| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Based on further tests, it seems that the QDMA shaper is not able to
perform shaping close to the MAC link rate without throughput loss.
This cannot be compensated by increasing the shaping rate, so it seems
to be an internal limit.
Fix the remaining throughput regression by detecting that condition and
limiting shaping to ports with lower link speed.
This patch intentionally ignores link speed gain from TRGMII, because
even on such links, shaping to 1000 Mbit/s incurs some throughput
degradation.
Fixes: f63959c7eec3 ("net: ethernet: mtk_eth_soc: implement multi-queue support for per-port queues")
Tested-By: Frank Wunderlich <frank-w@public-files.de>
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The force watchdog event bit is not cleared during SW reset in the
mv88e6393x switch. This is a different behavior compared to mv886390 which
clears the force WD event bit as advertised. This causes a force WD event
to be handled over and over again as the SW reset following the event never
clears the force WD event bit.
Explicitly clear the watchdog event register to 0 in irq_action when
handling an event to prevent the switch from sending continuous interrupts.
Marvell aren't aware of any other stuck bits apart from the force WD
bit.
Fixes: de776d0d316f ("net: dsa: mv88e6xxx: add support for mv88e6393x family"
Signed-off-by: Gustav Ekelund <gustaek@axis.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 0db3dc73f7a3 ("[NETPOLL]: tx lock deadlock fix") narrowed
down the region under netif_tx_trylock() inside netpoll_send_skb().
(At that point in time netif_tx_trylock() would lock all queues of
the device.) Taking the tx lock was problematic because driver's
cleanup method may take the same lock. So the change made us hold
the xmit lock only around xmit, and expected the driver to take
care of locking within ->ndo_poll_controller().
Unfortunately this only works if netpoll isn't itself called with
the xmit lock already held. Netpoll code is careful and uses
trylock(). The drivers, however, may be using plain lock().
Printing while holding the xmit lock is going to result in rare
deadlocks.
Luckily we record the xmit lock owners, so we can scan all the queues,
the same way we scan NAPI owners. If any of the xmit locks is held
by the local CPU we better not attempt any polling.
It would be nice if we could narrow down the check to only the NAPIs
and the queue we're trying to use. I don't see a way to do that now.
Reported-by: Roman Gushchin <roman.gushchin@linux.dev>
Fixes: 0db3dc73f7a3 ("[NETPOLL]: tx lock deadlock fix")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzbot was able to trigger a panic [1] in icmp_glue_bits(), or
more exactly in skb_copy_and_csum_bits()
There is no repro yet, but I think the issue is that syzbot
manages to lower device mtu to a small value, fooling __icmp_send()
__icmp_send() must make sure there is enough room for the
packet to include at least the headers.
We might in the future refactor skb_copy_and_csum_bits() and its
callers to no longer crash when something bad happens.
[1]
kernel BUG at net/core/skbuff.c:3343 !
invalid opcode: 0000 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 15766 Comm: syz-executor.0 Not tainted 6.3.0-rc4-syzkaller-00039-gffe78bbd5121 #0
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-2 04/01/2014
RIP: 0010:skb_copy_and_csum_bits+0x798/0x860 net/core/skbuff.c:3343
Code: f0 c1 c8 08 41 89 c6 e9 73 ff ff ff e8 61 48 d4 f9 e9 41 fd ff ff 48 8b 7c 24 48 e8 52 48 d4 f9 e9 c3 fc ff ff e8 c8 27 84 f9 <0f> 0b 48 89 44 24 28 e8 3c 48 d4 f9 48 8b 44 24 28 e9 9d fb ff ff
RSP: 0018:ffffc90000007620 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 00000000000001e8 RCX: 0000000000000100
RDX: ffff8880276f6280 RSI: ffffffff87fdd138 RDI: 0000000000000005
RBP: 0000000000000000 R08: 0000000000000005 R09: 0000000000000000
R10: 00000000000001e8 R11: 0000000000000001 R12: 000000000000003c
R13: 0000000000000000 R14: ffff888028244868 R15: 0000000000000b0e
FS: 00007fbc81f1c700(0000) GS:ffff88802ca00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000001b2df43000 CR3: 00000000744db000 CR4: 0000000000150ef0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<IRQ>
icmp_glue_bits+0x7b/0x210 net/ipv4/icmp.c:353
__ip_append_data+0x1d1b/0x39f0 net/ipv4/ip_output.c:1161
ip_append_data net/ipv4/ip_output.c:1343 [inline]
ip_append_data+0x115/0x1a0 net/ipv4/ip_output.c:1322
icmp_push_reply+0xa8/0x440 net/ipv4/icmp.c:370
__icmp_send+0xb80/0x1430 net/ipv4/icmp.c:765
ipv4_send_dest_unreach net/ipv4/route.c:1239 [inline]
ipv4_link_failure+0x5a9/0x9e0 net/ipv4/route.c:1246
dst_link_failure include/net/dst.h:423 [inline]
arp_error_report+0xcb/0x1c0 net/ipv4/arp.c:296
neigh_invalidate+0x20d/0x560 net/core/neighbour.c:1079
neigh_timer_handler+0xc77/0xff0 net/core/neighbour.c:1166
call_timer_fn+0x1a0/0x580 kernel/time/timer.c:1700
expire_timers+0x29b/0x4b0 kernel/time/timer.c:1751
__run_timers kernel/time/timer.c:2022 [inline]
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: syzbot+d373d60fddbdc915e666@syzkaller.appspotmail.com
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230330174502.1915328-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit c5b959eeb7f9e40673b97c08c71cbfff5f5923f2.
Reverted change is required after commit 3948b05950fd ("net: introduce
a config option to tweak MAX_SKB_FRAGS") which does not exist
in this tree, yet. It's only present in -next trees at the time
of writing.
Reported-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/all/20230331214444.GA1426512@dev-arch.thelio-3990X/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This adds conversion of VMCI specific error code to general -ENOMEM. It
is needed, because af_vsock.c passes error value returned from transport
to the user, which does not expect to get VMCI_ERROR_* values.
Fixes: c43170b7e157 ("vsock: return errors other than -ENOMEM to socket")
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Vishnu Dasa <vdasa@vmware.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When playing with various compilers or their versions, some choke on
the t7xx code. For example (with gcc 13):
In file included from ./arch/s390/include/generated/asm/rwonce.h:1,
from ../include/linux/compiler.h:247,
from ../include/linux/build_bug.h:5,
from ../include/linux/bits.h:22,
from ../drivers/net/wwan/t7xx/t7xx_state_monitor.c:17:
In function 'preempt_count',
inlined from 't7xx_fsm_append_event' at ../drivers/net/wwan/t7xx/t7xx_state_monitor.c:439:43:
../include/asm-generic/rwonce.h:44:26: error: array subscript 0 is outside array bounds of 'const volatile int[0]' [-Werror=array-bounds=]
There is no reason for any code in the kernel to be built with -Werror
by default. Note that we have generic CONFIG_WERROR. So if anyone wants
-Werror, they can enable that.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/all/20230330232717.1f8bf5ea@kernel.org/
Cc: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Cc: Intel Corporation <linuxwwan@intel.com>
Cc: Chiranjeevi Rapolu <chiranjeevi.rapolu@linux.intel.com>
Cc: Liu Haijun <haijun.liu@mediatek.com>
Cc: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Cc: Ricardo Martinez <ricardo.martinez@linux.intel.com>
Cc: Loic Poulain <loic.poulain@linaro.org>
Cc: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The type of MAX_SKB_FRAGS has changed recently, so the debug printk
needs to be updated:
drivers/net/ethernet/ti/netcp_core.c: In function 'netcp_create_interface':
drivers/net/ethernet/ti/netcp_core.c:2084:30: error: format '%ld' expects argument of type 'long int', but argument 3 has type 'int' [-Werror=format=]
2084 | dev_err(dev, "tx-pool size too small, must be at least %ld\n",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: 3948b05950fd ("net: introduce a config option to tweak MAX_SKB_FRAGS")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 65b32f801bfb ("uapi: move IPPROTO_L2TP to in.h") moved the
definition of IPPROTO_L2TP from a define to an enum, but since
__stringify doesn't work properly with enums, we ended up breaking the
modalias strings for the l2tp modules:
$ modinfo l2tp_ip l2tp_ip6 | grep alias
alias: net-pf-2-proto-IPPROTO_L2TP
alias: net-pf-2-proto-2-type-IPPROTO_L2TP
alias: net-pf-10-proto-IPPROTO_L2TP
alias: net-pf-10-proto-2-type-IPPROTO_L2TP
Use the resolved number directly in MODULE_ALIAS_*() macros (as we
already do with SOCK_DGRAM) to fix the alias strings:
$ modinfo l2tp_ip l2tp_ip6 | grep alias
alias: net-pf-2-proto-115
alias: net-pf-2-proto-115-type-2
alias: net-pf-10-proto-115
alias: net-pf-10-proto-115-type-2
Moreover, fix the ordering of the parameters passed to
MODULE_ALIAS_NET_PF_PROTO_TYPE() by switching proto and type.
Fixes: 65b32f801bfb ("uapi: move IPPROTO_L2TP to in.h")
Link: https://lore.kernel.org/lkml/ZCQt7hmodtUaBlCP@righiandr-XPS-13-7390
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Andrea Righi <andrea.righi@canonical.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, intel_speed_mode_2500() will fix-up xpcs_an_inband
to 1 if the underlying controller has a max speed of 1000Mbps.
The value has been initialized and modified if it is
a fixed-linked setup earlier.
This patch removes the fix-up to allow for fixed-linked setup
support. In stmmac_phy_setup(), ovr_an_inband is set based on
the value of xpcs_an_inband. Which in turn will return an
error in phylink_parse_mode() where MLO_AN_FIXED and
ovr_an_inband are both set.
Fixes: c82386310d95 ("stmmac: intel: prepare to support 1000BASE-X phy interface setting")
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After the introduction of the fixed-link support, the MAC driver
no longer attempt to scan for a PHY to attach to. This causes the
non fixed-link setups to stop working.
Using the phylink_expects_phy() to check and determine if the MAC
should expect and attach a PHY.
Fixes: ab21cf920928 ("net: stmmac: make mdio register skips PHY scanning for fixed-link")
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Signed-off-by: Lai Peter Jun Ann <peter.jun.ann.lai@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Provide phylink_expects_phy() to allow MAC drivers to check if it
is expecting a PHY to attach to. Since fixed-linked setups do not
need to attach to a PHY.
Provides a boolean value as to if the MAC should expect a PHY.
Returns true if a PHY is expected.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Syzbot reported a bug as following:
refcount_t: addition on 0; use-after-free.
...
RIP: 0010:refcount_warn_saturate+0x17c/0x1f0 lib/refcount.c:25
...
Call Trace:
<TASK>
__refcount_add include/linux/refcount.h:199 [inline]
__refcount_inc include/linux/refcount.h:250 [inline]
refcount_inc include/linux/refcount.h:267 [inline]
kref_get include/linux/kref.h:45 [inline]
qrtr_node_acquire net/qrtr/af_qrtr.c:202 [inline]
qrtr_node_lookup net/qrtr/af_qrtr.c:398 [inline]
qrtr_send_resume_tx net/qrtr/af_qrtr.c:1003 [inline]
qrtr_recvmsg+0x85f/0x990 net/qrtr/af_qrtr.c:1070
sock_recvmsg_nosec net/socket.c:1017 [inline]
sock_recvmsg+0xe2/0x160 net/socket.c:1038
qrtr_ns_worker+0x170/0x1700 net/qrtr/ns.c:688
process_one_work+0x991/0x15c0 kernel/workqueue.c:2390
worker_thread+0x669/0x1090 kernel/workqueue.c:2537
It occurs in the concurrent scenario of qrtr_recvmsg() and
qrtr_endpoint_unregister() as following:
cpu0 cpu1
qrtr_recvmsg qrtr_endpoint_unregister
qrtr_send_resume_tx qrtr_node_release
qrtr_node_lookup mutex_lock(&qrtr_node_lock)
spin_lock_irqsave(&qrtr_nodes_lock, ) refcount_dec_and_test(&node->ref) [node->ref == 0]
radix_tree_lookup [node != NULL] __qrtr_node_release
qrtr_node_acquire spin_lock_irqsave(&qrtr_nodes_lock, )
kref_get(&node->ref) [WARNING] ...
mutex_unlock(&qrtr_node_lock)
Use qrtr_node_lock to protect qrtr_node_lookup() implementation, this
is actually improving the protection of node reference.
Fixes: 0a7e0d0ef054 ("net: qrtr: Migrate node lookup tree to spinlock")
Reported-by: syzbot+a7492efaa5d61b51db23@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=a7492efaa5d61b51db23
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch sets the skb owner in the recv and send path for virtio.
For the send path, this solves the leak caused when
virtio_transport_purge_skbs() finds skb->sk is always NULL and therefore
never matches it with the current socket. Setting the owner upon
allocation fixes this.
For the recv path, this ensures correctness of accounting and also
correct transfer of ownership in vsock_loopback (when skbs are sent from
one socket and received by another).
Fixes: 71dc9ec9ac7d ("virtio/vsock: replace virtio_vsock_pkt with sk_buff")
Signed-off-by: Bobby Eshleman <bobby.eshleman@bytedance.com>
Reported-by: Cong Wang <xiyou.wangcong@gmail.com>
Link: https://lore.kernel.org/all/ZCCbATwov4U+GBUv@pop-os.localdomain/
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 7dd76d1feec70 ("dm: improve bio splitting and associated IO
accounting") only called setup_split_accounting() from
__send_duplicate_bios() if a single bio were being issued. But the case
where duplicate bios are issued must call it too.
Otherwise the bio won't be split and resubmitted (via recursion through
block core back to DM) to submit the later portions of a bio (which may
map to an entirely different target).
For example, when discarding an entire DM striped device with the
following DM table:
vg-lvol0: 0 159744 striped 2 128 7:0 2048 7:1 2048
vg-lvol0: 159744 45056 striped 2 128 7:2 2048 7:3 2048
Before (broken, discards the first striped target's devices twice):
device-mapper: striped: target_stripe=0, bdev=7:0, start=2048 len=79872
device-mapper: striped: target_stripe=1, bdev=7:1, start=2048 len=79872
device-mapper: striped: target_stripe=0, bdev=7:0, start=2049 len=22528
device-mapper: striped: target_stripe=1, bdev=7:1, start=2048 len=22528
After (works as expected):
device-mapper: striped: target_stripe=0, bdev=7:0, start=2048 len=79872
device-mapper: striped: target_stripe=1, bdev=7:1, start=2048 len=79872
device-mapper: striped: target_stripe=0, bdev=7:2, start=2048 len=22528
device-mapper: striped: target_stripe=1, bdev=7:3, start=2048 len=22528
Fixes: 7dd76d1feec70 ("dm: improve bio splitting and associated IO accounting")
Cc: stable@vger.kernel.org
Reported-by: Orange Kao <orange@aiven.io>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
|
|
"Abnormal" bios include discards, write zeroes and secure erase. By no
longer passing the calculated 'len' pointer, commit 7dd06a2548b2 ("dm:
allow dm_accept_partial_bio() for dm_io without duplicate bios") took a
senseless approach to disallowing dm_accept_partial_bio() from working
for duplicate bios processed using __send_duplicate_bios().
It inadvertently and incorrectly stopped the use of 'len' when
initializing a target's io (in alloc_tio). As such the resulting tio
could address more area of a device than it should.
For example, when discarding an entire DM striped device with the
following DM table:
vg-lvol0: 0 159744 striped 2 128 7:0 2048 7:1 2048
vg-lvol0: 159744 45056 striped 2 128 7:2 2048 7:3 2048
Before this fix:
device-mapper: striped: target_stripe=0, bdev=7:0, start=2048 len=102400
blkdiscard: attempt to access beyond end of device
loop0: rw=2051, sector=2048, nr_sectors = 102400 limit=81920
device-mapper: striped: target_stripe=1, bdev=7:1, start=2048 len=102400
blkdiscard: attempt to access beyond end of device
loop1: rw=2051, sector=2048, nr_sectors = 102400 limit=81920
After this fix;
device-mapper: striped: target_stripe=0, bdev=7:0, start=2048 len=79872
device-mapper: striped: target_stripe=1, bdev=7:1, start=2048 len=79872
Fixes: 7dd06a2548b2 ("dm: allow dm_accept_partial_bio() for dm_io without duplicate bios")
Cc: stable@vger.kernel.org
Reported-by: Orange Kao <orange@aiven.io>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
|
|
The cache needs to be flushed to ensure that the hardware stops offloading
the flow immediately.
Fixes: 33fc42de3327 ("net: ethernet: mtk_eth_soc: support creating mac address based offload entries")
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230330120840.52079-3-nbd@nbd.name
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Check for skb metadata in order to detect the case where the DSA header
is not present.
Fixes: 2d7605a72906 ("net: ethernet: mtk_eth_soc: enable hardware DSA untagging")
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230330120840.52079-2-nbd@nbd.name
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since we call flow_block_cb_decref on FLOW_BLOCK_UNBIND, we also need to
call flow_block_cb_incref for a newly allocated cb.
Also fix the accidentally inverted refcount check on unbind.
Fixes: 502e84e2382d ("net: ethernet: mtk_eth_soc: add flow offloading support")
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230330120840.52079-1-nbd@nbd.name
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Reported on the Turris forum, mvneta provokes kernel warnings in the
architecture DMA mapping code when mvneta_setup_txqs() fails to
allocate memory. This happens because when mvneta_cleanup_txqs() is
called in the mvneta_stop() path, we leave pointers in the structure
that have been freed.
Then on mvneta_open(), we call mvneta_setup_txqs(), which starts
allocating memory. On memory allocation failure, mvneta_cleanup_txqs()
will walk all the queues freeing any non-NULL pointers - which includes
pointers that were previously freed in mvneta_stop().
Fix this by setting these pointers to NULL to prevent double-freeing
of the same memory.
Fixes: 2adb719d74f6 ("net: mvneta: Implement software TSO")
Link: https://forum.turris.cz/t/random-kernel-exceptions-on-hbl-tos-7-0/18865/8
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1phUe5-00EieL-7q@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If certain conditions are met, DSA can install all necessary MAC
addresses on the CPU ports as FDB entries and disable flooding towards
the CPU (we call this RX filtering).
There is one corner case where this does not work.
ip link add br0 type bridge vlan_filtering 1 && ip link set br0 up
ip link set swp0 master br0 && ip link set swp0 up
ip link add link swp0 name swp0.100 type vlan id 100
ip link set swp0.100 up && ip addr add 192.168.100.1/24 dev swp0.100
Traffic through swp0.100 is broken, because the bridge turns on VLAN
filtering in the swp0 port (causing RX packets to be classified to the
FDB database corresponding to the VID from their 802.1Q header), and
although the 8021q module does call dev_uc_add() towards the real
device, that API is VLAN-unaware, so it only contains the MAC address,
not the VID; and DSA's current implementation of ndo_set_rx_mode() is
only for VID 0 (corresponding to FDB entries which are installed in an
FDB database which is only hit when the port is VLAN-unaware).
It's interesting to understand why the bridge does not turn on
IFF_PROMISC for its swp0 bridge port, and it may appear at first glance
that this is a regression caused by the logic in commit 2796d0c648c9
("bridge: Automatically manage port promiscuous mode."). After all,
a bridge port needs to have IFF_PROMISC by its very nature - it needs to
receive and forward frames with a MAC DA different from the bridge
ports' MAC addresses.
While that may be true, when the bridge is VLAN-aware *and* it has a
single port, there is no real reason to enable promiscuity even if that
is an automatic port, with flooding and learning (there is nowhere for
packets to go except to the BR_FDB_LOCAL entries), and this is how the
corner case appears. Adding a second automatic interface to the bridge
would make swp0 promisc as well, and would mask the corner case.
Given the dev_uc_add() / ndo_set_rx_mode() API is what it is (it doesn't
pass a VLAN ID), the only way to address that problem is to install host
FDB entries for the cartesian product of RX filtering MAC addresses and
VLAN RX filters.
Fixes: 7569459a52c9 ("net: dsa: manage flooding on the CPU ports")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230329151821.745752-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Do not set the MV88E6XXX_PORT_CTL0_IGMP_MLD_SNOOP bit on CPU or DSA ports.
This allows the host CPU port to be a regular IGMP listener by sending out
IGMP Membership Reports, which would otherwise not be forwarded by the
mv88exxx chip, but directly looped back to the CPU port itself.
Fixes: 54d792f257c6 ("net: dsa: Centralise global and port setup code into mv88e6xxx.")
Signed-off-by: Steffen Bätz <steffen@innosonix.de>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230329150140.701559-1-festevam@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit df622729ddbf as it introduces a use-after-free,
which isn't easy to fix without going back to the design drawing board.
Reported-by: Danilo Krummrich <dakr@redhat.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
|
|
This reverts commit 97804a133c68, as it builds on top of df622729ddbf
("drm/scheduler: track GPU active time per entity") which needs to be
reverted, as it introduces a use-after-free.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
|
|
drm_gem_prime_mmap() takes a reference on the GEM object, but before that
drm_gem_mmap_obj() already takes a reference, which will be leaked as only
one reference is dropped when the mapping is closed. Drop the extra
reference when dma_buf_mmap() succeeds.
Cc: stable@vger.kernel.org
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
|
|
Skip mode2 reset only for IMU enabled APUs when do S4.
This patch is to fix the regression issue
https://gitlab.freedesktop.org/drm/amd/-/issues/2483
It is generated by commit b589626674de ("drm/amdgpu: skip ASIC reset
for APUs when go to S4").
Fixes: b589626674de ("drm/amdgpu: skip ASIC reset for APUs when go to S4")
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2483
Tested-by: Yuan Perry <Perry.Yuan@amd.com>
Signed-off-by: Tim Huang <tim.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.1.x
|
|
Issue the same error message in case an illegal page boundary crossing
has been detected in both cases where this is tested.
Suggested-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Link: https://lore.kernel.org/r/20230329080259.14823-1-jgross@suse.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The call to invalidate_inode_pages2_range() in __iomap_dio_rw() may
fail, in which case -ENOTBLK is returned and this error code is
propagated back to user space trhough iomap_dio_rw() ->
zonefs_file_dio_write() return chain. This error code is fairly obscure
and may confuse the user. Avoid this and be consistent with the behavior
of zonefs_file_dio_append() for similar invalidate_inode_pages2_range()
errors by returning -EBUSY to user space when iomap_dio_rw() returns
-ENOTBLK.
Suggested-by: Christoph Hellwig <hch@infradead.org>
Fixes: 8dcc1a9d90c1 ("fs: New zonefs file system")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Tested-by: Hans Holmberg <hans.holmberg@wdc.com>
|
|
When a direct append write is executed, the append offset may correspond
to the last page of a sequential file inode which might have been cached
already by buffered reads, page faults with mmap-read or non-direct
readahead. To ensure that the on-disk and cached data is consistant for
such last cached page, make sure to always invalidate it in
zonefs_file_dio_append(). If the invalidation fails, return -EBUSY to
userspace to differentiate from IO errors.
This invalidation will always be a no-op when the FS block size (device
zone write granularity) is equal to the page size (e.g. 4K).
Reported-by: Hans Holmberg <Hans.Holmberg@wdc.com>
Fixes: 02ef12a663c7 ("zonefs: use REQ_OP_ZONE_APPEND for sync DIO")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Tested-by: Hans Holmberg <hans.holmberg@wdc.com>
|
|
Avoid potential data corruption issues caused by uninitialized driver
private data structures.
Reported-by: Brian Coverstone <brian@mainsequence.net>
Fixes: 6a9d1b91f34d ("mac80211: add pre-RCU-sync sta removal driver operation")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20230324120924.38412-3-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Adjust the network header to point at the correct payload offset
Fixes: 986e43b19ae9 ("wifi: mac80211: fix receiving A-MSDU frames on mesh interfaces")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20230324120924.38412-2-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Linearize packets (needed for forwarding A-MSDU subframes).
Fixes: 986e43b19ae9 ("wifi: mac80211: fix receiving A-MSDU frames on mesh interfaces")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20230324120924.38412-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When forwarding is set to 0, frames are typically sent with ttl=1.
Move the ttl decrement check below the check for local receive in order to
fix packet drops.
Reported-by: Thomas Hühn <thomas.huehn@hs-nordhausen.de>
Reported-by: Nick Hainke <vincent@systemli.org>
Fixes: 986e43b19ae9 ("wifi: mac80211: fix receiving A-MSDU frames on mesh interfaces")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20230326151709.17743-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Here should return the size of ieee80211_eht_cap_elem_fixed, so fix it.
Fixes: 820acc810fb6 ("mac80211: Add EHT capabilities to association/probe request")
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Link: https://lore.kernel.org/r/06c13635fc03bcff58a647b8e03e9f01a74294bd.1679935259.git.ryder.lee@mediatek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
rx->sta->amsdu_mesh_control is being passed to ieee80211_amsdu_to_8023s
without checking rx->sta. Since it doesn't make sense to accept A-MSDU
packets without a sta, simply add a check earlier.
Fixes: 6e4c0d0460bd ("wifi: mac80211: add a workaround for receiving non-standard mesh A-MSDU")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20230330090001.60750-2-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
These were unintentional copy&paste mistakes.
Cc: stable@vger.kernel.org
Fixes: 986e43b19ae9 ("wifi: mac80211: fix receiving A-MSDU frames on mesh interfaces")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20230330090001.60750-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This adds test which checks case when data of newly received skbuff is
appended to the last skbuff in the socket's queue. It looks like simple
test with 'send()' and 'recv()', but internally it triggers logic which
appends one received skbuff to another. Test checks that this feature
works correctly.
This test is actual only for virtio transport.
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This adds WARN_ONCE() and return from stream dequeue callback when
socket's queue is empty, but 'rx_bytes' still non-zero. This allows
the detection of potential bugs due to packet merging (see previous
patch).
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This fixes appending newly arrived skbuff to the last skbuff of the
socket's queue. Problem fires when we are trying to append data to skbuff
which was already processed in dequeue callback at least once. Dequeue
callback calls function 'skb_pull()' which changes 'skb->len'. In current
implementation 'skb->len' is used to update length in header of the last
skbuff after new data was copied to it. This is bug, because value in
header is used to calculate 'rx_bytes'/'fwd_cnt' and thus must be not
be changed during skbuff's lifetime.
Bug starts to fire since:
commit 077706165717
("virtio/vsock: don't use skbuff state to account credit")
It presents before, but didn't triggered due to a little bit buggy
implementation of credit calculation logic. So use Fixes tag for it.
Fixes: 077706165717 ("virtio/vsock: don't use skbuff state to account credit")
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
bnxt_fw_to_ethtool_speed() is missing the case statement for 200G
link speed reported by firmware. As a result, ethtool will report
unknown speed when the firmware reports 200G link speed.
Fixes: 532262ba3b84 ("bnxt_en: ethtool: support PAM4 link speeds up to 200G")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix 57502 and 57508 NPAR description string entries. The typos
caused these devices to not match up with lspci output.
Fixes: 49c98421e6ab ("bnxt_en: Add PCI IDs for 57500 series NPAR devices.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the selftest command fails, driver is not reporting the failure
by updating the "test->flags" when bnxt_close_nic() fails.
Fixes: eb51365846bc ("bnxt_en: Add basic ethtool -t selftest support.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix invalid registers dump from ethtool -d ethX after adapter self test
by ethtool -t ethY. It causes invalid data display.
The problem was caused by overwriting i40e_reg_list[].elements
which is common for ethtool self test and dump.
Fixes: 22dd9ae8afcc ("i40e: Rework register diagnostic")
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230328172659.3906413-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
build_skb() no longer accepts slab buffers. Since slab use is fairly
uncommon we prefer the drivers to call a separate slab_build_skb()
function appropriately.
bnx2x uses the old semantics where size of 0 meant buffer from slab.
It sets the fp->rx_frag_size to 0 for MTUs which don't fit in a page.
It needs to call slab_build_skb().
This fixes the WARN_ONCE() of incorrect API use seen with bnx2x.
Reported-by: Thomas Voegtle <tv@lio96.de>
Link: https://lore.kernel.org/all/b8f295e4-ba57-8bfb-7d9c-9d62a498a727@lio96.de/
Fixes: ce098da1497c ("skbuff: Introduce slab_build_skb()")
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230329000013.2734957-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In gsi_trans_pool_init_dma(), the total size of a pool of memory
used for DMA transactions is calculated. However the calculation is
done incorrectly.
For 4KB pages, this total size is currently always more than one
page, and as a result, the calculation produces a positive (though
incorrect) total size. The code still works in this case; we just
end up with fewer DMA pool entries than we intended.
Bjorn Andersson tested booting a kernel with 16KB pages, and hit a
null pointer derereference in sg_alloc_append_table_from_pages(),
descending from gsi_trans_pool_init_dma(). The cause of this was
that a 16KB total size was going to be allocated, and with 16KB
pages the order of that allocation is 0. The total_size calculation
yielded 0, which eventually led to the crash.
Correcting the total_size calculation fixes the problem.
Reported-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Tested-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Fixes: 9dd441e4ed57 ("soc: qcom: ipa: GSI transactions")
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230328162751.2861791-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
8b/10b encoding needs to add 3% fec overhead into the pbn.
In the Synapcis Cascaded MST hub, the first stage MST branch device
needs the information to determine the timeslot count for the
second stage MST branch device. Missing this overhead will leads to
insufficient timeslot allocation.
Cc: stable@vger.kernel.org
Cc: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Traditional synaptics hub has one MST branch device without virtual dpcd.
Synaptics cascaded hub has two chained MST branch devices. DSC decoding
is performed via root MST branch device, instead of the second MST branch
device.
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
The drm_buddy_test KUnit tests verify that returned blocks have sizes
which are powers of two using is_power_of_2(). However, is_power_of_2()
operations on a 'long', but the block size is a u64. So on systems where
long is 32-bit, this can sometimes fail even on correctly sized blocks.
This only reproduces randomly, as the parameters passed to the buddy
allocator in this test are random. The seed 0xb2e06022 reproduced it
fine here.
For now, just hardcode an is_power_of_2() implementation using
x & (x - 1).
Signed-off-by: David Gow <davidgow@google.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Arunpravin Paneer Selvam <arunpravin.paneerselvam@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230329065532.2122295-2-davidgow@google.com
Signed-off-by: Christian König <christian.koenig@amd.com>
|
|
The drm buddy allocator tests were broken on 32-bit systems, as
rounddown_pow_of_two() takes a long, and the buddy allocator handles
64-bit sizes even on 32-bit systems.
This can be reproduced with the drm_buddy_allocator KUnit tests on i386:
./tools/testing/kunit/kunit.py run --arch i386 \
--kunitconfig ./drivers/gpu/drm/tests drm_buddy
(It results in kernel BUG_ON() when too many blocks are created, due to
the block size being too small.)
This was independently uncovered (and fixed) by Luís Mendes, whose patch
added a new u64 variant of rounddown_pow_of_two(). This version instead
recalculates the size based on the order.
Reported-by: Luís Mendes <luis.p.mendes@gmail.com>
Link: https://lore.kernel.org/lkml/CAEzXK1oghXAB_KpKpm=-CviDQbNaH0qfgYTSSjZgvvyj4U78AA@mail.gmail.com/T/
Signed-off-by: David Gow <davidgow@google.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Arunpravin Paneer Selvam <arunpravin.paneerselvam@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230329065532.2122295-1-davidgow@google.com
Signed-off-by: Christian König <christian.koenig@amd.com>
|
|
Fix headset microphone detection on Lenovo ZhaoYang CF4620Z.
[ adjusted to be applicable to the latest tree -- tiwai ]
Signed-off-by: huangwenhui <huangwenhuia@uniontech.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230328074644.30142-1-huangwenhuia@uniontech.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
Felix Fietkau
Gustav Ekelund
Jakub Kicinski
Eric Dumazet
Arseniy Krasnov
Jiri Slaby (SUSE)
Arnd Bergmann
Andrea Righi
Michael Sit Wei Hong
Ziyang Xuan
Bobby Eshleman
Mike Snitzer
Russell King (Oracle)
Vladimir Oltean
Steffen Bätz
Lucas Stach
Tim Huang
Juergen Gross
Damien Le Moal
Ryder Lee
Michael Chan
Kalesh AP
Radoslaw Tyl
Alex Elder
Fangzhi Zuo
David Gow
huangwenhui