| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Since commit 9c66d1564676 ("taprio: Add support for hardware
offloading") there's a bit of inconsistency when offloading schedules
to the hardware:
In software mode, the gate masks are specified in terms of traffic
classes, so if say "sched-entry S 03 20000", it means that the traffic
classes 0 and 1 are open for 20us; when taprio is offloaded to
hardware, the gate masks are specified in terms of hardware queues.
The idea here is to fix hardware offloading, so schedules in hardware
and software mode have the same behavior. What's needed to do is to
map traffic classes to queues when applying the offload to the driver.
Fixes: 9c66d1564676 ("taprio: Add support for hardware offloading")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If USB_NET_CDC_NCM is y and USB_NET_CDCETHER is m, build fails:
drivers/net/usb/cdc_ncm.o:(.rodata+0x1d8): undefined reference to `usbnet_cdc_update_filter'
Select USB_NET_CDCETHER for USB_NET_CDC_NCM to fix this.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: e10dcb1b6ba7 ("net: cdc_ncm: hook into set_rx_mode to admit multicast traffic")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
when skb->encapsulation is 0, skb->ip_summed is CHECKSUM_PARTIAL
and it is udp packet, which has a dest port as the IANA assigned.
the hardware is expected to do the checksum offload, but the
hardware will not do the checksum offload when udp dest port is
6081.
This patch fixes it by doing the checksum in software.
Reported-by: Li Bing <libing@winhong.com>
Signed-off-by: Yi Li <yili@winhong.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The recent changes to support user-defined RSS map assume that RX
rings are always reserved and the default RSS map is set after the
RX rings are successfully reserved. If the firmware spec is older
than 1.6.1, no ring reservations are required and the default RSS
map is not setup at all. In another scenario where the fw Resource
Manager is older, RX rings are not reserved and we also end up with
no valid RSS map.
Fix both issues in bnxt_need_reserve_rings(). In both scenarios
described above, we don't need to reserve RX rings so we need to
call this new function bnxt_check_rss_map_no_rmgr() to setup the
default RSS map when needed.
Without valid RSS map, the NIC won't receive packets properly.
Fixes: 1667cbf6a4eb ("bnxt_en: Add logical RSS indirection table structure.")
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are no VF rings available during probe when the device is configured
using the Minimal-Static reservation strategy. In this case, the RSS
indirection table can only be initialized later, during bnxt_open_nic().
However, this was not happening because the rings will already have been
reserved via bnxt_init_dflt_ring_mode(), causing bnxt_need_reserve_rings()
to return false in bnxt_reserve_rings() and bypass the RSS table init.
Solve this by pushing the call to bnxt_set_dflt_rss_indir_tbl() into
__bnxt_reserve_rings(), which is common to both paths and is called
whenever ring configuration is changed. After doing this, the RSS table
init that must be called from bnxt_init_one() happens implicitly via
bnxt_set_default_rings(), necessitating doing the allocation earlier in
order to avoid a null pointer dereference.
Fixes: bd3191b5d87d ("bnxt_en: Implement ethtool -X to set indirection table.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Firmware returns RESOURCE_ACCESS_DENIED for HWRM_TEMP_MONITORY_QUERY for
VFs. This produces unpleasing error messages in the log when temp1_input
is queried via the hwmon sysfs interface from a VF.
The error is harmless and expected, so silence it and return unknown as
the value. Since the device temperature is not particularly sensitive
information, provide flexibility to change this policy in future by
silencing the error rather than avoiding the HWRM call entirely for VFs.
Fixes: cde49a42a9bb ("bnxt_en: Add hwmon sysfs support to read temperature")
Cc: Marc Smith <msmith626@gmail.com>
Reported-by: Marc Smith <msmith626@gmail.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bnxt_fw_reset_task() is run from a delayed workqueue. The current
code is not cancelling the workqueue in the driver's .remove()
method and it can potentially crash if the device is removed with
the workqueue still pending.
The fix is to clear the BNXT_STATE_IN_FW_RESET flag and then cancel
the delayed workqueue in bnxt_remove_one(). bnxt_queue_fw_reset_work()
also needs to check that this flag is set before scheduling. This
will guarantee that no rescheduling will be done after it is cancelled.
Fixes: 230d1f0de754 ("bnxt_en: Handle firmware reset.")
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a PCI error is detected the PCI state could be corrupt, save
the PCI state after initialization and restore it after the slot
reset.
Fixes: 6316ea6db93d ("bnxt_en: Enable AER support.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are returning the wrong count for ETH_SS_STATS in get_sset_count()
when XDP or TCs are enabled. In a recent commit, we got rid of
irrelevant counters when the ring is RX only or TX only, but we
did not make the proper adjustments for the count. As a result,
when we have XDP or TCs enabled, we are returning an excess count
because some of the rings are TX only. This causes ethtool -S to
display extra counters with no counter names.
Fix bnxt_get_num_ring_stats() by not assuming that all rings will
always have RX and TX counters in combined mode.
Fixes: 125592fbf467 ("bnxt_en: show only relevant ethtool stats for a TX or RX ring")
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If firmware goes into unstable state, HWRM_NVM_GET_DIR_INFO firmware
command may return zero dir entries. Return error in such case to
avoid zero length dma buffer request.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In rare conditions like two stage OS installation, the
ethtool's get_channels function may be called when the
device is in D3 state, leading to uncorrectable PCI error.
Check netif_running() first before making any query to FW
which involves writing to BAR.
Fixes: db4723b3cd2d ("bnxt_en: Check max_tx_scheduler_inputs value from firmware.")
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The RGMII control register at 0x32 indicates the states for the bits
RGMII_TX_CLK_DELAY and RGMII_RX_CLK_DELAY as follows:
RGMII Transmit/Receive Clock Delay
0x0 = RGMII transmit clock is shifted with respect to transmit/receive data.
0x1 = RGMII transmit clock is aligned with respect to transmit/receive data.
This commit fixes the inversed behavior of these bits
Fixes: 736b25afe284 ("net: dp83869: Add RGMII internal delay configuration")
Signed-off-by: Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At the time of do_rest, ibmvnic tries to re-initalize the tx_pools
and rx_pools to avoid re-allocating the long term buffer. However
there is a window inside do_reset that the tx_pools and
rx_pools were freed before re-initialized making it possible to deference
null pointers.
This patch fix this issue by always check the tx_pool
and rx_pool are not NULL after ibmvnic_login. If so, re-allocating
the pools. This will avoid getting into calling reset_tx/rx_pools with
NULL adapter tx_pools/rx_pools pointer. Also add null pointer check in
reset_tx_pools and reset_rx_pools to safe handle NULL pointer case.
Signed-off-by: Mingming Cao <mmc@linux.vnet.ibm.com>
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To flush the vid + mc entries from ALE, which is required when a VLAN
interface is removed, driver needs to call cpsw_ale_flush_multicast()
with ALE_PORT_HOST for port mask as these entries are added only for
host port. Without this, these entries remain in the ALE table even
after removing the VLAN interface. cpsw_ale_flush_multicast() calls
cpsw_ale_flush_mcast which expects a port mask to do the job.
Fixes: ed3525eda4c4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To flush the vid + mc entries from ALE, which is required when a VLAN
interface is removed, driver needs to call cpsw_ale_flush_multicast()
with ALE_PORT_HOST for port mask as these entries are added only for
host port. Without this, these entries remain in the ALE table even
after removing the VLAN interface. cpsw_ale_flush_multicast() calls
cpsw_ale_flush_mcast which expects a port mask to do the job.
Fixes: 15180eca569b ("net: ethernet: ti: cpsw: fix vlan mcast")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cfpkt_peek_head return 0 and 1, caller is checking error using <0
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Every iteration of for_each_child_of_node() decrements
the reference count of the previous node, however when control
is transferred from the middle of the loop, as in the case of
a return or break or goto, there is no decrement thus ultimately
resulting in a memory leak.
Fix a potential memory leak in mt7530.c by inserting of_node_put()
before the break and return statements.
Issue found with Coccinelle.
Signed-off-by: Sumera Priyadarsini <sylphrenadin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During a dump, this attribute is essential, it enables the userspace to
know on which interface the context is linked to.
Fixes: 459aa660eb1d ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Tested-by: Gabriel Ganne <gabriel.ganne@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
check_fcs() was returning bool as 0/1, which was a sign that the sense
of the function was unclear: false was good, which doesn't really match
a name like 'check_$thing'. So rename it to ef100_has_fcs_error(), and
use proper booleans in the return statements.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Every iteration of for_each_available_child_of_node() decrements
the reference count of the previous node, however when control
is transferred from the middle of the loop, as in the case of
a return or break or goto, there is no decrement thus ultimately
resulting in a memory leak.
Fix a potential memory leak in felix.c by inserting of_node_put()
before the return statement.
Issue found with Coccinelle.
Signed-off-by: Sumera Priyadarsini <sylphrenadin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix spelling mistake documenation -> documentation.
Fixes: 5a18bb14c0f7 ("dt-bindings: net: dsa: Let dsa.txt refer to dsa.yaml")
Signed-off-by: Kurt Kanzenbach <kurt@kmk-computers.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When make_rate() fails, vcc should be freed just
like other error paths in fs_open().
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When devm_gpiod_get_optional() fails, bus should be
freed just like when of_mdiobus_register() fails.
Fixes: 1bddd96cba03d ("net: arc_emac: support the phy reset for emac driver")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When down_killable() fails, skb_resp should be freed
just like when st95hf_spi_send() fails.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
My last significant achievements to the PHY library was ensuring we
would have small bus factor by having Andrew and Heiner added. The world
has moved on past 1G, but I have not, so let more competent maintainers
take over.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add an entry for the Broadcom Ethernet PHY drivers covering the BCM63xx,
BCM7xxx, BCM87xx, BCM54140, BCM84881, the venerable broadcom.c driver
and the companion library files.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for removing myself from the PHYLIB entry, add the UniMAC
MDIO controller files (DT binding, driver and platform_data header) to
the GENET entry. The UniMAC MDIO controller is essential to the GENET
operation, therefore it makes sense to group them together.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the DT binding was added in aab5127d94e6 ("Documentation: add
Device tree bindings for Broadcom GENET"), the file was not explicitly
listed under the GENET MAINTAINERS section, do that now.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the binding was added with 967dd82ffc52 ("net: dsa: b53: Add
support for Broadcom RoboSwitch"), it was not explicitly added to the
B53 MAINTAINERS file section, add it now.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When commit b0ba512e25d7 ("net: bcmgenet: enable driver to work without
a device tree") added include/linux/platform_data/bcmgenet.h, the file
was not added to the GENET MAINTAINERS file section, add it now.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clang warns:
drivers/net/dsa/sja1105/sja1105_main.c:3418:38: warning: address of
array 'match->compatible' will always evaluate to 'true'
[-Wpointer-bool-conversion]
for (match = sja1105_dt_ids; match->compatible; match++) {
~~~ ~~~~~~~^~~~~~~~~~
1 warning generated.
We should check the value of the first character in compatible to see if
it is empty or not. This matches how the rest of the tree iterates over
IDs.
Fixes: 0b0e299720bb ("net: dsa: sja1105: use detected device id instead of DT one on mismatch")
Link: https://github.com/ClangBuiltLinux/linux/issues/1139
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function consume_skb is only meaningful when tracing is enabled.
This patch makes it conditional on CONFIG_TRACEPOINTS.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The underlying Ethernet device may request necessary tailroom to be
allocated by setting needed_tailroom. This driver should also set
needed_tailroom to request the tailroom needed by the underlying
Ethernet device to be allocated.
Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes two main problems seen when removing NetLabel
mappings: memory leaks and potentially extra audit noise.
The memory leaks are caused by not properly free'ing the mapping's
address selector struct when free'ing the entire entry as well as
not properly cleaning up a temporary mapping entry when adding new
address selectors to an existing entry. This patch fixes both these
problems such that kmemleak reports no NetLabel associated leaks
after running the SELinux test suite.
The potentially extra audit noise was caused by the auditing code in
netlbl_domhsh_remove_entry() being called regardless of the entry's
validity. If another thread had already marked the entry as invalid,
but not removed/free'd it from the list of mappings, then it was
possible that an additional mapping removal audit record would be
generated. This patch fixes this by returning early from the removal
function when the entry was previously marked invalid. This change
also had the side benefit of improving the code by decreasing the
indentation level of large chunk of code by one (accounting for most
of the diffstat).
Fixes: 63c416887437 ("netlabel: Add network address selectors to the NetLabel/LSM domain mapping")
Reported-by: Stephen Smalley <stephen.smalley.work@gmail.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With disabling bh in the whole sctp_get_port_local(), when
snum == 0 and too many ports have been used, the do-while
loop will take the cpu for a long time and cause cpu stuck:
[ ] watchdog: BUG: soft lockup - CPU#11 stuck for 22s!
[ ] RIP: 0010:native_queued_spin_lock_slowpath+0x4de/0x940
[ ] Call Trace:
[ ] _raw_spin_lock+0xc1/0xd0
[ ] sctp_get_port_local+0x527/0x650 [sctp]
[ ] sctp_do_bind+0x208/0x5e0 [sctp]
[ ] sctp_autobind+0x165/0x1e0 [sctp]
[ ] sctp_connect_new_asoc+0x355/0x480 [sctp]
[ ] __sctp_connect+0x360/0xb10 [sctp]
There's no need to disable bh in the whole function of
sctp_get_port_local. So fix this cpu stuck by removing
local_bh_disable() called at the beginning, and using
spin_lock_bh() instead.
The same thing was actually done for inet_csk_get_port() in
Commit ea8add2b1903 ("tcp/dccp: better use of ephemeral
ports in bind()").
Thanks to Marcelo for pointing the buggy code out.
v1->v2:
- use cond_resched() to yield cpu to other tasks if needed,
as Eric noticed.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When this driver is built as a module, I cannot rmmod it after insmoding
it.
This is because that this driver calls ravb_mdio_init() at the time of
probe, and module->refcnt is incremented by alloc_mdio_bitbang() called
after that.
Therefore, even if ifup is not performed, the driver is in use and rmmod
cannot be performed.
$ lsmod
Module Size Used by
ravb 40960 1
$ rmmod ravb
rmmod: ERROR: Module ravb is in use
Call ravb_mdio_init() at open and free_mdio_bitbang() at close, thereby
rmmod is possible in the ifdown state.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Yuusuke Ashizuka <ashiduka@fujitsu.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 32927393dc1c ("sysctl: pass kernel pointers to ->proc_handler")
changed ndisc_ifinfo_sysctl_change to take a kernel pointer. Adjust its
prototype in net/ndisc.h as well to fix the following sparse warning:
net/ipv6/ndisc.c:1838:5: error: symbol 'ndisc_ifinfo_sysctl_change' redeclared with different type (incompatible argument 3 (different address spaces)):
net/ipv6/ndisc.c:1838:5: int extern [addressable] [signed] [toplevel] ndisc_ifinfo_sysctl_change( ... )
net/ipv6/ndisc.c: note: in included file (through include/net/ipv6.h):
./include/net/ndisc.h:496:5: note: previously declared as:
./include/net/ndisc.h:496:5: int extern [addressable] [signed] [toplevel] ndisc_ifinfo_sysctl_change( ... )
net/ipv6/ndisc.c: note: in included file (through include/net/ip6_route.h):
Fixes: 32927393dc1c ("sysctl: pass kernel pointers to ->proc_handler")
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When devm_kcalloc() fails, dev should be freed just
like what we've done in the subsequent error paths.
Fixes: 7b78be48a8eb6 ("net: systemport: Dynamically allocate number of TX rings")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
hns_nic_dev_probe allocates ndev, but not free it on
two error handling paths, which may lead to memleak.
Fixes: 63434888aaf1b ("net: hns: net: hns: enet adds support of acpi")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
When adding a new fd to an epoll, and that this new fd is an
epoll fd itself, we recursively scan the fds attached to it
to detect cycles, and add non-epool files to a "check list"
that gets subsequently parsed.
However, this check list isn't completely safe when deletions
can happen concurrently. To sidestep the issue, make sure that
a struct file placed on the check list sees its f_count increased,
ensuring that a concurrent deletion won't result in the file
disapearing from under our feet.
Cc: stable@vger.kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Currently the nexthop code will use an empty NHA_GROUP attribute, but it
requires at least 1 entry in order to function properly. Otherwise we
end up derefencing null or random pointers all over the place due to not
having any nh_grp_entry members allocated, nexthop code relies on having at
least the first member present. Empty NHA_GROUP doesn't make any sense so
just disallow it.
Also add a WARN_ON for any future users of nexthop_create_group().
BUG: kernel NULL pointer dereference, address: 0000000000000080
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] SMP
CPU: 0 PID: 558 Comm: ip Not tainted 5.9.0-rc1+ #93
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-2.fc32 04/01/2014
RIP: 0010:fib_check_nexthop+0x4a/0xaa
Code: 0f 84 83 00 00 00 48 c7 02 80 03 f7 81 c3 40 80 fe fe 75 12 b8 ea ff ff ff 48 85 d2 74 6b 48 c7 02 40 03 f7 81 c3 48 8b 40 10 <48> 8b 80 80 00 00 00 eb 36 80 78 1a 00 74 12 b8 ea ff ff ff 48 85
RSP: 0018:ffff88807983ba00 EFLAGS: 00010213
RAX: 0000000000000000 RBX: ffff88807983bc00 RCX: 0000000000000000
RDX: ffff88807983bc00 RSI: 0000000000000000 RDI: ffff88807bdd0a80
RBP: ffff88807983baf8 R08: 0000000000000dc0 R09: 000000000000040a
R10: 0000000000000000 R11: ffff88807bdd0ae8 R12: 0000000000000000
R13: 0000000000000000 R14: ffff88807bea3100 R15: 0000000000000001
FS: 00007f10db393700(0000) GS:ffff88807dc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000080 CR3: 000000007bd0f004 CR4: 00000000003706f0
Call Trace:
fib_create_info+0x64d/0xaf7
fib_table_insert+0xf6/0x581
? __vma_adjust+0x3b6/0x4d4
inet_rtm_newroute+0x56/0x70
rtnetlink_rcv_msg+0x1e3/0x20d
? rtnl_calcit.isra.0+0xb8/0xb8
netlink_rcv_skb+0x5b/0xac
netlink_unicast+0xfa/0x17b
netlink_sendmsg+0x334/0x353
sock_sendmsg_nosec+0xf/0x3f
____sys_sendmsg+0x1a0/0x1fc
? copy_msghdr_from_user+0x4c/0x61
___sys_sendmsg+0x63/0x84
? handle_mm_fault+0xa39/0x11b5
? sockfd_lookup_light+0x72/0x9a
__sys_sendmsg+0x50/0x6e
do_syscall_64+0x54/0xbe
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7f10dacc0bb7
Code: d8 64 89 02 48 c7 c0 ff ff ff ff eb cd 66 0f 1f 44 00 00 8b 05 9a 4b 2b 00 85 c0 75 2e 48 63 ff 48 63 d2 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 01 c3 48 8b 15 b1 f2 2a 00 f7 d8 64 89 02 48
RSP: 002b:00007ffcbe628bf8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007ffcbe628f80 RCX: 00007f10dacc0bb7
RDX: 0000000000000000 RSI: 00007ffcbe628c60 RDI: 0000000000000003
RBP: 000000005f41099c R08: 0000000000000001 R09: 0000000000000008
R10: 00000000000005e9 R11: 0000000000000246 R12: 0000000000000000
R13: 0000000000000000 R14: 00007ffcbe628d70 R15: 0000563a86c6e440
Modules linked in:
CR2: 0000000000000080
CC: David Ahern <dsahern@gmail.com>
Fixes: 430a049190de ("nexthop: Add support for nexthop groups")
Reported-by: syzbot+a61aa19b0c14c8770bd9@syzkaller.appspotmail.com
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes: f516fb704d02fff2 ("dt-bindings: Whitespace clean-ups in schema files")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200819092058.1526-1-geert+renesas@glider.be
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
When an MMU notifier call results in unmapping a range that spans multiple
PGDs, we end up calling into cond_resched_lock() when crossing a PGD boundary,
since this avoids running into RCU stalls during VM teardown. Unfortunately,
if the VM is destroyed as a result of OOM, then blocking is not permitted
and the call to the scheduler triggers the following BUG():
| BUG: sleeping function called from invalid context at arch/arm64/kvm/mmu.c:394
| in_atomic(): 1, irqs_disabled(): 0, non_block: 1, pid: 36, name: oom_reaper
| INFO: lockdep is turned off.
| CPU: 3 PID: 36 Comm: oom_reaper Not tainted 5.8.0 #1
| Hardware name: QEMU QEMU Virtual Machine, BIOS 0.0.0 02/06/2015
| Call trace:
| dump_backtrace+0x0/0x284
| show_stack+0x1c/0x28
| dump_stack+0xf0/0x1a4
| ___might_sleep+0x2bc/0x2cc
| unmap_stage2_range+0x160/0x1ac
| kvm_unmap_hva_range+0x1a0/0x1c8
| kvm_mmu_notifier_invalidate_range_start+0x8c/0xf8
| __mmu_notifier_invalidate_range_start+0x218/0x31c
| mmu_notifier_invalidate_range_start_nonblock+0x78/0xb0
| __oom_reap_task_mm+0x128/0x268
| oom_reap_task+0xac/0x298
| oom_reaper+0x178/0x17c
| kthread+0x1e4/0x1fc
| ret_from_fork+0x10/0x30
Use the new 'flags' argument to kvm_unmap_hva_range() to ensure that we
only reschedule if MMU_NOTIFIER_RANGE_BLOCKABLE is set in the notifier
flags.
Cc: <stable@vger.kernel.org>
Fixes: 8b3405e345b5 ("kvm: arm/arm64: Fix locking for kvm_free_stage2_pgd")
Cc: Marc Zyngier <maz@kernel.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Message-Id: <20200811102725.7121-3-will@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The 'flags' field of 'struct mmu_notifier_range' is used to indicate
whether invalidate_range_{start,end}() are permitted to block. In the
case of kvm_mmu_notifier_invalidate_range_start(), this field is not
forwarded on to the architecture-specific implementation of
kvm_unmap_hva_range() and therefore the backend cannot sensibly decide
whether or not to block.
Add an extra 'flags' parameter to kvm_unmap_hva_range() so that
architectures are aware as to whether or not they are permitted to block.
Cc: <stable@vger.kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Message-Id: <20200811102725.7121-2-will@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The phy-connection-type parameter is described in ePAPR 1.1:
Specifies interface type between the Ethernet device and a physical
layer (PHY) device. The value of this property is specific to the
implementation.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Link: https://lore.kernel.org/r/1597917724-11127-1-git-send-email-madalin.bucur@oss.nxp.com
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The intel,lgm-pcie binding is matching on all snps,dw-pcie instances
which is wrong. Add a custom 'select' entry to fix this.
Fixes: e54ea45a4955 ("dt-bindings: PCI: intel: Add YAML schemas for the PCIe RC controller")
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Reviewed-by: Dilip Kota <eswara.kota@linux.intel.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Also remove trailing whitespaces in bpf_skb_get_tunnel_key example code.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200821133642.18870-1-tklauser@distanz.ch
|
|
clang static analysis reports this problem
b53_common.c:1583:13: warning: The left expression of the compound
assignment is an uninitialized value. The computed value will
also be garbage
ent.port &= ~BIT(port);
~~~~~~~~ ^
ent is set by a successful call to b53_arl_read(). Unsuccessful
calls are caught by an switch statement handling specific returns.
b32_arl_read() calls b53_arl_op_wait() which fails with the
unhandled -ETIMEDOUT.
So add -ETIMEDOUT to the switch statement. Because
b53_arl_op_wait() already prints out a message, do not add another
one.
Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Tom Rix <trix@redhat.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the 32-bit vdso Makefile to the vdso_install rule so that 'make
vdso_install' installs the 32-bit compat vdso when it is compiled.
Fixes: a7f71a2c8903 ("arm64: compat: Add vDSO")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Acked-by: Will Deacon <will@kernel.org>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Link: https://lore.kernel.org/r/20200818014950.42492-1-swboyd@chromium.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
Vinicius Costa Gomes
YueHaibing
Yi Li
Michael Chan
Edwin Peer
Vasundhara Volam
Pavan Chebbi
Daniel Gorsulowski
Mingming Cao
Murali Karicheri
Tong Zhang
Sumera Priyadarsini
Nicolas Dichtel
Edward Cree
Kurt Kanzenbach
Dinghao Liu
Florian Fainelli
Nathan Chancellor
Herbert Xu
Xie He
Paul Moore
Xin Long
Yuusuke Ashizuka
Tobias Klauser
Al Viro
Marc Zyngier
Nikolay Aleksandrov
Geert Uytterhoeven
Will Deacon
Madalin Bucur
Rob Herring
Tom Rix
Stephen Boyd