| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add charger device node and related battery node for SC2731 PMIC.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This patch adds phandles to the calibration cells provided by the Efuse
device, which is used to calibrate the ADC channel scales.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The Spreadtrum PMIC INTC controller has no registers to set trigger type,
since it is always high level trigger as default. So remove its child
devices' irq trigger type setting and change #interrupt-cells to 1.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Enable the thermal sensor. This device also provides
temperature shutdown protection. The shutdown value is
set at 110C, as tested by the vendor.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
In order to use earlycon, the stdout-path property needs to be set
in the chosen node. All veyron devices use uart2 for debugging, so
add it to the core veyron dtsi.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The mmc1 pins are used for SDIO with a wifi chip.
The function mmc_sdio_switch_hs() only checks for MMC_CAP_SD_HIGHSPEED and
not for MMC_CAP_MMC_HIGHSPEED, so cap-mmc-highspeed can be removed.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This patch fixes a dependency issue with the RPMPD dt bindings. This
temporarily removes the include file and adds hardcoded values for the
OPPs until the other changes full land. This will be addressed in 5.2.
Fixes: 5b6f186f0abb ("arm64: dts: sdm845: Add rpmh powercontroller node")
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Add on-board WiFi/BT support for Rock960 boards such as Rock960 based
on AP6356S and Ficus based on AP6354 wireless modules.
Firmwares for the respective boards are available here:
http://people.linaro.org/~manivannan.sadhasivam/rock960_wifi/
http://people.linaro.org/~manivannan.sadhasivam/ficus_wifi/
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This patch is a port of the fix from
commit 73e42e186699 ("arm64: dts: rockchip: fix rock64 gmac2io stability
issues")
As per that patch, enabling thresh dma mode force disables checksuming.
This is necessary as tx checksuming does not work with packets larger
than 1498.
The rk3328-roc-cc board exhibits tx stability issues with large packets
similar to rock64's issues. This patch resolves that issue.
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
vcc5v0_host and vcc5v0_typec is supplied by vcc5v0_usb and not vcc5v0_sys.
add node for vcc5v0_usb fixed regulator.
Signed-off-by: Akash Gajjar <Akash_Gajjar@mentor.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
lcd panel pinmux is unused and the pin actually for something different,
so removing it.
Signed-off-by: Akash Gajjar <Akash_Gajjar@mentor.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
rename dc12, vcc_sys, vcc1v8_pmu regulators and make it more redable as per the
schematic of rk3399-rockpro64.
Signed-off-by: Akash Gajjar <Akash_Gajjar@mentor.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Describe the Bluetooth portion of the Ampak combo module - this is
either an AP6356S or an AP6212 depending on the board variant, but
there are no relevant compatibility differences between the two.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
TI AM654 SoC has two ADC instances in the MCU domain. Add DT nodes for
the same.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
AM654 SoCs has ADC IP which is similar to AM335x, but without the
touchscreen part. Add new compatible to handle AM654 SoCs. Also, it
seems that existing compatible strings used in the kernel DTs were never
documented. So, document them now.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
Add pinmux for USB1 and enable it as a dual role port.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
Adds support for USB0 and USB1 instances on the AM6 SoC.
USB0 is limited to high-speed for now.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
Main System control module support is added to the device tree to allow
driver to access to their control module registers.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
The AM65 SoC has 2MB MSMC RAM. Add this as a mmio-sram
node so drivers can use it via genpool API.
Following areas are marked reserved:
- Lower 128KB for ATF
- 64KB@0xf0000 for SYSFW
- Upper 1MB for cache
The reserved locations are subject to change at runtime by
the bootloader.
Cc: Nishanth Menon <nm@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Andrew F. Davis <afd@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
Sort the labels in the same order as in the corresponding dtsi file,
in other words, the order of reg address.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add PCIe host controller and PHY nodes. This supports for LD20, PXs3 and
their boards.
This node defines PCIe memory, I/O, and config spaces as follows.
MEM: 20000000-2ffdffff (255MB)
I/O: 2ffe0000-2ffeffff ( 64KB)
CFG: 2fff0000-2fffffff ( 64KB)
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The lcd display of the gta04 has a backlight but the backlight
was not referenced in the lcd node, so screen blanking did
not turn off the backlight. Fix that.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The Bosch Guardian is a TI am335x based device.
It's hardware specifications are as follows:
* 256 MB DDR3 memory
* 512 MB NAND Flash
* USB OTG
* RS232
* MicroSD external storage
* LCD Display interface
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
[tony@atomide.com: updated to use #include]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Most of the legacy "gpio-key,wakeup" boolean property is already
replaced with "wakeup-source". However few occurrences of old property
has popped up again, probably from the remnants in downstream trees.
Replace the legacy properties with the unified "wakeup-source"
property introduced in the commit 700a38b27eef ("Input: gpio_keys -
switch to using generic device properties")
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
The EVM consists of a system on module (SOM) and baseboard, and LCD.
This patch adds a DTSI file for the SOM and baseboard separately,
then a wrapper to combine them and specify processor type and a
LCD information.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Now that all sensors supplied by reg_sensors have supported
regulator control, reg_sensors does NOT need to be always ON,
remove "regulator-always-on" to save power.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The mma8451 sensor driver has supported regulators control,
assign the power supplies for mma8451 to enable the control.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The mag3110 sensor driver has supported regulators control,
assign the power supplies for mag3110 to enable the control.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The isl29023 light sensor driver has supported regulator control,
assign the power supply for isl29023 to enable the control.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add the Zodiac Digital Tapping Unit, a VF610 based network device with
5 Ethernet ports. One of these ports supports 1000Base-T2.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The pfla02 SoM has a Micrel KSZ9031RNX ethernet phy connected to the FEC,
which needs RX and TX clock skew settings to compensate for differences
in line length. The skew values are taken from barebox commit
4c65c20f1071 ("ARM: pfla02: Set new ethernet phy tx timings"), which
is based on patches originally provided by Phytec:
TX_CLK line is approx. 54mm longer than other TX lines which adds
a delay of 0.36ns. RGMII need a delay of min. 1.0ns. This mean we
have to add a delay of 0.64ns. We choose 0.78 to have a little gap.
This can be done by setting GTX pad skew value to 11100
Also add a delay for the RX delay lines, needed for the Duallite
variant. => Set register 2.8 (RGMII Clock Pad Skew) to 0x039F.
Cc: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The DA9063 device need the required "interrupt-controller" property as
documented by the bindings [1].
[1] Documentation/devicetree/bindings/mfd/da9063.txt
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This adds the GPIO line names from the schematics to get them displayed
in the debugfs output of each GPIO controller.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
USB_VBUS is a controlled by a Silergy SY6288CCAC-GP 2A Power
Distribution Switch. The name of it's enable GPIO signal is USB_PWR_EN.
VCC5V is supplied by the main power input called PWR_5V_STB. The name of
it's enable GPIO signal is 3V3_5V_EN.
VCC3V3, VCC_DDR3_1V5 and VCCK (the CPU power supply) each use a separate
Silergy SY8089AAC-GP 2A step down regulator. They are all supplied by the
board's main 5V. VCC3V3 and VCC_DDR3_1V5 are fixed regulators while the
voltage of VCCK can be changed by changing it's feedback voltage via
PWM_C.
VCC1V8 is an ABLIC S-1339D18-M5001-GP fixed voltage regulator which is
supplied by VCC3V3.
VCC_RTC is a Global Mixed-mode Technology Inc. G918T12U-GP LDO which. It
is supplied by either VCC3V3 (when the board is powered) or the RTC coin
cell battery.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The INTR32 pin of the IP101GR Ethernet PHY is routed to the GPIOH_3 pad
on the SoC.
Enable the interrupt function of the PHY's INTR32 pin to switch it from
it's default "receive error" mode to "interrupt pin" mode.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
SAR ADC enabled channel 8 can be used to measure the chip temperature.
This can be made available to the hwmon subsystem by using iio-hwmon.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
SAR ADC enabled channel 8 can be used to measure the chip temperature.
This can be made available to the hwmon subsystem by using iio-hwmon.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
SAR ADC enabled channel 8 can be used to measure the chip temperature.
This can be made available to the hwmon subsystem by using iio-hwmon.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The SAR ADC can measure the chip temperature of the SoC. This only
works if the chip is calibrated and if the calibration data is written
to the correct registers. The calibration data is stored in the upper
two bytes of eFuse offset 0x1f4.
This adds the eFuse cell for the temperature calibration data and
passes it to the SAR ADC. We also need to pass the HHI sysctrl node to
the SAR ADC because the 4th TSC (temperature sensor calibration
coefficient) bit is stored in the HHI region (unlike bits [3:0] which
are stored directly inside the SAR ADC's register area).
On boards that have the SAR ADC enabled channel 8 can be used to
measure the chip temperature.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The SAR ADC can measure the chip temperature of the SoC. This only
works if the chip is calibrated and if the calibration data is written
to the correct registers. The calibration data is stored in the upper
two bytes of eFuse offset 0x1f4.
This adds the eFuse cell for the temperature calibration data and
passes it to the SAR ADC. We also need to pass the HHI sysctrl node to
the SAR ADC because the 4th TSC (temperature sensor calibration
coefficient) bit is stored in the HHI region (unlike bits [3:0] which
are stored directly inside the SAR ADC's register area).
On boards that have the SAR ADC enabled channel 8 can be used to
measure the chip temperature.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The SAR ADC on Meson8m2 is slightly different compared to Meson8. The
ADC functionality is identical but the calibration of the internal
thermal sensor is different.
Use the Meson8m2 specific compatible so the temperature sensor is
calibrated correctly on boards using the Meson8m2 SoC.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The clock controller on Meson8/Meson8m2 and Meson8b is part of a
register region called "HHI". This register area contains more
functionality than just a clock controller:
- the clock controller
- some reset controller bits
- temperature sensor calibration data (on Meson8b and Meson8m2 only)
- HDMI controller
Allow access to this HHI register area as "system controller". Also
migrate the Meson8 and Meson8b clock controllers to this new node.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
According to the Odroid-C1+ schematics the Ethernet TXD1 signal is
routed to GPIOH_5 and the TXD0 signal is routed to GPIOH_6.
The public S805 datasheet shows that TXD0 can be routed to DIF_2_P and
TXD1 can be routed to DIF_2_N instead.
The pin groups eth_txd0_0 (GPIOH_6) and eth_txd0_1 (DIF_2_P) are both
configured as Ethernet TXD0 and TXD1 data lines in meson8b.dtsi. At the
same time eth_txd1_0 (GPIOH_5) and eth_txd1_1 (DIF_2_N) are configured
as TXD0 and TXD1 data lines as well.
This results in a bad Ethernet receive performance. Presumably this is
due to the eth_txd0 and eth_txd1 signal being routed to the wrong pins.
As a result of that data can only be transmitted on eth_txd2 and
eth_txd3. However, I have no scope to fully confirm this assumption.
The vendor u-boot sources for Odroid-C1 use the following Ethernet
pinmux configuration:
SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_6, 0x3f4f);
SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_7, 0xf00000);
This translates to the following pin groups in the mainline kernel:
- register 6 bit 0: eth_rxd1 (DIF_0_P)
- register 6 bit 1: eth_rxd0 (DIF_0_N)
- register 6 bit 2: eth_rx_dv (DIF_1_P)
- register 6 bit 3: eth_rx_clk (DIF_1_N)
- register 6 bit 6: eth_tx_en (DIF_3_P)
- register 6 bit 8: eth_ref_clk (DIF_3_N)
- register 6 bit 9: eth_mdc (DIF_4_P)
- register 6 bit 10: eth_mdio_en (DIF_4_N)
- register 6 bit 11: eth_tx_clk (GPIOH_9)
- register 6 bit 12: eth_txd2 (GPIOH_8)
- register 6 bit 13: eth_txd3 (GPIOH_7)
- register 7 bit 20: eth_txd0_0 (GPIOH_6)
- register 7 bit 21: eth_txd1_0 (GPIOH_5)
- register 7 bit 22: eth_rxd3 (DIF_2_P)
- register 7 bit 23: eth_rxd2 (DIF_2_N)
Drop the eth_txd0_1 and eth_txd1_1 groups from eth_rgmii_pins to fix the
Ethernet transmit performance on Odroid-C1. Also add the eth_rxd2 and
eth_rxd3 groups so we don't rely on the bootloader to set them up.
iperf3 statistics before this change:
- transmitting from Odroid-C1: 741 Mbits/sec (0 retries)
- receiving on Odroid-C1: 199 Mbits/sec (1713 retries)
iperf3 statistics after this change:
- transmitting from Odroid-C1: 667 Mbits/sec (0 retries)
- receiving on Odroid-C1: 750 Mbits/sec (0 retries)
Fixes: b96446541d8390 ("ARM: dts: meson8b: extend ethernet controller description")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Emiliano Ingrassia <ingrassia@epigenesys.com>
Cc: Linus Lüssing <linus.luessing@c0d3.blue>
Tested-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Reviewed-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The peripheral bus on the i.MX8MQ is still limited to 32bits, so
we need to declare the usable range for device DMA operations, as
the DRAM will extend across the 32bit boundary if more than 3GB
are installed.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add the node for the ARM Performance Monitor Units.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add RTC support for i.MX8MQ.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Tested-by: Chris Spencer <christopher.spencer@sea.co.uk>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable the Freescale/NXP QuadSPI controller with a proper pinctrl set on
the i.MX8MQ EVK board.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add a node for the Freescale/NXP QuadSPI controller and extend the AIPS3
memory range to accommodate the QuadSPI-memory region.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for the three ECSPI ports present on i.MX8MQ.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add the stmpe-adc DT node as found on Toradex iMX6 modules
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
Baolin Wang
Ezequiel Garcia
Enric Balletbo i Serra
Johan Jonker
Andy Gross
Manivannan Sadhasivam
Peter Geis
Akash Gajjar
Robin Murphy
Vignesh R
Roger Quadros
Jyri Sarha
Masahiro Yamada
Kunihiko Hayashi
Andreas Kemnade
Martyn Welch
Sudeep Holla
Adam Ford
Anson Huang
Andrew Lunn
Philipp Zabel
Marco Felsch
Martin Blumenstingl
Lucas Stach
Carlo Caione
Abel Vesa
Fabio Estevam
Philippe Schenker