| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The DesignWare core requires the receive clock to be running during
certain operations. Ensure that we block PHY RXC clock-stop during
these operations.
This is a best-efforts change - not everywhere can be covered by this
because of net's core locking, which means we can't access the MDIO
bus to configure the PHY to disable RXC clock-stop in certain areas.
These are marked with FIXME comments.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tvO6p-008Vjz-Qy@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some MACs require the PHY receive clock to be running to complete setup
actions. This may fail if the PHY has negotiated EEE, the MAC supports
receive clock stop, and the link has entered LPI state. Provide a pair
of APIs that MAC drivers can use to temporarily block the PHY disabling
the receive clock.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tvO6k-008Vjt-MZ@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As the previous commit addressed DWGMAC resuming with a PHY in
suspended state, there is now no need for socfpga to work around
this. Remove this code.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tvO6f-008Vjn-J1@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The Synopsys Designware GMAC core databook requires all clocks to be
active in order to complete software reset, which we perform during
resume.
However, IEEE 802.3 allows a PHY to stop its clocks when placed in
low-power mode, which happens when the system is suspended and WoL
is not enabled.
As an attempt to work around this, commit 36d18b5664ef ("net: stmmac:
start phylink instance before stmmac_hw_setup()") started phylink
early, but this has the side effect that the mac_link_up() method may
be called before or during the initialisation of GMAC hardware.
We also have the socfpga glue driver directly calling phy_resume()
also as an attempt to work around this.
In a previous commit, phylink_prepare_resume() has been introduced
to give MAC drivers a way to ensure that the PHY is resumed prior to
their initialisation of their MAC hardware. This commit adds the call,
and moves the phylink_resume() call back to where it should be before
the aforementioned commit.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tvO6a-008Vjh-FG@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the system is suspended, the PHY may be placed in low-power mode
by setting the BMCR 0.11 Power down bit. IEEE 802.3 states that the
behaviour of the PHY in this state is implementation specific, and
the PHY is not required to meet the RX_CLK and TX_CLK requirements.
Essentially, this means that a PHY may stop the clocks that it is
generating while in power down state.
However, MACs exist which require the clocks from the PHY to be running
in order to properly resume. phylink_prepare_resume() provides them
with a way to clear the Power down bit early.
Note, however, that IEEE 802.3 gives PHYs up to 500ms grace before the
transmit and receive clocks meet the requirements after clearing the
power down bit.
Add a resume preparation function, which will ensure that the receive
clock from the PHY is appropriately configured while resuming.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tvO6V-008Vjb-AP@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Unlike X2 and EF100, we do not attempt to parse the firmware file to
find an image within it; we simply hand the entire file to the MC,
which is responsible for understanding any container formats we might
use and validating that the firmware file is applicable to this NIC.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://patch.msgid.link/9a72a74002a7819c780b0a18ce9294c9d4e1db12.1742493017.git.ecree.xilinx@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://patch.msgid.link/bcb7597460a5a99d1dca4ef282f4aa2dd46ae545.1742493017.git.ecree.xilinx@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Unlike Siena, no EF10 board ever had an external PHY, and consequently
MDIO handling isn't even built into the firmware. Since Siena has
been split out into its own driver, the MDIO code can be deleted from
the sfc driver.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://patch.msgid.link/aa689d192ddaef7abe82709316c2be648a7bd66e.1742493017.git.ecree.xilinx@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 14a196807482 ("net: reorganize IP MIB values") changed
MIB values to group hot fields together.
Since then 5 new fields have been added without caring about
data locality.
This patch moves IPSTATS_MIB_OUTPKTS, IPSTATS_MIB_NOECTPKTS,
IPSTATS_MIB_ECT1PKTS, IPSTATS_MIB_ECT0PKTS, IPSTATS_MIB_CEPKTS
to the hot portion of per-cpu data.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250320101434.3174412-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
TCP uses generic skb_set_owner_r() and sock_rfree()
for received packets, with socket lock being owned.
Switch to private versions, avoiding two atomic operations
per packet.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20250320121604.3342831-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In rtm_del_nexthop(), only nexthop_find_by_id() and remove_nexthop()
require RTNL as they touch net->nexthop.rb_root.
Let's move RTNL down as rtnl_net_lock() before nexthop_find_by_id().
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/20250319230743.65267-8-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If we pass false to the rtnl_held param of lwtunnel_valid_encap_type(),
we can move RTNL down before rtm_to_nh_config_rtnl().
Let's use rtnl_net_lock() in rtm_new_nexthop().
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/20250319230743.65267-7-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The number of NHA_GROUP entries is guaranteed to be non-zero in
nh_check_attr_group().
Let's remove the redundant check in nexthop_create_group().
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/20250319230743.65267-6-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
nexthop_add() checks if NLM_F_REPLACE is specified without
non-zero NHA_ID, which does not require RTNL.
Let's move the check to rtm_new_nexthop().
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/20250319230743.65267-5-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
NHA_OIF needs to look up a device by __dev_get_by_index(),
which requires RTNL.
Let's move NHA_OIF validation to rtm_to_nh_config_rtnl().
Note that the proceeding checks made the original !cfg->nh_fdb
check redundant.
NHA_FDB is set -> NHA_OIF cannot be set
NHA_FDB is set but false -> NHA_OIF must be set
NHA_FDB is not set -> NHA_OIF must be set
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/20250319230743.65267-4-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We will push RTNL down to rtm_new_nexthop(), and then we
want to move non-RTNL operations out of the scope.
nh_check_attr_group() validates NHA_GROUP attributes, and
nexthop_find_by_id() and some validation requires RTNL.
Let's factorise such parts as nh_check_attr_group_rtnl()
and call it from rtm_to_nh_config_rtnl().
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/20250319230743.65267-3-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We will split rtm_to_nh_config() into non-RTNL and RTNL parts,
and then the latter also needs tb.
As a prep, let's move nlmsg_parse() to rtm_new_nexthop().
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250319230743.65267-2-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ip6_rcv_core() is using:
__IP6_ADD_STATS(net, idev,
IPSTATS_MIB_NOECTPKTS +
(ipv6_get_dsfield(hdr) & INET_ECN_MASK),
max_t(unsigned short, 1, skb_shinfo(skb)->gso_segs));
This is currently evaluating both expressions twice.
Fix _DEVADD() and _DEVUPD() macros to evaluate their arguments once.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250319212516.2385451-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For CT action with commit argument, it's usually followed by the
forward action, either to the output netdev or next chain. The default
behavior for software is to drop by setting action attribute to
TC_ACT_SHOT instead of TC_ACT_PIPE if it's the last action. But driver
can't handle it, so block the offload for such case.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1742392983-153050-6-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In nic mode CT setup where we do hairpin between the two
nics, both nics register to the same flow table (per zone),
and try to offload all rules on it.
Instead, filter the rules that originated from the relevant nic
(so only one side is offloaded for each nic).
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Jianbo Liu <jianbol@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1742392983-153050-5-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Align mlx5 driver usage of 'pfnum' with the documentation clarification
introduced in commit bb70b0d48d8e ("devlink: Improve the port attributes
description").
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1742392983-153050-4-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, mlx5_is_reset_now_capable() checks whether the pci bridge is
accessible only on bridge hot plug capability check. If the pci bridge
is not accessible, reset now will fail regardless of bridge hotplug
capability. Move this check to function mlx5_is_reset_now_capable()
which, in such case, aborts the reset and does so in the request phase
instead of the reset now phase.
Signed-off-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Amir Tzin <amirtz@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1742392983-153050-3-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As queue affinity is being deprecated and will no longer be supported
in the future, Always check for the presence of the port selection
namespace. When available, leverage it to distribute traffic
across the physical ports via steering, ensuring compatibility with
future NICs.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1742392983-153050-2-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For simplicity reasons, the driver avoids crossing work queue fragment
boundaries within the same TX WQE (Work-Queue Element). Until today, as
the number of packets in a TX MPWQE (Multi-Packet WQE) descriptor is not
known in advance, the driver pre-prepared contiguous memory for the
largest possible WQE. For this, when getting too close to the fragment
edge, having no room for the largest WQE possible, the driver was
filling the fragment remainder with NOP descriptors, aligning the next
descriptor to the beginning of the next fragment.
Generating and handling these NOPs wastes resources, like: CPU cycles,
work-queue entries fetched to the device, and PCI bandwidth.
In this patch, we replace this NOPs filling mechanism in the TX MPWQE
flow. Instead, we utilize the remaining entries of the fragment with a
TX MPWQE. If this room turns out to be too small, we simply open an
additional descriptor starting at the beginning of the next fragment.
Performance benchmark:
uperf test, single server against 3 clients.
TCP multi-stream, bidir, traffic profile "2x350B read, 1400B write".
Bottleneck is in inbound PCI bandwidth (device POV).
+---------------+------------+------------+--------+
| | Before | After | |
+---------------+------------+------------+--------+
| BW | 117.4 Gbps | 121.1 Gbps | +3.1% |
+---------------+------------+------------+--------+
| tx_packets | 15 M/sec | 15.5 M/sec | +3.3% |
+---------------+------------+------------+--------+
| tx_nops | 3 M/sec | 0 | -100% |
+---------------+------------+------------+--------+
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/1742391746-118647-1-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Executing dql_reset after setting a non-zero value for limit_min can
lead to an unreasonable situation where dql->limit is less than
dql->limit_min.
For instance, after setting
/sys/class/net/eth*/queues/tx-0/byte_queue_limits/limit_min,
an ifconfig down/up operation might cause the ethernet driver to call
netdev_tx_reset_queue, which in turn invokes dql_reset.
In this case, dql->limit is reset to 0 while dql->limit_min remains
non-zero value, which is unexpected. The limit should always be
greater than or equal to limit_min.
Signed-off-by: Jing Su <jingsusu@didiglobal.com>
Link: https://patch.msgid.link/Z9qHD1s/NEuQBdgH@pilot-ThinkCentre-M930t-N000
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It's always TEST_TIMEOUT_SEC, with an unjustified exception in rst test,
that is more paranoia-long timeout rather than based on requirements.
Signed-off-by: Dmitry Safonov <0x7f454c46@gmail.com>
Link: https://patch.msgid.link/20250319-tcp-ao-selftests-polling-v2-7-da48040153d1@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Unused: it's always either the default timeout or asynchronous
connect().
Signed-off-by: Dmitry Safonov <0x7f454c46@gmail.com>
Link: https://patch.msgid.link/20250319-tcp-ao-selftests-polling-v2-6-da48040153d1@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As both client and server print the same test name on failure or pass,
add "[server]" so that it's more obvious from a log which side printed
"ok" or "not ok".
Signed-off-by: Dmitry Safonov <0x7f454c46@gmail.com>
Link: https://patch.msgid.link/20250319-tcp-ao-selftests-polling-v2-5-da48040153d1@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, tcp_ao tests have two timeouts: TEST_RETRANSMIT_SEC and
TEST_TIMEOUT_SEC [by default 1 and 5 seconds]. The first one,
TEST_RETRANSMIT_SEC is used for operations that are expected to succeed
in order for a test to pass. It is usually not consumed and exists only
to avoid indefinite test run if the operation didn't complete.
The second one, TEST_RETRANSMIT_SEC exists for the tests that checking
operations, that are expected to fail/timeout. It is shorter as it is
fully consumed, with an expectation that if operation didn't succeed
during that period, it will timeout. And the related test that expects
the timeout is passing. The actual operation failure is then
cross-verified by other means like counters checks.
The issue with TEST_RETRANSMIT_SEC timeout is that 1 second is the exact
initial TCP timeout. So, in case the initial segment gets lost (quite
unlikely on local veth interface between two net namespaces, yet happens
in slow VMs), the retransmission never happens and as a result, the test
is not actually testing the functionality. Which in the end fails
counters checks.
As I want tcp_ao selftests to be fast and finishing in a reasonable
amount of time on manual run, I didn't consider increasing
TEST_RETRANSMIT_SEC.
Rather, initially, BPF_SOCK_OPS_TIMEOUT_INIT looked promising as a lever
to make the initial TCP timeout shorter. But as it's not a socket bpf
attached thing, but sock_ops (attaches to cgroups), the selftests would
have to use libbpf, which I wanted to avoid if not absolutely required.
Instead, use a mixed select() and counters polling mode with the longer
TEST_TIMEOUT_SEC timeout to detect running-away failed tests. It
actually not only allows losing segments and succeeding after
the previous TEST_RETRANSMIT_SEC timeout was consumed, but makes
the tests expecting timeout/failure pass faster.
The only test case taking longer (TEST_TIMEOUT_SEC) now is connect-deny
"wrong snd id", which checks for no key on SYN-ACK for which there is no
counter in the kernel (see tcp_make_synack()). Yet it can be speed up
by poking skpair from the trace event (see trace_tcp_ao_synack_no_key).
Fixes: ed9d09b309b1 ("selftests/net: Add a test for TCP-AO keys matching")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Closes: https://lore.kernel.org/netdev/20241205070656.6ef344d7@kernel.org/
Signed-off-by: Dmitry Safonov <0x7f454c46@gmail.com>
Link: https://patch.msgid.link/20250319-tcp-ao-selftests-polling-v2-4-da48040153d1@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There are related TCP-MD5 <=> TCP and TCP-MD5 <=> TCP-AO tests
that can benefit from checking the related counters, not only from
validating operations timeouts.
It also prepares the code for introduction of mixed select()+poll mode,
see the follow-up patches.
Signed-off-by: Dmitry Safonov <0x7f454c46@gmail.com>
Link: https://patch.msgid.link/20250319-tcp-ao-selftests-polling-v2-3-da48040153d1@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Rename __test_tcp_ao_counters_cmp() into test_assert_counters_ao() and
test_tcp_ao_key_counters_cmp() into test_assert_counters_key() as they
are asserts, rather than just compare functions.
Provide test_cmp_counters() helper, that's going to be used to compare
ao_info and netns counters as a stop condition for polling the sockets.
Signed-off-by: Dmitry Safonov <0x7f454c46@gmail.com>
Link: https://patch.msgid.link/20250319-tcp-ao-selftests-polling-v2-2-da48040153d1@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Before:
># 13145[lib/ftrace-tcp.c:427] trace event filter tcp_ao_key_not_found [2001:db8:1::1:-1 => 2001:db8:254::1:7010, L3index 0, flags: !FS!R!P!., keyid: 100, rnext: 100, maclen: -1, sne: -1] = 1
After:
># 13487[lib/ftrace-tcp.c:427] trace event filter tcp_ao_key_not_found [2001:db8:1::1:-1 => 2001:db8:254::1:7010, L3index 0, flags: S, keyid: 100, rnext: 100, maclen: -1, sne: -1] = 1
For the history, I think the initial format was to emphasize the absence
of flags as well as their presence (!R meant no RST flag). But looking
again, it's just unreadable and hard to understand.
Make it the standard/expected one.
Signed-off-by: Dmitry Safonov <0x7f454c46@gmail.com>
Link: https://patch.msgid.link/20250319-tcp-ao-selftests-polling-v2-1-da48040153d1@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a missing attribute of board serial number.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Link: https://patch.msgid.link/20250320085947.103419-2-jiri@resnulli.us
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Set metadata size building the skb from xdp_buff in cpsw/cpsw_new
drivers. ti cpsw and cpsw_new drivers set xdp headroom at least to
CPSW_HEADROOM_NA:
CPSW_HEADROOM_NA max(XDP_PACKET_HEADROOM, NET_SKB_PAD) + NET_IP_ALIGN
so the headroom is large enough to contain xdp_frame and xdp metadata.
Please note this patch is just compiled tested.
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250318-mvneta-xdp-meta-v2-7-b6075778f61f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Set metadata size building the skb from xdp_buff in mana driver.
mana driver sets xdp headroom to XDP_PACKET_HEADROOM so the headroom is
large enough to contain xdp_frame and xdp metadata.
Please note this patch is just compiled tested.
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250318-mvneta-xdp-meta-v2-6-b6075778f61f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Set metadata size building the skb from xdp_buff in mediatek driver.
mtk_eth_soc driver sets xdp headroom to XDP_PACKET_HEADROOM so the
headroom is large enough to contain xdp_frame and xdp metadata.
Please note this patch is just compiled tested.
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250318-mvneta-xdp-meta-v2-5-b6075778f61f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Set metadata size building the skb from xdp_buff in octeontx2 driver.
octeontx2 driver sets xdp headroom to OTX2_HEAD_ROOM
OTX2_HEAD_ROOM OTX2_ALIGN
OTX2_ALIGN 128
so the headroom is large enough to contain xdp_frame and xdp metadata.
Please note this patch is just compiled tested.
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250318-mvneta-xdp-meta-v2-4-b6075778f61f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Set metadata size building the skb from xdp_buff in netsec driver.
netsec driver sets xdp headroom to NETSEC_RXBUF_HEADROOM:
NETSEC_RXBUF_HEADROOM max(XDP_PACKET_HEADROOM, NET_SKB_PAD) + NET_IP_ALIGN
so the headroom is large enough to contain xdp_frame and xdp metadata.
Please note this patch is just compiled tested.
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250318-mvneta-xdp-meta-v2-3-b6075778f61f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Set metadata size building the skb from xdp_buff in mvpp2 driver
mvpp2 driver sets xdp headroom to:
MVPP2_MH_SIZE + MVPP2_SKB_HEADROOM
where
MVPP2_MH_SIZE 2
MVPP2_SKB_HEADROOM min(max(XDP_PACKET_HEADROOM, NET_SKB_PAD), 224)
so the headroom is large enough to contain xdp_frame and xdp metadata.
Please note this patch is just compiled tested.
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250318-mvneta-xdp-meta-v2-2-b6075778f61f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Set metadata size building the skb from xdp_buff in mvneta driver
mvneta sets xdp headroom to:
MVNETA_MH_SIZE + MVNETA_SKB_HEADROOM
where
MVNETA_MH_SIZE 2
MVNETA_SKB_HEADROOM max(NET_SKB_PAD, XDP_PACKET_HEADROOM)
so the headroom is large enough to contain xdp_frame and xdp metadata.
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250318-mvneta-xdp-meta-v2-1-b6075778f61f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is an effort to achieve W=1 kernel builds without warnings.
As part of that effort Helge Deller highlighted the following warnings
in the tulip driver when compiling with W=1 and CONFIG_TULIP_MWI=n:
.../tulip_core.c: In function ‘tulip_init_one’:
.../tulip_core.c:1309:22: warning: variable ‘force_csr0’ set but not used
This patch addresses that problem using IS_ENABLED(). This approach has
the added benefit of reducing conditionally compiled code. And thus
increasing compile coverage. E.g. for allmodconfig builds which enable
CONFIG_TULIP_MWI.
Compile tested only.
No run-time effect intended.
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250318-tulip-w1-v3-1-a813fadd164d@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
net/unix/*.c include many unnecessary header files (rtnetlink.h,
netdevice.h, etc).
Let's clean them up.
af_unix.c:
+uapi/linux/sockios.h : Only exist under include/uapi
+uapi/linux/termios.h : Only exist under include/uapi
-linux/freezer.h : No longer use freezable_schedule_timeout()
-linux/in.h : No ipv4_is_XXX() etc
-linux/module.h : No longer support CONFIG_UNIX=m
-linux/netdevice.h : No dev used
-linux/rtnetlink.h : Not part of rtnetlink API
-linux/signal.h : signal_pending() is defined in sched/signal.h
-linux/stat.h : No struct stat used
-net/checksum.h : CHECKSUM_UNNECESSARY is defined in skbuff.h
diag.c:
+linux/dcache.h : struct dentry in sk_diag_dump_vfs()
+linux/user_namespace.h : struct user_namespace in sk_diag_dump_uid()
+uapi/linux/unix_diag.h : Only exist under include/uapi/
garbage.c:
+linux/list.h : struct unix_{vertex,edge}, etc
+linux/workqueue.h : DECLARE_WORK(unix_gc_work, ...)
-linux/file.h : No fget() etc
-linux/kernel.h : No cond_resched() etc
-linux/netdevice.h : No dev used
-linux/proc_fs.h : No procfs provided
-linux/string.h : No memcpy(), kmemdup(), etc
sysctl_net_unix.c:
+linux/string.h : kmemdup()
+net/net_namespace.h : struct net, net_eq()
-linux/mm.h : slab.h is enough
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20250318034934.86708-5-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
include/net/af_unix.h indirectly includes some definitions for structs.
Let's include such headers explicitly.
linux/atomic.h : scm_stat.nr_fds
linux/net.h : unix_sock.peer_wq
linux/path.h : unix_sock.path
linux/spinlock.h : unix_sock.lock
linux/wait.h : unix_sock.peer_wake
uapi/linux/un.h : unix_address.name[]
linux/socket.h is removed as the structs there are not used directly,
and linux/un.h is clarified with uapi as un.h only exists under
include/uapi.
While at it, duplicate headers are removed from .c files.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20250318034934.86708-4-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
net/af_unix.h is included by core and some LSMs, but most definitions
need not be.
Let's move struct unix_{vertex,edge} to net/unix/garbage.c and other
definitions to net/unix/af_unix.h.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Link: https://patch.msgid.link/20250318034934.86708-3-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This is a prep patch to make the following changes cleaner.
No functional change intended.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Link: https://patch.msgid.link/20250318034934.86708-2-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Support adjusting/reading delayed ack max for socket level by using
set/getsockopt().
This option aligns with TCP_BPF_DELACK_MAX usage. Considering that bpf
option was implemented before this patch, so we need to use a standalone
new option for pure tcp set/getsockopt() use.
Add WRITE_ONCE/READ_ONCE() to prevent data-race if setsockopt()
happens to write one value to icsk_delack_max while icsk_delack_max is
being read.
Signed-off-by: Jason Xing <kerneljasonxing@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250317120314.41404-3-kerneljasonxing@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Support adjusting/reading RTO MIN for socket level by using set/getsockopt().
This new option has the same effect as TCP_BPF_RTO_MIN, which means it
doesn't affect RTAX_RTO_MIN usage (by using ip route...). Considering that
bpf option was implemented before this patch, so we need to use a standalone
new option for pure tcp set/getsockopt() use.
When the socket is created, its icsk_rto_min is set to the default
value that is controlled by sysctl_tcp_rto_min_us. Then if application
calls setsockopt() with TCP_RTO_MIN_US flag to pass a valid value, then
icsk_rto_min will be overridden in jiffies unit.
This patch adds WRITE_ONCE/READ_ONCE to avoid data-race around
icsk_rto_min.
Signed-off-by: Jason Xing <kerneljasonxing@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250317120314.41404-2-kerneljasonxing@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Extend flood test to configure FDB entry with unresolved destination IP,
check that packets are not sent twice.
Without the previous patch which handles such scenario in mlxsw, the
tests fail:
$ TESTS='test_flood' ./vxlan_bridge_1d.sh
Running tests with UDP port 4789
TEST: VXLAN: flood [ OK ]
TEST: VXLAN: flood, unresolved FDB entry [FAIL]
vx2 ns2: Expected to capture 10 packets, got 20.
$ TESTS='test_flood' ./vxlan_bridge_1q.sh
INFO: Running tests with UDP port 4789
TEST: VXLAN: flood vlan 10 [ OK ]
TEST: VXLAN: flood vlan 20 [ OK ]
TEST: VXLAN: flood vlan 10, unresolved FDB entry [FAIL]
vx10 ns2: Expected to capture 10 packets, got 20.
TEST: VXLAN: flood vlan 20, unresolved FDB entry [FAIL]
vx20 ns2: Expected to capture 10 packets, got 20.
With the previous patch, the tests pass.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/7bc96e317531f3bf06319fb2ea447bd8666f29fa.1742224300.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When hardware floods packets to bridge ports, but flooding to VXLAN bridge
port fails during encapsulation to one of the remote VTEPs, the packets are
trapped to CPU. In such case, the packets are marked with
skb->offload_fwd_mark, which means that packet was L2-forwarded in
hardware. Software data path repeats flooding, but packets which are
marked with skb->offload_fwd_mark will not be flooded by the bridge to
bridge ports which are in the same hardware domain as the ingress port.
Currently, mlxsw does not add VXLAN bridge ports to the same hardware
domain as physical bridge ports despite the fact that the device is able
to forward packets to and from VXLAN tunnels in hardware. In some scenarios
(as mentioned above) this can result in remote VTEPs receiving duplicate
packets. The packets are first flooded by hardware and after an
encapsulation failure, they are flooded again to all remote VTEPs by
software.
Solve this by adding VXLAN bridge ports to the same hardware domain as
physical bridge ports, so then nbp_switchdev_allowed_egress() will return
false also for VXLAN, and packets will not be sent twice from VXLAN device.
switchdev_bridge_port_offload() should get vxlan_dev not as const, so
some changes are required. Call switchdev API from
mlxsw_sp_bridge_vxlan_{join,leave}() which handle offload configurations.
Reported-by: Vladimir Oltean <olteanv@gmail.com>
Closes: https://lore.kernel.org/all/20250210152246.4ajumdchwhvbarik@skbuf/
Reported-by: Vladyslav Mykhaliuk <vmykhaliuk@nvidia.com>
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/7279056843140fae3a72c2d204c7886b79d03899.1742224300.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Next patch will call __mlxsw_sp_bridge_vxlan_leave() from
mlxsw_sp_bridge_vxlan_join() as part of error flow, move the function to
be able to call the second one.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/64750a0965536530482318578bada30fac372b8a.1742224300.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
Russell King (Oracle)
Edward Cree
Eric Dumazet
Kuniyuki Iwashima
Jianbo Liu
Paul Blakey
Shay Drory
Amir Tzin
Mark Bloch
Tariq Toukan
Jing Su
Dmitry Safonov
Jiri Pirko
Lorenzo Bianconi
Simon Horman
Jason Xing
Amit Cohen