| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Odroid-XU4 has a RTL8153-CG gigabit Ethernet adapter, connected over
USB 3.0.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
The Marvell WiFi-Ex driver tries to load a firmware on probe. So if the
driver is built-in and probed before a firmware is available, this is
not loaded and the chip does not work.
This happens for example if an initramfs isn't used since the driver is
probed before the root filesystem is mounted.
Change the default config since the driver isn't needed for machines to
boot and is more convenient to have it enabled as a module to avoid
requiring an initramfs or to have the firmware built into the kernel.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
The simplefb driver allows the kernel to render on a pre-allocated
buffer that's been initialized by firmware before the kernel boots.
This option was enabled to have display working on the Exynos5250
Snow Chromebook by commit da9d0fbf5e9a ("ARM: exynos: defconfig
update") since proper DRM/KMS support did not exist at that time.
But now that the Exynos DRM driver has support for this hardware,
there is no need to have simplefb enabled. In fact, if a user has
a u-boot that injects the simplefb dev node to the FDT before pass
it to the kernel, display won't be properly initialized and only a
blank screen will be shown since there isn't a proper handoff from
the simplefb driver to the Exynos DRM driver.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Michael Turquette <mturquette@baylibre.com>
Tested-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Odroid XU3 family boards come with RGB LEDs. Enabling LEDS_GPIO and
LEDS_PWM allows monitoring the board alive state (heartbeat) and
MMC/SDcard IO usage.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
[k.kozlowski: Rewritten the commit message]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
DWC2 (s3c-hsotg) hardware module is available on many Exynos based boards,
so enable DWC2 driver as well as the most common USB Ethernet gadget.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
DWC2 (s3c-hsotg) hardware module is available on many Exynos based boards,
so enable DWC2 driver as well as the most common USB Ethernet gadget.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
The Exynos5420 Peach Pit and Exynos5800 Peach Pi boards have a built-in
Silicon Motion USB UVC WebCam. Enable support for the USB Video Class
driver and its needed media Kconfig symbols so the camera is supported.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Some drivers used on a Marvell Berlin kernel were missing from
multi_v7_defconfig. This series add them:
* The pxa168 Ethernet driver is added as a loadable module.
* The Berlin ADC driver is added as a loadable module.
* Both the Berlin USB PHY and SATA PHY drivers are added,
built-in, as they are required for the already available USB
and SATA functionalities in multi_v7_defconfig.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Enable some options that have recently been enabled on Tegra platforms:
* TOUCHSCREEN_WM97XX: touchscreen support on Toradex Colibri
* SND_SOC_TEGRA_WM9712: audio support on Toradex Colibri
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The AT91 SDHCI device has been introduced with Atmel SAMA5D2 SoC.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The Flexcom device has been introduced with Atmel SAMA5D2 SoC.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Add Atmel SAMA5D2 SoC family to multi_v7 image.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Add SAMA5D2 SoC plus Atmel flexcom and Atmel sdhci devices.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Trivial savedefconfig update.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Trivial savedefconfig update.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
CONFIG_FIXED_PHY is needed to have Ethernet working on STi boards.
Select it as built-in since RootFS is accessible from NFS on these boards.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
- Enable SPIFI Flash and JFFS2 to support rootfs on Flash memory
- Enable USB Phy, mass storage and SCSI to support USB memory
- Enable PCF857x and JC42 I2C devices found on Hitex board
- Enable PL172 to support memory mapped NOR Flash
- New LPC18xx drivers: I2C, Watchdog, SCT PWM and RTC
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Enable fpga manager framework and low level driver for
socfpga in socfpga_defconfig
Signed-off-by: Alan Tull <atull@opensource.altera.com>
Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
|
|
Actviate HDMI output of the RCar DU (and LVDS while we are here).
Enable the HDMI encoder chip found on Lager/Koelsch boards.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch enables the following options needed by the Seagate
Personal Cloud 1 and 2-Bay and the Seagate NAS 2 and 4-Bay:
SATA_AHCI
POWER_RESET_GPIO
RTC_DRV_DS1307
RTC_DRV_PCF8563
Additionnally this patch also enables NEW_LEDS which was missing for
some reasons.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Actviate HDMI output of the RCar DU (and LVDS while we are here).
Enable the HDMI encoder chip found on Lager/Koelsch boards.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch enables a number of devices currently supported by the MSM8916
boards. These include I2C, SPI, DMA, SMEM, SMD, and SMD regulator support.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This patch enables all of the options necessary to support the Qualcomm SMD
RPM regulator driver.
Signed-off-by: Andy Gross <agross@codeaurora.org>
|
|
This patch enables all of the options required to support SMD RPM based
regulators.
Signed-off-by: Andy Gross <agross@codeaurora.org>
|
|
Similar to the power management situation on Rockchip boards, there are
two common RTC setups. For boards using the RK808 chip as a PMIC that
chip also serves as the RTC, while boards using the ACT8846 typically use
the Haoyu Microelectronics HYM8563 chip as their RTC.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Most Rockchip SoCs have a DesignWare HS OTG USB 2.0 controller, enable
the driver for the Rockchip USB 2.0 PHY to make that functional.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Enable options needed for HDMI out on rockchip: DRM driver, Rockchip
DesignWare HDMI glue and the rockchip IOMMU (dependency of the DRM
driver).
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Rockchip boards seem to have two common regulator setups. Various board
used the Active Semi act8846 often in combination with Silergy syr82x
regulators (e.g. Radxa Rock Pro/Rock 2, Firefly, and Netxeon R89 etc),
while others use regulator part of the Rockchip RK808 chip (e.g. the
various Veyron based chromebooks, Chipspark Popmetal etc)
Enable all these regulators.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Enable Rockchip I2C, SPI, PWM, thermal drivers.
Builtin are I2C (as it often required to control the pmic) and Thermal
drivers (to prevent thermal damage). SPI and PWM drivers configured as
modules
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This patch adds few missing essential configs in the multi_v7_defconf,
absense of some configs like PINCTRL_APQ8064 would prevent the board from
getting access to serial.
cc: Kevin Hilman <khilman@kernel.org>
cc: Tyler Baker <tyler.baker@linaro.org>
Tested-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
|
|
The MIPS syscall handler code used to return -ENOSYS on invalid
syscalls. Whilst this is expected, it caused problems for seccomp
filters because the said filters never had the change to run since
the code returned -ENOSYS before triggering them. This caused
problems on the chromium testsuite for filters looking for invalid
syscalls. This has now changed and the seccomp filters are always
run even if the syscall is invalid. We return -ENOSYS once we
return from the seccomp filters. Moreover, similar codepaths have
been merged in the process which simplifies somewhat the overall
syscall code.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11236/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This patch fixes one cases where abs() was being used with 64-bit
nanosecond values, where the result may be capped at 32-bits.
This potentially could cause watchdog false negatives on 32-bit
systems, so this patch addresses the issue by using abs64().
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1442279124-7309-2-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
When configuring the interrupt mapping for a new device, we
iterate over all the possible aliases to account for their
maximum MSI allocation. This was introduced by e8137f4f5088
("irqchip: gicv3-its: Iterate over PCI aliases to generate ITS configuration").
Turns out that the code doing that is a bit braindead, and repeatedly
accounts for the same device over and over.
Fix this by counting the actual alias that is passed to us by the
core code.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Alex Shi <alex.shi@linaro.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1443800646-8074-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
More agressive inlining in recent versions of GCC have uncovered
a new set of warnings:
drivers/irqchip/irq-gic-v3-its.c: In function its_msi_prepare:
drivers/irqchip/irq-gic-v3-its.c:1148:26: warning: lpi_base may be used
uninitialized in this function [-Wmaybe-uninitialized]
dev->event_map.lpi_base = lpi_base;
^
drivers/irqchip/irq-gic-v3-its.c:1116:6: note: lpi_base was declared here
int lpi_base;
^
drivers/irqchip/irq-gic-v3-its.c:1149:25: warning: nr_lpis may be used
uninitialized in this function [-Wmaybe-uninitialized]
dev->event_map.nr_lpis = nr_lpis;
^
drivers/irqchip/irq-gic-v3-its.c:1117:6: note: nr_lpis was declared here
int nr_lpis;
^
The warning is fairly benign (there is no code path that could
actually use uninitialized variables), but let's silence it anyway
by zeroing the variables on the error path.
Reported-by: Alex Shi <alex.shi@linaro.org>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1443800646-8074-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
This reverts commit e51e38494a8ecc18650efb0c840600637891de2c: we
actually do want the device to work in extended W mode, as this is the
mode that allows us receiving multiple contact information.
Cc: stable@vger.kernel.org
|
|
During development it was found that a number of builds would panic
during the kernel init process, more specifically in 'delayed_fput()'.
The panic showed the kernel trying to access a memory address of
'0xb7fdc00' while traversing the 'delayed_fput_list' structure.
Comparing this memory address to the value of the pointer used on
builds that did not panic confirmed that the pointer on crashing
builds must have been corrupted at some stage earlier in the init
process.
By traversing the list earlier and earlier in the code it was found
that 'plat_mem_setup()' was responsible for corrupting the list.
Specifically the line:
memory = cvmx_bootmem_phy_alloc(mem_alloc_size,
__pa_symbol(&__init_end), -1,
0x100000,
CVMX_BOOTMEM_FLAG_NO_LOCKING);
Which would eventually call:
cvmx_bootmem_phy_set_size(new_ent_addr,
cvmx_bootmem_phy_get_size
(ent_addr) -
(desired_min_addr -
ent_addr));
Where 'new_ent_addr'=0x4800000 (the address of 'delayed_fput_list')
and the second argument (size)=0xb7fdc00 (the address causing the
kernel panic). The job of this part of 'plat_mem_setup()' is to
allocate chunks of memory for the kernel to use. At the start of
each chunk of memory the size of the chunk is written, hence the
value 0xb7fdc00 is written onto memory at 0x4800000, therefore the
kernel panics when it goes back to access 'delayed_fput_list' later
on in the initialisation process.
On builds that were not crashing it was found that the compiler had
placed 'delayed_fput_list' at 0x4800008, meaning it wasn't corrupted
(but something else in memory was overwritten).
As can be seen in the first function call above the code begins to
allocate chunks of memory beginning from the symbol '__init_end'.
The MIPS linker script (vmlinux.lds.S) however defines the .bss
section to begin after '__init_end'. Therefore memory within the
.bss section is allocated to the kernel to use (System.map shows
'delayed_fput_list' and other kernel structures to be in .bss).
To stop the kernel panic (and the .bss section being corrupted)
memory should begin being allocated from the symbol '_end'.
Signed-off-by: Matt Bennett <matt.bennett@alliedtelesis.co.nz>
Acked-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: aleksey.makarov@auriga.com
Patchwork: https://patchwork.linux-mips.org/patch/11251/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Commit 1a3d59579b9f ("MIPS: Tidy up FPU context switching") removed FP
context saving from the asm-written resume function in favour of reusing
existing code to perform the same task. However it only removed the FP
context saving code from the r4k_switch.S implementation of resume.
Remove it from the r2300_switch.S implementation too in order to prevent
attempting to save the FP context twice, which would likely lead to an
exception from the second save because the FPU had already been disabled
by the first save.
This patch has only been build tested, using rbtx49xx_defconfig.
Fixes: 1a3d59579b9f ("MIPS: Tidy up FPU context switching")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-kernel@vger.kernel.org
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/11167/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Commit 1a3d59579b9f ("MIPS: Tidy up FPU context switching") removed FP
context saving from the asm-written resume function in favour of reusing
existing code to perform the same task. However it only removed the FP
context saving code from the r4k_switch.S implementation of resume.
Octeon uses its own implementation in octeon_switch.S, so remove FP
context saving there too in order to prevent attempting to save context
twice. That formerly led to an exception from the second save as follows
because the FPU had already been disabled by the first save:
do_cpu invoked from kernel context![#1]:
CPU: 0 PID: 2 Comm: kthreadd Not tainted 4.3.0-rc2-dirty #2
task: 800000041f84a008 ti: 800000041f864000 task.ti: 800000041f864000
$ 0 : 0000000000000000 0000000010008ce1 0000000000100000 ffffffffbfffffff
$ 4 : 800000041f84a008 800000041f84ac08 800000041f84c000 0000000000000004
$ 8 : 0000000000000001 0000000000000000 0000000000000000 0000000000000001
$12 : 0000000010008ce3 0000000000119c60 0000000000000036 800000041f864000
$16 : 800000041f84ac08 800000000792ce80 800000041f84a008 ffffffff81758b00
$20 : 0000000000000000 ffffffff8175ae50 0000000000000000 ffffffff8176c740
$24 : 0000000000000006 ffffffff81170300
$28 : 800000041f864000 800000041f867d90 0000000000000000 ffffffff815f3fa0
Hi : 0000000000fa8257
Lo : ffffffffe15cfc00
epc : ffffffff8112821c resume+0x9c/0x200
ra : ffffffff815f3fa0 __schedule+0x3f0/0x7d8
Status: 10008ce2 KX SX UX KERNEL EXL
Cause : 1080002c (ExcCode 0b)
PrId : 000d0601 (Cavium Octeon+)
Modules linked in:
Process kthreadd (pid: 2, threadinfo=800000041f864000, task=800000041f84a008, tls=0000000000000000)
Stack : ffffffff81604218 ffffffff815f7e08 800000041f84a008 ffffffff811681b0
800000041f84a008 ffffffff817e9878 0000000000000000 ffffffff81770000
ffffffff81768340 ffffffff81161398 0000000000000001 0000000000000000
0000000000000000 ffffffff815f4424 0000000000000000 ffffffff81161d68
ffffffff81161be8 0000000000000000 0000000000000000 0000000000000000
0000000000000000 0000000000000000 0000000000000000 ffffffff8111e16c
0000000000000000 0000000000000000 0000000000000000 0000000000000000
0000000000000000 0000000000000000 0000000000000000 0000000000000000
0000000000000000 0000000000000000 0000000000000000 0000000000000000
0000000000000000 0000000000000000 0000000000000000 0000000000000000
...
Call Trace:
[<ffffffff8112821c>] resume+0x9c/0x200
[<ffffffff815f3fa0>] __schedule+0x3f0/0x7d8
[<ffffffff815f4424>] schedule+0x34/0x98
[<ffffffff81161d68>] kthreadd+0x180/0x198
[<ffffffff8111e16c>] ret_from_kernel_thread+0x14/0x1c
Tested using cavium_octeon_defconfig on an EdgeRouter Lite.
Fixes: 1a3d59579b9f ("MIPS: Tidy up FPU context switching")
Reported-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Aleksey Makarov <aleksey.makarov@auriga.com>
Cc: linux-kernel@vger.kernel.org
Cc: Chandrakala Chavva <cchavva@caviumnetworks.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Leonid Rosenboim <lrosenboim@caviumnetworks.com>
Patchwork: https://patchwork.linux-mips.org/patch/11166/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
When function graph tracer is enabled, the following operation
will trigger panic:
mount -t debugfs nodev /sys/kernel
echo next_tgid > /sys/kernel/tracing/set_ftrace_filter
echo function_graph > /sys/kernel/tracing/current_tracer
ls /proc/
------------[ cut here ]------------
[ 198.501417] Unable to handle kernel paging request at virtual address cb88537fdc8ba316
[ 198.506126] pgd = ffffffc008f79000
[ 198.509363] [cb88537fdc8ba316] *pgd=00000000488c6003, *pud=00000000488c6003, *pmd=0000000000000000
[ 198.517726] Internal error: Oops: 94000005 [#1] SMP
[ 198.518798] Modules linked in:
[ 198.520582] CPU: 1 PID: 1388 Comm: ls Tainted: G
[ 198.521800] Hardware name: linux,dummy-virt (DT)
[ 198.522852] task: ffffffc0fa9e8000 ti: ffffffc0f9ab0000 task.ti: ffffffc0f9ab0000
[ 198.524306] PC is at next_tgid+0x30/0x100
[ 198.525205] LR is at return_to_handler+0x0/0x20
[ 198.526090] pc : [<ffffffc0002a1070>] lr : [<ffffffc0000907c0>] pstate: 60000145
[ 198.527392] sp : ffffffc0f9ab3d40
[ 198.528084] x29: ffffffc0f9ab3d40 x28: ffffffc0f9ab0000
[ 198.529406] x27: ffffffc000d6a000 x26: ffffffc000b786e8
[ 198.530659] x25: ffffffc0002a1900 x24: ffffffc0faf16c00
[ 198.531942] x23: ffffffc0f9ab3ea0 x22: 0000000000000002
[ 198.533202] x21: ffffffc000d85050 x20: 0000000000000002
[ 198.534446] x19: 0000000000000002 x18: 0000000000000000
[ 198.535719] x17: 000000000049fa08 x16: ffffffc000242efc
[ 198.537030] x15: 0000007fa472b54c x14: ffffffffff000000
[ 198.538347] x13: ffffffc0fada84a0 x12: 0000000000000001
[ 198.539634] x11: ffffffc0f9ab3d70 x10: ffffffc0f9ab3d70
[ 198.540915] x9 : ffffffc0000907c0 x8 : ffffffc0f9ab3d40
[ 198.542215] x7 : 0000002e330f08f0 x6 : 0000000000000015
[ 198.543508] x5 : 0000000000000f08 x4 : ffffffc0f9835ec0
[ 198.544792] x3 : cb88537fdc8ba316 x2 : cb88537fdc8ba306
[ 198.546108] x1 : 0000000000000002 x0 : ffffffc000d85050
[ 198.547432]
[ 198.547920] Process ls (pid: 1388, stack limit = 0xffffffc0f9ab0020)
[ 198.549170] Stack: (0xffffffc0f9ab3d40 to 0xffffffc0f9ab4000)
[ 198.582568] Call trace:
[ 198.583313] [<ffffffc0002a1070>] next_tgid+0x30/0x100
[ 198.584359] [<ffffffc0000907bc>] ftrace_graph_caller+0x6c/0x70
[ 198.585503] [<ffffffc0000907bc>] ftrace_graph_caller+0x6c/0x70
[ 198.586574] [<ffffffc0000907bc>] ftrace_graph_caller+0x6c/0x70
[ 198.587660] [<ffffffc0000907bc>] ftrace_graph_caller+0x6c/0x70
[ 198.588896] Code: aa0003f5 2a0103f4 b4000102 91004043 (885f7c60)
[ 198.591092] ---[ end trace 6a346f8f20949ac8 ]---
This is because when using function graph tracer, if the traced
function return value is in multi regs ([x0-x7]), return_to_handler
may corrupt them. So in return_to_handler, the parameter regs should
be protected properly.
Cc: <stable@vger.kernel.org> # 3.18+
Signed-off-by: Li Bin <huawei.libin@huawei.com>
Acked-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
The entire bpf_jit_asm.S is written in noreorder mode because "we know
better" according to a comment. This also prevented the assembler from
throwing in the required NOPs for MIPS I processors which have no
load-use interlock, thus the load's consumer might end up using the
old value of the register from prior to the load.
Fixed by putting the assembler in reorder mode for just the affected
load instructions. This is not enough for gas to actually try to be
clever by looking at the next instruction and inserting a nop only
when needed but as the comment said "we know better", so getting gas
to unconditionally emit a NOP is just right in this case and prevents
adding further ifdefery.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
On x32, gcc predefines __x86_64__ but long is only 32-bit. Use
__ILP32__ to distinguish x32.
Fixes this compiler error in perf:
tools/include/asm-generic/bitops/__ffs.h: In function '__ffs':
tools/include/asm-generic/bitops/__ffs.h:19:8: error: right shift count >= width of type [-Werror=shift-count-overflow]
word >>= 32;
^
This isn't sufficient to build perf for x32, though.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/1443660043.2730.15.camel@decadent.org.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Passing -1 to bitmap_storage_alloc() causes page->index to be set to
-1, which is quite problematic.
So only pass ->cluster_slot if mddev_is_clustered().
Fixes: b97e92574c0b ("Use separate bitmaps for each nodes in the cluster")
Cc: stable@vger.kernel.org (v4.1+)
Signed-off-by: NeilBrown <neilb@suse.com>
|
|
close_sync() needs to set conf->next_resync to a large, but safe value
below MaxSector and use it to determine whether or not to set
start_next_window in wait_barrier()
Solution suggested by Neil Brown.
Reported-by: Nate Dailey <nate.dailey@stratus.com>
Tested-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
|
|
Remove unneeded NULL test.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@ expression x; @@
-if (x != NULL)
\(kmem_cache_destroy\|mempool_destroy\|dma_pool_destroy\)(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NeilBrown <neilb@suse.com>
|
|
If faulty disks of an array are more than allowed degraded number, the
array enters error handling. It will be marked as read-only with
MD_CHANGE_PENDING/RECOVERY_NEEDED set. But currently recovery doesn't
clear CHANGE_PENDING bit for read-only array. If MD_CHANGE_PENDING is
set for a raid5 array, all returned IO will be hold on a list till the
bit is clear. But recovery nevery clears this bit, the IO is always in
pending state and nevery finish. This has bad effects like upper layer
can't get an IO error and the array can't be stopped.
Fixes: c3cce6cda162 ("md/raid5: ensure device failure recorded before write request returns.")
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: NeilBrown <neilb@suse.com>
|
|
Calling e.g. blk_queue_max_hw_sectors() after calls to
disk_stack_limits() discards the settings determined by
disk_stack_limits().
So we need to make those calls first.
Fixes: 199dc6ed5179 ("md/raid0: update queue parameter in a safer location.")
Cc: stable@vger.kernel.org (v2.6.35+ - please apply with 199dc6ed5179).
Reported-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
|
|
When need_this_block probably shouldn't be called when there
are more than 2 failed devices, we really don't want it to try
indexing beyond the end of the failed_num[] of fdev[] arrays.
So limit the loops to at most 2 iterations.
Reported-by: Shaohua Li <shli@fb.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
handle_failed_stripe() makes the stripe fail, eg, all IO will return
with a failure, but it doesn't update stripe_head_state. Later
handle_stripe() has special handling for raid6 for handle_stripe_fill().
That check before handle_stripe_fill() doesn't skip the failed stripe
and we get a kernel crash in need_this_block. This patch clear the
analysis state to make sure no functions wrongly called after
handle_failed_stripe()
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: NeilBrown <neilb@suse.com>
|
|
If a superblock update is pending, wait for it to complete before
letting md_set_readonly() switch to readonly.
Otherwise we might lose important information about a device having
failed.
For external arrays, waiting for superblock updates can wait on
user-space, so in that case, just return an error.
Reported-and-tested-by: Shaohua Li <shli@fb.com>
Signed-off-by: NeilBrown <neilb@suse.com>
|
Anand Moon
Javier Martinez Canillas
Marek Szyprowski
Antoine Tenart
Thierry Reding
Ludovic Desroches
Maxime Coquelin
Joachim Eastwood
Alan Tull
Wolfram Sang
Simon Guinot
Andy Gross
Sjoerd Simons
Srinivas Kandagatla
Linus Torvalds
Markos Chandras
John Stultz
Marc Zyngier
Dmitry Torokhov
Matt Bennett
Paul Burton
Li Bin
Ralf Baechle
Ben Hutchings
NeilBrown
Jes Sorensen
Julia Lawall
Shaohua Li