| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch enables USB HS working in FS mode on stm32f429-disco
with 5V VBUS enable.
Signed-off-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
This patch enables USB FS on stm32f469-disco with 5V VBUS enable.
Signed-off-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
This patch adds the USB pins and nodes for USB FS core.
Signed-off-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
The Moxa ART GPIO is a Faraday FTGPIO010. Augment the DTS node
to indicate both compatible values for the SoC and the IP part.
Also increase the register range to 0x100, it has at least 0x48
bytes of registers, and a few extra will not hurt.
Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This moves the spi0_cs3_pin pinconf node from the LEGO EV3 file to the
common DA850 include file. This node is applicable to any board, and
therefore belongs in the common file.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
The two st231-rproc nodes have the same name; Due to that it was
impossible to distinguish them in remoteproc sysfs and debugfs
interface.
This patch provides them a name related to their functionality.
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
|
|
All three devices provide GPIO based LEDs named power,
wlan and app.
Place LEDs definition into a separate dtsi file as not all
devices including am335x-baltos.dtsi have the same LED layout.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
There's a typo, it should be GPIO176 and not GPIO106.
And it seems I messed up the regulators at some point while trying
to figure out what devices the regulators are used. The correct
regulator for MMC1 is vwlan2.
Fixes: 0d4cb3ccee58 ("ARM: dts: Configure regulators for droid 4")
Reported-by: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Tested-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The Cortina Gemini has an internal PCI root bus, add this to
the device tree, and add interrupt mapping (swizzling) to the
relevant systems device trees.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Feng-Hsin Chiang <john453@faraday-tech.com>
Cc: Greentime Hu <green.hu@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Currently the slope and offset values for calculating the
hot spot temperature of a particular thermal zone is part
of driver data. Pass them here instead and obtain the values
while of node parsing.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Currently the slope and offset values for calculating the
hot spot temperature of a particular thermal zone is part
of driver data. Pass them here instead and obtain the values
while of node parsing.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Currently the slope and offset values for calculating the
hot spot temperature of a particular thermal zone is part
of driver data. Pass them here instead and obtain the values
while of node parsing.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Currently the slope and offset values for calculating the
hot spot temperature of a particular thermal zone is part
of driver data. Pass them here instead and obtain the values
while of node parsing.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add cpu_thermal zone.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add basic support for STM32H743 MCU and his eval board.
The STMicrolectornics's STM32H743 MCU is based on Cortex-M7 core
running up to @400MHz with 2MB internal flash and 1MB internal RAM.
For more details see:
Documentation/arm/stm32/stm32h743-overview.txt
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
Add pinmux for rx,tx,cts and rts lines of uart0. This will enable uart0
to use hardware flow control.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Enable support for W25Q64CVSSIG which is a Winbond 64 Mbit SPI NOR.
At boot you will see the following message:
m25p80 spi1.0: found s25fl064k, expected w25q64
This is because the JEDEC ID for this chip is the same as s25fl064k.
However, this should be harmless since both chips are essentially the
same.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
W25Q64 is found on TI's AM335x ICEv2 board. Add it to list
for supported SPI flash devices. This flash can be identified
using JEDEC READ ID opcode.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
After the ti-cpufreq driver has been added, we can now drop the
operating-points table present in dra7.dtsi for the cpu and add an
operating-points-v2 table with all OPPs available for all silicon
revisions. Also add necessary data for use by ti-cpufreq to selectively
enable the appropriate OPPs at runtime as part of the operating-points
table.
As we now need to define voltage ranges for each OPP, we define the
minimum and maximum voltage to match the ranges possible for AVS class0
voltage as defined by the DRA7/AM57 Data Manual, with the exception of
using a range for OPP_OD based on historical data to ensure that SoCs
from older lots still continue to boot, even though more optimal voltages
are now the standard. Once an AVS Class0 driver is in place it will be
possible for these OPP voltages to be adjusted to any voltage within the
provided range.
Information from SPRS953, Revised December 2015.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
eviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The operatings-points-v2 table for am4372 was merged before any user of
it was present in the kernel and before the binding had been finalized.
The new ti-cpufreq driver and binding expects the platform specific
properties to be part of the operating-points-v2 table rather than the
cpu node so let's move them there as the only user is the ti-cpufreq
driver.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
eviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Although all PG2.0 silicon may not support 1GHz OPP for the MPU, older
Beaglebone Blacks may have PG2.0 silicon populated and these particular
parts are guaranteed to support the OPP, so enable it for PG2.0 on
am335x-boneblack only.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
eviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
After the ti-cpufreq driver has been added, we can now drop the
operating-points table present in am33xx.dtsi for the cpu and add an
operating-points-v2 table with all OPPs available for all silicon
revisions. Also add necessary data for use by ti-cpufreq to selectively
enable the appropriate OPPs at runtime as part of the operating-points
table.
Information from AM335x Data Manual, SPRS717i, Revised December 2015,
Table 5-7.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
eviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add the SATA controller node to the dm8168-evm device tree.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This board has an external oscillator supplying the reference clock
signal for SATA. Its rate is fixed at 100Mhz. Add a corresponding
device tree node.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Define and enable pwm1 and pwm3, timers1 & 3 trigger outputs on
on stm32f429i-eval board.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
Configure STM32F4 ADC to use dma by default.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
This patch enables RTC on stm32746g-eval with default LSE clock source.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
This patch adds STM32 RTC bindings for STM32F746.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
This patch set HSE_RTC clock frequency to 1 MHz, as the clock supplied to
the RTC must be 1 MHz.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
This patch lists STM32F7's RCC numeric constants.
It will be used by clock and reset drivers, and DT bindings.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
This patch enables clocks for STM32F746 MCU.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
Add appropriate properties to devices in the Linksys WRT AC Series for the
mvneta driver to use hardware buffer management.
Also update "soc" ranges property and set the status of bm and bm-bppi
to "okay" (SRAM).
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The Nokia N950 and N9 have a wl1271 (with nokia bootloader) bluetooth
module connected to second UART.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add bcm2048 node and its system clock to the N900 device tree file.
Apart from that a reference to the new clock has been added to
wl1251 (which uses it, too).
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The unit address for the msi controller is not valid as there is no reg
property, so remove it. Also, msi-controller is the preferred node name.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Jon Mason <jonmason@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
This adds baud rate, parity & number of data bits. It's required to get
serial working correctly.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
So far every Northstar device we have seen was using the same serial
console params (115200n8). It probably make the most sense to put it in
some proper dtsi files instead of repeating over and over for every
single device. As different boards may use different bootloaders it
seems the safest idea is to use board specific dtsi files.
Just in case some vendor decides to use different UART (parameters) this
can be always easily overwritten.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Droid 4 has two modems, mdm6600 and w3glte. Both are on the HCI USB
controller.
Let's add a configuration for the HCI so the modems can be enabled.
Note that the modems still need additional GPIO based configuration.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Tested-by: Sebastian Reichel <sre@kernel.org>
[tony@atomide.com: left out url]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add LEDs.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The LCD panel on droid 4 is a command mode LCD. The binding follows
the standard omapdrm binding and the changes needed for omapdrm command
mode panels are posted separately.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can get HDMI working as long as the 5V regulator is on. There is
probably an encoder chip there too, but so far no idea what it might be.
Let's keep the 5V HDMI regulator always enabled for now as otherwise we
cannot detect the monitor properly.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add tmp105 sensor for droid 4. This can be used with modprobe
lm75.ko and running sensors from lm-sensors package. Note that
the lm75.c driver does not yet support alert interrupt but
droid 4 seems to be wired for it.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Droid 4 has a GPIO line that we can use with CONFIG_POWER_RESET_GPIO.
It is probably connected to the CPCAP PMIC, and seems to power down
the whole device taking power consumption to zero based on what
I measured.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The TI LMU driver has not yet been merged, but the device
tree binding for TI LMU drivers has been acked already
earlier by Rob Herring <robh+dt@kernel.org>. So it should
be safe to apply to cut down the number of pending patches.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Acked-by: Milo Kim <milo.kim@ti.com>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This commit enable DMA-based transfers for SD/eMMC card adapters
and reduce number of interrupts produced by SD-card/eMMC-card
adapters.
Sometimes interrupts from SD-card/eMMC-card adapters running in
PIO mode blocks execution of hrtimers and I2S DMA callbacks for
a long periods (100 ms or more).
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
[moved dma properties to rk3xxx.dtsi and added sdio dma]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The binding should state "cortina,gemini-gpio", "faraday,ftgpio010"
stating the full name of the IP part.
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
According to [0] pointed out by Marc Zyngier in a report about a
similar error message, PPIs 11 and 13 are edge triggered on
Cortex-A9 socs including the rk3066 and rk3188 which currently
mark them as level triggered.
Until some time ago the gic did not care but commit 992345a58e0c
("irqchip/gic: WARN if setting the interrupt type for a PPI fails")
introduced a warning for that case.
Fix the warning on these socs by describing the interrupts correctly
and also using the binding constants for easier reading in the future.
[0] http://infocenter.arm.com/help/topic/com.arm.doc.ddi0407f/CCHEIGIC.html
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The moxart interrupt line flags were not respected in previous
driver: instead of assigning them per-consumer, a fixes mask
was set in the controller.
With the migration to a standard Faraday driver we need to
set up and handle the consumer flags correctly. Also remove
the Moxart-specific flags when switching to using real consumer
flags.
Extend the register window to 0x100 bytes as we may have a few
more registers in there and it doesn't hurt.
Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Allow including of dtsi files in an architecture-independent manner.
Some dtsi files may be shared between architectures and one suggestion
was to have symlinks and let these includes get accessed via a
#include <arm64/foo.dtsi>
So add the necessary symlinks for arm32.
Suggested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Allow including of dtsi files in an architecture-independent manner.
Some dtsi files may be shared between architectures and one suggestion
was to have symlinks and let these includes get accessed via a
#include <arm64/foo.dtsi>
So add the necessary symlinks for arm32.
Suggested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
Bruno Herrera
Linus Walleij
David Lechner
Loic Pallardy
Yegor Yefremov
Tony Lindgren
Keerthy
Alexandre TORGUE
Vignesh R
Franklin S Cooper Jr
Sekhar Nori
Dave Gerlach
Bartosz Golaszewski
Fabrice Gasnier
Amelie Delaunay
Gabriel Fernandez
Ralph Sennhauser
Sebastian Reichel
Rob Herring
Rafał Miłecki
Alexander Kochetkov
Heiko Stuebner