| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
ib2 and airoha_foe_mac_info_common have not the same offsets in
airoha_foe_bridge and airoha_foe_ipv6 structures. Current codebase does
not accelerate IPv6 traffic in bridge mode since ib2 and l2 info are not
set properly copying airoha_foe_bridge struct into airoha_foe_ipv6 one
in airoha_ppe_foe_commit_subflow_entry routine.
Fix IPv6 hw acceleration in bridge mode resolving ib2 and
airoha_foe_mac_info_common overwrite in
airoha_ppe_foe_commit_subflow_entry() and configuring them with proper
values.
Fixes: cd53f622611f ("net: airoha: Add L2 hw acceleration support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250602-airoha-flowtable-ipv6-fix-v2-2-3287f8b55214@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
UPDMEM source-mac table is a key-value map used to store devices mac
addresses according to the port identifier. UPDMEM source mac table is
used during IPv6 traffic hw acceleration since PPE entries, for space
constraints, do not contain the full source mac address but just the
identifier in the UPDMEM source-mac table.
Configure UPDMEM source-mac table with device mac addresses and set
the source-mac ID field for PPE IPv6 entries in order to select the
proper device mac address as source mac for L3 IPv6 hw accelerated traffic.
Fixes: 00a7678310fe ("net: airoha: Introduce flowtable offload support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250602-airoha-flowtable-ipv6-fix-v2-1-3287f8b55214@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
We have the logic to include net/lib automatically for net related
selftests. However, currently, this logic is only in install target
which means only `make install` will have net/lib included. This commit
adds the logic to all target so that all `make`, `make run_tests` and
`make install` will have net/lib included in net related selftests.
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Link: https://patch.msgid.link/20250601142914.13379-1-minhquangbui99@gmail.com
Fixes: b86761ff6374 ("selftests: net: add scaffolding for Netlink tests in Python")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Commit 3d010c8031e3 ("udp: do not accept non-tunnel GSO skbs landing
in a tunnel") added checks in linux stack to not accept non-tunnel
GRO packets landing in a tunnel. This exposed an issue in vmxnet3
which was not correctly reporting GRO packets for tunnel packets.
This patch fixes this issue by setting correct GSO type for the
tunnel packets.
Currently, vmxnet3 does not support reporting inner fields for LRO
tunnel packets. The issue is not seen for egress drivers that do not
use skb inner fields. The workaround is to enable tnl-segmentation
offload on the egress interfaces if the driver supports it. This
problem pre-exists this patch fix and can be addressed as a separate
future patch.
Fixes: dacce2be3312 ("vmxnet3: add geneve and vxlan tunnel offload support")
Signed-off-by: Ronak Doshi <ronak.doshi@broadcom.com>
Acked-by: Guolin Yang <guolin.yang@broadcom.com>
Link: https://patch.msgid.link/20250530152701.70354-1-ronak.doshi@broadcom.com
[pabeni@redhat.com: dropped the changelog]
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This reverts commit a571a9a1b120264e24b41eddf1ac5140131bfa84.
The commit in question breaks kunit for older compilers:
$ gcc --version
gcc (GCC) 11.5.0 20240719 (Red Hat 11.5.0-5)
$ ./tools/testing/kunit/kunit.py run --alltests --json --arch=x86_64
Configuring KUnit Kernel ...
Regenerating .config ...
Populating config with:
$ make ARCH=x86_64 O=.kunit olddefconfig
ERROR:root:Not all Kconfig options selected in kunitconfig were in the generated .config.
This is probably due to unsatisfied dependencies.
Missing: CONFIG_INIT_STACK_ALL_PATTERN=y
Link: https://lore.kernel.org/20250529083811.778bc31b@kernel.org
Fixes: a571a9a1b120 ("kunit: configs: Enable CONFIG_INIT_STACK_ALL_PATTERN in all_tests")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://patch.msgid.link/20250530135800.13437-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When driver handles the napi rx polling requests, the netdev might
have been released by the dellink logic triggered by the disconnect
operation on user plane. However, in the logic of processing skb in
polling, an invalid netdev is still being used, which causes a panic.
BUG: kernel NULL pointer dereference, address: 00000000000000f1
Oops: 0000 [#1] PREEMPT SMP NOPTI
RIP: 0010:dev_gro_receive+0x3a/0x620
[...]
Call Trace:
<IRQ>
? __die_body+0x68/0xb0
? page_fault_oops+0x379/0x3e0
? exc_page_fault+0x4f/0xa0
? asm_exc_page_fault+0x22/0x30
? __pfx_t7xx_ccmni_recv_skb+0x10/0x10 [mtk_t7xx (HASH:1400 7)]
? dev_gro_receive+0x3a/0x620
napi_gro_receive+0xad/0x170
t7xx_ccmni_recv_skb+0x48/0x70 [mtk_t7xx (HASH:1400 7)]
t7xx_dpmaif_napi_rx_poll+0x590/0x800 [mtk_t7xx (HASH:1400 7)]
net_rx_action+0x103/0x470
irq_exit_rcu+0x13a/0x310
sysvec_apic_timer_interrupt+0x56/0x90
</IRQ>
Fixes: 5545b7b9f294 ("net: wwan: t7xx: Add NAPI support")
Signed-off-by: Jinjian Song <jinjian.song@fibocom.com>
Link: https://patch.msgid.link/20250530031648.5592-1-jinjian.song@fibocom.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Commit a1e40ac5b5e9 ("net: gso: fix udp gso fraglist segmentation after
pull from frag_list") detected invalid geometry in frag_list skbs and
redirects them from skb_segment_list to more robust skb_segment. But some
packets with modified geometry can also hit bugs in that code. We don't
know how many such cases exist. Addressing each one by one also requires
touching the complex skb_segment code, which risks introducing bugs for
other types of skbs. Instead, linearize all these packets that fail the
basic invariants on gso fraglist skbs. That is more robust.
If only part of the fraglist payload is pulled into head_skb, it will
always cause exception when splitting skbs by skb_segment. For detailed
call stack information, see below.
Valid SKB_GSO_FRAGLIST skbs
- consist of two or more segments
- the head_skb holds the protocol headers plus first gso_size
- one or more frag_list skbs hold exactly one segment
- all but the last must be gso_size
Optional datapath hooks such as NAT and BPF (bpf_skb_pull_data) can
modify fraglist skbs, breaking these invariants.
In extreme cases they pull one part of data into skb linear. For UDP,
this causes three payloads with lengths of (11,11,10) bytes were
pulled tail to become (12,10,10) bytes.
The skbs no longer meets the above SKB_GSO_FRAGLIST conditions because
payload was pulled into head_skb, it needs to be linearized before pass
to regular skb_segment.
skb_segment+0xcd0/0xd14
__udp_gso_segment+0x334/0x5f4
udp4_ufo_fragment+0x118/0x15c
inet_gso_segment+0x164/0x338
skb_mac_gso_segment+0xc4/0x13c
__skb_gso_segment+0xc4/0x124
validate_xmit_skb+0x9c/0x2c0
validate_xmit_skb_list+0x4c/0x80
sch_direct_xmit+0x70/0x404
__dev_queue_xmit+0x64c/0xe5c
neigh_resolve_output+0x178/0x1c4
ip_finish_output2+0x37c/0x47c
__ip_finish_output+0x194/0x240
ip_finish_output+0x20/0xf4
ip_output+0x100/0x1a0
NF_HOOK+0xc4/0x16c
ip_forward+0x314/0x32c
ip_rcv+0x90/0x118
__netif_receive_skb+0x74/0x124
process_backlog+0xe8/0x1a4
__napi_poll+0x5c/0x1f8
net_rx_action+0x154/0x314
handle_softirqs+0x154/0x4b8
[118.376811] [C201134] rxq0_pus: [name:bug&]kernel BUG at net/core/skbuff.c:4278!
[118.376829] [C201134] rxq0_pus: [name:traps&]Internal error: Oops - BUG: 00000000f2000800 [#1] PREEMPT SMP
[118.470774] [C201134] rxq0_pus: [name:mrdump&]Kernel Offset: 0x178cc00000 from 0xffffffc008000000
[118.470810] [C201134] rxq0_pus: [name:mrdump&]PHYS_OFFSET: 0x40000000
[118.470827] [C201134] rxq0_pus: [name:mrdump&]pstate: 60400005 (nZCv daif +PAN -UAO)
[118.470848] [C201134] rxq0_pus: [name:mrdump&]pc : [0xffffffd79598aefc] skb_segment+0xcd0/0xd14
[118.470900] [C201134] rxq0_pus: [name:mrdump&]lr : [0xffffffd79598a5e8] skb_segment+0x3bc/0xd14
[118.470928] [C201134] rxq0_pus: [name:mrdump&]sp : ffffffc008013770
Fixes: a1e40ac5b5e9 ("gso: fix udp gso fraglist segmentation after pull from frag_list")
Signed-off-by: Shiming Cheng <shiming.cheng@mediatek.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In Cilium, we use bpf_csum_diff + bpf_l4_csum_replace to, among other
things, update the L4 checksum after reverse SNATing IPv6 packets. That
use case is however not currently supported and leads to invalid
skb->csum values in some cases. This patch adds support for IPv6 address
changes in bpf_l4_csum_update via a new flag.
When calling bpf_l4_csum_replace in Cilium, it ends up calling
inet_proto_csum_replace_by_diff:
1: void inet_proto_csum_replace_by_diff(__sum16 *sum, struct sk_buff *skb,
2: __wsum diff, bool pseudohdr)
3: {
4: if (skb->ip_summed != CHECKSUM_PARTIAL) {
5: csum_replace_by_diff(sum, diff);
6: if (skb->ip_summed == CHECKSUM_COMPLETE && pseudohdr)
7: skb->csum = ~csum_sub(diff, skb->csum);
8: } else if (pseudohdr) {
9: *sum = ~csum_fold(csum_add(diff, csum_unfold(*sum)));
10: }
11: }
The bug happens when we're in the CHECKSUM_COMPLETE state. We've just
updated one of the IPv6 addresses. The helper now updates the L4 header
checksum on line 5. Next, it updates skb->csum on line 7. It shouldn't.
For an IPv6 packet, the updates of the IPv6 address and of the L4
checksum will cancel each other. The checksums are set such that
computing a checksum over the packet including its checksum will result
in a sum of 0. So the same is true here when we update the L4 checksum
on line 5. We'll update it as to cancel the previous IPv6 address
update. Hence skb->csum should remain untouched in this case.
The same bug doesn't affect IPv4 packets because, in that case, three
fields are updated: the IPv4 address, the IP checksum, and the L4
checksum. The change to the IPv4 address and one of the checksums still
cancel each other in skb->csum, but we're left with one checksum update
and should therefore update skb->csum accordingly. That's exactly what
inet_proto_csum_replace_by_diff does.
This special case for IPv6 L4 checksums is also described atop
inet_proto_csum_replace16, the function we should be using in this case.
This patch introduces a new bpf_l4_csum_replace flag, BPF_F_IPV6,
to indicate that we're updating the L4 checksum of an IPv6 packet. When
the flag is set, inet_proto_csum_replace_by_diff will skip the
skb->csum update.
Fixes: 7d672345ed295 ("bpf: add generic bpf_csum_diff helper")
Signed-off-by: Paul Chaignon <paul.chaignon@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://patch.msgid.link/96a6bc3a443e6f0b21ff7b7834000e17fb549e05.1748509484.git.paul.chaignon@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
During ILA address translations, the L4 checksums can be handled in
different ways. One of them, adj-transport, consist in parsing the
transport layer and updating any found checksum. This logic relies on
inet_proto_csum_replace_by_diff and produces an incorrect skb->csum when
in state CHECKSUM_COMPLETE.
This bug can be reproduced with a simple ILA to SIR mapping, assuming
packets are received with CHECKSUM_COMPLETE:
$ ip a show dev eth0
14: eth0@if15: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
link/ether 62:ae:35:9e:0f:8d brd ff:ff:ff:ff:ff:ff link-netnsid 0
inet6 3333:0:0:1::c078/64 scope global
valid_lft forever preferred_lft forever
inet6 fd00:10:244:1::c078/128 scope global nodad
valid_lft forever preferred_lft forever
inet6 fe80::60ae:35ff:fe9e:f8d/64 scope link proto kernel_ll
valid_lft forever preferred_lft forever
$ ip ila add loc_match fd00:10:244:1 loc 3333:0:0:1 \
csum-mode adj-transport ident-type luid dev eth0
Then I hit [fd00:10:244:1::c078]:8000 with a server listening only on
[3333:0:0:1::c078]:8000. With the bug, the SYN packet is dropped with
SKB_DROP_REASON_TCP_CSUM after inet_proto_csum_replace_by_diff changed
skb->csum. The translation and drop are visible on pwru [1] traces:
IFACE TUPLE FUNC
eth0:9 [fd00:10:244:3::3d8]:51420->[fd00:10:244:1::c078]:8000(tcp) ipv6_rcv
eth0:9 [fd00:10:244:3::3d8]:51420->[fd00:10:244:1::c078]:8000(tcp) ip6_rcv_core
eth0:9 [fd00:10:244:3::3d8]:51420->[fd00:10:244:1::c078]:8000(tcp) nf_hook_slow
eth0:9 [fd00:10:244:3::3d8]:51420->[fd00:10:244:1::c078]:8000(tcp) inet_proto_csum_replace_by_diff
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) tcp_v6_early_demux
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) ip6_route_input
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) ip6_input
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) ip6_input_finish
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) ip6_protocol_deliver_rcu
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) raw6_local_deliver
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) ipv6_raw_deliver
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) tcp_v6_rcv
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) __skb_checksum_complete
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) kfree_skb_reason(SKB_DROP_REASON_TCP_CSUM)
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) skb_release_head_state
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) skb_release_data
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) skb_free_head
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) kfree_skbmem
This is happening because inet_proto_csum_replace_by_diff is updating
skb->csum when it shouldn't. The L4 checksum is updated such that it
"cancels" the IPv6 address change in terms of checksum computation, so
the impact on skb->csum is null.
Note this would be different for an IPv4 packet since three fields
would be updated: the IPv4 address, the IP checksum, and the L4
checksum. Two would cancel each other and skb->csum would still need
to be updated to take the L4 checksum change into account.
This patch fixes it by passing an ipv6 flag to
inet_proto_csum_replace_by_diff, to skip the skb->csum update if we're
in the IPv6 case. Note the behavior of the only other user of
inet_proto_csum_replace_by_diff, the BPF subsystem, is left as is in
this patch and fixed in the subsequent patch.
With the fix, using the reproduction from above, I can confirm
skb->csum is not touched by inet_proto_csum_replace_by_diff and the TCP
SYN proceeds to the application after the ILA translation.
Link: https://github.com/cilium/pwru [1]
Fixes: 65d7ab8de582 ("net: Identifier Locator Addressing module")
Signed-off-by: Paul Chaignon <paul.chaignon@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://patch.msgid.link/b5539869e3550d46068504feb02d37653d939c0b.1748509484.git.paul.chaignon@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If the ptp_rate recorded earlier in the driver happens to be 0, this
bogus value will propagate up to EST configuration, where it will
trigger a division by 0.
Prevent this division by 0 by adding the corresponding check and error
code.
Suggested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Fixes: 8572aec3d0dc ("net: stmmac: Add basic EST support for XGMAC")
Link: https://patch.msgid.link/20250529-stmmac_tstamp_div-v4-2-d73340a794d5@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The stmmac platform drivers that do not open-code the clk_ptp_rate value
after having retrieved the default one from the device-tree can end up
with 0 in clk_ptp_rate (as clk_get_rate can return 0). It will
eventually propagate up to PTP initialization when bringing up the
interface, leading to a divide by 0:
Division by zero in kernel.
CPU: 1 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.12.30-00001-g48313bd5768a #22
Hardware name: STM32 (Device Tree Support)
Call trace:
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x6c/0x8c
dump_stack_lvl from Ldiv0_64+0x8/0x18
Ldiv0_64 from stmmac_init_tstamp_counter+0x190/0x1a4
stmmac_init_tstamp_counter from stmmac_hw_setup+0xc1c/0x111c
stmmac_hw_setup from __stmmac_open+0x18c/0x434
__stmmac_open from stmmac_open+0x3c/0xbc
stmmac_open from __dev_open+0xf4/0x1ac
__dev_open from __dev_change_flags+0x1cc/0x224
__dev_change_flags from dev_change_flags+0x24/0x60
dev_change_flags from ip_auto_config+0x2e8/0x11a0
ip_auto_config from do_one_initcall+0x84/0x33c
do_one_initcall from kernel_init_freeable+0x1b8/0x214
kernel_init_freeable from kernel_init+0x24/0x140
kernel_init from ret_from_fork+0x14/0x28
Exception stack(0xe0815fb0 to 0xe0815ff8)
Prevent this division by 0 by adding an explicit check and error log
about the actual issue. While at it, remove the same check from
stmmac_ptp_register, which then becomes duplicate
Fixes: 19d857c9038e ("stmmac: Fix calculations for ptp counters when clock input = 50Mhz.")
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Yanteng Si <si.yanteng@linux.dev>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250529-stmmac_tstamp_div-v4-1-d73340a794d5@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The MANA driver's probe registers netdevice via the following call chain:
mana_probe()
register_netdev()
register_netdevice()
register_netdevice() calls notifier callback for netvsc driver,
holding the netdev mutex via netdev_lock_ops().
Further this netvsc notifier callback end up attempting to acquire the
same lock again in dev_xdp_propagate() leading to deadlock.
netvsc_netdev_event()
netvsc_vf_setxdp()
dev_xdp_propagate()
This deadlock was not observed so far because net_shaper_ops was never set,
and thus the lock was effectively a no-op in this case. Fix this by using
netif_xdp_propagate() instead of dev_xdp_propagate() to avoid recursive
locking in this path.
And, since no deadlock is observed on the other path which is via
netvsc_probe, add the lock exclusivly for that path.
Also, clean up the unregistration path by removing the unnecessary call to
netvsc_vf_setxdp(), since unregister_netdevice_many_notify() already
performs this cleanup via dev_xdp_uninstall().
Fixes: 97246d6d21c2 ("net: hold netdev instance lock during ndo_bpf")
Cc: stable@vger.kernel.org
Signed-off-by: Saurabh Sengar <ssengar@linux.microsoft.com>
Tested-by: Erni Sri Satya Vennela <ernis@linux.microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Link: https://patch.msgid.link/1748513910-23963-1-git-send-email-ssengar@linux.microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix the signature of the net_devmem_bind_dmabuf API for
CONFIG_NET_DEVMEM=n.
Fixes: bd61848900bf ("net: devmem: Implement TX path")
Signed-off-by: Pranjal Shrivastava <praan@google.com>
Link: https://patch.msgid.link/20250528211058.1826608-1-praan@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
BRCM_LEG_PORT_ID was incorrectly used for pskb_may_pull length.
The correct check is BRCM_LEG_TAG_LEN + VLAN_HLEN, or 10 bytes.
Fixes: 964dbf186eaa ("net: dsa: tag_brcm: add support for legacy tags")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250529124406.2513779-1-noltari@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Mailbox operations are not possible while the driver is in reset.
Operations that require MBX exchange with the control plane will result
in long delays if executed while a reset is in progress:
ethtool -L <inf> combined 8& echo 1 > /sys/class/net/<inf>/device/reset
idpf 0000:83:00.0: HW reset detected
idpf 0000:83:00.0: Device HW Reset initiated
idpf 0000:83:00.0: Transaction timed-out (op:504 cookie:be00 vc_op:504 salt:be timeout:2000ms)
idpf 0000:83:00.0: Transaction timed-out (op:508 cookie:bf00 vc_op:508 salt:bf timeout:2000ms)
idpf 0000:83:00.0: Transaction timed-out (op:512 cookie:c000 vc_op:512 salt:c0 timeout:2000ms)
idpf 0000:83:00.0: Transaction timed-out (op:510 cookie:c100 vc_op:510 salt:c1 timeout:2000ms)
idpf 0000:83:00.0: Transaction timed-out (op:509 cookie:c200 vc_op:509 salt:c2 timeout:60000ms)
idpf 0000:83:00.0: Transaction timed-out (op:509 cookie:c300 vc_op:509 salt:c3 timeout:60000ms)
idpf 0000:83:00.0: Transaction timed-out (op:505 cookie:c400 vc_op:505 salt:c4 timeout:60000ms)
idpf 0000:83:00.0: Failed to configure queues for vport 0, -62
Disable mailbox communication in case of a reset, unless it's done during
a driver load, where the virtchnl operations are needed to configure the
device.
Fixes: 8077c727561aa ("idpf: add controlq init and reset checks")
Co-developed-by: Joshua Hay <joshua.a.hay@intel.com>
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Reviewed-by: Ahmed Zaki <ahmed.zaki@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add a helper function to correctly handle the lockless
synchronization when the sender needs to block. The paradigm is
if (no_resources()) {
stop_queue();
barrier();
if (!no_resources())
restart_queue();
}
netif_subqueue_maybe_stop already handles the paradigm correctly, but
the code split the check for resources in three parts, the first one
(descriptors) followed the protocol, but the other two (completions and
tx_buf) were only doing the first part and so race prone.
Luckily netif_subqueue_maybe_stop macro already allows you to use a
function to evaluate the start/stop conditions so the fix only requires
the right helper function to evaluate all the conditions at once.
The patch removes idpf_tx_maybe_stop_common since it's no longer needed
and instead adjusts separately the conditions for singleq and splitq.
Note that idpf_tx_buf_hw_update doesn't need to check for resources
since that will be covered in idpf_tx_splitq_frame.
To reproduce:
Reduce the threshold for pending completions to increase the chances of
hitting this pause by changing your kernel:
drivers/net/ethernet/intel/idpf/idpf_txrx.h
-#define IDPF_TX_COMPLQ_OVERFLOW_THRESH(txcq) ((txcq)->desc_count >> 1)
+#define IDPF_TX_COMPLQ_OVERFLOW_THRESH(txcq) ((txcq)->desc_count >> 4)
Use pktgen to force the host to push small pkts very aggressively:
./pktgen_sample02_multiqueue.sh -i eth1 -s 100 -6 -d $IP -m $MAC \
-p 10000-10000 -t 16 -n 0 -v -x -c 64
Fixes: 6818c4d5b3c2 ("idpf: add splitq start_xmit")
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Madhu Chittim <madhu.chittim@intel.com>
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Luigi Rizzo <lrizzo@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The current implementation of the Tx scheduler allows the tree to be
rebuilt as the user adds more Tx queues to the VSI. In such a case,
additional child nodes are added to the tree to support the new number
of queues.
Unfortunately, this algorithm does not take into account that the limit
of the VSI support node may be exceeded, so an additional node in the
VSI layer may be required to handle all the requested queues.
Such a scenario occurs when adding XDP Tx queues on machines with many
CPUs. Although the driver still respects the queue limit returned by
the FW, the Tx scheduler was unable to add those queues to its tree
and returned one of the errors below.
Such a scenario occurs when adding XDP Tx queues on machines with many
CPUs (e.g. at least 321 CPUs, if there is already 128 Tx/Rx queue pairs).
Although the driver still respects the queue limit returned by the FW,
the Tx scheduler was unable to add those queues to its tree and returned
the following errors:
Failed VSI LAN queue config for XDP, error: -5
or:
Failed to set LAN Tx queue context, error: -22
Fix this problem by extending the tree rebuild algorithm to check if the
current VSI node can support the requested number of queues. If it
cannot, create as many additional VSI support nodes as necessary to
handle all the required Tx queues. Symmetrically, adjust the VSI node
removal algorithm to remove all nodes associated with the given VSI.
Also, make the search for the next free VSI node more restrictive. That is,
add queue group nodes only to the VSI support nodes that have a matching
VSI handle.
Finally, fix the comment describing the tree update algorithm to better
reflect the current scenario.
Fixes: b0153fdd7e8a ("ice: update VSI config dynamically")
Reviewed-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Jesse Brandeburg <jbrandeburg@cloudflare.com>
Tested-by: Saritha Sanigani <sarithax.sanigani@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The current implementation of the Tx scheduler tree attempts
to create nodes for all Tx queues, ignoring the fact that some
queues may already exist in the tree. For example, if the VSI
already has 128 Tx queues and the user requests for 16 new queues,
the Tx scheduler will compute the tree for 272 queues (128 existing
queues + 144 new queues), instead of 144 queues (128 existing queues
and 16 new queues).
Fix that by modifying the node count calculation algorithm to skip
the queues that already exist in the tree.
Fixes: 5513b920a4f7 ("ice: Update Tx scheduler tree for VSI multi-Tx queue support")
Reviewed-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Jesse Brandeburg <jbrandeburg@cloudflare.com>
Tested-by: Saritha Sanigani <sarithax.sanigani@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When the XDP program is loaded, the XDP callback adds new Tx queues.
This means that the callback must update the Tx scheduler with the new
queue number. In the event of a Tx scheduler failure, the XDP callback
should also fail and roll back any changes previously made for XDP
preparation.
The previous implementation had a bug that not all changes made by the
XDP callback were rolled back. This caused the crash with the following
call trace:
[ +9.549584] ice 0000:ca:00.0: Failed VSI LAN queue config for XDP, error: -5
[ +0.382335] Oops: general protection fault, probably for non-canonical address 0x50a2250a90495525: 0000 [#1] SMP NOPTI
[ +0.010710] CPU: 103 UID: 0 PID: 0 Comm: swapper/103 Not tainted 6.14.0-net-next-mar-31+ #14 PREEMPT(voluntary)
[ +0.010175] Hardware name: Intel Corporation M50CYP2SBSTD/M50CYP2SBSTD, BIOS SE5C620.86B.01.01.0005.2202160810 02/16/2022
[ +0.010946] RIP: 0010:__ice_update_sample+0x39/0xe0 [ice]
[...]
[ +0.002715] Call Trace:
[ +0.002452] <IRQ>
[ +0.002021] ? __die_body.cold+0x19/0x29
[ +0.003922] ? die_addr+0x3c/0x60
[ +0.003319] ? exc_general_protection+0x17c/0x400
[ +0.004707] ? asm_exc_general_protection+0x26/0x30
[ +0.004879] ? __ice_update_sample+0x39/0xe0 [ice]
[ +0.004835] ice_napi_poll+0x665/0x680 [ice]
[ +0.004320] __napi_poll+0x28/0x190
[ +0.003500] net_rx_action+0x198/0x360
[ +0.003752] ? update_rq_clock+0x39/0x220
[ +0.004013] handle_softirqs+0xf1/0x340
[ +0.003840] ? sched_clock_cpu+0xf/0x1f0
[ +0.003925] __irq_exit_rcu+0xc2/0xe0
[ +0.003665] common_interrupt+0x85/0xa0
[ +0.003839] </IRQ>
[ +0.002098] <TASK>
[ +0.002106] asm_common_interrupt+0x26/0x40
[ +0.004184] RIP: 0010:cpuidle_enter_state+0xd3/0x690
Fix this by performing the missing unmapping of XDP queues from
q_vectors and setting the XDP rings pointer back to NULL after all those
queues are released.
Also, add an immediate exit from the XDP callback in case of ring
preparation failure.
Fixes: efc2214b6047 ("ice: Add support for XDP")
Reviewed-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Jesse Brandeburg <jbrandeburg@cloudflare.com>
Tested-by: Saritha Sanigani <sarithax.sanigani@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Depending on the security set the response to L2CAP_LE_CONN_REQ shall be
just L2CAP_CR_LE_ENCRYPTION if only encryption when BT_SECURITY_MEDIUM
is selected since that means security mode 2 which doesn't require
authentication which is something that is covered in the qualification
test L2CAP/LE/CFC/BV-25-C.
Link: https://github.com/bluez/bluez/issues/1270
Fixes: 27e2d4c8d28b ("Bluetooth: Add basic LE L2CAP connect request receiving support")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Commit 3d05fc82237a ("Bluetooth: qca: set power_ctrl_enabled on NULL
returned by gpiod_get_optional()") accidentally changed the prevous
behavior where power control would be disabled without the BT_EN GPIO
only on QCA_WCN6750 and QCA_WCN6855 while also getting the error check
wrong. We should treat every IS_ERR() return value from
devm_gpiod_get_optional() as a reason to bail-out while we should only
set power_ctrl_enabled to false on the two models mentioned above. While
at it: use dev_err_probe() to save a LOC.
Cc: stable@vger.kernel.org
Fixes: 3d05fc82237a ("Bluetooth: qca: set power_ctrl_enabled on NULL returned by gpiod_get_optional()")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Hsin-chen Chuang <chharry@chromium.org>
Reviewed-by: Hsin-chen Chuang <chharry@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Return value of devm_request_irq() must be checked (function is even
annotated) and without it clang W=1 complains:
btnxpuart.c:494:6: error: unused variable 'ret' [-Werror,-Wunused-variable]
Setting up wakeup IRQ handler is not really critical, because the
handler is empty, so just log the informational message so user could
submit proper bug report and silences the clang warning.
Fixes: c50b56664e48 ("Bluetooth: btnxpuart: Implement host-wakeup feature")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
In 'mgmt_hci_cmd_sync()', check whether the size of parameters passed
in 'struct mgmt_cp_hci_cmd_sync' matches the total size of the data
(i.e. 'sizeof(struct mgmt_cp_hci_cmd_sync)' plus trailing bytes).
Otherwise, large invalid 'params_len' will cause 'hci_cmd_sync_alloc()'
to do 'skb_put_data()' from an area beyond the one actually passed to
'mgmt_hci_cmd_sync()'.
Reported-by: syzbot+5fe2d5bfbfbec0b675a0@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=5fe2d5bfbfbec0b675a0
Fixes: 827af4787e74 ("Bluetooth: MGMT: Add initial implementation of MGMT_OP_HCI_CMD_SYNC")
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
If we sanitize error returns, the debug statements need
to come before that so that we don't lose information.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: 405b0d610745 ("net: usb: aqc111: fix error handling of usbnet read calls")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When running these commands on DUT (and similar at the other end)
ip link set dev eth0 up
ip link add link eth0 name eth0.10 type vlan id 10
ip addr add 10.0.0.1/24 dev eth0.10
ip link set dev eth0.10 up
ping 10.0.0.2
The ping will fail.
The reason why is failing is because, the network interfaces for lan966x
have a flag saying that the HW can insert the vlan tags into the
frames(NETIF_F_HW_VLAN_CTAG_TX). Meaning that the frames that are
transmitted don't have the vlan tag inside the skb data, but they have
it inside the skb. We already get that vlan tag and put it in the IFH
but the problem is that we don't configure the HW to rewrite the frame
when the interface is in host mode.
The fix consists in actually configuring the HW to insert the vlan tag
if it is different than 0.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Fixes: 6d2c186afa5d ("net: lan966x: Add vlan support.")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://patch.msgid.link/20250528093619.3738998-1-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The "freq" variable is in terms of MHz and "max_val_cycles" is in terms
of Hz. The fact that "max_val_cycles" is a u64 suggests that support
for high frequency is intended but the "freq_khz * 1000" would overflow
the u32 type if we went above 4GHz. Use unsigned long long type for the
mutliplication to prevent that.
Fixes: 31c128b66e5b ("net/mlx4_en: Choose time-stamping shift value according to HW frequency")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/aDbFHe19juIJKjsb@stanley.mountain
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Identify the cause of the suspend/resume hang: netif_carrier_off()
is called during link state changes and becomes stuck while
executing linkwatch_work().
To resolve this issue, call netif_device_detach() during the Ethernet
suspend process to temporarily detach the network device from the
kernel and prevent the suspend/resume hang.
Fixes: 8c7bd5a454ff ("net: ethernet: mtk-star-emac: new driver")
Signed-off-by: Yanqing Wang <ot_yanqing.wang@mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Link: https://patch.msgid.link/20250528075351.593068-1-macpaul.lin@mediatek.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
No driver should spam the kernel log when merely being loaded.
Fixes: 17fcb3dc12bbee8e ("hinic3: module initialization and tx/rx logic")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/5310dac0b3ab4bd16dd8fb761566f12e73b38cab.1748357352.git.geert+renesas@glider.be
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
syzbot reported a refcount warning [1] caused by calling get_net() on
a network namespace that is being destroyed (refcount=0). This happens
when a TIPC discovery timer fires during network namespace cleanup.
The recently added get_net() call in commit e279024617134 ("net/tipc:
fix slab-use-after-free Read in tipc_aead_encrypt_done") attempts to
hold a reference to the network namespace. However, if the namespace
is already being destroyed, its refcount might be zero, leading to the
use-after-free warning.
Replace get_net() with maybe_get_net(), which safely checks if the
refcount is non-zero before incrementing it. If the namespace is being
destroyed, return -ENODEV early, after releasing the bearer reference.
[1]: https://lore.kernel.org/all/68342b55.a70a0220.253bc2.0091.GAE@google.com/T/#m12019cf9ae77e1954f666914640efa36d52704a2
Reported-by: syzbot+f0c4a4aba757549ae26c@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/68342b55.a70a0220.253bc2.0091.GAE@google.com/T/#m12019cf9ae77e1954f666914640efa36d52704a2
Fixes: e27902461713 ("net/tipc: fix slab-use-after-free Read in tipc_aead_encrypt_done")
Signed-off-by: Charalampos Mitrodimas <charmitro@posteo.net>
Reviewed-by: Tung Nguyen <tung.quang.nguyen@est.tech>
Link: https://patch.msgid.link/20250527-net-tipc-warning-v2-1-df3dc398a047@posteo.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Fix the return value of none_validate_challenge() to be explicitly true
(which indicates the source packet should simply be discarded) rather than
implicitly true (because rxrpc_abort_conn() always returns -EPROTO which
gets converted to true).
Note that this change doesn't change the behaviour of the code (which is
correct by accident) and, in any case, we *shouldn't* get a CHALLENGE
packet to an rxnull connection (ie. no security).
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lists.infradead.org/pipermail/linux-afs/2025-April/009738.html
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Paolo Abeni <pabeni@redhat.com>
cc: Simon Horman <horms@kernel.org>
cc: linux-afs@lists.infradead.org
cc: netdev@vger.kernel.org
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/10720.1748358103@warthog.procyon.org.uk
Fixes: 5800b1cf3fd8 ("rxrpc: Allow CHALLENGEs to the passed to the app for a RESPONSE")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Previously, the RX_BUFFERS_POSTED stat incorrectly reported the
fill_cnt from RX queue 0 for all queues, resulting in inaccurate
per-queue statistics.
Fix this by correctly indexing priv->rx[idx].fill_cnt for each RX queue.
Fixes: 24aeb56f2d38 ("gve: Add Gvnic stats AQ command and ethtool show/set-priv-flags.")
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Link: https://patch.msgid.link/20250527130830.1812903-1-alok.a.tiwari@oracle.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
bus_id is currently derived from the ethernetX alias. If one is missing
for the device, 0 is used. If ethernet0 points to another stmmac device
or if there are 2+ stmmac devices without an ethernet alias, then bus_id
will be 0 for all of those.
This is an issue because the bus_id is used to generate the mdio bus id
(new_bus->id in drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
stmmac_mdio_register) and this needs to be unique.
This allows to avoid needing to define ethernet aliases for devices with
multiple stmmac controllers (such as the Rockchip RK3588) for multiple
stmmac devices to probe properly.
Obviously, the bus_id isn't guaranteed to be stable across reboots if no
alias is set for the device but that is easily fixed by simply adding an
alias if this is desired.
Fixes: 25c83b5c2e82 ("dt:net:stmmac: Add support to dwmac version 3.610 and 3.710")
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250527-stmmac-mdio-bus_id-v2-1-a5ca78454e3c@cherry.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
echo_skb_max should define the supported upper limit of echo_skb[]
allocated inside the netdevice's priv. The corresponding size value
provided by this driver to alloc_candev() is KVASER_PCIEFD_CAN_TX_MAX_COUNT
which is 17.
But later echo_skb_max is rounded up to the nearest power of two (for the
max case, that would be 32) and the tx/ack indices calculated further
during tx/rx may exceed the upper array boundary. Kasan reported this for
the ack case inside kvaser_pciefd_handle_ack_packet(), though the xmit
function has actually caught the same thing earlier.
BUG: KASAN: slab-out-of-bounds in kvaser_pciefd_handle_ack_packet+0x2d7/0x92a drivers/net/can/kvaser_pciefd.c:1528
Read of size 8 at addr ffff888105e4f078 by task swapper/4/0
CPU: 4 UID: 0 PID: 0 Comm: swapper/4 Not tainted 6.15.0 #12 PREEMPT(voluntary)
Call Trace:
<IRQ>
dump_stack_lvl lib/dump_stack.c:122
print_report mm/kasan/report.c:521
kasan_report mm/kasan/report.c:634
kvaser_pciefd_handle_ack_packet drivers/net/can/kvaser_pciefd.c:1528
kvaser_pciefd_read_packet drivers/net/can/kvaser_pciefd.c:1605
kvaser_pciefd_read_buffer drivers/net/can/kvaser_pciefd.c:1656
kvaser_pciefd_receive_irq drivers/net/can/kvaser_pciefd.c:1684
kvaser_pciefd_irq_handler drivers/net/can/kvaser_pciefd.c:1733
__handle_irq_event_percpu kernel/irq/handle.c:158
handle_irq_event kernel/irq/handle.c:210
handle_edge_irq kernel/irq/chip.c:833
__common_interrupt arch/x86/kernel/irq.c:296
common_interrupt arch/x86/kernel/irq.c:286
</IRQ>
Tx max count definitely matters for kvaser_pciefd_tx_avail(), but for seq
numbers' generation that's not the case - we're free to calculate them as
would be more convenient, not taking tx max count into account. The only
downside is that the size of echo_skb[] should correspond to the max seq
number (not tx max count), so in some situations a bit more memory would
be consumed than could be.
Thus make the size of the underlying echo_skb[] sufficient for the rounded
max tx value.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: 8256e0ca6010 ("can: kvaser_pciefd: Fix echo_skb race")
Cc: stable@vger.kernel.org
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Link: https://patch.msgid.link/20250528192713.63894-1-pchelkin@ispras.ru
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
syzbot reported a uaf in page_pool_recycle_in_ring:
BUG: KASAN: slab-use-after-free in lock_release+0x151/0xa30 kernel/locking/lockdep.c:5862
Read of size 8 at addr ffff8880286045a0 by task syz.0.284/6943
CPU: 0 UID: 0 PID: 6943 Comm: syz.0.284 Not tainted 6.13.0-rc3-syzkaller-gdfa94ce54f41 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0x241/0x360 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:378 [inline]
print_report+0x169/0x550 mm/kasan/report.c:489
kasan_report+0x143/0x180 mm/kasan/report.c:602
lock_release+0x151/0xa30 kernel/locking/lockdep.c:5862
__raw_spin_unlock_bh include/linux/spinlock_api_smp.h:165 [inline]
_raw_spin_unlock_bh+0x1b/0x40 kernel/locking/spinlock.c:210
spin_unlock_bh include/linux/spinlock.h:396 [inline]
ptr_ring_produce_bh include/linux/ptr_ring.h:164 [inline]
page_pool_recycle_in_ring net/core/page_pool.c:707 [inline]
page_pool_put_unrefed_netmem+0x748/0xb00 net/core/page_pool.c:826
page_pool_put_netmem include/net/page_pool/helpers.h:323 [inline]
page_pool_put_full_netmem include/net/page_pool/helpers.h:353 [inline]
napi_pp_put_page+0x149/0x2b0 net/core/skbuff.c:1036
skb_pp_recycle net/core/skbuff.c:1047 [inline]
skb_free_head net/core/skbuff.c:1094 [inline]
skb_release_data+0x6c4/0x8a0 net/core/skbuff.c:1125
skb_release_all net/core/skbuff.c:1190 [inline]
__kfree_skb net/core/skbuff.c:1204 [inline]
sk_skb_reason_drop+0x1c9/0x380 net/core/skbuff.c:1242
kfree_skb_reason include/linux/skbuff.h:1263 [inline]
__skb_queue_purge_reason include/linux/skbuff.h:3343 [inline]
root cause is:
page_pool_recycle_in_ring
ptr_ring_produce
spin_lock(&r->producer_lock);
WRITE_ONCE(r->queue[r->producer++], ptr)
//recycle last page to pool
page_pool_release
page_pool_scrub
page_pool_empty_ring
ptr_ring_consume
page_pool_return_page //release all page
__page_pool_destroy
free_percpu(pool->recycle_stats);
free(pool) //free
spin_unlock(&r->producer_lock); //pool->ring uaf read
recycle_stat_inc(pool, ring);
page_pool can be free while page pool recycle the last page in ring.
Add producer-lock barrier to page_pool_release to prevent the page
pool from being free before all pages have been recycled.
recycle_stat_inc() is empty when CONFIG_PAGE_POOL_STATS is not
enabled, which will trigger Wempty-body build warning. Add definition
for pool stat macro to fix warning.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/netdev/20250513083123.3514193-1-dongchenchen2@huawei.com
Fixes: ff7d6b27f894 ("page_pool: refurbish version of page_pool code")
Reported-by: syzbot+204a4382fcb3311f3858@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=204a4382fcb3311f3858
Signed-off-by: Dong Chenchen <dongchenchen2@huawei.com>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Reviewed-by: Mina Almasry <almasrymina@google.com>
Link: https://patch.msgid.link/20250527114152.3119109-1-dongchenchen2@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In mii_nway_restart() the code attempts to call
mii->mdio_read which is ch9200_mdio_read(). ch9200_mdio_read()
utilises a local buffer called "buff", which is initialised
with control_read(). However "buff" is conditionally
initialised inside control_read():
if (err == size) {
memcpy(data, buf, size);
}
If the condition of "err == size" is not met, then
"buff" remains uninitialised. Once this happens the
uninitialised "buff" is accessed and returned during
ch9200_mdio_read():
return (buff[0] | buff[1] << 8);
The problem stems from the fact that ch9200_mdio_read()
ignores the return value of control_read(), leading to
uinit-access of "buff".
To fix this we should check the return value of
control_read() and return early on error.
Reported-by: syzbot <syzbot+3361c2d6f78a3e0892f9@syzkaller.appspotmail.com>
Closes: https://syzkaller.appspot.com/bug?extid=3361c2d6f78a3e0892f9
Tested-by: syzbot <syzbot+3361c2d6f78a3e0892f9@syzkaller.appspotmail.com>
Fixes: 4a476bd6d1d9 ("usbnet: New driver for QinHeng CH9200 devices")
Cc: stable@vger.kernel.org
Signed-off-by: Qasim Ijaz <qasdev00@gmail.com>
Link: https://patch.msgid.link/20250526183607.66527-1-qasdev00@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When a process under memory pressure is not part of any cgroup and
the charged flag is false, trace_sock_exceed_buf_limit was not called
as expected.
This regression was introduced by commit 2def8ff3fdb6 ("sock:
Code cleanup on __sk_mem_raise_allocated()"). The fix changes the
default value of charged to true while preserving existing logic.
Fixes: 2def8ff3fdb6 ("sock: Code cleanup on __sk_mem_raise_allocated()")
Signed-off-by: Abel Wu <wuyun.abel@bytedance.com>
Signed-off-by: Tengteng Yang <yangtengteng@bytedance.com>
Link: https://patch.msgid.link/20250527030419.67693-1-yangtengteng@bytedance.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On linux-next, build for bpf selftest displays a warning:
Warning: Kernel ABI header at 'tools/include/uapi/linux/if_xdp.h'
differs from latest version at 'include/uapi/linux/if_xdp.h'.
Commit 8066e388be48 ("net: add UAPI to the header guard in various network headers")
changed the header guard from _LINUX_IF_XDP_H to _UAPI_LINUX_IF_XDP_H
in include/uapi/linux/if_xdp.h.
To resolve the warning, update tools/include/uapi/linux/if_xdp.h
to align with the changes in include/uapi/linux/if_xdp.h
Fixes: 8066e388be48 ("net: add UAPI to the header guard in various network headers")
Reported-by: Venkat Rao Bagalkote <venkat88@linux.ibm.com>
Closes: https://lore.kernel.org/all/c2bc466d-dff2-4d0d-a797-9af7f676c065@linux.ibm.com/
Tested-by: Venkat Rao Bagalkote <venkat88@linux.ibm.com>
Signed-off-by: Saket Kumar Bhaskar <skb99@linux.ibm.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://patch.msgid.link/20250527054138.1086006-1-skb99@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The script is supposed to skip wildcard interface testing if unsupported
by the host's nft tool. The failing check caused script abort due to
'set -e' though. Fix this by running the potentially failing nft command
inside the if-conditional pipe.
Fixes: 73db1b5dab6f ("selftests: netfilter: Torture nftables netdev hooks")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Link: https://patch.msgid.link/20250527094117.18589-1-phil@nwl.cc
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
We have noticed that when PHY timestamping is enabled, L2 frames seems
to be modified by changing two 2 bytes with a value of 0. The place were
these 2 bytes seems to be random(or I couldn't find a pattern). In most
of the cases the userspace can ignore these frames but if for example
those 2 bytes are in the correction field there is nothing to do. This
seems to happen when configuring the HW for IPv4 even that the flow is
not enabled.
These 2 bytes correspond to the UDPv4 checksum and once we don't enable
clearing the checksum when using L2 frames then the frame doesn't seem
to be changed anymore.
Fixes: 7d272e63e0979d ("net: phy: mscc: timestamping and PHC support")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://patch.msgid.link/20250523082716.2935895-1-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The unexpected MPLS packet may not end with the bottom label stack.
When there are many stacks, The label count value has wrapped around.
A dead loop occurs, soft lockup/CPU stuck finally.
stack backtrace:
UBSAN: array-index-out-of-bounds in /build/linux-0Pa0xK/linux-5.15.0/net/openvswitch/flow.c:662:26
index -1 is out of range for type '__be32 [3]'
CPU: 34 PID: 0 Comm: swapper/34 Kdump: loaded Tainted: G OE 5.15.0-121-generic #131-Ubuntu
Hardware name: Dell Inc. PowerEdge C6420/0JP9TF, BIOS 2.12.2 07/14/2021
Call Trace:
<IRQ>
show_stack+0x52/0x5c
dump_stack_lvl+0x4a/0x63
dump_stack+0x10/0x16
ubsan_epilogue+0x9/0x36
__ubsan_handle_out_of_bounds.cold+0x44/0x49
key_extract_l3l4+0x82a/0x840 [openvswitch]
? kfree_skbmem+0x52/0xa0
key_extract+0x9c/0x2b0 [openvswitch]
ovs_flow_key_extract+0x124/0x350 [openvswitch]
ovs_vport_receive+0x61/0xd0 [openvswitch]
? kernel_init_free_pages.part.0+0x4a/0x70
? get_page_from_freelist+0x353/0x540
netdev_port_receive+0xc4/0x180 [openvswitch]
? netdev_port_receive+0x180/0x180 [openvswitch]
netdev_frame_hook+0x1f/0x40 [openvswitch]
__netif_receive_skb_core.constprop.0+0x23a/0xf00
__netif_receive_skb_list_core+0xfa/0x240
netif_receive_skb_list_internal+0x18e/0x2a0
napi_complete_done+0x7a/0x1c0
bnxt_poll+0x155/0x1c0 [bnxt_en]
__napi_poll+0x30/0x180
net_rx_action+0x126/0x280
? bnxt_msix+0x67/0x80 [bnxt_en]
handle_softirqs+0xda/0x2d0
irq_exit_rcu+0x96/0xc0
common_interrupt+0x8e/0xa0
</IRQ>
Fixes: fbdcdd78da7c ("Change in Openvswitch to support MPLS label depth of 3 in ingress direction")
Signed-off-by: Faicker Mo <faicker.mo@zenlayer.com>
Acked-by: Ilya Maximets <i.maximets@ovn.org>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Link: https://patch.msgid.link/259D3404-575D-4A6D-B263-1DF59A67CF89@zenlayer.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
syzkaller reported a null-ptr-deref in txopt_get(). [0]
The offset 0x70 was of struct ipv6_txoptions in struct ipv6_pinfo,
so struct ipv6_pinfo was NULL there.
However, this never happens for IPv6 sockets as inet_sk(sk)->pinet6
is always set in inet6_create(), meaning the socket was not IPv6 one.
The root cause is missing validation in netlbl_conn_setattr().
netlbl_conn_setattr() switches branches based on struct
sockaddr.sa_family, which is passed from userspace. However,
netlbl_conn_setattr() does not check if the address family matches
the socket.
The syzkaller must have called connect() for an IPv6 address on
an IPv4 socket.
We have a proper validation in tcp_v[46]_connect(), but
security_socket_connect() is called in the earlier stage.
Let's copy the validation to netlbl_conn_setattr().
[0]:
Oops: general protection fault, probably for non-canonical address 0xdffffc000000000e: 0000 [#1] PREEMPT SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x0000000000000070-0x0000000000000077]
CPU: 2 UID: 0 PID: 12928 Comm: syz.9.1677 Not tainted 6.12.0 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014
RIP: 0010:txopt_get include/net/ipv6.h:390 [inline]
RIP: 0010:
Code: 02 00 00 49 8b ac 24 f8 02 00 00 e8 84 69 2a fd e8 ff 00 16 fd 48 8d 7d 70 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 53 02 00 00 48 8b 6d 70 48 85 ed 0f 84 ab 01 00
RSP: 0018:ffff88811b8afc48 EFLAGS: 00010212
RAX: dffffc0000000000 RBX: 1ffff11023715f8a RCX: ffffffff841ab00c
RDX: 000000000000000e RSI: ffffc90007d9e000 RDI: 0000000000000070
RBP: 0000000000000000 R08: ffffed1023715f9d R09: ffffed1023715f9e
R10: ffffed1023715f9d R11: 0000000000000003 R12: ffff888123075f00
R13: ffff88810245bd80 R14: ffff888113646780 R15: ffff888100578a80
FS: 00007f9019bd7640(0000) GS:ffff8882d2d00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f901b927bac CR3: 0000000104788003 CR4: 0000000000770ef0
PKRU: 80000000
Call Trace:
<TASK>
calipso_sock_setattr+0x56/0x80 net/netlabel/netlabel_calipso.c:557
netlbl_conn_setattr+0x10c/0x280 net/netlabel/netlabel_kapi.c:1177
selinux_netlbl_socket_connect_helper+0xd3/0x1b0 security/selinux/netlabel.c:569
selinux_netlbl_socket_connect_locked security/selinux/netlabel.c:597 [inline]
selinux_netlbl_socket_connect+0xb6/0x100 security/selinux/netlabel.c:615
selinux_socket_connect+0x5f/0x80 security/selinux/hooks.c:4931
security_socket_connect+0x50/0xa0 security/security.c:4598
__sys_connect_file+0xa4/0x190 net/socket.c:2067
__sys_connect+0x12c/0x170 net/socket.c:2088
__do_sys_connect net/socket.c:2098 [inline]
__se_sys_connect net/socket.c:2095 [inline]
__x64_sys_connect+0x73/0xb0 net/socket.c:2095
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xaa/0x1b0 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f901b61a12d
Code: 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 a8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f9019bd6fa8 EFLAGS: 00000246 ORIG_RAX: 000000000000002a
RAX: ffffffffffffffda RBX: 00007f901b925fa0 RCX: 00007f901b61a12d
RDX: 000000000000001c RSI: 0000200000000140 RDI: 0000000000000003
RBP: 00007f901b701505 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 0000000000000000 R14: 00007f901b5b62a0 R15: 00007f9019bb7000
</TASK>
Modules linked in:
Fixes: ceba1832b1b2 ("calipso: Set the calipso socket label to match the secattr.")
Reported-by: syzkaller <syzkaller@googlegroups.com>
Reported-by: John Cheung <john.cs.hey@gmail.com>
Closes: https://lore.kernel.org/netdev/CAP=Rh=M1LzunrcQB1fSGauMrJrhL6GGps5cPAKzHJXj6GQV+-g@mail.gmail.com/
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Link: https://patch.msgid.link/20250522221858.91240-1-kuniyu@amazon.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Reproduce the UAF scenario where netem is a child of HFSC and HFSC
is configured to use the eltree. In such case, this TDC test would
cause the HFSC class to be added to the eltree twice resulting
in a UAF.
Reviewed-by: Victor Nogueira <victor@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Link: https://patch.msgid.link/20250522181448.1439717-3-pctammela@mojatatu.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Savino says:
"We are writing to report that this recent patch
(141d34391abbb315d68556b7c67ad97885407547) [1]
can be bypassed, and a UAF can still occur when HFSC is utilized with
NETEM.
The patch only checks the cl->cl_nactive field to determine whether
it is the first insertion or not [2], but this field is only
incremented by init_vf [3].
By using HFSC_RSC (which uses init_ed) [4], it is possible to bypass the
check and insert the class twice in the eltree.
Under normal conditions, this would lead to an infinite loop in
hfsc_dequeue for the reasons we already explained in this report [5].
However, if TBF is added as root qdisc and it is configured with a
very low rate,
it can be utilized to prevent packets from being dequeued.
This behavior can be exploited to perform subsequent insertions in the
HFSC eltree and cause a UAF."
To fix both the UAF and the infinite loop, with netem as an hfsc child,
check explicitly in hfsc_enqueue whether the class is already in the eltree
whenever the HFSC_RSC flag is set.
[1] https://web.git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=141d34391abbb315d68556b7c67ad97885407547
[2] https://elixir.bootlin.com/linux/v6.15-rc5/source/net/sched/sch_hfsc.c#L1572
[3] https://elixir.bootlin.com/linux/v6.15-rc5/source/net/sched/sch_hfsc.c#L677
[4] https://elixir.bootlin.com/linux/v6.15-rc5/source/net/sched/sch_hfsc.c#L1574
[5] https://lore.kernel.org/netdev/8DuRWwfqjoRDLDmBMlIfbrsZg9Gx50DHJc1ilxsEBNe2D6NMoigR_eIRIG0LOjMc3r10nUUZtArXx4oZBIdUfZQrwjcQhdinnMis_0G7VEk=@willsroot.io/T/#u
Fixes: 37d9cf1a3ce3 ("sched: Fix detection of empty queues in child qdiscs")
Reported-by: Savino Dicanosa <savy@syst3mfailure.io>
Reported-by: William Liu <will@willsroot.io>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Tested-by: Victor Nogueira <victor@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Link: https://patch.msgid.link/20250522181448.1439717-2-pctammela@mojatatu.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This patch addresses below issues,
1. Active traffic on the leaf node must be stopped before its send queue
is reassigned to the parent. This patch resolves the issue by marking
the node as 'Inner'.
2. During a system reboot, the interface receives TC_HTB_LEAF_DEL
and TC_HTB_LEAF_DEL_LAST callbacks to delete its HTB queues.
In the case of TC_HTB_LEAF_DEL_LAST, although the same send queue
is reassigned to the parent, the current logic still attempts to update
the real number of queues, leadning to below warnings
New queues can't be registered after device unregistration.
WARNING: CPU: 0 PID: 6475 at net/core/net-sysfs.c:1714
netdev_queue_update_kobjects+0x1e4/0x200
Fixes: 5e6808b4c68d ("octeontx2-pf: Add support for HTB offload")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250522115842.1499666-1-hkelam@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
QOS is designed to create a new send queue whenever a class
is created, ensuring proper shaping and scheduling. However,
when multiple send queues are created and deleted in a loop,
SMMU errors are observed.
This patch addresses the issue by performing an data cache sync
during the teardown of QOS send queues.
Fixes: ab6dddd2a669 ("octeontx2-pf: qos send queues management")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250522094742.1498295-1-hkelam@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
To support Multi Vports on Bare metal, increase the device config response
version. And, skip the register HW vport, and register filter steps, when
the Bare metal hostmode is set.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Link: https://patch.msgid.link/1747671636-5810-1-git-send-email-haiyangz@microsoft.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Remove unused-but-set function and variable to fix the build warning:
arch/arm64/net/bpf_jit_comp.c: In function 'arch_bpf_trampoline_size':
2547 | int nregs, ret;
| ^~~~~
Fixes: 9014cf56f13d ("bpf, arm64: Support up to 12 function arguments")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Xu Kuohai <xukuohai@huawei.com>
Link: https://lore.kernel.org/bpf/20250528002704.21197-1-alexei.starovoitov@gmail.com
Closes: https://lore.kernel.org/oe-kbuild-all/202505280643.h0qYcSCM-lkp@intel.com/
|
|
This variable is unused and can be removed.
Signed-off-by: Mina Almasry <almasrymina@google.com>
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250523230524.1107879-9-almasrymina@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The current test just sends "hello\nworld" and verifies that is the
string received on the RX side. That is fine, but improve the test a bit
by sending 1K data. The test should be improved further to send more
data, but for now this should be a welcome improvement.
The test will send a repeating pattern of 0x01, 0x02, ... 0x06. The
ncdevmem `-v 7` flag will verify this pattern. ncdevmem will provide
useful debugging info when the test fails, such as the frags received
and verified fine, and which frag exactly failed, what was the expected
byte pattern, and what is the actual byte pattern received. All this
debug information will be useful when the test fails.
Signed-off-by: Mina Almasry <almasrymina@google.com>
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250523230524.1107879-8-almasrymina@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ncdevmem supports drivers that are limited to either 3-tuple or 5-tuple
FS support, but the ksft is currently 3-tuple only. Support drivers that
have 5-tuple FS supported by adding a ksft arg.
Signed-off-by: Mina Almasry <almasrymina@google.com>
fix 5-tuple
fix 5-tuple
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250523230524.1107879-7-almasrymina@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
Lorenzo Bianconi
Bui Quang Minh
Ronak Doshi
Jakub Kicinski
Jinjian Song
Shiming Cheng
Paul Chaignon
Alexis Lothoré
Saurabh Sengar
Pranjal Shrivastava
Álvaro Fernández Rojas
Emil Tantilov
Brian Vazquez
Michal Kubiak
Luiz Augusto von Dentz
Bartosz Golaszewski
Krzysztof Kozlowski
Dmitry Antipov
Oliver Neukum
Horatiu Vultur
Dan Carpenter
Yanqing Wang
Geert Uytterhoeven
Charalampos Mitrodimas
David Howells
Alok Tiwari
Quentin Schulz
Fedor Pchelkin
Dong Chenchen
Qasim Ijaz
Tengteng Yang
Saket Kumar Bhaskar
Phil Sutter
Faicker Mo
Kuniyuki Iwashima
Pedro Tammela
Hariprasad Kelam
Haiyang Zhang
Alexei Starovoitov
Mina Almasry