| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
On SuperH, the base of the physical memory might be different from
zero. In this case, PCI address zero will map to a non-zero physical
address. In order to make sure that the DMA mapping API takes care of
this DMA offset, we must fill in the dev->dma_pfn_offset field for PCI
devices. This gets done in the pcibios_bus_add_device() hook, called
for each new PCI device detected.
The dma_pfn_offset global variable is re-calculated for every PCI
controller available on the platform, but that's not an issue because
its value will each time be exactly the same, as it only depends on
the memory start address and memory size.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Rich Felker <dalias@libc.org>
|
|
The code setting up the PCI -> SuperHighway mapping doesn't take into
account the fact that the address stored in PCIELARx must be aligned
with the size stored in PCIELAMRx.
For example, when your physical memory starts at 0x0800_0000 (128 MB),
a size of 64 MB or 128 MB is fine. However, if you have 256 MB of
memory, it doesn't work because the base address is not aligned on the
size.
In such situation, we have to round down the base address to make sure
it is aligned on the size of the area. For for a 0x0800_0000 base
address with 256 MB of memory, we will round down to 0x0, and extend
the size of the mapping to 512 MB.
This allows the mapping to work on platforms that have 256 MB of
RAM. The current setup would only work with 128 MB of RAM or less.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Rich Felker <dalias@libc.org>
|
|
The current definition of the PCIe IO and MEM resources for SH7786
doesn't match what the datasheet says. For example, for PCIe0
0xfe100000 is advertised by the datasheet as a PCI IO region, while
0xfd000000 is advertised as a PCI MEM region. The code currently
inverts the two.
The SH4A_PCIEPARL and SH4A_PCIEPTCTLR registers allow to define the
base address and role of the different regions (including whether it's
a MEM or IO region). However, practical experience on a SH7786 shows
that if 0xfe100000 is used for LEL and 0xfd000000 for IO, a PCIe
device using two MEM BARs cannot be accessed at all. Simply using
0xfe100000 for IO and 0xfd000000 for MEM makes the PCIe device
accessible.
It is very likely that this was never seen because there are two other
PCI MEM region listed in the resources. However, for different
reasons, none of the two other MEM regions are usable on the specific
SH7786 platform the problem was encountered. Therefore, the last MEM
region at 0xfe100000 was used to place the BARs, making the device
non-functional.
This commit therefore adjusts those PCI MEM and IO resources
definitions so that they match what the datasheet says. They have only
been tested with PCIe 0.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Rich Felker <dalias@libc.org>
|
|
Depending on the physical memory layout, some PCI MEM areas are not
usable. According to the SH7786 datasheet, the PCI MEM area from
1000_0000 to 13FF_FFFF is only usable if the physical memory layout
(in MMSELR) is 1, 2, 5 or 6. In all other configurations, this PCI MEM
area is not usable (because it overlaps with DRAM).
Therefore, this commit adjusts the PCI SH7786 initialization to mark
the relevant PCI resource as IORESOURCE_DISABLED if we can't use it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Rich Felker <dalias@libc.org>
|
|
Some PCI MEM resources are marked as IORESOURCE_MEM_32BIT, which means
they are only usable when the SH core runs in 32-bit mode. In 29-bit
mode, such memory regions are not usable.
The existing code for SH7786 properly skips such regions when
configuring the PCIe controller registers. However, because such
regions are still described in the resource array, the
pcibios_scanbus() function in the SuperH pci.c will register them to
the PCI core. Due to this, the PCI core will allocate MEM areas from
this resource, and assign BARs pointing to this area, even though it's
unusable.
In order to prevent this from happening, we mark such regions as
IORESOURCE_DISABLED, which tells the SuperH pci.c pcibios_scanbus()
function to skip them.
Note that we separate marking the region as disabled from skipping it,
because other regions will be marked as disabled in follow-up patches.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Rich Felker <dalias@libc.org>
|
|
In pcibios_scanbus(), we provide to the PCI core the usable MEM and IO
regions using pci_add_resource_offset(). We travel through all
resources available in the "struct pci_channel".
Also, in register_pci_controller(), we travel through all resources to
request them, making sure they don't conflict with already requested
resources.
However, some resources may be disabled, in which case they should not
be requested nor provided to the PCI core.
In the current situation, none of the resources are disabled. However,
follow-up patches in this series will make some resources disabled,
making this preliminary change necessary.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Rich Felker <dalias@libc.org>
|
|
Some devices may have a non-zero DMA offset, i.e an offset between the
DMA address and the physical address. Such an offset can be encoded
into the dma_pfn_offset field of "struct device", but the SuperH
implementation of the DMA mapping API does not observe this
information.
This commit fixes that by ensuring the DMA address is properly
calculated depending on this DMA offset.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Rich Felker <dalias@libc.org>
|
|
The SH7786 has different physical memory layout configurations,
configurable through the MMSELR register. The configuration is
typically defined by the bootloader, so Linux generally doesn't care.
Except that depending on the configuration, some PCI MEM areas may or
may not be available. This commit adds a helper function that allows
to retrieve the current physical memory layout configuration. It will
be used in a following patch to exclude unusable PCI MEM areas during
the PCI initialization.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Rich Felker <dalias@libc.org>
|
|
When responding to a debug trap (breakpoint) in userspace, the
kernel's trap handler raised SIGTRAP but returned from the trap via a
code path that ignored pending signals, resulting in an infinite loop
re-executing the trapping instruction.
Signed-off-by: Rich Felker <dalias@libc.org>
|
|
unflatten_device_tree() makes use of memblock allocation, and
therefore must be called before paging_init() migrates the memblock
allocation data to the bootmem framework. Otherwise the record of the
allocation for the expanded device tree will be lost, and will
eventually be clobbered when allocated for another use.
Signed-off-by: Rich Felker <dalias@libc.org>
|
|
Commit 00b73d8d1b71 ("sh: add working futex atomic ops on userspace
addresses for smp") changed the futex_atomic_op_inuser function to
use a loop. In case of the FUTEX_OP_SET op with a userspace address
containing a value different of 0, this loop is an endless loop.
Fix that by loading the value of oldval from the userspace before doing
the cmpxchg op, also for the FUTEX_OP_SET case.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Rich Felker <dalias@libc.org>
|
|
This seems to cause flickering and lock-ups for a wide range of users.
Revert until we've found a proper fix for the flickering and lock-ups.
This reverts commit 36cc549d59864b7161f0e23d710c1c4d1b9cf022.
Cc: Shirish S <shirish.s@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This reverts commit cd2d6c92a8e39d7e50a5af9fcc67d07e6a89e91d.
Cc: Shirish S <shirish.s@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Hardware understands the regamma LUT as a piecewise linear function,
with points spaced exponentially along the range. We previously
programmed the LUT for range [2^-10, 2^0). This causes (normalized)
color values of 1 (=2^0) to miss the programmed LUT, and fall onto the
end region.
For DCE, the end region is extrapolated using a single (base, slope)
pair, using the max y-value from the last point in the curve as base.
This presents a problem, since this value affects all three color
channels. Scaling down the intensity of say - the blue regamma curve -
will not affect it's end region. This is especially noticiable when
using RedShift. It scales down the blue and green channels, but leaves
full-intensity colors unshifted.
Therefore, extend the range to cover [2^-10, 2^1) by programming another
hardware segment, containing only one point. That way, we won't be
hitting the end region.
Note that things are a bit different for DCN, since the end region can
be set per-channel.
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This patch simply fixes some comments and the gfs2-glocks.txt file:
Places where i_rwsem was called i_mutex, and adding i_rw_mutex.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
|
|
Function rhashtable_walk_peek is problematic because there is no
guarantee that the glock previously returned still exists; when that key
is deleted, rhashtable_walk_peek can end up returning a different key,
which will cause an inconsistent glock dump. Fix this by keeping track
of the current glock in the seq file iterator functions instead.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
|
|
Put a lockref unless the lockref is dead or its count would become zero.
This is the same as lockref_put_or_lock except that the lock is never
left held.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
|
|
The nvmf_check_if_ready() checks that were added are very simplistic.
As such, the routine allows a lot of cases to fail ios during windows
of reset or re-connection. In cases where there are not multi-path
options present, the error goes back to the callee - the filesystem
or application. Not good.
The common routine was rewritten and calling syntax slightly expanded
so that per-transport is_ready routines don't need to be present.
The transports now call the routine directly. The routine is now a
fabrics routine rather than an inline function.
The routine now looks at controller state to decide the action to
take. Some states mandate io failure. Others define the condition where
a command can be accepted. When the decision is unclear, a generic
queue-or-reject check is made to look for failfast or multipath ios and
only fails the io if it is so marked. Otherwise, the io will be queued
and wait for the controller state to resolve.
Admin commands issued via ioctl share a live admin queue with commands
from the transport for controller init. The ioctls could be intermixed
with the initialization commands. It's possible for the ioctl cmd to
be issued prior to the controller being enabled. To block this, the
ioctl admin commands need to be distinguished from admin commands used
for controller init. Added a USERCMD nvme_req(req)->rq_flags bit to
reflect this division and set it on ioctls requests. As the
nvmf_check_if_ready() routine is called prior to nvme_setup_cmd(),
ensure that commands allocated by the ioctl path (actually anything
in core.c) preps the nvme_req(req) before starting the io. This will
preserve the USERCMD flag during execution and/or retry.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.e>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Commit 42de82a8b544 previously attempted to fix this, and it did
correctly pad the MN and FR fields with spaces, but the SN field still
contains 0 bytes. The current code fills out the first 16 bytes with
hex2bin, leaving the last 4 bytes zeroed. Rather than adding a lot of
error-prone math to avoid overwriting SN twice, just set the whole thing
to spaces up front (it's only 20 bytes).
Fixes: 42de82a8b544 ("nvmet: don't report 0-bytes in serial number")
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Also add error flow in case srcu initialization function fails.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We have to increment the number of logical blocks to a 1's based value
in the native format prior to converting to 512b units.
Signed-off-by: Rodrigo R. Galvao <rosattig@linux.vnet.ibm.com>
[changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The admin and first IO queues shared the first irq vector, which has an
affinity mask including cpu0. If a system allows cpu0 to be offlined,
the admin queue may not be usable if no other CPUs in the affinity mask
are online. This is a problem since unlike IO queues, there is only
one admin queue that always needs to be usable.
To fix, this patch allocates one pre_vector for the admin queue that
is assigned all CPUs, so will always be accessible. The IO queues are
assigned the remaining managed vectors.
In case a controller has only one interrupt vector available, the admin
and IO queues will share the pre_vector with all CPUs assigned.
Cc: Jianchao Wang <jianchao.w.wang@oracle.com>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
All the queue memory is allocated up front. We don't take the node
into consideration when creating queues anymore, so removing the unused
parameter.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
User reported controller always retains CSTS.RDY to 1, which fails
controller disabling when resetting the controller. This is also before
the admin queue is allocated, and trying to disable an unallocated queue
results in a NULL dereference.
Reported-by: Alex Gagniuc <Alex_Gagniuc@Dellteam.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
nvmet_execute_get_disc_log_page() passes a fixed-length string into
nvmet_format_discovery_entry(), which then does a longer memcpy() on
it, as pointed out by gcc-8:
In function 'nvmet_format_discovery_entry',
inlined from 'nvmet_execute_get_disc_log_page' at drivers/nvme/target/discovery.c:126:4:
drivers/nvme/target/discovery.c:62:2: error: 'memcpy' forming offset [38, 223] is out of the bounds [0, 37] [-Werror=array-bounds]
memcpy(e->subnqn, subsys_nqn, NVMF_NQN_SIZE);
Using strncpy() will make this well-defined, filling the rest of the
buffer with zeroes, under the assumption that the input is either
a NUL-terminated string, or a byte sequence containing no zeroes.
If the input is a string that is longer than NVMF_NQN_SIZE, we
continue to have no NUL-termination in the output.
Fixes: a07b4970f464 ("nvmet: add a generic NVMe target")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
NVMe over Fabrics 1.0 Section 5.2 "Discovery Controller Properties and
Command Support" Figure 31 "Discovery Controller – Admin Commands"
explicitly listst all commands but "Get Log Page" and "Identify" as
reserved, but NetApp report the Linux host is sending Keep Alive
commands to the discovery controller, which is a violation of the
Spec.
We're already checking for discovery controllers when configuring the
keep alive timeout but when creating a discovery controller we're not
hard wiring the keep alive timeout to 0 and thus remain on
NVME_DEFAULT_KATO for the discovery controller.
This can be easily remproduced when issuing a direct connect to the
discovery susbsystem using:
'nvme connect [...] --nqn=nqn.2014-08.org.nvmexpress.discovery'
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Fixes: 07bfcd09a288 ("nvme-fabrics: add a generic NVMe over Fabrics library")
Reported-by: Martin George <marting@netapp.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
nvme_start_keep_alive() isn't used outside core.c so unexport it and
make it static.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When nvmet_req_init() fails, __nvmet_req_complete() is called
to handle the target request via .queue_response(), so
nvme_loop_queue_response() shouldn't be called again for
handling the failure.
This patch fixes this case by the following way:
- move blk_mq_start_request() before nvmet_req_init(), so
nvme_loop_queue_response() may work well to complete this
host request
- don't call nvme_cleanup_cmd() which is done in nvme_loop_complete_rq()
- don't call nvme_loop_queue_response() which is done via
.queue_response()
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
[trimmed changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Compiling on 32 bits system produces a warning for the shift width
when shifting 32 bit integer with 64bit integer.
Make sure that offset always is 64bit, and use macros for retrieving
lower and upper bits of the offset.
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We can't use l2tp_tunnel_find() to prevent l2tp_nl_cmd_tunnel_create()
from creating a duplicate tunnel. A tunnel can be concurrently
registered after l2tp_tunnel_find() returns. Therefore, searching for
duplicates must be done at registration time.
Finally, remove l2tp_tunnel_find() entirely as it isn't use anywhere
anymore.
Fixes: 309795f4bec2 ("l2tp: Add netlink control API for L2TP")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
l2tp_tunnel_create() inserts the new tunnel into the namespace's tunnel
list and sets the socket's ->sk_user_data field, before returning it to
the caller. Therefore, there are two ways the tunnel can be accessed
and freed, before the caller even had the opportunity to take a
reference. In practice, syzbot could crash the module by closing the
socket right after a new tunnel was returned to pppol2tp_create().
This patch moves tunnel registration out of l2tp_tunnel_create(), so
that the caller can safely hold a reference before publishing the
tunnel. This second step is done with the new l2tp_tunnel_register()
function, which is now responsible for associating the tunnel to its
socket and for inserting it into the namespace's list.
While moving the code to l2tp_tunnel_register(), a few modifications
have been done. First, the socket validation tests are done in a helper
function, for clarity. Also, modifying the socket is now done after
having inserted the tunnel to the namespace's tunnels list. This will
allow insertion to fail, without having to revert theses modifications
in the error path (a followup patch will check for duplicate tunnels
before insertion). Either the socket is a kernel socket which we
control, or it is a user-space socket for which we have a reference on
the file descriptor. In any case, the socket isn't going to be closed
from under us.
Reported-by: syzbot+fbeeb5c3b538e8545644@syzkaller.appspotmail.com
Fixes: fd558d186df2 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The API docs describe i2c_transfer() as taking a pointer to an array
of i2c_msg containing at least 1 entry, but leaves it to the individual
drivers to sanity check the msgs and num parameters. Let's do this in
core code instead.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[wsa: changed '<= 0' to '< 1']
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Intentionally missing i2c-riic here, Chris Brandt will add himself for
that one later.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The number of I2C host controller drivers keeps increasing, and although
I had some success acquiring specific driver maintainers, my bandwidth
is by far not enough to act as a fallback for the rest of the drivers.
To reflect this status-quo in MAINTAINERS, add a separate entry for I2C
host drivers, let the I2C list (= community) be the contact point, and
mark this section as "Odd fixes".
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
|
|
On some systems, the BIOS expects certain SMBus register values to
match the hardware defaults. Restore these configuration registers at
shutdown time to avoid confusing the BIOS. This avoids hard-locking
such systems upon reboot.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jason Andryuk <jandryuk@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@vger.kernel.org
|
|
Saving the original value of register SMBSLVCMD in
i801_enable_host_notify() doesn't work, because this function is
called not only at probe time but also at resume time. Do it in
i801_probe() instead, so that the saved value is not overwritten at
resume time.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 22e94bd6779e ("i2c: i801: store and restore the SLVCMD register at load and unload")
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Jason Andryuk <jandryuk@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@vger.kernel.org # v4.10+
|
|
When issuing a "shutdown -h now", the reboot syscall calls kernel_halt()
which shouldn't return, otherwise one gets this panic:
reboot: System halted
Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000000
CPU: 0 PID: 1 Comm: systemd-shutdow Not tainted 4.16.0-32bit+ #560
Backtrace:
[<1018a694>] show_stack+0x18/0x28
[<106e68a8>] dump_stack+0x80/0x10c
[<101a4df8>] panic+0xfc/0x290
[<101a90b8>] do_exit+0x73c/0x914
[<101c7e38>] SyS_reboot+0x190/0x1d4
[<1017e444>] syscall_exit+0x0/0x14
Fix it by letting machine_halt() call machine_power_off() which doesn't
return.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
I added dumping of link information about tun devices over netlink in
commit 1ec010e70593 ("tun: export flags, uid, gid, queue information
over netlink"), but didn't add the missing netlink notifications when
the device's exported properties change.
This patch adds notifications when owner/group or flags are modified,
when queues are attached/detached, and when a tun fd is closed.
Reported-by: Thomas Haller <thaller@redhat.com>
Fixes: 1ec010e70593 ("tun: export flags, uid, gid, queue information over netlink")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Otherwise, register_netdevice advertises the creation of the device with
the default flags, instead of what the user requested.
Reported-by: Thomas Haller <thaller@redhat.com>
Fixes: 1ec010e70593 ("tun: export flags, uid, gid, queue information over netlink")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 92571a1aae40 ("lan78xx: Connect phy early") moves the PHY
initialisation into lan78xx_probe, but lan78xx_open subsequently calls
lan78xx_reset. As well as forcing a second round of link negotiation,
this reset frequently prevents the phy interrupt from being generated
(even though the link is up), rendering the interface unusable.
Fix this issue by removing the lan78xx_reset call from lan78xx_open.
Fixes: 92571a1aae40 ("lan78xx: Connect phy early")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When open fails during ethtool -L ring change, for example, the driver
may crash at bnxt_free_irq() because bp->bnapi is NULL.
If we fail to allocate all the new rings, bnxt_open_nic() will free
all the memory including bp->bnapi. Subsequent call to bnxt_close_nic()
will try to dereference bp->bnapi in bnxt_free_irq().
Fix it by checking for !bp->bnapi in bnxt_free_irq().
Fixes: e5811b8c09df ("bnxt_en: Add IRQ remapping logic.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With recent changes to reserve both L2 and RDMA rings, we need to include
the RDMA rings in bnxt_check_rings(). Otherwise we will under-estimate
the rings we need during ethtool -L and may lead to failure.
Fixes: fbcfc8e46741 ("bnxt_en: Reserve completion rings and MSIX for bnxt_re RDMA driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While a VF is configured with a bigger mtu (> 1500), any packets that
are punted to the VF-rep (slow-path) get dropped by OVS kernel-datapath
with the following message: "dropped over-mtu packet". Fix this by
returning the max-mtu value for a VF-rep derived from its corresponding VF.
VF-rep's mtu can be changed using 'ip' command as shown in this example:
$ ip link set bnxt0_pf0vf0 mtu 9000
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver currently uses src port field (along with other fields) in the
decap tunnel key, while looking up and adding tunnel nodes. This leads to
redundant cfa_decap_filter_alloc() requests to the FW and flow-miss in the
flow engine. Fix this by ignoring the src port field in decap tunnel nodes.
Fixes: f484f6782e01 ("bnxt_en: add hwrm FW cmds for cfa_encap_record and decap_filter")
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before this patch the following commands would succeed as far as the
user was concerned:
$ tc qdisc add dev p1p1 ingress
$ tc filter add dev p1p1 parent ffff: protocol all \
flower skip_sw action drop
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
flower skip_sw src_mac 00:02:00:00:00:01/44 action drop
The current flow offload infrastructure used does not support wildcard
matching for ethernet headers, so do not allow the second or third
commands to succeed. If a user wants to drop traffic on that interface
the protocol and MAC addresses need to be specified explicitly:
$ tc qdisc add dev p1p1 ingress
$ tc filter add dev p1p1 parent ffff: protocol arp \
flower skip_sw action drop
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
flower skip_sw action drop
...
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
flower skip_sw src_mac 00:02:00:00:00:01 action drop
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
flower skip_sw src_mac 00:02:00:00:00:02 action drop
...
There are also checks for VLAN parameters in this patch as other callers
may wildcard those parameters even if tc does not. Using different
flow infrastructure could allow this to work in the future for L2 flows,
but for now it does not.
Fixes: 2ae7408fedfe ("bnxt_en: bnxt: add TC flower filter offload support")
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix ethtool .get_rxfh() crash by checking for valid indirection table
address before copying the data.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding missing call to cache current backlight values.
Otherwise the brightness resets to default value on resume.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
Thomas Petazzoni
Rich Felker
Aurelien Jarno
Harry Wentland
Leo (Sunpeng) Li
Roman Li
Bob Peterson
Andreas Gruenbacher
James Smart
Keith Busch
Daniel Verkamp
Max Gurtovoy
Rodrigo R. Galvao
Arnd Bergmann
Johannes Thumshirn
Ming Lei
Matias Bjørling
Guillaume Nault
Ard Biesheuvel
Wolfram Sang
Wolfram Sang
Jean Delvare
Helge Deller
Sabrina Dubroca
Phil Elwell
Michael Chan
Sriharsha Basavapatna
Andy Gospodarek