aboutsummaryrefslogtreecommitdiffstatshomepage
path: root/tools/perf/scripts/python/call-graph-from-postgresql.py (unfollow)
AgeCommit message (Collapse)AuthorFilesLines
2015-10-17ARM: dts: sunxi: Fix interrupt-cells for [r]pio on A23/A31/A33/A80Hans de Goede3-2/+3
When the gpio interrupt bindings where changed to add a bank to the specifier list, the r_pio nodes of A23/A31/A33 where not updated to match and neither was the pio node of the A80, this fixes this. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-10-16ARM: dts: sun8i: Add NMI interrupt controller nodeChen-Yu Tsai1-0/+8
The NMI interrupt controller is in charge of the NMI pin exposed by the SoC to the PMIC. The PMIC signals interrupts through this. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-10-13ARM: dts: sun6i: hummingbird: Enable AXP221 DC5LDO regulator as "vdd-cpus"Chen-Yu Tsai1-0/+6
The DC5LDO regulator supplies VDD-CPUS, which is for the embedded controller in the A31 SoC. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-10-13ARM: dts: sun6i: hummingbird: Use axp22x.dtsi for AXP221 regulatorsChen-Yu Tsai1-57/+56
Now that we have axp22x.dtsi describing common axp22x hardware, use it and reference the nodes instead of declaring the whole tree. Also drop the "always-on" from the vdd-gpu regulator, since we don't support the GPU anyway. And add a regulator reference for cpu0. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-10-13ARM: dts: sun6i: hummingbird: Fix VDD-CPU and VDD-GPU regulator namesChen-Yu Tsai1-4/+4
The VDD-CPU and VDD-GPU regulators were incorrectly swapped. Fixes: bab03561224ba ("ARM: dts: sun6i: hummingbird: Add AXP221 regulator nodes") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-10-13ARM: dts: sun7i: Add regulator configuration for pcDuino v3 NanoAdam Sampson1-4/+31
The power configuration on this board is the same as the pcDuino v3. This will enable frequency/voltage scaling over the standard A20 operating points from 144 MHz to 960 MHz. Tested using cpufreq-ljt-stress-test on two pcDuino v3 Nano boards; also tested successfully with voltages reduced by 0.025 V. Signed-off-by: Adam Sampson <ats@offog.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-10-13ARM: dts: sun6i: Turn on gmac on ColombusHans de Goede1-0/+12
We've everything we need to support the gmac on Colombus, turn it on. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-10-13ARM: dts: sun8i: Make et-q8-v1.6.dts a symlink to q8-tablet.dtsHans de Goede1-88/+1
A33 Q8 tablets with the et-q8-v1.6 pcb will work fine with the generic q8-tablet.dts and given the many variants of PCBs found in Q8 tablets using such a specific dts name was a mistake in hindsight. We cannot just drop the et-q8-v1.6.dtb as existing u-boot configs may very well point to it. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-10-13ARM: dts: sun8i: Make ippo-q8h-v*.dts a symlink to q8-tablet.dtsHans de Goede2-128/+2
A23 Q8 tablets with the ippo-q8h-v* pcb will work fine with the generic q8-tablet.dts and given the many variants of PCBs found in Q8 tablets using such a specific dts name was a mistake in hindsight. We cannot just drop the ippo-q8h-v*.dtb as existing u-boot configs may very well point to it. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-10-13ARM: dts: sun8i: Add sun8i-a23-q8-tablet.dts fileHans de Goede2-0/+66
This is a generic dts file for A23 based q8 formfactor tablets, this is intended to replace both sun8i-a23-ippo-q8h-v5.dts and sun8i-a23-ippo-q8h-v1.2.dts (these can be fully dropped after a transition period). Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-10-12ARM: dts: sun5i: Add backlight node to sun5i-q8-common.dtsiHans de Goede1-0/+10
All A13 based q8 formfactor tablets use the same backlight setup, add a backlight devicetree node for controlling the backlight on these devices. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-10-12ARM: dts: sunxi: Enable PWM controller on Q8 format tabletsChen-Yu Tsai1-0/+6
Q8 format tablets use channel 0 of the PWM controller for backlight dimming. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-10-12ARM: dts: sun5i: Add PWM channel 0 pinmux setting for A13/A10sHans de Goede1-0/+7
Add a pinmux setting for the first pwm channel. This is often used for backlight dimming on tablets. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-10-12ARM: dts: sun5i: Add PWM controller node for A13 / A10sHans de Goede2-0/+18
Add dts nodes for the PWM controller on the A13 / A10s. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-10-12ARM: sun5i: Add C.H.I.P DTSMaxime Ripard2-1/+216
The C.H.I.P. is a small SBC with an Allwinner R8, 8GB of NAND, 512MB of RAM, USB host and OTG, a wifi / bluetooth combo chip, an audio/video jack and two connectors to plug additional boards on top of it. Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Chen-Yu Tsai <wens@csie.org>