| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Currently the framebuffer content is displayed with incorrect offsets
in both the vertical and horizontal directions.
The fbdev version of the driver does not show this problem. Breno Lima
dumped the eLCDIF controller registers on both the drm and fbdev drivers
and noticed that the VDCTRL3 register is configured incorrectly in the
drm driver.
The fbdev driver calculates the vertical and horizontal wait counts
of the VDCTRL3 register by doing: back porch + sync length.
Looking at the horizontal and vertical timing diagram from
include/drm/drm_modes.h this value corresponds to:
crtc_[hv]total - crtc_[hv]sync_start
So fix the VDCTRL3 register setting accordingly so that the eLCDIF
controller can properly show the framebuffer content in the correct
position.
Reported-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The mxsfb driver will crash if the mxsfb DT node has a subnode,
but the content of the subnode is not of-graph binding with an
endpoint linking to panel. The crash was triggered by providing
old-style panel bindings to the mxsfb driver instead of the new
of-graph ones.
The problem happens in mxsfb_create_output(), which is invoked
from mxsfb_load(). The mxsfb_create_output() iterates over all
mxsfb DT subnode endpoints and tries to bind a panel on each
endpoint. If there is any problem binding the panel, that is,
mxsfb->panel == NULL, this function will return an error code,
otherwise success 0 is returned.
If the subnodes do not specify of-graph binding with an endpoint,
the iteration over endpoints in mxsfb_create_output() will have
zero cycles and the function will immediatelly return 0, but the
mxsfb->panel will remain NULL. This is propagated back into the
mxsfb_load(), which does not detect any problem and expects that
the mxsfb->panel is valid, thus calls mxsfb_panel_attach(). But
since mxsfb->panel == NULL, mxsfb_panel_attach() is called with
first argument NULL and this crashes the kernel.
This patch fixes the problem by explicitly checking for valid
mxsfb->panel at the end of the iteration in mxsfb_create_output().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The DRM subsystem specifies the pixel clock polarity from a
controllers perspective: DRM_BUS_FLAG_PIXDATA_NEGEDGE means
the controller drives the data on pixel clocks falling edge.
That is the controllers DOTCLK_POL=0 (Default is data launched
at negative edge).
Also change the data enable logic to be high active by default
and only change if explicitly requested via bus_flags. With
that defaults are:
- Data enable: high active
- Pixel clock polarity: controller drives data on negative edge
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The LCD bus width does not need to align with the pixel format. The
LCDIF controller automatically converts between pixel formats and
bus width by padding or dropping LSBs.
The DRM subsystem has the notion of bus_format which allows to
determine what bus_formats are supported by the display. Choose the
first available or fallback to 24 bit if none are available.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
It's a void function, so there is no return value;
Link: http://lkml.kernel.org/r/20170309150817.7510-1-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Recently fallocate patch was merged and it uses
MSDOS_I(inode)->mmu_private at fat_evict_inode(). However,
fat_inode/fsinfo_inode that was introduced in past didn't initialize
MSDOS_I(inode) properly.
With those combinations, it became the cause of accessing random entry
in FAT area.
Link: http://lkml.kernel.org/r/87pohrj4i8.fsf@mail.parknet.co.jp
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Reported-by: Moreno Bartalucci <moreno.bartalucci@tecnorama.it>
Tested-by: Moreno Bartalucci <moreno.bartalucci@tecnorama.it>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove incorrect CONFIG_IDE ifdef (CONFIG_IDE config option is for
internal drivers/ide/ use) and make IDE hardware interface always
initialized (not only when IDE subsystem is built-in).
This patch allows Cayman board to work with modular IDE subsystem
support and removes the requirement of having the whole core IDE
subsystem built-in when using libata PATA support.
Link: http://lkml.kernel.org/r/1990884.yFoE6lSB9G@amdc3058
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
quarantine_remove_cache() frees all pending objects that belong to the
cache, before we destroy the cache itself. However there are currently
two possibilities how it can fail to do so.
First, another thread can hold some of the objects from the cache in
temp list in quarantine_put(). quarantine_put() has a windows of
enabled interrupts, and on_each_cpu() in quarantine_remove_cache() can
finish right in that window. These objects will be later freed into the
destroyed cache.
Then, quarantine_reduce() has the same problem. It grabs a batch of
objects from the global quarantine, then unlocks quarantine_lock and
then frees the batch. quarantine_remove_cache() can finish while some
objects from the cache are still in the local to_free list in
quarantine_reduce().
Fix the race with quarantine_put() by disabling interrupts for the whole
duration of quarantine_put(). In combination with on_each_cpu() in
quarantine_remove_cache() it ensures that quarantine_remove_cache()
either sees the objects in the per-cpu list or in the global list.
Fix the race with quarantine_reduce() by protecting quarantine_reduce()
with srcu critical section and then doing synchronize_srcu() at the end
of quarantine_remove_cache().
I've done some assessment of how good synchronize_srcu() works in this
case. And on a 4 CPU VM I see that it blocks waiting for pending read
critical sections in about 2-3% of cases. Which looks good to me.
I suspect that these races are the root cause of some GPFs that I
episodically hit. Previously I did not have any explanation for them.
BUG: unable to handle kernel NULL pointer dereference at 00000000000000c8
IP: qlist_free_all+0x2e/0xc0 mm/kasan/quarantine.c:155
PGD 6aeea067
PUD 60ed7067
PMD 0
Oops: 0000 [#1] SMP KASAN
Dumping ftrace buffer:
(ftrace buffer empty)
Modules linked in:
CPU: 0 PID: 13667 Comm: syz-executor2 Not tainted 4.10.0+ #60
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
task: ffff88005f948040 task.stack: ffff880069818000
RIP: 0010:qlist_free_all+0x2e/0xc0 mm/kasan/quarantine.c:155
RSP: 0018:ffff88006981f298 EFLAGS: 00010246
RAX: ffffea0000ffff00 RBX: 0000000000000000 RCX: ffffea0000ffff1f
RDX: 0000000000000000 RSI: ffff88003fffc3e0 RDI: 0000000000000000
RBP: ffff88006981f2c0 R08: ffff88002fed7bd8 R09: 00000001001f000d
R10: 00000000001f000d R11: ffff88006981f000 R12: ffff88003fffc3e0
R13: ffff88006981f2d0 R14: ffffffff81877fae R15: 0000000080000000
FS: 00007fb911a2d700(0000) GS:ffff88003ec00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000000000c8 CR3: 0000000060ed6000 CR4: 00000000000006f0
Call Trace:
quarantine_reduce+0x10e/0x120 mm/kasan/quarantine.c:239
kasan_kmalloc+0xca/0xe0 mm/kasan/kasan.c:590
kasan_slab_alloc+0x12/0x20 mm/kasan/kasan.c:544
slab_post_alloc_hook mm/slab.h:456 [inline]
slab_alloc_node mm/slub.c:2718 [inline]
kmem_cache_alloc_node+0x1d3/0x280 mm/slub.c:2754
__alloc_skb+0x10f/0x770 net/core/skbuff.c:219
alloc_skb include/linux/skbuff.h:932 [inline]
_sctp_make_chunk+0x3b/0x260 net/sctp/sm_make_chunk.c:1388
sctp_make_data net/sctp/sm_make_chunk.c:1420 [inline]
sctp_make_datafrag_empty+0x208/0x360 net/sctp/sm_make_chunk.c:746
sctp_datamsg_from_user+0x7e8/0x11d0 net/sctp/chunk.c:266
sctp_sendmsg+0x2611/0x3970 net/sctp/socket.c:1962
inet_sendmsg+0x164/0x5b0 net/ipv4/af_inet.c:761
sock_sendmsg_nosec net/socket.c:633 [inline]
sock_sendmsg+0xca/0x110 net/socket.c:643
SYSC_sendto+0x660/0x810 net/socket.c:1685
SyS_sendto+0x40/0x50 net/socket.c:1653
I am not sure about backporting. The bug is quite hard to trigger, I've
seen it few times during our massive continuous testing (however, it
could be cause of some other episodic stray crashes as it leads to
memory corruption...). If it is triggered, the consequences are very
bad -- almost definite bad memory corruption. The fix is non trivial
and has chances of introducing new bugs. I am also not sure how
actively people use KASAN on older releases.
[dvyukov@google.com: - sorted includes[
Link: http://lkml.kernel.org/r/20170309094028.51088-1-dvyukov@google.com
Link: http://lkml.kernel.org/r/20170308151532.5070-1-dvyukov@google.com
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Greg Thelen <gthelen@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We see reported stalls/lockups in quarantine_remove_cache() on machines
with large amounts of RAM. quarantine_remove_cache() needs to scan
whole quarantine in order to take out all objects belonging to the
cache. Quarantine is currently 1/32-th of RAM, e.g. on a machine with
256GB of memory that will be 8GB. Moreover quarantine scanning is a
walk over uncached linked list, which is slow.
Add cond_resched() after scanning of each non-empty batch of objects.
Batches are specifically kept of reasonable size for quarantine_put().
On a machine with 256GB of RAM we should have ~512 non-empty batches,
each with 16MB of objects.
Link: http://lkml.kernel.org/r/20170308154239.25440-1-dvyukov@google.com
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Greg Thelen <gthelen@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
mem_cgroup_free() indirectly calls wb_domain_exit() which is not
prepared to deal with a struct wb_domain object that hasn't executed
wb_domain_init(). For instance, the following warning message is
printed by lockdep if alloc_percpu() fails in mem_cgroup_alloc():
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 1 PID: 1950 Comm: mkdir Not tainted 4.10.0+ #151
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
dump_stack+0x67/0x99
register_lock_class+0x36d/0x540
__lock_acquire+0x7f/0x1a30
lock_acquire+0xcc/0x200
del_timer_sync+0x3c/0xc0
wb_domain_exit+0x14/0x20
mem_cgroup_free+0x14/0x40
mem_cgroup_css_alloc+0x3f9/0x620
cgroup_apply_control_enable+0x190/0x390
cgroup_mkdir+0x290/0x3d0
kernfs_iop_mkdir+0x58/0x80
vfs_mkdir+0x10e/0x1a0
SyS_mkdirat+0xa8/0xd0
SyS_mkdir+0x14/0x20
entry_SYSCALL_64_fastpath+0x18/0xad
Add __mem_cgroup_free() which skips wb_domain_exit(). This is used by
both mem_cgroup_free() and mem_cgroup_alloc() clean up.
Fixes: 0b8f73e104285 ("mm: memcontrol: clean up alloc, online, offline, free functions")
Link: http://lkml.kernel.org/r/20170306192122.24262-1-tahsin@google.com
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The following test case triggers BUG() in munlock_vma_pages_range():
int main(int argc, char *argv[])
{
int fd;
system("mount -t tmpfs -o huge=always none /mnt");
fd = open("/mnt/test", O_CREAT | O_RDWR);
ftruncate(fd, 4UL << 20);
mmap(NULL, 4UL << 20, PROT_READ | PROT_WRITE,
MAP_SHARED | MAP_FIXED | MAP_LOCKED, fd, 0);
mmap(NULL, 4096, PROT_READ | PROT_WRITE,
MAP_SHARED | MAP_LOCKED, fd, 0);
munlockall();
return 0;
}
The second mmap() create PTE-mapping of the first huge page in file. It
makes kernel munlock the page as we never keep PTE-mapped page mlocked.
On munlockall() when we handle vma created by the first mmap(),
munlock_vma_page() returns page_mask == 0, as the page is not mlocked
anymore. On next iteration follow_page_mask() return tail page, but
page_mask is HPAGE_NR_PAGES - 1. It makes us skip to the first tail
page of the next huge page and step on
VM_BUG_ON_PAGE(PageMlocked(page)).
The fix is not use the page_mask from follow_page_mask() at all. It has
no use for us.
Link: http://lkml.kernel.org/r/20170302150252.34120-1-kirill.shutemov@linux.intel.com
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: <stable@vger.kernel.org> [4.5+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The following test case triggers NULL-pointer derefernce in
try_to_unmap_one():
#include <fcntl.h>
#include <stdlib.h>
#include <unistd.h>
#include <sys/mman.h>
int main(int argc, char *argv[])
{
int fd;
system("mount -t tmpfs -o huge=always none /mnt");
fd = open("/mnt/test", O_CREAT | O_RDWR);
ftruncate(fd, 2UL << 20);
mmap(NULL, 2UL << 20, PROT_READ | PROT_WRITE,
MAP_SHARED | MAP_FIXED | MAP_LOCKED, fd, 0);
mmap(NULL, 2UL << 20, PROT_READ | PROT_WRITE,
MAP_SHARED | MAP_LOCKED, fd, 0);
munlockall();
return 0;
}
Apparently, there's a case when we call try_to_unmap() on huge PMDs:
it's TTU_MUNLOCK.
Let's handle this case correctly.
Fixes: c7ab0d2fdc84 ("mm: convert try_to_unmap_one() to use page_vma_mapped_walk()")
Link: http://lkml.kernel.org/r/20170302151159.30592-1-kirill.shutemov@linux.intel.com
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Obviously, we should not access memblock.memory.regions[right] if
'right' is outside of [0..memblock.memory.cnt>.
Fixes: b92df1de5d28 ("mm: page_alloc: skip over regions of invalid pfns where possible")
Link: http://lkml.kernel.org/r/20170303023745.9104-1-takahiro.akashi@linaro.org
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
linux/tools/testing/selftests/vm $ make
gcc -Wall -I ../../../../usr/include compaction_test.c -lrt -o /compaction_test
/usr/lib/gcc/x86_64-pc-linux-gnu/4.9.4/../../../../x86_64-pc-linux-gnu/bin/ld: cannot open output file /compaction_test: Permission denied
collect2: error: ld returned 1 exit status
make: *** [../lib.mk:54: /compaction_test] Error 1
Since commit a8ba798bc8ec ("selftests: enable O and KBUILD_OUTPUT")
selftests/vm build fails if run from the "selftests/vm" directory, but
it works in the selftests/ directory. It's quicker to be able to do a
local vm-only build after a tree wipe and this patch allows for it
again.
Link: http://lkml.kernel.org/r/20170302173738.18994-4-aarcange@redhat.com
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
userfaultfd_remove() has to be execute before zapping the pagetables or
UFFDIO_COPY could keep filling pages after zap_page_range returned,
which would result in non zero data after a MADV_DONTNEED.
However userfaultfd_remove() may have to release the mmap_sem. This was
handled correctly in MADV_REMOVE, but MADV_DONTNEED accessed a
potentially stale vma (the very vma passed to zap_page_range(vma, ...)).
The fix consists in revalidating the vma in case userfaultfd_remove()
had to release the mmap_sem.
This also optimizes away an unnecessary down_read/up_read in the
MADV_REMOVE case if UFFD_EVENT_FORK had to be delivered.
It all remains zero runtime cost in case CONFIG_USERFAULTFD=n as
userfaultfd_remove() will be defined as "true" at build time.
Link: http://lkml.kernel.org/r/20170302173738.18994-3-aarcange@redhat.com
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Acked-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We have a memleak in the ->new ctx if the uffd of the parent is closed
before the fork event is read, nothing frees the new context.
Link: http://lkml.kernel.org/r/20170302173738.18994-2-aarcange@redhat.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reported-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The system may panic when initialisation is done when almost all the
memory is assigned to the huge pages using the kernel command line
parameter hugepage=xxxx. Panic may occur like this:
Unable to handle kernel paging request for data at address 0x00000000
Faulting instruction address: 0xc000000000302b88
Oops: Kernel access of bad area, sig: 11 [#1]
SMP NR_CPUS=2048 [ 0.082424] NUMA
pSeries
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.9.0-15-generic #16-Ubuntu
task: c00000021ed01600 task.stack: c00000010d108000
NIP: c000000000302b88 LR: c000000000270e04 CTR: c00000000016cfd0
REGS: c00000010d10b2c0 TRAP: 0300 Not tainted (4.9.0-15-generic)
MSR: 8000000002009033 <SF,VEC,EE,ME,IR,DR,RI,LE>[ 0.082770] CR: 28424422 XER: 00000000
CFAR: c0000000003d28b8 DAR: 0000000000000000 DSISR: 40000000 SOFTE: 1
GPR00: c000000000270e04 c00000010d10b540 c00000000141a300 c00000010fff6300
GPR04: 0000000000000000 00000000026012c0 c00000010d10b630 0000000487ab0000
GPR08: 000000010ee90000 c000000001454fd8 0000000000000000 0000000000000000
GPR12: 0000000000004400 c00000000fb80000 00000000026012c0 00000000026012c0
GPR16: 00000000026012c0 0000000000000000 0000000000000000 0000000000000002
GPR20: 000000000000000c 0000000000000000 0000000000000000 00000000024200c0
GPR24: c0000000016eef48 0000000000000000 c00000010fff7d00 00000000026012c0
GPR28: 0000000000000000 c00000010fff7d00 c00000010fff6300 c00000010d10b6d0
NIP mem_cgroup_soft_limit_reclaim+0xf8/0x4f0
LR do_try_to_free_pages+0x1b4/0x450
Call Trace:
do_try_to_free_pages+0x1b4/0x450
try_to_free_pages+0xf8/0x270
__alloc_pages_nodemask+0x7a8/0xff0
new_slab+0x104/0x8e0
___slab_alloc+0x620/0x700
__slab_alloc+0x34/0x60
kmem_cache_alloc_node_trace+0xdc/0x310
mem_cgroup_init+0x158/0x1c8
do_one_initcall+0x68/0x1d0
kernel_init_freeable+0x278/0x360
kernel_init+0x24/0x170
ret_from_kernel_thread+0x5c/0x74
Instruction dump:
eb81ffe0 eba1ffe8 ebc1fff0 ebe1fff8 4e800020 3d230001 e9499a42 3d220004
3929acd8 794a1f24 7d295214 eac90100 <e9360000> 2fa90000 419eff74 3b200000
---[ end trace 342f5208b00d01b6 ]---
This is a chicken and egg issue where the kernel try to get free memory
when allocating per node data in mem_cgroup_init(), but in that path
mem_cgroup_soft_limit_reclaim() is called which assumes that these data
are allocated.
As mem_cgroup_soft_limit_reclaim() is best effort, it should return when
these data are not yet allocated.
This patch also fixes potential null pointer access in
mem_cgroup_remove_from_trees() and mem_cgroup_update_tree().
Link: http://lkml.kernel.org/r/1487856999-16581-2-git-send-email-ldufour@linux.vnet.ibm.com
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Link: http://lkml.kernel.org/r/20170226060230.11555-1-standby24x7@gmail.com
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Coly Li <colyli@suse.de>
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We added support for PUD-sized transparent hugepages, however we count
the event "thp split pud" into thp_split_pmd event.
To separate the event count of thp split pud from pmd, add a new event
named thp_split_pud.
Link: http://lkml.kernel.org/r/1488282380-5076-1-git-send-email-xieyisheng1@huawei.com
Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Ebru Akagunduz <ebru.akagunduz@gmail.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
With arm-linux-gcc-4.2, almost every file we build in the kernel ends up
with this warning:
include/linux/fs.h:2648: warning: comparison of unsigned expression < 0 is always false
Later versions don't have this problem, but it's easy enough to work
around.
Link: http://lkml.kernel.org/r/20161216105634.235457-12-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Don't stop running dup_fctx() even if userfaultfd_event_wait_completion
fails as it has to run userfaultfd_ctx_put on all ctx to pair against
the userfaultfd_ctx_get that was run on all fctx->orig in
dup_userfaultfd.
Link: http://lkml.kernel.org/r/20170224181957.19736-4-aarcange@redhat.com
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Acked-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Similar to the handle_userfault() case, also make sure to never attempt
to send any event past the PF_EXITING point of no return.
This is purely a robustness check.
Link: http://lkml.kernel.org/r/20170224181957.19736-3-aarcange@redhat.com
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Acked-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Patch series "userfaultfd non-cooperative further update for 4.11 merge
window".
Unfortunately I noticed one relevant bug in userfaultfd_exit while doing
more testing. I've been doing testing before and this was also tested
by kbuild bot and exercised by the selftest, but this bug never
reproduced before.
I dropped userfaultfd_exit as result. I dropped it because of
implementation difficulty in receiving signals in __mmput and because I
think -ENOSPC as result from the background UFFDIO_COPY should be enough
already.
Before I decided to remove userfaultfd_exit, I noticed userfaultfd_exit
wasn't exercised by the selftest and when I tried to exercise it, after
moving it to a more correct place in __mmput where it would make more
sense and where the vma list is stable, it resulted in the
event_wait_completion in D state. So then I added the second patch to
be sure even if we call userfaultfd_event_wait_completion too late
during task exit(), we won't risk to generate tasks in D state. The
same check exists in handle_userfault() for the same reason, except it
makes a difference there, while here is just a robustness check and it's
run under WARN_ON_ONCE.
While looking at the userfaultfd_event_wait_completion() function I
looked back at its callers too while at it and I think it's not ok to
stop executing dup_fctx on the fcs list because we relay on
userfaultfd_event_wait_completion to execute
userfaultfd_ctx_put(fctx->orig) which is paired against
userfaultfd_ctx_get(fctx->orig) in dup_userfault just before
list_add(fcs). This change only takes care of fctx->orig but this area
also needs further review looking for similar problems in fctx->new.
The only patch that is urgent is the first because it's an use after
free during a SMP race condition that affects all processes if
CONFIG_USERFAULTFD=y. Very hard to reproduce though and probably
impossible without SLUB poisoning enabled.
This patch (of 3):
I once reproduced this oops with the userfaultfd selftest, it's not
easily reproducible and it requires SLUB poisoning to reproduce.
general protection fault: 0000 [#1] SMP
Modules linked in:
CPU: 2 PID: 18421 Comm: userfaultfd Tainted: G ------------ T 3.10.0+ #15
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.10.1-0-g8891697-prebuilt.qemu-project.org 04/01/2014
task: ffff8801f83b9440 ti: ffff8801f833c000 task.ti: ffff8801f833c000
RIP: 0010:[<ffffffff81451299>] [<ffffffff81451299>] userfaultfd_exit+0x29/0xa0
RSP: 0018:ffff8801f833fe80 EFLAGS: 00010202
RAX: ffff8801f833ffd8 RBX: 6b6b6b6b6b6b6b6b RCX: ffff8801f83b9440
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff8800baf18600
RBP: ffff8801f833fee8 R08: 0000000000000000 R09: 0000000000000001
R10: 0000000000000000 R11: ffffffff8127ceb3 R12: 0000000000000000
R13: ffff8800baf186b0 R14: ffff8801f83b99f8 R15: 00007faed746c700
FS: 0000000000000000(0000) GS:ffff88023fc80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 00007faf0966f028 CR3: 0000000001bc6000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Call Trace:
do_exit+0x297/0xd10
SyS_exit+0x17/0x20
tracesys+0xdd/0xe2
Code: 00 00 66 66 66 66 90 55 48 89 e5 41 54 53 48 83 ec 58 48 8b 1f 48 85 db 75 11 eb 73 66 0f 1f 44 00 00 48 8b 5b 10 48 85 db 74 64 <4c> 8b a3 b8 00 00 00 4d 85 e4 74 eb 41 f6 84 24 2c 01 00 00 80
RIP [<ffffffff81451299>] userfaultfd_exit+0x29/0xa0
RSP <ffff8801f833fe80>
---[ end trace 9fecd6dcb442846a ]---
In the debugger I located the "mm" pointer in the stack and walking
mm->mmap->vm_next through the end shows the vma->vm_next list is fully
consistent and it is null terminated list as expected. So this has to
be an SMP race condition where userfaultfd_exit was running while the
vma list was being modified by another CPU.
When userfaultfd_exit() run one of the ->vm_next pointers pointed to
SLAB_POISON (RBX is the vma pointer and is 0x6b6b..).
The reason is that it's not running in __mmput but while there are still
other threads running and it's not holding the mmap_sem (it can't as it
has to wait the even to be received by the manager). So this is an use
after free that was happening for all processes.
One more implementation problem aside from the race condition:
userfaultfd_exit has really to check a flag in mm->flags before walking
the vma or it's going to slowdown the exit() path for regular tasks.
One more implementation problem: at that point signals can't be
delivered so it would also create a task in D state if the manager
doesn't read the event.
The major design issue: it overall looks superfluous as the manager can
check for -ENOSPC in the background transfer:
if (mmget_not_zero(ctx->mm)) {
[..]
} else {
return -ENOSPC;
}
It's safer to roll it back and re-introduce it later if at all.
[rppt@linux.vnet.ibm.com: documentation fixup after removal of UFFD_EVENT_EXIT]
Link: http://lkml.kernel.org/r/1488345437-4364-1-git-send-email-rppt@linux.vnet.ibm.com
Link: http://lkml.kernel.org/r/20170224181957.19736-2-aarcange@redhat.com
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Acked-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
All exit paths from gup_pte_range() require pte_unmap() of the original
pte page before returning. Refactor the code to have a single exit
point to do the unmap.
This mirrors the flow of the generic gup_pte_range() in mm/gup.c.
Link: http://lkml.kernel.org/r/148804251828.36605.14910389618497006945.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
gup_pte_range() fails to check pte_allows_gup() before translating a DAX
pte entry, pte_devmap(), to a page. This allows writes to read-only
mappings, and bypasses the DAX cacheline dirty tracking due to missed
'mkwrite' faults. The gup_huge_pmd() path and the gup_huge_pud() path
correctly check pte_allows_gup() before checking for _devmap() entries.
Fixes: 3565fce3a659 ("mm, x86: get_user_pages() for dax mappings")
Link: http://lkml.kernel.org/r/148804251312.36605.12665024794196605053.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reported-by: Dave Hansen <dave.hansen@linux.intel.com>
Reported-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Xiong Zhou <xzhou@redhat.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We use pte_write() to check whethwer the pte entry is writable. This is
mostly used to later mark the pte read only if it is writable. The other
use of pte_write() is to check whether the pte_entry is writable so that
hardware page table entry can be marked accordingly. This is used in kvm
where we look at qemu page table entry and update hardware hash page table
for the guest with correct write enable bit.
With the above, for the first usage we should also check the savedwrite
bit so that we can correctly clear the savedwite bit. For the later, we
add a new variant __pte_write().
With this we can revert write_protect_page part of 595cd8f256d2 ("mm/ksm:
handle protnone saved writes when making page write protect"). But I left
it as it is as an example code for savedwrite check.
Fixes: c137a2757b886 ("powerpc/mm/autonuma: switch ppc64 to its own implementation of saved write")
Link: http://lkml.kernel.org/r/1488203787-17849-2-git-send-email-aneesh.kumar@linux.vnet.ibm.com
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Paul Mackerras <paulus@ozlabs.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We need to mark pages of parent process read only on fork. Numa fault
pte needs a protnone ptes variant with saved write flag set. On fork we
need to make sure we remove the saved write bit. Instead of adding the
protnone check in the caller update ptep_set_wrprotect variants to clear
savedwrite bit.
Without this we see random segfaults in application on fork.
Fixes: c137a2757b886 ("powerpc/mm/autonuma: switch ppc64 to its own implementation of saved write")
Link: http://lkml.kernel.org/r/1488203787-17849-1-git-send-email-aneesh.kumar@linux.vnet.ibm.com
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Paul Mackerras <paulus@ozlabs.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix typos and add the following to the scripts/spelling.txt:
overide||override
While we are here, fix the doubled "address" in the touched line
Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt.
Also, fix the comment block style in the touched hunks in
drivers/media/dvb-frontends/drx39xyj/drx_driver.h.
Link: http://lkml.kernel.org/r/1481573103-11329-21-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix typos and add the following to the scripts/spelling.txt:
disble||disable
disbled||disabled
I kept the TSL2563_INT_DISBLED in /drivers/iio/light/tsl2563.c
untouched. The macro is not referenced at all, but this commit is
touching only comment blocks just in case.
Link: http://lkml.kernel.org/r/1481573103-11329-20-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
__do_fault assumes vmf->page has been initialized and is valid if
VM_FAULT_NOPAGE is not returned by vma->vm_ops->fault(vma, vmf).
handle_userfault() in turn should return VM_FAULT_NOPAGE if it doesn't
return VM_FAULT_SIGBUS or VM_FAULT_RETRY (the other two possibilities).
This VM_FAULT_NOPAGE case is only invoked when signal are pending and it
didn't matter for anonymous memory before. It only started to matter
since shmem was introduced. hugetlbfs also takes a different path and
doesn't exercise __do_fault.
Link: http://lkml.kernel.org/r/20170228154201.GH5816@redhat.com
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We added new gem ioctl flags and the new fences ioctl, but forgot
to bump the version.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Reject it if there are any invalid flags or domains.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
For full 5-level paging we need a helper to allocate p4d page table.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Convert all non-architecture-specific code to 5-level paging.
It's mostly mechanical adding handling one more page table level in
places where we deal with pud_t.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Like with pgtable-nopud.h for 4-level paging, this new header is base
for converting an architectures to properly folded p4d_t level.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If an architecture uses 4level-fixup.h we don't need to do anything as
it includes 5level-fixup.h.
If an architecture uses pgtable-nop*d.h, define __ARCH_USE_5LEVEL_HACK
before inclusion of the header. It makes asm-generic code to use
5level-fixup.h.
If an architecture has 4-level paging or folds levels on its own,
include 5level-fixup.h directly.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We are going to introduce <asm-generic/pgtable-nop4d.h> to provide
abstraction for properly (in opposite to 5level-fixup.h hack) folded
p4d level. The new header will be included from pgtable-nopud.h.
If an architecture uses <asm-generic/nop*d.h>, we cannot use
5level-fixup.h directly to quickly convert the architecture to 5-level
paging as it would conflict with pgtable-nop4d.h.
With this patch an architecture can define __ARCH_USE_5LEVEL_HACK before
inclusion <asm-genenric/nop*d.h> to use 5level-fixup.h.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We are going to switch core MM to 5-level paging abstraction.
This is preparation step which adds <asm-generic/5level-fixup.h>
As with 4level-fixup.h, the new header allows quickly make all
architectures compatible with 5-level paging in core MM.
In long run we would like to switch architectures to properly folded p4d
level by using <asm-generic/pgtable-nop4d.h>, but it requires more
changes to arch-specific code.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Look for 'la57' in /proc/cpuinfo to see if your machine supports 5-level
paging.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This reverts commit b0c1e95ab44feaad8831f2c06a3473c974003b49. It
contains a flaw and the next version has more features added which makes
me want to move it to the next cycle.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This reverts commit 02dbfa5e5583523035f05636c614a0eca77f1aab. I grabbed
the wrong version from the list and will pull the proper one from Peter
Rosin's mux tree.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
After commit 7999eecb7e56 ("i2c: exynos5: fix arbitration lost handling"),
some I2C transactions are failing because the TRANSFER_DONE_AUTO field is
not set in the I2C_TRANS_STATUS register so the i2c->status value is left
to -EINVAL causing the i2c->msg_complete completion to never be signaled.
For example, when reading the time of an I2C rtc on an Exynos5800 machine:
$ cat /sys/class/rtc/rtc0/time
[ 25.924594] exynos5-hsi2c 12e10000.i2c: rx timeout
[ 65.028365] max77686-rtc max77802-rtc: Fail to read time reg(-22)
cat: /sys/class/rtc/rtc0/time: Invalid argument
The Exynos5422 manual states clearly that most I2C_TRANS_STATUS reg bits
(including TRANSFER_DONE_AUTO) are cleared after the register is read. So
reading has side effects and should only be done if HSI2C_INT_I2C was set.
Fixes: 7999eecb7e56 ("i2c: exynos5: fix arbitration lost handling")
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Signed-off-by: Jim Qu <Jim.Qu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Commit 13ad59df67f1 ("mm, page_alloc: avoid page_to_pfn() when merging
buddies") moved the check for memory holes out of page_is_buddy() and
had the callers do the check.
But this wasn't done correctly in one place which caused ia64 to crash
very early in boot.
Update to fix that and make ia64 boot again.
[ v2: Vlastimil pointed out we don't need to call page_to_pfn()
since we already have the result of that in "buddy_pfn" ]
Fixes: 13ad59df67f1 ("avoid page_to_pfn() when merging buddies")
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This removes the extra include header file that was added in commit
e58bc927835a "Pull overlayfs updates from Miklos Szeredi" now that it
is no longer needed.
There are probably other such includes that got added during the
scheduler header splitup series, but this is the one that annoyed me
personally and I know about.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When a reflink operation causes the bmap code to allocate a btree block
we're currently doing single-AG allocations due to having ->firstblock
set and then try any higher AG due a little reflink quirk we've put in
when adding the reflink code. But given that we do not have a minleft
reservation of any kind in this AG we can still not have any space in
the same or higher AG even if the file system has enough free space.
To fix this use a XFS_ALLOCTYPE_FIRST_AG allocation in this fall back
path instead.
[And yes, we need to redo this properly instead of piling hacks over
hacks. I'm working on that, but it's not going to be a small series.
In the meantime this fixes the customer reported issue]
Also add a warning for failing allocations to make it easier to debug.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
|
|
The scheduler header file split and cleanups ended up exposing a few
nasty header file dependencies, and in particular it showed how we in
<linux/wait.h> ended up depending on "signal_pending()", which now comes
from <linux/sched/signal.h>.
That's a very subtle and annoying dependency, which already caused a
semantic merge conflict (see commit e58bc927835a "Pull overlayfs updates
from Miklos Szeredi", which added that fixup in the merge commit).
It turns out that we can avoid this dependency _and_ improve code
generation by moving the guts of the fairly nasty helper #define
__wait_event_interruptible_locked() to out-of-line code. The code that
includes the signal_pending() check is all in the slow-path where we
actually go to sleep waiting for the event anyway, so using a helper
function is the right thing to do.
Using a helper function is also what we already did for the non-locked
versions, see the "__wait_event*()" macros and the "prepare_to_wait*()"
set of helper functions.
We might want to try to unify all these macro games, we have a _lot_ of
subtly different wait-event loops. But this is the minimal patch to fix
the annoying header dependency.
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit fa7f138 ("xfs: clear delalloc and cache on buffered write
failure") fixed one regression in the iomap error handling code and
exposed another. The fundamental problem is that if a buffered write
is a rewrite of preexisting delalloc blocks and the write fails, the
failure handling code can punch out preexisting blocks with valid
file data.
This was reproduced directly by sub-block writes in the LTP
kernel/syscalls/write/write03 test. A first 100 byte write allocates
a single block in a file. A subsequent 100 byte write fails and
punches out the block, including the data successfully written by
the previous write.
To address this problem, update the ->iomap_begin() handler to
distinguish newly allocated delalloc blocks from preexisting
delalloc blocks via the IOMAP_F_NEW flag. Use this flag in the
->iomap_end() handler to decide when a failed or short write should
punch out delalloc blocks.
This introduces the subtle requirement that ->iomap_begin() should
never combine newly allocated delalloc blocks with existing blocks
in the resulting iomap descriptor. This can occur when a new
delalloc reservation merges with a neighboring extent that is part
of the current write, for example. Therefore, drop the
post-allocation extent lookup from xfs_bmapi_reserve_delalloc() and
just return the record inserted into the fork. This ensures only new
blocks are returned and thus that preexisting delalloc blocks are
always handled as "found" blocks and not punched out on a failed
rewrite.
Reported-by: Xiong Zhou <xzhou@redhat.com>
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
|
|
It is invalid to call del_gendisk() when disk->queue is NULL. Fix error
handling in axon_ram_probe() to avoid doing that.
Also del_gendisk() does not drop a reference to gendisk allocated by
alloc_disk(). That has to be done by put_disk(). Add that call where
needed.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
To avoid recursion on the kernel stack when stacked block devices
are in use, generic_make_request() will, when called recursively,
queue new requests for later handling. They will be handled when the
make_request_fn for the current bio completes.
If any bios are submitted by a make_request_fn, these will ultimately
be handled seqeuntially. If the handling of one of those generates
further requests, they will be added to the end of the queue.
This strict first-in-first-out behaviour can lead to deadlocks in
various ways, normally because a request might need to wait for a
previous request to the same device to complete. This can happen when
they share a mempool, and can happen due to interdependencies
particular to the device. Both md and dm have examples where this happens.
These deadlocks can be erradicated by more selective ordering of bios.
Specifically by handling them in depth-first order. That is: when the
handling of one bio generates one or more further bios, they are
handled immediately after the parent, before any siblings of the
parent. That way, when generic_make_request() calls make_request_fn
for some particular device, we can be certain that all previously
submited requests for that device have been completely handled and are
not waiting for anything in the queue of requests maintained in
generic_make_request().
An easy way to achieve this would be to use a last-in-first-out stack
instead of a queue. However this will change the order of consecutive
bios submitted by a make_request_fn, which could have unexpected consequences.
Instead we take a slightly more complex approach.
A fresh queue is created for each call to a make_request_fn. After it completes,
any bios for a different device are placed on the front of the main queue, followed
by any bios for the same device, followed by all bios that were already on
the queue before the make_request_fn was called.
This provides the depth-first approach without reordering bios on the same level.
This, by itself, it not enough to remove all deadlocks. It just makes
it possible for drivers to take the extra step required themselves.
To avoid deadlocks, drivers must never risk waiting for a request
after submitting one to generic_make_request. This includes never
allocing from a mempool twice in the one call to a make_request_fn.
A common pattern in drivers is to call bio_split() in a loop, handling
the first part and then looping around to possibly split the next part.
Instead, a driver that finds it needs to split a bio should queue
(with generic_make_request) the second part, handle the first part,
and then return. The new code in generic_make_request will ensure the
requests to underlying bios are processed first, then the second bio
that was split off. If it splits again, the same process happens. In
each case one bio will be completely handled before the next one is attempted.
With this is place, it should be possible to disable the
punt_bios_to_recover() recovery thread for many block devices, and
eventually it may be possible to remove it completely.
Ref: http://www.spinics.net/lists/raid/msg54680.html
Tested-by: Jinpu Wang <jinpu.wang@profitbricks.com>
Inspired-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
Fabio Estevam
Marek Vasut
Stefan Agner
David Hildenbrand
OGAWA Hirofumi
Bartlomiej Zolnierkiewicz
Dmitry Vyukov
Tahsin Erdogan
Kirill A. Shutemov
AKASHI Takahiro
Andrea Arcangeli
Mike Rapoport
Laurent Dufour
Masanari Iida
Yisheng Xie
Arnd Bergmann
Dan Williams
Aneesh Kumar K.V
Masahiro Yamada
Alex Deucher
Wolfram Sang
Javier Martinez Canillas
Jim Qu
Tony Luck
Linus Torvalds
Christoph Hellwig
Brian Foster
Jan Kara
NeilBrown