is queued. This can make the final check return USB_GADGET_DELAYED_STATUS
when it shouldn't. Instead use the stored wLength.
Fixes: 4d644abf2569 ("usb: gadget: f_fs: Only return delayed status when len is 0")
Cc: stable <stable@kernel.org>
Signed-off-by: Chris Wulff <chris.wulff@biamp.com>
Link: https://lore.kernel.org/r/CO1PR17MB5419BD664264A558B2395E28E1112@CO1PR17MB5419.namprd17.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Testing with KASAN and syzkaller revealed a bug in port.c:disable_store():
usb_hub_to_struct_hub() can return NULL if the hub that the port belongs to
is concurrently removed, but the function does not check for this
possibility before dereferencing the returned value.
It turns out that the first dereference is unnecessary, since hub->intfdev
is the parent of the port device, so it can be changed easily. Adding a
check for hub == NULL prevents further problems.
The same bug exists in the disable_show() routine, and it can be fixed the
same way.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Yue Sun <samsun1006219@gmail.com>
Reported-by: xingwei lee <xrivendell7@gmail.com>
Link: https://lore.kernel.org/linux-usb/CAEkJfYON+ry7xPx=AiLR9jzUNT+i_Va68ACajOC3HoacOfL1ig@mail.gmail.com/
Fixes: f061f43d7418 ("usb: hub: port: add sysfs entry to switch port power")
CC: Michael Grzeschik <m.grzeschik@pengutronix.de>
CC: stable@vger.kernel.org
Link: https://lore.kernel.org/r/393aa580-15a5-44ca-ad3b-6462461cd313@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
GUSB3PIPECTL.SUSPENDENABLE and GUSB2PHYCFG.SUSPHY should be cleared
during initialization. Suspend during initialization can result in
undefined behavior due to clock synchronization failure, which often
seen as core soft reset timeout.
The programming guide recommended these bits to be cleared during
initialization for DWC_usb3.0 version 1.94 and above (along with
DWC_usb31 and DWC_usb32). The current check in the driver does not
account if it's set by default setting from coreConsultant.
This is especially the case for DRD when switching mode to ensure the
phy clocks are available to change mode. Depending on the
platforms/design, some may be affected more than others. This is noted
in the DWC_usb3x programming guide under the above registers.
Let's just disable them during driver load and mode switching. Restore
them when the controller initialization completes.
Note that some platforms workaround this issue by disabling phy suspend
through "snps,dis_u3_susphy_quirk" and "snps,dis_u2_susphy_quirk" when
they should not need to.
Cc: stable@vger.kernel.org
Fixes: 9ba3aca8fe82 ("usb: dwc3: Disable phy suspend after power-on reset")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20da4e5a0c4678c9587d3da23f83bdd6d77353e9.1713394973.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The xhci_plat.h should not need to include the entire xhci.h header.
This can cause redefinition in dwc3 if it selectively includes some xHCI
definitions. This is a prerequisite change for a fix to disable suspend
during initialization for dwc3.
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/310acfa01c957a10d9feaca3f7206269866ba2eb.1713394973.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This commit fixes uvc gadget support on 32-bit platforms.
Commit 0df28607c5cb ("usb: gadget: uvc: Generalise helper functions for
reuse") introduced a helper function __uvcg_iter_item_entries() to aid
with parsing lists of items on configfs attributes stores. This function
is a generalization of another very similar function, which used a
stack-allocated temporary buffer of fixed size for each item in the list
and used the sizeof() operator to check for potential buffer overruns.
The new function was changed to allocate the now variably sized temp
buffer on heap, but wasn't properly updated to also check for max buffer
size using the computed size instead of sizeof() operator.
As a result, the maximum item size was 7 (plus null terminator) on
64-bit platforms, and 3 on 32-bit ones. While 7 is accidentally just
barely enough, 3 is definitely too small for some of UVC configfs
attributes. For example, dwFrameInteval, specified in 100ns units,
usually has 6-digit item values, e.g. 166666 for 60fps.
Cc: stable@vger.kernel.org
Fixes: 0df28607c5cb ("usb: gadget: uvc: Generalise helper functions for reuse")
Signed-off-by: Ivan Avdeev <me@provod.works>
Link: https://lore.kernel.org/r/20240413150124.1062026-1-me@provod.works
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The OS descriptors logic had the high/low byte of w_value inverted, causing
the extended properties to not be accessible for interface != 0.
>From the Microsoft documentation:
https://learn.microsoft.com/en-us/windows-hardware/drivers/usbcon/microsoft-os-1-0-descriptors-specification
OS_Desc_CompatID.doc (w_index = 0x4):
- wValue:
High Byte = InterfaceNumber. InterfaceNumber is set to the number of the
interface or function that is associated with the descriptor, typically
0x00. Because a device can have only one extended compat ID descriptor,
it should ignore InterfaceNumber, regardless of the value, and simply
return the descriptor.
Low Byte = 0. PageNumber is used to retrieve descriptors that are larger
than 64 KB. The header section is 16 bytes, so PageNumber is set to 0 for
this request.
We currently do not support >64KB compat ID descriptors, so verify that the
low byte is 0.
OS_Desc_Ext_Prop.doc (w_index = 0x5):
- wValue:
High byte = InterfaceNumber. The high byte of wValue is set to the number
of the interface or function that is associated with the descriptor.
Low byte = PageNumber. The low byte of wValue is used to retrieve
descriptors that are larger than 64 KB. The header section is 10 bytes, so
PageNumber is set to 0 for this request.
We also don't support >64KB extended properties, so verify that the low byte
is 0 and use the high byte for the interface number.
Fixes: 37a3a533429e ("usb: gadget: OS Feature Descriptors support")
Cc: stable <stable@kernel.org>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Link: https://lore.kernel.org/r/20240404100635.3215340-1-peter@korsgaard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
FFS based applications can utilize the aio_cancel() callback to dequeue
pending USB requests submitted to the UDC. There is a scenario where the
FFS application issues an AIO cancel call, while the UDC is handling a
soft disconnect. For a DWC3 based implementation, the callstack looks
like the following:
DWC3 Gadget FFS Application
dwc3_gadget_soft_disconnect() ...
--> dwc3_stop_active_transfers()
--> dwc3_gadget_giveback(-ESHUTDOWN)
--> ffs_epfile_async_io_complete() ffs_aio_cancel()
--> usb_ep_free_request() --> usb_ep_dequeue()
There is currently no locking implemented between the AIO completion
handler and AIO cancel, so the issue occurs if the completion routine is
running in parallel to an AIO cancel call coming from the FFS application.
As the completion call frees the USB request (io_data->req) the FFS
application is also referencing it for the usb_ep_dequeue() call. This can
lead to accessing a stale/hanging pointer.
commit b566d38857fc ("usb: gadget: f_fs: use io_data->status consistently")
relocated the usb_ep_free_request() into ffs_epfile_async_io_complete().
However, in order to properly implement locking to mitigate this issue, the
spinlock can't be added to ffs_epfile_async_io_complete(), as
usb_ep_dequeue() (if successfully dequeuing a USB request) will call the
function driver's completion handler in the same context. Hence, leading
into a deadlock.
Fix this issue by moving the usb_ep_free_request() back to
ffs_user_copy_worker(), and ensuring that it explicitly sets io_data->req
to NULL after freeing it within the ffs->eps_lock. This resolves the race
condition above, as the ffs_aio_cancel() routine will not continue
attempting to dequeue a request that has already been freed, or the
ffs_user_copy_work() not freeing the USB request until the AIO cancel is
done referencing it.
This fix depends on
commit b566d38857fc ("usb: gadget: f_fs: use io_data->status
consistently")
Fixes: 2e4c7553cd6f ("usb: gadget: f_fs: add aio support")
Cc: stable <stable@kernel.org> # b566d38857fc ("usb: gadget: f_fs: use io_data->status consistently")
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240409014059.6740-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
jejb@linux.ibm.com no longer works.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
On arm64 machines, swsusp_save() faults if it attempts to access
MEMBLOCK_NOMAP memory ranges. This can be reproduced in QEMU using UEFI
when booting with rodata=off debug_pagealloc=off and CONFIG_KFENCE=n:
Unable to handle kernel paging request at virtual address ffffff8000000000
Mem abort info:
ESR = 0x0000000096000007
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x07: level 3 translation fault
Data abort info:
ISV = 0, ISS = 0x00000007, ISS2 = 0x00000000
CM = 0, WnR = 0, TnD = 0, TagAccess = 0
GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
swapper pgtable: 4k pages, 39-bit VAs, pgdp=00000000eeb0b000
[ffffff8000000000] pgd=180000217fff9803, p4d=180000217fff9803, pud=180000217fff9803, pmd=180000217fff8803, pte=0000000000000000
Internal error: Oops: 0000000096000007 [#1] SMP
Internal error: Oops: 0000000096000007 [#1] SMP
Modules linked in: xt_multiport ipt_REJECT nf_reject_ipv4 xt_conntrack nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 libcrc32c iptable_filter bpfilter rfkill at803x snd_hda_codec_hdmi snd_hda_intel snd_intel_dspcfg dwmac_generic stmmac_platform snd_hda_codec stmmac joydev pcs_xpcs snd_hda_core phylink ppdev lp parport ramoops reed_solomon ip_tables x_tables nls_iso8859_1 vfat multipath linear amdgpu amdxcp drm_exec gpu_sched drm_buddy hid_generic usbhid hid radeon video drm_suballoc_helper drm_ttm_helper ttm i2c_algo_bit drm_display_helper cec drm_kms_helper drm
CPU: 0 PID: 3663 Comm: systemd-sleep Not tainted 6.6.2+ #76
Source Version: 4e22ed63a0a48e7a7cff9b98b7806d8d4add7dc0
Hardware name: Greatwall GW-XXXXXX-XXX/GW-XXXXXX-XXX, BIOS KunLun BIOS V4.0 01/19/2021
pstate: 600003c5 (nZCv DAIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : swsusp_save+0x280/0x538
lr : swsusp_save+0x280/0x538
sp : ffffffa034a3fa40
x29: ffffffa034a3fa40 x28: ffffff8000001000 x27: 0000000000000000
x26: ffffff8001400000 x25: ffffffc08113e248 x24: 0000000000000000
x23: 0000000000080000 x22: ffffffc08113e280 x21: 00000000000c69f2
x20: ffffff8000000000 x19: ffffffc081ae2500 x18: 0000000000000000
x17: 6666662074736420 x16: 3030303030303030 x15: 3038666666666666
x14: 0000000000000b69 x13: ffffff9f89088530 x12: 00000000ffffffea
x11: 00000000ffff7fff x10: 00000000ffff7fff x9 : ffffffc08193f0d0
x8 : 00000000000bffe8 x7 : c0000000ffff7fff x6 : 0000000000000001
x5 : ffffffa0fff09dc8 x4 : 0000000000000000 x3 : 0000000000000027
x2 : 0000000000000000 x1 : 0000000000000000 x0 : 000000000000004e
Call trace:
swsusp_save+0x280/0x538
swsusp_arch_suspend+0x148/0x190
hibernation_snapshot+0x240/0x39c
hibernate+0xc4/0x378
state_store+0xf0/0x10c
kobj_attr_store+0x14/0x24
The reason is swsusp_save() -> copy_data_pages() -> page_is_saveable()
-> kernel_page_present() assuming that a page is always present when
can_set_direct_map() is false (all of rodata_full,
debug_pagealloc_enabled() and arm64_kfence_can_set_direct_map() false),
irrespective of the MEMBLOCK_NOMAP ranges. Such MEMBLOCK_NOMAP regions
should not be saved during hibernation.
This problem was introduced by changes to the pfn_valid() logic in
commit a7d9f306ba70 ("arm64: drop pfn_valid_within() and simplify
pfn_valid()").
Similar to other architectures, drop the !can_set_direct_map() check in
kernel_page_present() so that page_is_savable() skips such pages.
Fixes: a7d9f306ba70 ("arm64: drop pfn_valid_within() and simplify pfn_valid()")
Cc: <stable@vger.kernel.org> # 5.14.x
Suggested-by: Mike Rapoport <rppt@kernel.org>
Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Co-developed-by: xiongxin <xiongxin@kylinos.cn>
Signed-off-by: xiongxin <xiongxin@kylinos.cn>
Signed-off-by: Yaxiong Tian <tianyaxiong@kylinos.cn>
Acked-by: Mike Rapoport (IBM) <rppt@kernel.org>
Link: https://lore.kernel.org/r/20240417025248.386622-1-tianyaxiong@kylinos.cn
[catalin.marinas@arm.com: rework commit message]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
In iocg_pay_debt(), warn is triggered if 'active_list' is empty, which
is intended to confirm iocg is active when it has debt. However, warn
can be triggered during a blkcg or disk removal, if iocg_waitq_timer_fn()
is run at that time:
WARNING: CPU: 0 PID: 2344971 at block/blk-iocost.c:1402 iocg_pay_debt+0x14c/0x190
Call trace:
iocg_pay_debt+0x14c/0x190
iocg_kick_waitq+0x438/0x4c0
iocg_waitq_timer_fn+0xd8/0x130
__run_hrtimer+0x144/0x45c
__hrtimer_run_queues+0x16c/0x244
hrtimer_interrupt+0x2cc/0x7b0
The warn in this situation is meaningless. Since this iocg is being
removed, the state of the 'active_list' is irrelevant, and 'waitq_timer'
is canceled after removing 'active_list' in ioc_pd_free(), which ensures
iocg is freed after iocg_waitq_timer_fn() returns.
Therefore, add the check if iocg was already offlined to avoid warn
when removing a blkcg or disk.
Signed-off-by: Li Nan <linan122@huawei.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20240419093257.3004211-1-linan666@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The count field in struct trip_stats, representing the number of times
the zone temperature was above the trip point, needs to be incremented
in thermal_debug_tz_trip_up(), for two reasons.
First, if a trip point is crossed on the way up for the first time,
thermal_debug_update_temp() called from update_temperature() does
not see it because it has not been added to trips_crossed[] array
in the thermal zone's struct tz_debugfs object yet. Therefore, when
thermal_debug_tz_trip_up() is called after that, the trip point's
count value is 0, and the attempt to divide by it during the average
temperature computation leads to a divide error which causes the kernel
to crash. Setting the count to 1 before the division by incrementing it
fixes this problem.
Second, if a trip point is crossed on the way up, but it has been
crossed on the way up already before, its count value needs to be
incremented to make a record of the fact that the zone temperature is
above the trip now. Without doing that, if the mitigations applied
after crossing the trip cause the zone temperature to drop below its
threshold, the count will not be updated for this episode at all and
the average temperature in the trip statistics record will be somewhat
higher than it should be.
Fixes: 7ef01f228c9f ("thermal/debugfs: Add thermal debugfs information for mitigation episodes")
Cc :6.8+ <stable@vger.kernel.org> # 6.8+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The conversion from MIDI2 to MIDI1 UMP messages had a leftover
artifact (superfluous bit shift), and this resulted in the bogus type
check, leading to empty outputs. Let's fix it.
Fixes: e9e02819a98a ("ALSA: seq: Automatic conversion of UMP events")
Cc: <stable@vger.kernel.org>
Link: https://github.com/alsa-project/alsa-utils/issues/262
Message-ID: <20240419100442.14806-1-tiwai@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The Haier Boyue G42 with ALC269VC cannot detect the MIC of headset,
the line out and internal speaker until
ALC269VC_FIXUP_ACER_VCOPPERBOX_PINS quirk applied.
Signed-off-by: Ai Chao <aichao@kylinos.cn>
Cc: <stable@vger.kernel.org>
Message-ID: <20240419082159.476879-1-aichao@kylinos.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Even though the boot protocol stipulates otherwise, an exception has
been made for the EFI stub, and entering the core kernel with the MMU
enabled is permitted. This allows a substantial amount of cache
maintenance to be elided, wich is significant when fast boot times are
critical (e.g., for booting micro-VMs)
Once the initial ID map has been populated, the MMU is disabled as part
of the logic sequence that puts all system registers into a known state.
Any code that needs to execute within the window where the MMU is off is
cleaned to the PoC explicitly, which includes all of HYP text when
entering at EL2.
However, the current sequence of initializing the EL2 system registers
is not safe: HCR_EL2 is set to its nVHE initial state before SCTLR_EL2
is reprogrammed, and this means that a VHE-to-nVHE switch may occur
while the MMU is enabled. This switch causes some system registers as
well as page table descriptors to be interpreted in a different way,
potentially resulting in spurious exceptions relating to MMU
translation.
So disable the MMU explicitly first when entering in EL2 with the MMU
and caches enabled.
Fixes: 617861703830 ("efi: arm64: enter with MMU and caches enabled")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: <stable@vger.kernel.org> # 6.3.x
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240415075412.2347624-6-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
The Falkor erratum that results in the need for an ISB before clearing
the M bit in SCTLR_ELx only applies to execution at exception level x,
and so the workaround is not needed when disabling the EL1 MMU while
running at EL2.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20240415075412.2347624-5-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
The TX and RX DMA Channels used by the driver to exchange data with CPSW
are not guaranteed to be in a clean state during driver initialization.
The Bootloader could have used the same DMA Channels without cleaning them
up in the event of failure. Thus, reset and disable the DMA Channels to
ensure that they are in a clean state before using them.
Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Reported-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240417095425.2253876-1-s-vadapalli@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After the commit d2689b6a86b9 ("net: usb: ax88179_178a: avoid two
consecutive device resets"), reset operation, in which the default mac
address from the device is read, is not executed from bind operation and
the random address, that is pregenerated just in case, is direclty written
the first time in the device, so the default one from the device is not
even read. This writing is not dangerous because is volatile and the
default mac address is not missed.
In order to avoid this and keep the simplification to have only one
reset and reduce the delays, restore the reset from bind operation and
remove the reset that is commanded from open operation. The behavior is
the same but everything is ready for usbnet_probe.
Tested with ASIX AX88179 USB Gigabit Ethernet devices.
Restore the old behavior for the rest of possible devices because I don't
have the hardware to test.
cc: stable@vger.kernel.org # 6.6+
Fixes: d2689b6a86b9 ("net: usb: ax88179_178a: avoid two consecutive device resets")
Reported-by: Jarkko Palviainen <jarkko.palviainen@gmail.com>
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Link: https://lore.kernel.org/r/20240417085524.219532-1-jtornosm@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 4601b4b130de ("block: reopen the device in blkdev_reread_part")
lost the propagation of I/O errors from the low-level read of the
partition table to the user space caller of the BLKRRPART.
Apparently some user space relies on, so restore the propagation. This
isn't exactly pretty as other block device open calls explicitly do not
are about these errors, so add a new BLK_OPEN_STRICT_SCAN to opt into
the error propagation.
Fixes: 4601b4b130de ("block: reopen the device in blkdev_reread_part")
Reported-by: Saranya Muruganandam <saranyamohan@google.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Tested-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Link: https://lore.kernel.org/r/20240417144743.2277601-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Fix cpuid_deps[] to list the correct dependencies for GFNI, VAES, and
VPCLMULQDQ. These features don't depend on AVX512, and there exist CPUs
that support these features but not AVX512. GFNI actually doesn't even
depend on AVX.
This prevents GFNI from being unnecessarily disabled if AVX is disabled
to mitigate the GDS vulnerability.
This also prevents all three features from being unnecessarily disabled
if AVX512VL (or its dependency AVX512F) were to be disabled, but it
looks like there isn't any case where this happens anyway.
Fixes: c128dbfa0f87 ("x86/cpufeatures: Enable new SSE/AVX/AVX512 CPU features")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/r/20240417060434.47101-1-ebiggers@kernel.org
|
|
Add the following Telit FN920C04 compositions:
0x10a0: rmnet + tty (AT/NMEA) + tty (AT) + tty (diag)
T: Bus=03 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#= 5 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10a0 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FN920
S: SerialNumber=92c4c4d8
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x10a4: rmnet + tty (AT) + tty (AT) + tty (diag)
T: Bus=03 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#= 8 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10a4 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FN920
S: SerialNumber=92c4c4d8
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x10a9: rmnet + tty (AT) + tty (diag) + DPL (data packet logging) + adb
T: Bus=03 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#= 9 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10a9 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FN920
S: SerialNumber=92c4c4d8
C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none)
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The DWC3_EP_RESOURCE_ALLOCATED flag ensures that the resource of an
endpoint is only assigned once. Unless the endpoint is reset, don't
clear this flag. Otherwise we may set endpoint resource again, which
prevents the driver from initiate transfer after handling a STALL or
endpoint halt to the control endpoint.
Cc: stable@vger.kernel.org
Fixes: b311048c174d ("usb: dwc3: gadget: Rewrite endpoint allocation flow")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/00122b7cc5be06abef461776e7cc9f5ebc8bc1cb.1713229786.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 339f83612f3a569b194680768b22bf113c26a29d.
It has been found to cause problems in a number of Chromebook devices,
so revert the change until it can be brought back in a safe way.
Link: https://lore.kernel.org/r/385a3519-b45d-48c5-a6fd-a3fdb6bec92f@chromium.org
Reported-by:: Aleksander Morgado <aleksandermj@chromium.org>
Fixes: 339f83612f3a ("usb: cdc-wdm: close race between read and workqueue")
Cc: stable <stable@kernel.org>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit ad6bcdad2b6724e113f191a12f859a9e8456b26d. I had
nak'd it, and Greg said on the thread that it links that he wasn't going
to take it either, especially since it's not his code or his tree, but
then, seemingly accidentally, it got pushed up some months later, in
what looks like a mistake, with no further discussion in the linked
thread. So revert it, since it's clearly not intended.
Fixes: ad6bcdad2b67 ("vmgenid: emit uevent when VMGENID updates")
Cc: stable@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20230531095119.11202-2-bchalios@amazon.es
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
The RX byte accounting for jumbo packets was changed to fix a potential
use-after-free bug. However, that fix used the wrong variable and so
only accounted for the number of bytes in the final descriptor, not the
number of bytes in the whole packet.
To fix this, we can simply update our stats with the correct number of
bytes before calling napi_gro_receive().
Also rename pkt_len to desc_len in ravb_rx_gbeth() to avoid any future
confusion. The variable name pkt_len is correct in ravb_rx_rcar() as
that function does not handle packets spanning multiple descriptors.
Fixes: 5a5a3e564de6 ("ravb: Fix potential use-after-free in ravb_rx_gbeth()")
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Sending a 7kB ping packet to the RZ/G2L in v6.9-rc2 causes the following
backtrace:
WARNING: CPU: 0 PID: 0 at include/linux/skbuff.h:3127 skb_trim+0x30/0x38
Hardware name: Renesas SMARC EVK based on r9a07g044l2 (DT)
pc : skb_trim+0x30/0x38
lr : ravb_rx_csum_gbeth+0x40/0x90
Call trace:
skb_trim+0x30/0x38
ravb_rx_gbeth+0x56c/0x5cc
ravb_poll+0xa0/0x204
__napi_poll+0x38/0x17c
This is caused by ravb_rx_gbeth() calling ravb_rx_csum_gbeth() with the
wrong skb for a packet which spans multiple descriptors. To fix this,
use the correct skb.
Fixes: c2da9408579d ("ravb: Add Rx checksum offload support for GbEth")
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The RX loops in ravb_rx_gbeth() and ravb_rx_rcar() skip to the next loop
iteration if a zero-length descriptor is seen (indicating a DMA mapping
error). However, the current RX descriptor index `priv->cur_rx[q]` was
incremented at the end of the loop and so would not be incremented when
we skip to the next loop iteration. This would cause the loop to keep
seeing the same zero-length descriptor instead of moving on to the next
descriptor.
As the loop counter `i` still increments, the loop would eventually
terminate so there is no risk of being stuck here forever - but we
should still fix this to avoid wasting cycles.
To fix this, the RX descriptor index is incremented at the top of the
loop, in the for statement itself. The assignments of `entry` and `desc`
are brought into the loop to avoid the need for duplication.
Fixes: d8b48911fd24 ("ravb: fix ring memory allocation")
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The units of "work done" in the RX path should be packets instead of
descriptors.
Descriptors which are used by the hardware to record error conditions or
are empty in the case of a DMA mapping error should not count towards
our RX work budget.
Also make the limit variable unsigned as it can never be negative.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
regs->orig_ax has been set to -1 on entry so in the printout,
fred_bad_type() should use the passed parameter error_code.
Fixes: 14619d912b65 ("x86/fred: FRED entry/exit and dispatch code")
Signed-off-by: Hou Wenlong <houwenlong.hwl@antgroup.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: H. Peter Anvin (Intel) <hpa@zytor.com>
Link: https://lore.kernel.org/r/b2a8f0a41449d25240e314a2ddfbf6549511fb04.1713353612.git.houwenlong.hwl@antgroup.com
|
|
Add a FRED-specific INT80 handler and document why it differs from the
current one. Eventually, the common bits will be unified once FRED hw is
available and it turns out that no further changes are needed but for
now, keep the handlers separate for everyone's sanity's sake.
[ bp: Zap duplicated commit message, massage. ]
Fixes: 55617fb991df ("x86/entry: Do not allow external 0x80 interrupts")
Suggested-by: H. Peter Anvin (Intel) <hpa@zytor.com>
Signed-off-by: Xin Li (Intel) <xin@zytor.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20240417174731.4189592-1-xin@zytor.com
|
|
The headset mic requires a fixup to be properly detected/used.
As a reference, this specific model from 2021 reports
the following devices:
https://alsa-project.org/db/?f=1a5ddeb0b151db8fe051407f5bb1c075b7dd3e4a
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: <stable@vger.kernel.org>
Message-ID: <b92a9e49fb504eec8416bcc6882a52de89450102.1713370457.git.mchehab@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Update the USB serial option driver support for the Rolling
LTE modules.
- VID:PID 33f8:01a2, RW101-GL for laptop debug M.2 cards(with MBIM
interface for /Linux/Chrome OS)
0x01a2: mbim, diag, at, pipe
- VID:PID 33f8:01a3, RW101-GL for laptop debug M.2 cards(with MBIM
interface for /Linux/Chrome OS)
0x01a3: mbim, pipe
- VID:PID 33f8:01a4, RW101-GL for laptop debug M.2 cards(with MBIM
interface for /Linux/Chrome OS)
0x01a4: mbim, diag, at, pipe
- VID:PID 33f8:0104, RW101-GL for laptop debug M.2 cards(with RMNET
interface for /Linux/Chrome OS)
0x0104: RMNET, diag, at, pipe
- VID:PID 33f8:0115, RW135-GL for laptop debug M.2 cards(with MBIM
interface for /Linux/Chrome OS)
0x0115: MBIM, diag, at, pipe
Here are the outputs of usb-devices:
T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 5 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=33f8 ProdID=01a2 Rev=05.15
S: Manufacturer=Rolling Wireless S.a.r.l.
S: Product=Rolling Module
S: SerialNumber=12345678
C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 8 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=33f8 ProdID=01a3 Rev=05.15
S: Manufacturer=Rolling Wireless S.a.r.l.
S: Product=Rolling Module
S: SerialNumber=12345678
C: #Ifs= 3 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 17 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=33f8 ProdID=01a4 Rev=05.15
S: Manufacturer=Rolling Wireless S.a.r.l.
S: Product=Rolling Module
S: SerialNumber=12345678
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=33f8 ProdID=0104 Rev=05.04
S: Manufacturer=Rolling Wireless S.a.r.l.
S: Product=Rolling Module
S: SerialNumber=ba2eb033
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=896mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=40 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=88(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
E: Ad=05(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=89(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=33f8 ProdID=0115 Rev=05.15
S: Manufacturer=Rolling Wireless S.a.r.l.
S: Product=Rolling Module
S: SerialNumber=12345678
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Vanillan Wang <vanillanwang@163.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Update the USB serial option driver to support Longsung U8300/U9300.
For U8300
Interface 4 is used by for QMI interface in stock firmware of U8300, the
router which uses U8300 modem.
Interface 5 is used by for ADB interface in stock firmware of U8300, the
router which uses U8300 modem.
Interface mapping is:
0: unknown (Debug), 1: AT (Modem), 2: AT, 3: PPP (NDIS / Pipe), 4: QMI, 5: ADB
T: Bus=05 Lev=01 Prnt=03 Port=02 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1c9e ProdID=9b05 Rev=03.18
S: Manufacturer=Android
S: Product=Android
C: #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
For U9300
Interface 1 is used by for ADB interface in stock firmware of U9300, the
router which uses U9300 modem.
Interface 4 is used by for QMI interface in stock firmware of U9300, the
router which uses U9300 modem.
Interface mapping is:
0: ADB, 1: AT (Modem), 2: AT, 3: PPP (NDIS / Pipe), 4: QMI
Note: Interface 3 of some models of the U9300 series can send AT commands.
T: Bus=05 Lev=01 Prnt=05 Port=04 Cnt=01 Dev#= 6 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1c9e ProdID=9b3c Rev=03.18
S: Manufacturer=Android
S: Product=Android
C: #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
Tested successfully using Modem Manager on U9300.
Tested successfully AT commands using If=1, If=2 and If=3 on U9300.
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Reviewed-by: Lars Melin <larsm17@gmail.com>
[ johan: drop product defines, trim commit message ]
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
change HDA & AMP configuration from ALC287_FIXUP_CS35L41_I2C_2 to
ALC287_FIXUP_MG_RTKC_CSAMP_CS35L41_I2C_THINKPAD for ThinkBook 16P Gen4
models to fix volumn control issue (cannot fully mute).
Signed-off-by: Huayu Zhang <zhanghuayu1233@qq.com>
Fixes: 6214e24cae9b ("ALSA: hda/realtek: Add quirks for Lenovo Thinkbook 16P laptops")
Message-ID: <tencent_37EB880C5E5BD99D21C16B288115C4545F06@qq.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Added the correct pin table for Asus GU605M and GA403U, enabling all
speakers to be controlled with the master.
Updated quirks for GU605M and GA403U by including the pin table patch
in the chain.
Co-developed-by: Luke D. Jones <luke@ljones.dev>
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Signed-off-by: Vitalii Torshyn <vitaly.torshyn@gmail.com>
Message-ID: <20240411125803.18539-1-vitaly.torshyn@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add new vendor_id and subsystem_id to support new Lenovo laptop
ThinkPad ICE-1
Signed-off-by: Shenghao Ding <shenghao-ding@ti.com>
Cc: <stable@vger.kernel.org>
Message-ID: <20240411091823.1644-1-shenghao-ding@ti.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The WLAN + WED reset sequence relies on being able to receive interrupts from
the card, in order to synchronize individual steps with the firmware.
When WED is stopped, leave interrupts running and rely on the driver turning
off unwanted ones.
WED DMA also needs to be disabled before resetting.
Fixes: f78cd9c783e0 ("net: ethernet: mtk_wed: update mtk_wed_stop")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20240416082330.82564-1-nbd@nbd.name
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update the qmi_wwan driver support for the Rolling
LTE modules.
- VID:PID 33f8:0104, RW101-GL for laptop debug M.2 cards(with RMNET
interface for /Linux/Chrome OS)
0x0104: RMNET, diag, at, pipe
Here are the outputs of usb-devices:
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=33f8 ProdID=0104 Rev=05.04
S: Manufacturer=Rolling Wireless S.a.r.l.
S: Product=Rolling Module
S: SerialNumber=ba2eb033
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=896mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=40 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=88(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
E: Ad=05(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=89(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
Signed-off-by: Vanillan Wang <vanillanwang@163.com>
Link: https://lore.kernel.org/r/20240416120713.24777-1-vanillanwang@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Apparently it's more legal to pass the format as NULL, than
it is to use an empty string. Clang complains about empty
formats:
./../kselftest_harness.h:1207:30: warning: format string is empty
[-Wformat-zero-length]
1207 | diagnostic ? "%s" : "", diagnostic);
| ^~
1 warning generated.
Reported-by: Sean Christopherson <seanjc@google.com>
Link: https://lore.kernel.org/all/20240409224256.1581292-1-seanjc@google.com
Fixes: 378193eff339 ("selftests: kselftest_harness: let PASS / FAIL provide diagnostic")
Tested-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Link: https://lore.kernel.org/r/20240416151048.1682352-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the mirred action is used on a classful egress qdisc and a packet is
mirrored or redirected to self we hit a qdisc lock deadlock.
See trace below.
[..... other info removed for brevity....]
[ 82.890906]
[ 82.890906] ============================================
[ 82.890906] WARNING: possible recursive locking detected
[ 82.890906] 6.8.0-05205-g77fadd89fe2d-dirty #213 Tainted: G W
[ 82.890906] --------------------------------------------
[ 82.890906] ping/418 is trying to acquire lock:
[ 82.890906] ffff888006994110 (&sch->q.lock){+.-.}-{3:3}, at:
__dev_queue_xmit+0x1778/0x3550
[ 82.890906]
[ 82.890906] but task is already holding lock:
[ 82.890906] ffff888006994110 (&sch->q.lock){+.-.}-{3:3}, at:
__dev_queue_xmit+0x1778/0x3550
[ 82.890906]
[ 82.890906] other info that might help us debug this:
[ 82.890906] Possible unsafe locking scenario:
[ 82.890906]
[ 82.890906] CPU0
[ 82.890906] ----
[ 82.890906] lock(&sch->q.lock);
[ 82.890906] lock(&sch->q.lock);
[ 82.890906]
[ 82.890906] *** DEADLOCK ***
[ 82.890906]
[..... other info removed for brevity....]
Example setup (eth0->eth0) to recreate
tc qdisc add dev eth0 root handle 1: htb default 30
tc filter add dev eth0 handle 1: protocol ip prio 2 matchall \
action mirred egress redirect dev eth0
Another example(eth0->eth1->eth0) to recreate
tc qdisc add dev eth0 root handle 1: htb default 30
tc filter add dev eth0 handle 1: protocol ip prio 2 matchall \
action mirred egress redirect dev eth1
tc qdisc add dev eth1 root handle 1: htb default 30
tc filter add dev eth1 handle 1: protocol ip prio 2 matchall \
action mirred egress redirect dev eth0
We fix this by adding an owner field (CPU id) to struct Qdisc set after
root qdisc is entered. When the softirq enters it a second time, if the
qdisc owner is the same CPU, the packet is dropped to break the loop.
Reported-by: Mingshuai Ren <renmingshuai@huawei.com>
Closes: https://lore.kernel.org/netdev/20240314111713.5979-1-renmingshuai@huawei.com/
Fixes: 3bcb846ca4cf ("net: get rid of spin_trylock() in net_tx_action()")
Fixes: e578d9c02587 ("net: sched: use counter to break reclassify loops")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Victor Nogueira <victor@mojatatu.com>
Reviewed-by: Pedro Tammela <pctammela@mojatatu.com>
Tested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://lore.kernel.org/r/20240415210728.36949-1-victor@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The delete set command does not rely on the transaction object for
element removal, therefore, a combination of delete element + delete set
from the abort path could result in restoring twice the refcount of the
mapping.
Check for inactive element in the next generation for the delete element
command in the abort path, skip restoring state if next generation bit
has been already cleared. This is similar to the activate logic using
the set walk iterator.
[ 6170.286929] ------------[ cut here ]------------
[ 6170.286939] WARNING: CPU: 6 PID: 790302 at net/netfilter/nf_tables_api.c:2086 nf_tables_chain_destroy+0x1f7/0x220 [nf_tables]
[ 6170.287071] Modules linked in: [...]
[ 6170.287633] CPU: 6 PID: 790302 Comm: kworker/6:2 Not tainted 6.9.0-rc3+ #365
[ 6170.287768] RIP: 0010:nf_tables_chain_destroy+0x1f7/0x220 [nf_tables]
[ 6170.287886] Code: df 48 8d 7d 58 e8 69 2e 3b df 48 8b 7d 58 e8 80 1b 37 df 48 8d 7d 68 e8 57 2e 3b df 48 8b 7d 68 e8 6e 1b 37 df 48 89 ef eb c4 <0f> 0b 48 83 c4 08 5b 5d 41 5c 41 5d 41 5e 41 5f c3 cc cc cc cc 0f
[ 6170.287895] RSP: 0018:ffff888134b8fd08 EFLAGS: 00010202
[ 6170.287904] RAX: 0000000000000001 RBX: ffff888125bffb28 RCX: dffffc0000000000
[ 6170.287912] RDX: 0000000000000003 RSI: ffffffffa20298ab RDI: ffff88811ebe4750
[ 6170.287919] RBP: ffff88811ebe4700 R08: ffff88838e812650 R09: fffffbfff0623a55
[ 6170.287926] R10: ffffffff8311d2af R11: 0000000000000001 R12: ffff888125bffb10
[ 6170.287933] R13: ffff888125bffb10 R14: dead000000000122 R15: dead000000000100
[ 6170.287940] FS: 0000000000000000(0000) GS:ffff888390b00000(0000) knlGS:0000000000000000
[ 6170.287948] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 6170.287955] CR2: 00007fd31fc00710 CR3: 0000000133f60004 CR4: 00000000001706f0
[ 6170.287962] Call Trace:
[ 6170.287967] <TASK>
[ 6170.287973] ? __warn+0x9f/0x1a0
[ 6170.287986] ? nf_tables_chain_destroy+0x1f7/0x220 [nf_tables]
[ 6170.288092] ? report_bug+0x1b1/0x1e0
[ 6170.287986] ? nf_tables_chain_destroy+0x1f7/0x220 [nf_tables]
[ 6170.288092] ? report_bug+0x1b1/0x1e0
[ 6170.288104] ? handle_bug+0x3c/0x70
[ 6170.288112] ? exc_invalid_op+0x17/0x40
[ 6170.288120] ? asm_exc_invalid_op+0x1a/0x20
[ 6170.288132] ? nf_tables_chain_destroy+0x2b/0x220 [nf_tables]
[ 6170.288243] ? nf_tables_chain_destroy+0x1f7/0x220 [nf_tables]
[ 6170.288366] ? nf_tables_chain_destroy+0x2b/0x220 [nf_tables]
[ 6170.288483] nf_tables_trans_destroy_work+0x588/0x590 [nf_tables]
Fixes: 591054469b3e ("netfilter: nf_tables: revisit chain/object refcounting from elements")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The flags in the software node properties are supposed to be
the GPIO lookup flags, which are provided by gpio/machine.h,
as the software nodes are the kernel internal thing and doesn't
need to rely to any of ABIs.
Fixes: e7f9ff5dc90c ("gpiolib: add support for software nodes")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
RD Babiera
Amit Sunil Dhamne
Alan Stern
Guenter Roeck
Johan Hovold
Chris Wulff
Thinh Nguyen
Ivan Avdeev
Peter Korsgaard
Wesley Cheng
Linus Torvalds
James Bottomley
Yaxiong Tian
Li Nan
Rafael J. Wysocki
Takashi Iwai
Ai Chao
Ard Biesheuvel
Siddharth Vadapalli
Jose Ignacio Tornos Martinez
Christoph Hellwig
Eric Biggers
Daniele Palmas
Greg Kroah-Hartman
Jason A. Donenfeld
Paul Barker
Hou Wenlong
Xin Li (Intel)
Mauro Carvalho Chehab
Vanillan Wang
Coia Prant
Huayu Zhang
Vitalii Torshyn
Shenghao Ding
Felix Fietkau
Jakub Kicinski
Eric Dumazet
Pablo Neira Ayuso
Andy Shevchenko