| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The write accesses to LOGICAL_PAGE_{DATA,SPARE}_SIZE have no effect
because the Denali User's Guide says these registers are read-only.
The hardware automatically multiplies the main/spare size by the
number of devices and update LOGICAL_PAGE_{DATA,SPARE}_SIZE.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Currently, the driver expects DEVICE_CONNECTED is automatically set
by the hardware, but this feature is disabled in some cases.
In such cases, it is the software's responsibility to set up the
DEVICES_CONNECTED register.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The available configuration of the IP bus width is x8 or x16, so the
possible value for denali->devnum is 1 or 2.
If the value is 1, there is nothing to do. Fixup parameters only
when denali->devnum is 2.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Collect multi NAND fixups into a helper function instead of
scattering them in denali_init().
I am rewording the comment block to clearly explain what is called
"multi device".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
This will allow nand_dt_init() to parse DT properties in the NAND
controller device node.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The denali_init() needs to setup a bunch of parameters of nand_chip.
Replace denali->nand.(member) with chip->(member) for shorter code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Set Features (0xEF) command toggles the R/B# pin after 4 sub feature
parameters are written.
Currently, nand_command(_lp) calls chip->dev_ready immediately after
the address cycle because NAND_CMD_SET_FEATURES falls into default:
label. No wait is needed at this point.
If you see nand_onfi_set_features(), R/B# is already cared by the
chip->waitfunc call.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Read ID (0x90) command does not toggle the R/B# pin. Without this
patch, NAND_CMD_READID falls into the default: label, then R/B# is
checked by chip->dev_ready().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The page number is generally stored in an integer type variable.
The uint16_t does not have enough width. I see no reason to use
uint32_t for other members, either. Just use int.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The Denali NAND controller IP has various customizable features.
SoC vendors can choose desired functions when a delivery RTL is
created. It means there are several variants for this IP. For
example, the Intel version is equipped with 32bit DMA, whereas the
IP for UniPhier SoC family with 64bit DMA.
This driver was originally written for some Intel platforms with
Intel specific things hard-coded. What is worse, the revision
register of this IP does not work to distinguish such features.
We need to do something to make the driver available for other SoCs.
Let's introduce a caps member to the denali_nand_info structure to
switch on/off various features. Also, add struct denali_dt_data to
store the capability associated with compatible string.
Boris suggested this approach in discussion [1] instead of a new DT
property for every feature.
[1] https://lkml.org/lkml/2016/3/29/142
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The interrupts are enabled by INTR_EN register, then asserted
interrupts can be observed via INTR_STATUS register.
The bit fields are identical between INTR_EN and INTR_STATUS, so we
can merge the bit field macros. Likewise for DATA_INTR.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The same comment "Mapped io reg base address" for flash_reg and
flash_mem probably due to the mistake of copy-paste work.
Of course, the latter is not the register base address.
Reword the comments using the terminology in the Denali User's Guide.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
These members are not used at all.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
This macro is defined twice in denali.c (around line 98 and
line 651), so remove the second one.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
All of these macros are not used at all.
CONFIG_MTD_NAND_DENALI_SCRATCH_REG_ADDR is not used for anything but
defining SCRATCH_REG_ADDR. The config option should go away as well.
I am removing some register macros. They are not used, and do not
exist in recent IP versions.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The nand_default_block_markbad() and scan_block_fast() use high
level APIs to get access to the BBM.
On the other hand, nand_block_bad (the default implementation of
->block_bad) calls the lower level ->cmdfunc hook. This prevents
drivers from using ->ecc.read_oob() even if optimized read operation
is implemented. Besides, some NAND controllers may protect the BBM
with ECC.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Currently, it is valid to specify both "nand-ecc-step-size" and
"nand-ecc-strength", but not allowed to set only one of them.
This requirement has a conflict with "nand-ecc-maximize"; this flag
is used when you want the driver to choose the best ECC strength.
If "nand-ecc-maximize" is set, "nand-ecc-strength" is very likely to
be unset.
It would be possible to make the if-conditional more complex by
adding the check for the NAND_ECC_MAXIMIZE flag, but I chose to drop
the check entirely. I thought of the situation where the hardware
has a fixed ECC step size (so it can be hard-coded in the driver),
whereas the ECC strength is configurable by software. In that case,
we may want to only set "nand-ecc-strength" (or "nand-ecc-maximize")
in DT.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Since commit 4404d7d821c33 ("mtd: nand: fsmc: remove stale non-DT probe
path"), the fsmc NAND driver only supports Device Tree probing, and
therefore has a "depends on OF" in its Kconfig option.
Due to this the #ifdef CONFIG_OF ... #endif condition in the driver code
is no longer necessary.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
These definitions are not used anywhere in the driver, so remove them.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
This commit switches the fsmc_nand driver from clk_get() to
devm_clk_get(), which saves a few clk_put().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Since the driver now only supports DT probing, it doesn't make a lot of
sense to have a private data structure called platform_data, fill it in
with information coming from the DT, and then copying this into the
driver-specific structure fsmc_nand_data.
So instead, we remove fsmc_nand_platform_data entirely, and have
fsmc_nand_probe_config_dt() fill in the fsmc_nand_data structure
directly.
This requires calling fsmc_nand_probe_config_dt() after fsmc_nand_data
has been allocated instead of before.
Also, as an added bonus, we now propagate properly the return value of
fsmc_nand_probe_config_dt() instead of returning -ENODEV on failure. The
error message is also removed, since it no longer made any sense.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
It is already done a few lines before.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The ->partitions and ->nr_partitions fields of struct
fsmc_nand_platform_data are never set anywhere, so they are always
NULL/0. The corresponding fields in 'struct fsmc_nand_data' are set to the
value of the same fields in fsmc_nand_platform_data, i.e NULL/0.
Therefore, we remove those two fields, and pass NULL/0 directly to
mtd_device_register(), like many other NAND drivers already do.
At the same time, we remove the comment about the fact that we pass
partition info, since we are no longer doing this.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The read_dma_priv and write_dma_priv fields of fsmc_nand_platform_data
are never set, so this commit removes them.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
host->select_chip used to point to the ->select_bank() function provided
by the platform data, but the latter no longer exists. Therefore
host->select_chip is always NULL.
Due to this, the fsmc_select_chip() does nothing, except:
chip->cmd_ctrl(mtd, NAND_CMD_NONE, 0 | NAND_CTRL_CHANGE);
when chipnr is -1, which is exactly what the default implementation of
->select_chip() does in the NAND framework. So, this commit kills
fsmc_select_chip() entirely.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Since commit 4404d7d821c3 ("mtd: nand: fsmc: remove stale non-DT probe
path"), only DT probing is used for the fsmc_nand driver. Due to this,
the ->select_bank() field of fsmc_nand_platform_data is never used, so
this commit gets rid of it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
This commit simply moves the "struct fsmc_nand_data" definition to be
towards the beginning of the file, with the other defines and type
definitions, instead of in the middle of the driver code. This is much
more consistent with what most Linux drivers do.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
In commit eea628199d5b ("mtd: Add device-tree support to fsmc_nand"),
Device Tree support was added to the fmsc_nand driver. However, this
code has a bug in how it handles the bank-width DT property to set the
bus width.
Indeed, in the function fsmc_nand_probe_config_dt() that parses the
Device Tree, it sets pdata->width to either 8 or 16 depending on the
value of the bank-width DT property.
Then, the ->probe() function will test if pdata->width is equal to
FSMC_NAND_BW16 (which is 2) to set NAND_BUSWIDTH_16 in
nand->options. Therefore, with the DT probing, this condition will never
match.
This commit fixes that by removing the "width" field from
fsmc_nand_platform_data and instead have the fsmc_nand_probe_config_dt()
function directly set the appropriate nand->options value.
It is worth mentioning that if this commit gets backported to older
kernels, prior to the drop of non-DT probing, then non-DT probing will
be broken because nand->options will no longer be set to
NAND_BUSWIDTH_16.
Fixes: eea628199d5b ("mtd: Add device-tree support to fsmc_nand")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
We should be return -ENOMEM instead of success.
Fixes: 626994e07480 ("mtd: nand: hynix: Add read-retry support for 1x nm MLC NANDs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
On some hardware, the nCE signal is wired to the ChipSelect associated
to bus address of the NAND, so it is automatically driven during the
memory access and it is not managed by a GPIO.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
As NAND support for Freescale/NXP IFC controller is available on
LS1021A, the dependency for LS1021A is added.
LS1021A is an earlier product and is not compatible with later
LayerScape architecture. So ARCH_LAYERSCAPE can't cover LS1021A.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
As Freescale/NXP IFC controller is available on LS1021A, the dependency
for LS1021A is added.
LS1021A is an earlier product and is not compatible with later
LayerScape architecture. So ARCH_LAYERSCAPE can't cover LS1021A.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
do_dma() uses an int to pass the DMA data direction information and
pass the same value to dmaengine_prep_slave_sg().
Currently, DMA_{FROM,TO}_DEVICE match DMA_{DEV_TO_MEM,MEM_TO_DEV}
definitions so it works fine, but assuming this will always be the case
is not safe.
Enforce enum dma_data_direction type in the function prototype and make
the enum dma_data_direction -> enum dma_transfer_direction conversion
explicit.
Reported-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
|
|
trivial fix to spelling mistake in NS_ERR error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
As of commit bb475230b8e5 ("reset: make optional functions really
optional"), the reset framework API calls use NULL pointers to describe
optional, non-present reset controls.
This allows to return errors from devm_reset_control_get_optional and to
call reset_control_(de)assert unconditionally.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
All Hynix MLC NANDs produced with the 1x nm process support read-retry.
This read retry implementation should also be re-usable for other Hynix
NANDs, but the method to retrieve the read-retry parameters from the
read-retry OTP area might change a bit (some NANDs are even using a fixed
set of values instead of retrieving those information from the OTP area).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Richard Weinberger <richard@nod.at>
|
|
The current NAND ID detection in nand_hynix.c is not handling the
different scheme used by Hynix, thus forcing developers to add new
entry to the nand_ids table each time they want to support a new MLC
NAND.
Enhance the detection logic to handle all known formats. This does not
necessarily mean we are handling all the cases, but if new formats are
discovered, the code should evolve to take them into account instead of
adding more full-id entries to the nand_ids table.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Richard Weinberger <richard@nod.at>
|
|
On some nand controllers with hw-ecc the controller code wants to know
the ecc strength and size and having these as 0, 0 is not accepted.
Specifying these in devicetree is possible but undesirable as the nand
may be different in different production runs of the same board, so it
is better to get this info from the nand id where possible.
This commit adds code to read the ecc strength and size from the nand
for Samsung extended-id nands. This code is based on the info for the 5th
id byte in the datasheets for the following Samsung nands: K9GAG08U0E,
K9GAG08U0F, K9GAG08X0D, K9GBG08U0A, K9GBG08U0B. These all use these bits
in the exact same way.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Move Macronix specific initialization logic into nand_macronix.c. This
is part of the "separate vendor specific code from core" cleanup
process.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Move AMD/Spansion specific initialization/detection logic into
nand_amd.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Richard Weinberger <richard@nod.at>
|
|
Move Micron specific initialization logic into nand_micron.c. This is
part of the "separate vendor specific code from core" cleanup process.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Richard Weinberger <richard@nod.at>
|
|
Move Toshiba specific initialization and detection logic into
nand_toshiba.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Richard Weinberger <richard@nod.at>
|
|
Move Hynix specific initialization and detection logic into
nand_hynix.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Richard Weinberger <richard@nod.at>
|
|
Move Samsung specific initialization and detection logic into
nand_samsung.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Richard Weinberger <richard@nod.at>
|
|
A lot of NANDs are implementing generic features in a non-generic way,
or are providing advanced auto-detection logic where the NAND ID bytes
meaning changes with the NAND generation.
Providing this vendor specific initialization step will allow us to get
rid of full-id entries in the nand_ids table or all the vendor specific
cases added over the time in the generic NAND ID decoding logic.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
There is no reason to expose the NAND manufacturer table. Provide an
helper function to find manufacturers by their id.
We also turn the nand_manufacturers table into a const array, since its
members are not modified after the initial assignment.
Finally, we remove the sentinel manufacturer entry from the manufacturers
table (we already have the array size information given by ARRAY_SIZE()),
and add the nand_manufacturer_name() helper to handle the "Unknown" case
properly.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
MTD_NAND_IDS is selected by MTD_NAND, which makes it useless. Remove
the Kconfig option and link nand_ids.o into the nand.o object file.
Doing that also prevents creating an extra nand_ids.ko module when
MTD_NAND is activated as a module.
Since nand_ids.c is no longer compiled as a standalone module and the
nand_manuf_ids/nand_flash_ids symbols are only used in nand_base.c, we
can get rid of the MODULE_XXX() and EXPORT_SYMBOL() definitions.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Drop the 's' at the end of nand_manufacturers since the struct is actually
describing a single manufacturer, not a manufacturer table.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Since commit 4722c0e958e6 ("mtd: nand: change return type of
nand_get_flash_type() to int"), nand_get_flash_type() no longer returns
a nand_flash_dev object.
Rename the function to match this new behavior.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Richard Weinberger <richard@nod.at>
|
|
Auto-detection functions are passed a busw parameter to retrieve the actual
NAND bus width and eventually set the correct value in chip->options.
Rework the nand_get_flash_type() function to get rid of this extra
parameter and let detection code directly set the NAND_BUSWIDTH_16 flag in
chip->options if needed.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
|
Masahiro Yamada
Thomas Petazzoni
Dan Carpenter
Christophe Leroy
Alison Wang
Boris Brezillon
Colin Ian King
Philipp Zabel
Hans de Goede