Age | Commit message (Collapse) | Author | Files | Lines |
|
When MES is enabled KIQ is not available. Return an error
when someone uses the debugfs preempt test interface in
that case.
Acked-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
DCN IPS interoperates with other system idle power features, such as
Zstates.
On DCN35, there is a known issue where system Z8 + DCN IPS2 causes a
hard hang. We observe this on systems where the SBIOS allows Z8.
Though there is a SBIOS fix, there's no guarantee that users will get it
any time soon, or even install it. A workaround is needed to prevent
this from rearing its head in the wild.
[How]
For DCN35, check the pmfw version to determine whether the SBIOS has the
fix. If not, set IPS1+RCG as the deepest possible state in all cases
except for s0ix and display off (DPMS). Otherwise, enable all IPS
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
log message "Dumping IP State Completed" needs to
be logged only once when state dumping is complete.
Hence moving it out of the for loop.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Acked-by: Trigger Huang <Trigger.Huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[background] when unloading amdgpu driver right after running a
workload, drain_workqueue is causing "Fence fallback timer
expired on ring sdma0.0". Under sriov, this issue will cause sriov
full access timeout and a reset happening.
move drain_workqueue before shutdown is set to allow ih process and
before enter full access under sriov to avoid full access time cost.
Signed-off-by: Victor Zhao <Victor.Zhao@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Do the coredump immediately after a job timeout to get a closer
representation of GPU's error status.
V2: This will skip printing vram_lost as the GPU reset is not
happened yet (Alex)
V3: Unconditionally call the core dump as we care about all the reset
functions(soft-recovery and queue reset and full adapter reset, Alex)
V4: Do the dump after adev->job_hang = true (Sunil)
Signed-off-by: Trigger Huang <Trigger.Huang@amd.com>
Acked-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The vm lost status can only be obtained after a GPU reset occurs, but
sometimes a dev core dump can be happened before GPU reset. So a new
argument is added to tell the dev core dump implementation whether to
skip printing the vram_lost status in the dump.
And this patch is also trying to decouple the core dump function from
the GPU reset function, by replacing the argument amdgpu_reset_context
with amdgpu_job to specify the context for core dump.
V2: Inform user if VRAM lost check is skipped so users don't assume
VRAM wasn't lost (Alex)
Signed-off-by: Trigger Huang <Trigger.Huang@amd.com>
Suggested-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Pending extended validation.
Reviewed-and-tested-by: Jiadong Zhu <Jiadong.Zhu@amd.com>
Acked-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add this flag to enable experimental resets for testing before they
are fully validated.
Reviewed-and-tested-by: Jiadong Zhu <Jiadong.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
It is to fix in try_disable_dsc() due to misrevert of
commit 338567d17627 ("drm/amd/display: Fix MST BW calculation Regression")
[How]
Fix restoring minimum compression bw by 'max_kbps', instead of native bw 'stream_kbps'
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Always reprogram the hardware state on init. This ensures
the PMFW state is explicitly programmed and we are not relying
on the default PMFW state.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3131
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Remove unnecessary TODO from spl_os_types.h
Reviewed-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Use appropriate SPDX copyright for spl_os_types.h
Reviewed-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add DSC log in each critical routines to facilitate debugging.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This version brings along the following fixes:
- Fix MS/MP mismatches in dml21 for dcn401
- Resolved Coverity issues
- Add back quality EASF and ISHARP and dc dependency changes
- Add sharpness support for windowed YUV420 video
- Add improvements for text display and HDR DWM and MPO
- Fix Synaptics Cascaded Panamera DSC Determination
- Allocate DCN35 clock table transfer buffers in GART
- Add Replay Low Refresh Rate parameters in dc type
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Previous only applied sharpness for fullscreen YUV420 video.
[How]
Remove fullscrene restriction and apply sharpness for windowed
YUV420 video as well.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Tune settings for improved text display.
Handle differences between DWM and MPO in HDR path.
[How]
Update sharpener LBA table.
Use HDR multiplier to calculate scalar matrix coefficients
for HDR RGB MPO path.
Update unit tests.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Why:
To supported Low Refresh Rate panel for Replay Feature,
Adding some parameters to record Low Refresh Rate information.
Reviewed-by: Robin Chen <robin.chen@amd.com>
Signed-off-by: Dennis Chan <dennis.chan@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Addressed previous issues with quality changes and new issues due to
rolling back quality changes.
[How]
This reverts commit f9e6759888866748f31b6b6c2142a481d587f51f, fixes merge conflicts, and fixed some
formatting errors.
Store current sharpness level for each pregen table to minimize
calculating sharpness table every time.
Disable dynamic ODM when sharpness is enabled.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
We want to avoid arming the HPD timer in firmware when preparing for
S0i3 entry when DC is considered in D3.
[How]
Notify DMCUB of the power state transitions so it can decide to arm
the HPD timer for idle in DCN35 only in D0.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Ovidiu Bunea <Ovidiu.Bunea@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Synaptics Cascaded Panamera topology needs to unconditionally
acquire root aux for dsc decoding.
Reviewed-by: Roman Li <roman.li@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Because sometime DMUB GPINT will time out,
it will cause we return 0 as residency number.
[How]
Retry to avoid this happened.
Reviewed-by: Robin Chen <robin.chen@amd.com>
Signed-off-by: ChunTao Tso <ChunTao.Tso@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Request from PMFW to use GART for clock table transfer tables as
framebuffer is being deprecated on APU.
[How]
Switch over to GART via the allocation flag.
Reviewed-by: Sung joon Kim <sungjoon.kim@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
translate_by_source need not be set for DCN401 onwards since cursor
cursor composition comes after scaler in the hardware pipeline.
Hence offset calculation has been reworked, and this setting is not
necessary to be enabled anymore.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
Remove coverity issues that were originally ignored.
[HOW]
Ran coverity locally on driver, used output report to find existing
coverity issues, resolved them
Reviewed-by: Nicholas Choi <nicholas.choi@amd.com>
Signed-off-by: Daniel Sa <Daniel.Sa@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
Prefetch calculations did not guarantee that bandwidth required in
mode support was less than mode programming which can cause failures.
[HOW]
Fix bandwidth calculations to assume fixed times for OTO schedule,
and choose which schedule to use based on time to fetch pixel data.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Description]
Before every full update we must wait for all pending updates to be
cleared - this is particularly important for minimal transitions
because if we don't wait for pending cleared, it will be as if
there was no minimal transition at all. In OTG we must read 3 different
status registers for pending cleared, one specifically for OTG updates,
one specifically for OPTC updates, and the last for surface related
updates
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
post_divider_value should not be 0.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Ahmed, Muhammad <Ahmed.Ahmed@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Description]
Skipping clock updates is not a hard requirement for overclocking
and only an optimization. Remove the skip as this can cause issues
for FAMS transitions during the overclock sequence. If FAMS
is enabled we must disable UCLK switch on any full update (which
requires update clocks to be called).
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Idle power states (IPS) describe levels of power-gating within DCN. DM
and DC is responsible for ensuring that we are out of IPS before any DCN
programming happens. Any DCN programming while we're in IPS leads to
undefined behavior (mostly hangs).
Because IPS intersects with all display features, the ability to disable
IPS by default while ironing out the known issues is desired. However,
disabing it completely will cause important features such as s0ix entry
to fail.
Therefore, more granular IPS debug flags are desired.
[How]
Extend the dc debug mask bits to include the available list of IPS
debug flags.
All the flags should work as documented, with the exception of
IPS_DISABLE_DYNAMIC. It requires dm changes which will be done in
later changes.
v2: enable docs and fix docstring format
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Print the index for the profiles.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3543
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
No change in functionality for the current code, but we
need to set the index properly before changing it if we
ever use a non-0 index.
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The kernel doc says you need to select manual mode to
adjust this, but the code only allows you to adjust it when
manual mode is not selected. Remove the manual mode check.
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
|
|
rebalance_work was keying off of the presence of rebelance_opts in the
extent - but that was incorrect, we keep those around after rebalance
for indirect extents since the inode's options are not directly
available
Fixes: 20ac515a9cc7 ("bcachefs: bch_acct_rebalance_work")
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
This fixes an apparent deadlock - rebalance would get stuck trying to
take nocow locks because they weren't being released by copygc.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
Drop unsupported features on smu v14_0_2.
Signed-off-by: Candice Li <candice.li@amd.com>
Reviewed-by: Yang Wang <kevinyang.wang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
When app unmap vm ranges(munmap) kfd/svm starts drain pending page fault and
not handle any incoming pages fault of this process until a deferred work item
got executed by default system wq. The time period of "not handle page fault"
can be long and is unpredicable. That is advese to kfd performance on page
faults recovery.
This patch uses time stamp of incoming page fault to decide to drop or recover
page fault. When app unmap vm ranges kfd records each gpu device's ih ring
current time stamp. These time stamps are used at kfd page fault recovery
routine.
Any page fault happened on unmapped ranges after unmap events is application
bug that accesses vm range after unmap. It is not driver work to cover that.
By using time stamp of page fault do not need drain page faults at deferred
work. So, the time period that kfd does not handle page faults is reduced
and can be controlled.
Signed-off-by: Xiaogang.Chen <Xiaogang.Chen@amd.com>
Reviewed-by: Philip Yang <Philip.Yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add p2s table support for a new revision of SMUv13.0.6.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Asad Kamal <asad.kamal@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add gc_info table v1.3 for IP discovery.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Instead of using state->fb->obj[0] directly, get object from framebuffer
by calling drm_gem_fb_get_obj() and return error code when object is
null to avoid using null object of framebuffer.
Fixes: 5d945cbcd4b1 ("drm/amd/display: Create a file dedicated to planes")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add list empty check to avoid null pointer issues in some corner cases.
- list_for_each_entry_safe()
Signed-off-by: Yang Wang <kevinyang.wang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The sparse tool complains as follows:
drivers/gpu/drm/amd/amdgpu/../display/dc/dsc/dcn401/dcn401_dsc.c:30:24: warning:
symbol 'dcn401_dsc_funcs' was not declared. Should it be static?
This symbol is not used outside of dcn401_dsc.c, so marks it static.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The sparse tool complains as follows:
drivers/gpu/drm/amd/amdgpu/../display/dc/hubp/dcn35/dcn35_hubp.c:191:19: warning:
symbol 'dcn35_hubp_funcs' was not declared. Should it be static?
This symbol is not used outside of dcn35_hubp.c, so marks it static.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The sparse tool complains as follows:
drivers/gpu/drm/amd/amdgpu/../display/dc/dml2/dml21/src/dml2_core/dml2_core_dcn4.c:12:28: warning:
symbol 'core_dcn4_ip_caps_base' was not declared. Should it be static?
This symbol is not used outside of dcn35_hubp.c, so marks it static.
And do not want to change it, so mark it const.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The sparse tool complains as follows:
drivers/gpu/drm/amd/amdgpu/../display/dc/dml2/dml21/src/dml2_core/dml2_core_dcn4_calcs.c:6853:56: warning:
symbol 'core_dcn4_g6_temp_read_blackout_table' was not declared. Should it be static?
This symbol is not used outside of dml2_core_dcn4_calcs.c, so marks it static.
And not want to change it, so mark it const.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This needs to be set to 1 to avoid a potential deadlock in
the GC 10.x and newer. On GC 9.x and older, this needs
to be set to 0. This can lead to hangs in some mixed
graphics and compute workloads.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3575
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Driver switches to interrupt source id to identify
utcl2 poison event. polling interface is not needed.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
when trying to enable p2p the amdgpu_device_is_peer_accessible()
checks the condition where address_mask overlaps the aper_base
and hence returns 0, due to which the p2p disables for this platform
IOMMU should remap the BAR addresses so the device can access
them. Hence check if peer_adev is remapping DMA
v5: (Felix, Alex)
- fixing comment as per Alex feedback
- refactor code as per Felix
v4: (Alex)
- fix the comment and description
v3:
- remove iommu_remap variable
v2: (Alex)
- Fix as per review comments
- add new function amdgpu_device_check_iommu_remap to check if iommu
remap
Signed-off-by: Rahul Jain <Rahul.Jain@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
update message interface for smu v14.0.2/3
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Yang Wang <kevinyang.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Not supported.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|