| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The KSZ8795 driver code was modified to use on KSZ8863/73, which has
different register definitions. Some of the new KSZ8795 register
information are wrong compared to previous code.
KSZ8795 also behaves differently in that the STATIC_MAC_TABLE_USE_FID
and STATIC_MAC_TABLE_FID bits are off by 1 when doing MAC table reading
than writing. To compensate that a special code was added to shift the
register value by 1 before applying those bits. This is wrong when the
code is running on KSZ8863, so this special code is only executed when
KSZ8795 is detected.
Fixes: 4b20a07e103f ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If TCA_FLOWER_CLASSID is specified in the netlink message, the code will
call tcf_bind_filter. However, if any error occurs after that, the code
should undo this by calling tcf_unbind_filter.
Fixes: 77b9900ef53a ("tc: introduce Flower classifier")
Signed-off-by: Victor Nogueira <victor@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If cls_bpf_offload errors out, we must also undo tcf_bind_filter that
was done before the error.
Fix that by calling tcf_unbind_filter in errout_parms.
Fixes: eadb41489fd2 ("net: cls_bpf: add support for marking filters as hardware-only")
Signed-off-by: Victor Nogueira <victor@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the case of an update, when TCA_U32_LINK is set, u32_set_parms will
decrement the refcount of the ht_down (struct tc_u_hnode) pointer
present in the older u32 filter which we are replacing. However, if
u32_replace_hw_knode errors out, the update command fails and that
ht_down pointer continues decremented. To fix that, when
u32_replace_hw_knode fails, check if ht_down's refcount was decremented
and undo the decrement.
Fixes: d34e3e181395 ("net: cls_u32: Add support for skip-sw flag to tc u32 classifier.")
Signed-off-by: Victor Nogueira <victor@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When u32_replace_hw_knode fails, we need to undo the tcf_bind_filter
operation done at u32_set_parms.
Fixes: d34e3e181395 ("net: cls_u32: Add support for skip-sw flag to tc u32 classifier.")
Signed-off-by: Victor Nogueira <victor@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case an error occurred after mall_set_parms executed successfully, we
must undo the tcf_bind_filter call it issues.
Fix that by calling tcf_unbind_filter in err_replace_hw_filter label.
Fixes: ec2507d2a306 ("net/sched: cls_matchall: Fix error path")
Signed-off-by: Victor Nogueira <victor@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change an errant kernel-doc comment marker (/**) to a regular
comment to prevent a kernel-doc warning.
rsi_91x.h:3: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Copyright (c) 2017 Redpine Signals Inc.
Fixes: 4c10d56a76bb ("rsi: add header file rsi_91x")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Cc: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230714045127.18752-10-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Spell a struct member's name correctly to prevent a kernel-doc
warning.
pie.h:38: warning: Function parameter or member 'tupdate' not described in 'pie_params'
Fixes: b42a3d7c7cff ("pie: improve comments and commenting style")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Leslie Monis <lesliemonis@gmail.com>
Cc: "Mohit P. Tahiliani" <tahiliani@nitk.edu.in>
Cc: Gautam Ramakrishnan <gautamramk@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Link: https://lore.kernel.org/r/20230714045127.18752-9-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use the struct member's name and the correct format to prevent a
kernel-doc warning.
nsh.h:200: warning: Function parameter or member 'context' not described in 'nsh_md1_ctx'
Fixes: 1f0b7744c505 ("net: add NSH header structures and helpers")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jiri Benc <jbenc@redhat.com>
Link: https://lore.kernel.org/r/20230714045127.18752-8-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use the corrent function parameter name or format to prevent
kernel-doc warnings.
Add 2 function parameter descriptions to prevent kernel-doc warnings.
llc_pdu.h:278: warning: Function parameter or member 'da' not described in 'llc_pdu_decode_da'
llc_pdu.h:278: warning: Excess function parameter 'sa' description in 'llc_pdu_decode_da'
llc_pdu.h:330: warning: Function parameter or member 'skb' not described in 'llc_pdu_init_as_test_cmd'
llc_pdu.h:379: warning: Function parameter or member 'svcs_supported' not described in 'llc_pdu_init_as_xid_cmd'
llc_pdu.h:379: warning: Function parameter or member 'rx_window' not described in 'llc_pdu_init_as_xid_cmd'
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20230714045127.18752-7-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Modify the anonymous enum kernel-doc content so that it doesn't cause
a kernel-doc warning.
inet_frag.h:33: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
Fixes: 1ab1934ed80a ("inet: frags: enum the flag definitions and add descriptions")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230714045127.18752-6-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Spell function or struct member names correctly.
Use ':' instead of '-' for struct member entries.
Mark one field as private in kernel-doc.
Add a few entries that were missing.
Fix a typo.
These changes prevent kernel-doc warnings:
devlink.h:252: warning: Function parameter or member 'field_id' not described in 'devlink_dpipe_match'
devlink.h:267: warning: Function parameter or member 'field_id' not described in 'devlink_dpipe_action'
devlink.h:310: warning: Function parameter or member 'match_values_count' not described in 'devlink_dpipe_entry'
devlink.h:355: warning: Function parameter or member 'list' not described in 'devlink_dpipe_table'
devlink.h:374: warning: Function parameter or member 'actions_dump' not described in 'devlink_dpipe_table_ops'
devlink.h:374: warning: Function parameter or member 'matches_dump' not described in 'devlink_dpipe_table_ops'
devlink.h:374: warning: Function parameter or member 'entries_dump' not described in 'devlink_dpipe_table_ops'
devlink.h:374: warning: Function parameter or member 'counters_set_update' not described in 'devlink_dpipe_table_ops'
devlink.h:374: warning: Function parameter or member 'size_get' not described in 'devlink_dpipe_table_ops'
devlink.h:384: warning: Function parameter or member 'headers' not described in 'devlink_dpipe_headers'
devlink.h:384: warning: Function parameter or member 'headers_count' not described in 'devlink_dpipe_headers'
devlink.h:398: warning: Function parameter or member 'unit' not described in 'devlink_resource_size_params'
devlink.h:487: warning: Function parameter or member 'id' not described in 'devlink_param'
devlink.h:645: warning: Function parameter or member 'overwrite_mask' not described in 'devlink_flash_update_params'
Fixes: 1555d204e743 ("devlink: Support for pipeline debug (dpipe)")
Fixes: d9f9b9a4d05f ("devlink: Add support for resource abstraction")
Fixes: eabaef1896bc ("devlink: Add devlink_param register and unregister")
Fixes: 5d5b4128c4ca ("devlink: introduce flash update overwrite mask")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: Moshe Shemesh <moshe@mellanox.com>
Cc: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20230714045127.18752-5-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use '@' before the struct member names in kernel-doc notation
to prevent kernel-doc warnings.
codel.h:158: warning: Function parameter or member 'ecn_mark' not described in 'codel_stats'
codel.h:158: warning: Function parameter or member 'ce_mark' not described in 'codel_stats'
Fixes: 76e3cc126bb2 ("codel: Controlled Delay AQM")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: Dave Taht <dave.taht@bufferbloat.net>
Link: https://lore.kernel.org/r/20230714045127.18752-4-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add an enum heading to the kernel-doc comments to prevent
kernel-doc warnings.
cfg802154.h:174: warning: Cannot understand * @WPAN_PHY_FLAG_TRANSMIT_POWER: Indicates that transceiver will support
on line 174 - I thought it was a doc line
cfg802154.h:192: warning: Enum value 'WPAN_PHY_FLAG_TXPOWER' not described in enum 'wpan_phy_flags'
cfg802154.h:192: warning: Excess enum value 'WPAN_PHY_FLAG_TRANSMIT_POWER' description in 'wpan_phy_flags'
Fixes: edea8f7c75ec ("cfg802154: introduce wpan phy flags")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Alexander Aring <alex.aring@gmail.com>
Cc: Stefan Schmidt <stefan@datenfreihafen.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230714045127.18752-3-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Change an errant kernel-doc comment marker (/**) to a regular
comment to prevent a kernel-doc warning.
bonding.h:282: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Returns NULL if the net_device does not belong to any of the bond's slaves
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Link: https://lore.kernel.org/r/20230714045127.18752-2-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 1fd54773c267 ("udp: allow header check for dodgy GSO_UDP_L4
packets.") checks DODGY bit for UDP, but for packets that can be fed
directly to the device after gso_segs reset, it actually falls through
to fragmentation:
https://lore.kernel.org/all/CAJPywTKDdjtwkLVUW6LRA2FU912qcDmQOQGt2WaDo28KzYDg+A@mail.gmail.com/
This change restores the expected behavior of GSO_UDP_L4 packets.
Fixes: 1fd54773c267 ("udp: allow header check for dodgy GSO_UDP_L4 packets.")
Suggested-by: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Signed-off-by: Yan Zhai <yan@cloudflare.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Identify issues that arise by using the tests/doublebitand.cocci
semantic patch. Need to remove duplicate expression in if statement.
Signed-off-by: Wang Ming <machel@vivo.com>
Reviewed-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is expected that most callers should _ignore_ the errors return by
debugfs_create_dir() in bnad_debugfs_init().
Signed-off-by: Wang Ming <machel@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the call to of_get_ethdev_address to mtk_add_mac which is part of
the probe function and can hence itself return -EPROBE_DEFER should
of_get_ethdev_address return -EPROBE_DEFER. This allows us to entirely
get rid of the mtk_init function.
The problem of of_get_ethdev_address returning -EPROBE_DEFER surfaced
in situations in which the NVMEM provider holding the MAC address has
not yet be loaded at the time mtk_eth_soc is initially probed. In this
case probing of mtk_eth_soc should be deferred instead of falling back
to use a random MAC address, so once the NVMEM provider becomes
available probing can be repeated.
Fixes: 656e705243fd ("net-next: mediatek: add support for MT7623 ethernet")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we create an L2 loop on a bridge in netns, we will see packets storm
even if STP is enabled.
# unshare -n
# ip link add br0 type bridge
# ip link add veth0 type veth peer name veth1
# ip link set veth0 master br0 up
# ip link set veth1 master br0 up
# ip link set br0 type bridge stp_state 1
# ip link set br0 up
# sleep 30
# ip -s link show br0
2: br0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT group default qlen 1000
link/ether b6:61:98:1c:1c:b5 brd ff:ff:ff:ff:ff:ff
RX: bytes packets errors dropped missed mcast
956553768 12861249 0 0 0 12861249 <-. Keep
TX: bytes packets errors dropped carrier collsns | increasing
1027834 11951 0 0 0 0 <-' rapidly
This is because llc_rcv() drops all packets in non-root netns and BPDU
is dropped.
Let's add extack warning when enabling STP in netns.
# unshare -n
# ip link add br0 type bridge
# ip link set br0 type bridge stp_state 1
Warning: bridge: STP does not work in non-root netns.
Note this commit will be reverted later when we namespacify the whole LLC
infra.
Fixes: e730c15519d0 ("[NET]: Make packet reception network namespace safe")
Suggested-by: Harry Coin <hcoin@quietfountain.com>
Link: https://lore.kernel.org/netdev/0f531295-e289-022d-5add-5ceffa0df9bc@quietfountain.com/
Suggested-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CPSW ALE has 75 bit ALE entries which are stored within three 32 bit words.
The cpsw_ale_get_field() and cpsw_ale_set_field() functions assume that the
field will be strictly contained within one word. However, this is not
guaranteed to be the case and it is possible for ALE field entries to span
across up to two words at the most.
Fix the methods to handle getting/setting fields spanning up to two words.
Fixes: db82173f23c5 ("netdev: driver: ethernet: add cpsw address lookup engine support")
Signed-off-by: Tanmay Patil <t-patil@ti.com>
[s-vadapalli@ti.com: rephrased commit message and added Fixes tag]
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The at9331 is only able to read or write a single register at once. The
driver has a custom regmap bus and chooses to tell the regmap core about
this by reporting the maximum transfer sizes rather than the explicit
flags that exist at the regmap level. Since there are a number of
problems with the raw transfer limits and the regmap level flags are
better integrated anyway convert the driver to use the flags.
No functional change.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The syzbot fuzzer identified a problem in the usbnet driver:
usb 1-1: BOGUS urb xfer, pipe 3 != type 1
WARNING: CPU: 0 PID: 754 at drivers/usb/core/urb.c:504 usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504
Modules linked in:
CPU: 0 PID: 754 Comm: kworker/0:2 Not tainted 6.4.0-rc7-syzkaller-00014-g692b7dc87ca6 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/27/2023
Workqueue: mld mld_ifc_work
RIP: 0010:usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504
Code: 7c 24 18 e8 2c b4 5b fb 48 8b 7c 24 18 e8 42 07 f0 fe 41 89 d8 44 89 e1 4c 89 ea 48 89 c6 48 c7 c7 a0 c9 fc 8a e8 5a 6f 23 fb <0f> 0b e9 58 f8 ff ff e8 fe b3 5b fb 48 81 c5 c0 05 00 00 e9 84 f7
RSP: 0018:ffffc9000463f568 EFLAGS: 00010086
RAX: 0000000000000000 RBX: 0000000000000001 RCX: 0000000000000000
RDX: ffff88801eb28000 RSI: ffffffff814c03b7 RDI: 0000000000000001
RBP: ffff8881443b7190 R08: 0000000000000001 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000000003
R13: ffff88802a77cb18 R14: 0000000000000003 R15: ffff888018262500
FS: 0000000000000000(0000) GS:ffff8880b9800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000556a99c15a18 CR3: 0000000028c71000 CR4: 0000000000350ef0
Call Trace:
<TASK>
usbnet_start_xmit+0xfe5/0x2190 drivers/net/usb/usbnet.c:1453
__netdev_start_xmit include/linux/netdevice.h:4918 [inline]
netdev_start_xmit include/linux/netdevice.h:4932 [inline]
xmit_one net/core/dev.c:3578 [inline]
dev_hard_start_xmit+0x187/0x700 net/core/dev.c:3594
...
This bug is caused by the fact that usbnet trusts the bulk endpoint
addresses its probe routine receives in the driver_info structure, and
it does not check to see that these endpoints actually exist and have
the expected type and directions.
The fix is simply to add such a check.
Reported-and-tested-by: syzbot+63ee658b9a100ffadbe2@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-usb/000000000000a56e9105d0cec021@google.com/
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/ea152b6d-44df-4f8a-95c6-4db51143dcc1@rowland.harvard.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
I get sporadic timeouts from the driver when using the
MV88E6352. Reading the status again after the loop fixes the
problem: the operation is successful but goes undetected.
Some added prints show things like this:
[ 58.356209] mv88e6085 mdio_mux-0.1:00: Timeout while waiting
for switch, addr 1b reg 0b, mask 8000, val 0000, data c000
[ 58.367487] mv88e6085 mdio_mux-0.1:00: Timeout waiting for
ATU op 4000, fid 0001
(...)
[ 61.826293] mv88e6085 mdio_mux-0.1:00: Timeout while waiting
for switch, addr 1c reg 18, mask 8000, val 0000, data 9860
[ 61.837560] mv88e6085 mdio_mux-0.1:00: Timeout waiting
for PHY command 1860 to complete
The reason is probably not the commands: I think those are
mostly fine with the 50+50ms timeout, but the problem
appears when OpenWrt brings up several interfaces in
parallel on a system with 7 populated ports: if one of
them take more than 50 ms and waits one or more of the
others can get stuck on the mutex for the switch and then
this can easily multiply.
As we sleep and wait, the function loop needs a final
check after exiting the loop if we were successful.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Cc: Tobias Waldekranz <tobias@waldekranz.com>
Fixes: 35da1dfd9484 ("net: dsa: mv88e6xxx: Improve performance of busy bit polling")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230712223405.861899-1-linus.walleij@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
kmemleak reports:
unreferenced object 0xffff88814d14e200 (size 256):
comm "cat", pid 336, jiffies 4294871818 (age 779.490s)
hex dump (first 32 bytes):
04 00 01 03 00 00 00 00 08 00 00 00 00 00 00 00 ................
0c d8 c8 9b ff ff ff ff 04 5a ca 9b ff ff ff ff .........Z......
backtrace:
[<ffffffff9bdff18f>] __kmalloc+0x4f/0x140
[<ffffffff9bc9238b>] trace_find_next_entry+0xbb/0x1d0
[<ffffffff9bc9caef>] trace_print_lat_context+0xaf/0x4e0
[<ffffffff9bc94490>] print_trace_line+0x3e0/0x950
[<ffffffff9bc95499>] tracing_read_pipe+0x2d9/0x5a0
[<ffffffff9bf03a43>] vfs_read+0x143/0x520
[<ffffffff9bf04c2d>] ksys_read+0xbd/0x160
[<ffffffff9d0f0edf>] do_syscall_64+0x3f/0x90
[<ffffffff9d2000aa>] entry_SYSCALL_64_after_hwframe+0x6e/0xd8
when reading file 'trace_pipe', 'iter->temp' is allocated or relocated
in trace_find_next_entry() but not freed before 'trace_pipe' is closed.
To fix it, free 'iter->temp' in tracing_release_pipe().
Link: https://lore.kernel.org/linux-trace-kernel/20230713141435.1133021-1-zhengyejian1@huawei.com
Cc: stable@vger.kernel.org
Fixes: ff895103a84ab ("tracing: Save off entry when peeking at next entry")
Signed-off-by: Zheng Yejian <zhengyejian1@huawei.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
A packet with stab overhead greater than QFQ_MAX_LMAX should be dropped
by the QFQ qdisc as it can't handle such lengths.
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Lion says:
-------
In the QFQ scheduler a similar issue to CVE-2023-31436
persists.
Consider the following code in net/sched/sch_qfq.c:
static int qfq_enqueue(struct sk_buff *skb, struct Qdisc *sch,
struct sk_buff **to_free)
{
unsigned int len = qdisc_pkt_len(skb), gso_segs;
// ...
if (unlikely(cl->agg->lmax < len)) {
pr_debug("qfq: increasing maxpkt from %u to %u for class %u",
cl->agg->lmax, len, cl->common.classid);
err = qfq_change_agg(sch, cl, cl->agg->class_weight, len);
if (err) {
cl->qstats.drops++;
return qdisc_drop(skb, sch, to_free);
}
// ...
}
Similarly to CVE-2023-31436, "lmax" is increased without any bounds
checks according to the packet length "len". Usually this would not
impose a problem because packet sizes are naturally limited.
This is however not the actual packet length, rather the
"qdisc_pkt_len(skb)" which might apply size transformations according to
"struct qdisc_size_table" as created by "qdisc_get_stab()" in
net/sched/sch_api.c if the TCA_STAB option was set when modifying the qdisc.
A user may choose virtually any size using such a table.
As a result the same issue as in CVE-2023-31436 can occur, allowing heap
out-of-bounds read / writes in the kmalloc-8192 cache.
-------
We can create the issue with the following commands:
tc qdisc add dev $DEV root handle 1: stab mtu 2048 tsize 512 mpu 0 \
overhead 999999999 linklayer ethernet qfq
tc class add dev $DEV parent 1: classid 1:1 htb rate 6mbit burst 15k
tc filter add dev $DEV parent 1: matchall classid 1:1
ping -I $DEV 1.1.1.2
This is caused by incorrectly assuming that qdisc_pkt_len() returns a
length within the QFQ_MIN_LMAX < len < QFQ_MAX_LMAX.
Fixes: 462dbc9101ac ("pkt_sched: QFQ Plus: fair-queueing service at DRR cost")
Reported-by: Lion <nnamrec@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
QFQ only supports a certain bound of MTU size so make sure
we check for this requirement in the tests.
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
25369891fcef deletes a check for the case where no 'lmax' is
specified which 3037933448f6 previously fixed as 'lmax'
could be set to the device's MTU without any bound checking
for QFQ_LMAX_MIN and QFQ_LMAX_MAX. Therefore, reintroduce the check.
Fixes: 25369891fcef ("net/sched: sch_qfq: refactor parsing of netlink parameters")
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
A recent change to start counting SuperH IRQ #s from 16 breaks support
for the Hitachi HD64461 companion chip.
Move the offchip IRQ base and HD64461 IRQ # by 16 in order to
accommodate for the new virq numbering rules.
Fixes: a8ac2961148e ("sh: Avoid using IRQ0 on SH3 and SH4")
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Link: https://lore.kernel.org/r/20230710233132.69734-1-contact@artur-rojek.eu
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
|
|
Take into account the virq offset when translating cascaded interrupts.
Fixes: a8ac2961148e8c72 ("sh: Avoid using IRQ0 on SH3 and SH4")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Link: https://lore.kernel.org/r/7d0cb246c9f1cd24bb1f637ec5cb67e799a4c3b8.1688908227.git.geert+renesas@glider.be
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
|
|
Take into account the virq offset when translating cascaded IRL
interrupts.
Fixes: a8ac2961148e8c72 ("sh: Avoid using IRQ0 on SH3 and SH4")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Link: https://lore.kernel.org/r/4fcb0d08a2b372431c41e04312742dc9e41e1be4.1688908186.git.geert+renesas@glider.be
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
|
|
When booting rts7751r2dplus_defconfig on QEMU, the system hangs due to
an interrupt storm on IRQ 20. IRQ 20 aka event 0x280 is a cascaded IRL
interrupt, which maps to IRQ_VOYAGER, the interrupt used by the Silicon
Motion SM501 multimedia companion chip. As rts7751r2d_irq_demux() does
not take into account the new virq offset, the interrupt is no longer
translated, leading to an unhandled interrupt.
Fix this by taking into account the virq offset when translating
cascaded IRL interrupts.
Fixes: a8ac2961148e8c72 ("sh: Avoid using IRQ0 on SH3 and SH4")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Closes: https://lore.kernel.org/r/fbfea3ad-d327-4ad5-ac9c-648c7ca3fe1f@roeck-us.net
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/2c99d5df41c40691f6c407b7b6a040d406bc81ac.1688901306.git.geert+renesas@glider.be
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
|
|
Fix ethernet header length field after stripping the mesh header
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/CT5GNZSK28AI.2K6M69OXM9RW5@syracuse/
Fixes: 986e43b19ae9 ("wifi: mac80211: fix receiving A-MSDU frames on mesh interfaces")
Reported-and-tested-by: Nicolas Escande <nico.escande@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20230711115052.68430-1-nbd@nbd.name
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If there is a failure during rtw89_fw_h2c_raw() rtw89_debug_priv_send_h2c
should return negative error code instead of a positive value count.
Fix this bug by returning correct error code.
Fixes: e3ec7017f6a2 ("rtw89: add Realtek 802.11ax driver")
Signed-off-by: Zhang Shurong <zhang_shurong@foxmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://lore.kernel.org/r/tencent_AD09A61BC4DA92AD1EB0790F5C850E544D07@qq.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For some device types like TXGBE_ID_XAUI, *checksum computed in
txgbe_calc_eeprom_checksum() is larger than TXGBE_EEPROM_SUM. Remove the
limit on the size of *checksum.
Fixes: 049fe5365324 ("net: txgbe: Add operations to interact with firmware")
Fixes: 5e2ea7801fac ("net: txgbe: Fix unsigned comparison to zero in txgbe_calc_eeprom_checksum()")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://lore.kernel.org/r/20230711063414.3311-1-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Hist triggers can have referenced variables without having direct
variables fields. This can be the case if referenced variables are added
for trigger actions. In this case the newly added references will not
have field variables. Not taking such referenced variables into
consideration can result in a bug where it would be possible to remove
hist trigger with variables being refenced. This will result in a bug
that is easily reproducable like so
$ cd /sys/kernel/tracing
$ echo 'synthetic_sys_enter char[] comm; long id' >> synthetic_events
$ echo 'hist:keys=common_pid.execname,id.syscall:vals=hitcount:comm=common_pid.execname' >> events/raw_syscalls/sys_enter/trigger
$ echo 'hist:keys=common_pid.execname,id.syscall:onmatch(raw_syscalls.sys_enter).synthetic_sys_enter($comm, id)' >> events/raw_syscalls/sys_enter/trigger
$ echo '!hist:keys=common_pid.execname,id.syscall:vals=hitcount:comm=common_pid.execname' >> events/raw_syscalls/sys_enter/trigger
[ 100.263533] ==================================================================
[ 100.264634] BUG: KASAN: slab-use-after-free in resolve_var_refs+0xc7/0x180
[ 100.265520] Read of size 8 at addr ffff88810375d0f0 by task bash/439
[ 100.266320]
[ 100.266533] CPU: 2 PID: 439 Comm: bash Not tainted 6.5.0-rc1 #4
[ 100.267277] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.0-20220807_005459-localhost 04/01/2014
[ 100.268561] Call Trace:
[ 100.268902] <TASK>
[ 100.269189] dump_stack_lvl+0x4c/0x70
[ 100.269680] print_report+0xc5/0x600
[ 100.270165] ? resolve_var_refs+0xc7/0x180
[ 100.270697] ? kasan_complete_mode_report_info+0x80/0x1f0
[ 100.271389] ? resolve_var_refs+0xc7/0x180
[ 100.271913] kasan_report+0xbd/0x100
[ 100.272380] ? resolve_var_refs+0xc7/0x180
[ 100.272920] __asan_load8+0x71/0xa0
[ 100.273377] resolve_var_refs+0xc7/0x180
[ 100.273888] event_hist_trigger+0x749/0x860
[ 100.274505] ? kasan_save_stack+0x2a/0x50
[ 100.275024] ? kasan_set_track+0x29/0x40
[ 100.275536] ? __pfx_event_hist_trigger+0x10/0x10
[ 100.276138] ? ksys_write+0xd1/0x170
[ 100.276607] ? do_syscall_64+0x3c/0x90
[ 100.277099] ? entry_SYSCALL_64_after_hwframe+0x6e/0xd8
[ 100.277771] ? destroy_hist_data+0x446/0x470
[ 100.278324] ? event_hist_trigger_parse+0xa6c/0x3860
[ 100.278962] ? __pfx_event_hist_trigger_parse+0x10/0x10
[ 100.279627] ? __kasan_check_write+0x18/0x20
[ 100.280177] ? mutex_unlock+0x85/0xd0
[ 100.280660] ? __pfx_mutex_unlock+0x10/0x10
[ 100.281200] ? kfree+0x7b/0x120
[ 100.281619] ? ____kasan_slab_free+0x15d/0x1d0
[ 100.282197] ? event_trigger_write+0xac/0x100
[ 100.282764] ? __kasan_slab_free+0x16/0x20
[ 100.283293] ? __kmem_cache_free+0x153/0x2f0
[ 100.283844] ? sched_mm_cid_remote_clear+0xb1/0x250
[ 100.284550] ? __pfx_sched_mm_cid_remote_clear+0x10/0x10
[ 100.285221] ? event_trigger_write+0xbc/0x100
[ 100.285781] ? __kasan_check_read+0x15/0x20
[ 100.286321] ? __bitmap_weight+0x66/0xa0
[ 100.286833] ? _find_next_bit+0x46/0xe0
[ 100.287334] ? task_mm_cid_work+0x37f/0x450
[ 100.287872] event_triggers_call+0x84/0x150
[ 100.288408] trace_event_buffer_commit+0x339/0x430
[ 100.289073] ? ring_buffer_event_data+0x3f/0x60
[ 100.292189] trace_event_raw_event_sys_enter+0x8b/0xe0
[ 100.295434] syscall_trace_enter.constprop.0+0x18f/0x1b0
[ 100.298653] syscall_enter_from_user_mode+0x32/0x40
[ 100.301808] do_syscall_64+0x1a/0x90
[ 100.304748] entry_SYSCALL_64_after_hwframe+0x6e/0xd8
[ 100.307775] RIP: 0033:0x7f686c75c1cb
[ 100.310617] Code: 73 01 c3 48 8b 0d 65 3c 10 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa b8 21 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 35 3c 10 00 f7 d8 64 89 01 48
[ 100.317847] RSP: 002b:00007ffc60137a38 EFLAGS: 00000246 ORIG_RAX: 0000000000000021
[ 100.321200] RAX: ffffffffffffffda RBX: 000055f566469ea0 RCX: 00007f686c75c1cb
[ 100.324631] RDX: 0000000000000001 RSI: 0000000000000001 RDI: 000000000000000a
[ 100.328104] RBP: 00007ffc60137ac0 R08: 00007f686c818460 R09: 000000000000000a
[ 100.331509] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000009
[ 100.334992] R13: 0000000000000007 R14: 000000000000000a R15: 0000000000000007
[ 100.338381] </TASK>
We hit the bug because when second hist trigger has was created
has_hist_vars() returned false because hist trigger did not have
variables. As a result of that save_hist_vars() was not called to add
the trigger to trace_array->hist_vars. Later on when we attempted to
remove the first histogram find_any_var_ref() failed to detect it is
being used because it did not find the second trigger in hist_vars list.
With this change we wait until trigger actions are created so we can take
into consideration if hist trigger has variable references. Also, now we
check the return value of save_hist_vars() and fail trigger creation if
save_hist_vars() fails.
Link: https://lore.kernel.org/linux-trace-kernel/20230712223021.636335-1-mkhalfella@purestorage.com
Cc: stable@vger.kernel.org
Fixes: 067fe038e70f6 ("tracing: Add variable reference handling to hist triggers")
Signed-off-by: Mohamed Khalfella <mkhalfella@purestorage.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
Eric Dumazet says[1]:
-------
Speaking of psched_mtu(), I see that net/sched/sch_pie.c is using it
without holding RTNL, so dev->mtu can be changed underneath.
KCSAN could issue a warning.
-------
Annotate dev->mtu with READ_ONCE() so KCSAN don't issue a warning.
[1] https://lore.kernel.org/all/CANn89iJoJO5VtaJ-2=_d2aOQhb0Xw8iBT_Cxqp2HyuS-zj6azw@mail.gmail.com/
v1 -> v2: Fix commit message
Fixes: d4b36210c2e6 ("net: pkt_sched: PIE AQM scheme")
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230711021634.561598-1-pctammela@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ENA adapters on our instances occasionally reset. Once recently
logged a UBSAN failure to console in the process:
UBSAN: shift-out-of-bounds in build/linux/drivers/net/ethernet/amazon/ena/ena_com.c:540:13
shift exponent 32 is too large for 32-bit type 'unsigned int'
CPU: 28 PID: 70012 Comm: kworker/u72:2 Kdump: loaded not tainted 5.15.117
Hardware name: Amazon EC2 c5d.9xlarge/, BIOS 1.0 10/16/2017
Workqueue: ena ena_fw_reset_device [ena]
Call Trace:
<TASK>
dump_stack_lvl+0x4a/0x63
dump_stack+0x10/0x16
ubsan_epilogue+0x9/0x36
__ubsan_handle_shift_out_of_bounds.cold+0x61/0x10e
? __const_udelay+0x43/0x50
ena_delay_exponential_backoff_us.cold+0x16/0x1e [ena]
wait_for_reset_state+0x54/0xa0 [ena]
ena_com_dev_reset+0xc8/0x110 [ena]
ena_down+0x3fe/0x480 [ena]
ena_destroy_device+0xeb/0xf0 [ena]
ena_fw_reset_device+0x30/0x50 [ena]
process_one_work+0x22b/0x3d0
worker_thread+0x4d/0x3f0
? process_one_work+0x3d0/0x3d0
kthread+0x12a/0x150
? set_kthread_struct+0x50/0x50
ret_from_fork+0x22/0x30
</TASK>
Apparently, the reset delays are getting so large they can trigger a
UBSAN panic.
Looking at the code, the current timeout is capped at 5000us. Using a
base value of 100us, the current code will overflow after (1<<29). Even
at values before 32, this function wraps around, perhaps
unintentionally.
Cap the value of the exponent used for this backoff at (1<<16) which is
larger than currently necessary, but large enough to support bigger
values in the future.
Cc: stable@vger.kernel.org
Fixes: 4bb7f4cf60e3 ("net: ena: reduce driver load time")
Signed-off-by: Krister Johansen <kjlx@templeofstupid.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Shay Agroskin <shayagr@amazon.com>
Link: https://lore.kernel.org/r/20230711013621.GE1926@templeofstupid.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The stack_trace event is an event created by the tracing subsystem to
store stack traces. It originally just contained a hard coded array of 8
words to hold the stack, and a "size" to know how many entries are there.
This is exported to user space as:
name: kernel_stack
ID: 4
format:
field:unsigned short common_type; offset:0; size:2; signed:0;
field:unsigned char common_flags; offset:2; size:1; signed:0;
field:unsigned char common_preempt_count; offset:3; size:1; signed:0;
field:int common_pid; offset:4; size:4; signed:1;
field:int size; offset:8; size:4; signed:1;
field:unsigned long caller[8]; offset:16; size:64; signed:0;
print fmt: "\t=> %ps\n\t=> %ps\n\t=> %ps\n" "\t=> %ps\n\t=> %ps\n\t=> %ps\n" "\t=> %ps\n\t=> %ps\n",i
(void *)REC->caller[0], (void *)REC->caller[1], (void *)REC->caller[2],
(void *)REC->caller[3], (void *)REC->caller[4], (void *)REC->caller[5],
(void *)REC->caller[6], (void *)REC->caller[7]
Where the user space tracers could parse the stack. The library was
updated for this specific event to only look at the size, and not the
array. But some older users still look at the array (note, the older code
still checks to make sure the array fits inside the event that it read.
That is, if only 4 words were saved, the parser would not read the fifth
word because it will see that it was outside of the event size).
This event was changed a while ago to be more dynamic, and would save a
full stack even if it was greater than 8 words. It does this by simply
allocating more ring buffer to hold the extra words. Then it copies in the
stack via:
memcpy(&entry->caller, fstack->calls, size);
As the entry is struct stack_entry, that is created by a macro to both
create the structure and export this to user space, it still had the caller
field of entry defined as: unsigned long caller[8].
When the stack is greater than 8, the FORTIFY_SOURCE code notices that the
amount being copied is greater than the source array and complains about
it. It has no idea that the source is pointing to the ring buffer with the
required allocation.
To hide this from the FORTIFY_SOURCE logic, pointer arithmetic is used:
ptr = ring_buffer_event_data(event);
entry = ptr;
ptr += offsetof(typeof(*entry), caller);
memcpy(ptr, fstack->calls, size);
Link: https://lore.kernel.org/all/20230612160748.4082850-1-svens@linux.ibm.com/
Link: https://lore.kernel.org/linux-trace-kernel/20230712105235.5fc441aa@gandalf.local.home
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Reported-by: Sven Schnelle <svens@linux.ibm.com>
Tested-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
As comments in ftrace_process_locs(), there may be NULL pointers in
mcount_loc section:
> Some architecture linkers will pad between
> the different mcount_loc sections of different
> object files to satisfy alignments.
> Skip any NULL pointers.
After commit 20e5227e9f55 ("ftrace: allow NULL pointers in mcount_loc"),
NULL pointers will be accounted when allocating ftrace pages but skipped
before adding into ftrace pages, this may result in some pages not being
used. Then after commit 706c81f87f84 ("ftrace: Remove extra helper
functions"), warning may occur at:
WARN_ON(pg->next);
To fix it, only warn for case that no pointers skipped but pages not used
up, then free those unused pages after releasing ftrace_lock.
Link: https://lore.kernel.org/linux-trace-kernel/20230712060452.3175675-1-zhengyejian1@huawei.com
Cc: stable@vger.kernel.org
Fixes: 706c81f87f84 ("ftrace: Remove extra helper functions")
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Zheng Yejian <zhengyejian1@huawei.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
The simple_write_to_buffer() function is designed to handle partial
writes. It returns negatives on error, otherwise it returns the number
of bytes that were able to be copied. This code doesn't check the
return properly. We only know that the first byte is written, the rest
of the buffer might be uninitialized.
There is no need to use the simple_write_to_buffer() function.
Partial writes are prohibited by the "if (*ppos != 0)" check at the
start of the function. Just use memdup_user() and copy the whole
buffer.
Fixes: d3cbb907ae57 ("netdevsim: add ACL trap reporting cookie as a metadata")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/7c1f950b-3a7d-4252-82a6-876e53078ef7@moroto.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Soft lockup occurs when reading file 'trace_pipe':
watchdog: BUG: soft lockup - CPU#6 stuck for 22s! [cat:4488]
[...]
RIP: 0010:ring_buffer_empty_cpu+0xed/0x170
RSP: 0018:ffff88810dd6fc48 EFLAGS: 00000246
RAX: 0000000000000000 RBX: 0000000000000246 RCX: ffffffff93d1aaeb
RDX: ffff88810a280040 RSI: 0000000000000008 RDI: ffff88811164b218
RBP: ffff88811164b218 R08: 0000000000000000 R09: ffff88815156600f
R10: ffffed102a2acc01 R11: 0000000000000001 R12: 0000000051651901
R13: 0000000000000000 R14: ffff888115e49500 R15: 0000000000000000
[...]
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f8d853c2000 CR3: 000000010dcd8000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
__find_next_entry+0x1a8/0x4b0
? peek_next_entry+0x250/0x250
? down_write+0xa5/0x120
? down_write_killable+0x130/0x130
trace_find_next_entry_inc+0x3b/0x1d0
tracing_read_pipe+0x423/0xae0
? tracing_splice_read_pipe+0xcb0/0xcb0
vfs_read+0x16b/0x490
ksys_read+0x105/0x210
? __ia32_sys_pwrite64+0x200/0x200
? switch_fpu_return+0x108/0x220
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x61/0xc6
Through the vmcore, I found it's because in tracing_read_pipe(),
ring_buffer_empty_cpu() found some buffer is not empty but then it
cannot read anything due to "rb_num_of_entries() == 0" always true,
Then it infinitely loop the procedure due to user buffer not been
filled, see following code path:
tracing_read_pipe() {
... ...
waitagain:
tracing_wait_pipe() // 1. find non-empty buffer here
trace_find_next_entry_inc() // 2. loop here try to find an entry
__find_next_entry()
ring_buffer_empty_cpu(); // 3. find non-empty buffer
peek_next_entry() // 4. but peek always return NULL
ring_buffer_peek()
rb_buffer_peek()
rb_get_reader_page()
// 5. because rb_num_of_entries() == 0 always true here
// then return NULL
// 6. user buffer not been filled so goto 'waitgain'
// and eventually leads to an deadloop in kernel!!!
}
By some analyzing, I found that when resetting ringbuffer, the 'entries'
of its pages are not all cleared (see rb_reset_cpu()). Then when reducing
the ringbuffer, and if some reduced pages exist dirty 'entries' data, they
will be added into 'cpu_buffer->overrun' (see rb_remove_pages()), which
cause wrong 'overrun' count and eventually cause the deadloop issue.
To fix it, we need to clear every pages in rb_reset_cpu().
Link: https://lore.kernel.org/linux-trace-kernel/20230708225144.3785600-1-zhengyejian1@huawei.com
Cc: stable@vger.kernel.org
Fixes: a5fb833172eca ("ring-buffer: Fix uninitialized read_stamp")
Signed-off-by: Zheng Yejian <zhengyejian1@huawei.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
These are all tracing W=1 warnings in arm64 allmodconfig about missing
prototypes:
kernel/trace/trace_kprobe_selftest.c:7:5: error: no previous prototype for 'kprobe_trace_selftest_target' [-Werror=missing-pro
totypes]
kernel/trace/ftrace.c:329:5: error: no previous prototype for '__register_ftrace_function' [-Werror=missing-prototypes]
kernel/trace/ftrace.c:372:5: error: no previous prototype for '__unregister_ftrace_function' [-Werror=missing-prototypes]
kernel/trace/ftrace.c:4130:15: error: no previous prototype for 'arch_ftrace_match_adjust' [-Werror=missing-prototypes]
kernel/trace/fgraph.c:243:15: error: no previous prototype for 'ftrace_return_to_handler' [-Werror=missing-prototypes]
kernel/trace/fgraph.c:358:6: error: no previous prototype for 'ftrace_graph_sleep_time_control' [-Werror=missing-prototypes]
arch/arm64/kernel/ftrace.c:460:6: error: no previous prototype for 'prepare_ftrace_return' [-Werror=missing-prototypes]
arch/arm64/kernel/ptrace.c:2172:5: error: no previous prototype for 'syscall_trace_enter' [-Werror=missing-prototypes]
arch/arm64/kernel/ptrace.c:2195:6: error: no previous prototype for 'syscall_trace_exit' [-Werror=missing-prototypes]
Move the declarations to an appropriate header where they can be seen
by the caller and callee, and make sure the headers are included where
needed.
Link: https://lore.kernel.org/linux-trace-kernel/20230517125215.930689-1-arnd@kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Florent Revest <revest@chromium.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
[ Fixed ftrace_return_to_handler() to handle CONFIG_HAVE_FUNCTION_GRAPH_RETVAL case ]
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
The self tests for user_events currently does not ensure that the edge
case for struct types work properly with size differences.
Add cases for mis-matching struct names and sizes to ensure they work
properly.
Link: https://lkml.kernel.org/r/20230629235049.581-3-beaub@linux.microsoft.com
Cc: Shuah Khan <skhan@linuxfoundation.org>
Cc: linux-kselftest@vger.kernel.org
Signed-off-by: Beau Belgrave <beaub@linux.microsoft.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
The kernel does not currently validate that both the minimum and maximum
ports of a port range are specified. This can lead user space to think
that a filter matching on a port range was successfully added, when in
fact it was not. For example, with a patched (buggy) iproute2 that only
sends the minimum port, the following commands do not return an error:
# tc filter add dev swp1 ingress pref 1 proto ip flower ip_proto udp src_port 100-200 action pass
# tc filter add dev swp1 ingress pref 1 proto ip flower ip_proto udp dst_port 100-200 action pass
# tc filter show dev swp1 ingress
filter protocol ip pref 1 flower chain 0
filter protocol ip pref 1 flower chain 0 handle 0x1
eth_type ipv4
ip_proto udp
not_in_hw
action order 1: gact action pass
random type none pass val 0
index 1 ref 1 bind 1
filter protocol ip pref 1 flower chain 0 handle 0x2
eth_type ipv4
ip_proto udp
not_in_hw
action order 1: gact action pass
random type none pass val 0
index 2 ref 1 bind 1
Fix by returning an error unless both ports are specified:
# tc filter add dev swp1 ingress pref 1 proto ip flower ip_proto udp src_port 100-200 action pass
Error: Both min and max source ports must be specified.
We have an error talking to the kernel
# tc filter add dev swp1 ingress pref 1 proto ip flower ip_proto udp dst_port 100-200 action pass
Error: Both min and max destination ports must be specified.
We have an error talking to the kernel
Fixes: 5c72299fba9d ("net: sched: cls_flower: Classify packets using port ranges")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
linux-arm-msm is the list most people subscribe to in order to receive
updates about Qualcomm related drivers. Make sure changes for the
Qualcomm ethernet driver make it there.
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20230710195240.197047-1-ahalaney@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the status page from vger to the same server as mailbot.
Link: https://lore.kernel.org/r/20230710174636.1174684-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This is equivalent to 'gen2', and it was always confusing to have
two identical config entries. The split config patch actually had
been originally developed after removing 'use_tfh" and didn't add
the use_tfh in the new configs as they'd later been copied to the
new files. Thus the easiest way to fix the init crash here now is
to just remove use_tfh (which is erroneously unset in most of the
configs now) and use 'gen2' in the code instead.
There's possibly still an unwind error in iwl_txq_gen2_init() as
it crashes if TXQ 0 fails to initialize, but we can deal with it
later since the original failure is due to the use_tfh confusion.
Tested-by: Xi Ruoyao <xry111@xry111.site>
Reported-and-tested-by: Niklāvs Koļesņikovs <pinkflames.linux@gmail.com>
Reported-and-tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Reported-and-tested-by: Zhang Rui <rui.zhang@intel.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217622
Link: https://lore.kernel.org/all/9274d9bd3d080a457649ff5addcc1726f08ef5b2.camel@xry111.site/
Link: https://lore.kernel.org/all/CAAJw_Zug6VCS5ZqTWaFSr9sd85k%3DtyPm9DEE%2BmV%3DAKoECZM%2BsQ@mail.gmail.com/
Fixes: 19898ce9cf8a ("wifi: iwlwifi: split 22000.c into multiple files")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20230710145038.84186-2-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, verifier does not reject XDP programs that pass NULL pointer to
hints functions. At the same time, this case is not handled in any driver
implementation (including veth). For example, changing
bpf_xdp_metadata_rx_timestamp(ctx, ×tamp);
to
bpf_xdp_metadata_rx_timestamp(ctx, NULL);
in xdp_metadata test successfully crashes the system.
Add KF_TRUSTED_ARGS flag to hints kfunc definitions, so driver code
does not have to worry about getting invalid pointers.
Fixes: 3d76a4d3d4e5 ("bpf: XDP metadata RX kfuncs")
Reported-by: Stanislav Fomichev <sdf@google.com>
Closes: https://lore.kernel.org/bpf/ZKWo0BbpLfkZHbyE@google.com/
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Acked-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/r/20230711105930.29170-1-larysa.zaremba@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
Tristram Ha
Victor Nogueira
Randy Dunlap
Yan Zhai
Wang Ming
Daniel Golle
Kuniyuki Iwashima
Tanmay Patil
Mark Brown
Alan Stern
Linus Walleij
Zheng Yejian
Pedro Tammela
Artur Rojek
Geert Uytterhoeven
Felix Fietkau
Zhang Shurong
Jiawen Wu
Mohamed Khalfella
Krister Johansen
Steven Rostedt (Google)
Dan Carpenter
Arnd Bergmann
Beau Belgrave
Ido Schimmel
Andrew Halaney
Jakub Kicinski
Johannes Berg
Larysa Zaremba