| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Commit 8a23eb804ca4 ("Make filldir[64]() verify the directory entry
filename is valid") added some minimal validity checks on the directory
entries passed to filldir[64](). But they really were pretty minimal.
This fleshes out at least the name length check: we used to disallow
zero-length names, but really, negative lengths or oevr-long names
aren't ok either. Both could happen if there is some filesystem
corruption going on.
Now, most filesystems tend to use just an "unsigned char" or similar for
the length of a directory entry name, so even with a corrupt filesystem
you should never see anything odd like that. But since we then use the
name length to create the directory entry record length, let's make sure
it actually is half-way sensible.
Note how POSIX states that the size of a path component is limited by
NAME_MAX, but we actually use PATH_MAX for the check here. That's
because while NAME_MAX is generally the correct maximum name length
(it's 255, for the same old "name length is usually just a byte on
disk"), there's nothing in the VFS layer that really cares.
So the real limitation at a VFS layer is the total pathname length you
can pass as a filename: PATH_MAX.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add pointer to datasheet and fix typo in printk message.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
Trivial cleanup removing empty line at wrong place.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
Apparently it is quite easy to forget ">" in quoting of email
address. This fixes it.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
We need the of_match table if we want to use the compatible string in
the pmic's child node and get the led driver loaded automatically.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
If a node is ignored, do not get a reference to it. Fix the bug by moving
fwnode_handle_get() where a reference to an fwnode is saved for clarity.
Reported-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
When switching to using generic LED name composition mechanism via
devm_led_classdev_register_ext() API the part of code initializing
struct gpio_led's template name property was removed alongside.
It was however overlooked that the property was also passed to
devm_fwnode_get_gpiod_from_child() in place of "label" parameter,
which when set to NULL, results in gpio label being initialized to '?'.
It could be observed in debugfs and failed to properly identify
gpio association with LED consumer.
Fix this shortcoming by updating the GPIO label after the LED is
registered and its final name is known.
Fixes: d7235f5feaa0 ("leds: gpio: Use generic support for composing LED names")
Cc: Russell King <linux@armlinux.org.uk>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
[fixed comment]
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
Commit 99c9a923e97a ("tracing/uprobe: Fix double perf_event
linking on multiprobe uprobe") moved trace_uprobe_filter on
trace_probe_event. However, since it introduced a flexible
data structure with char array and type casting, the
alignment of trace_uprobe_filter can be broken.
This changes the type of the array to trace_uprobe_filter
data strucure to fix it.
Link: http://lore.kernel.org/r/20200120124022.GA14897@hirez.programming.kicks-ass.net
Link: http://lkml.kernel.org/r/157966340499.5107.10978352478952144902.stgit@devnote2
Fixes: 99c9a923e97a ("tracing/uprobe: Fix double perf_event linking on multiprobe uprobe")
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
Currently, we just assume that it will stick around by virtue of the
submitter's reference, but later patches will allow the syscall to
return early and we can't rely on that reference at that point.
While I'm not aware of any reports of it, Xiubo pointed out that this
may fix a use-after-free. If the wait for a reply times out or is
canceled via signal, and then the reply comes in after the syscall
returns, the client can end up trying to access r_parent without a
reference.
Take an extra reference to the inode when setting r_parent and release
it when releasing the request.
Cc: stable@vger.kernel.org
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
fds field of struct io_uring_files_update is problematic with regards
to compat user space, as pointer size is different in 32-bit, 32-on-64-bit,
and 64-bit user space. In order to avoid custom handling of compat in
the syscall implementation, make fds __u64 and use u64_to_user_ptr in
order to retrieve it. Also, align the field naturally and check that
no garbage is passed there.
Fixes: c3a31e605620c279 ("io_uring: add support for IORING_REGISTER_FILES_UPDATE")
Signed-off-by: Eugene Syromiatnikov <esyr@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When trace_clock option is not set and unstable clcok detected,
tracing_set_default_clock() sets trace_clock(ThinkPad A285 is one of
case). In that case, if lockdown is in effect, null pointer
dereference error happens in ring_buffer_set_clock().
Link: http://lkml.kernel.org/r/20200116131236.3866925-1-masami256@gmail.com
Cc: stable@vger.kernel.org
Fixes: 17911ff38aa58 ("tracing: Add locked_down checks to the open calls of files created for tracefs")
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1788488
Signed-off-by: Masami Ichikawa <masami256@gmail.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
While working on a tool to convert SQL syntex into the histogram language of
the kernel, I discovered the following bug:
# echo 'first u64 start_time u64 end_time pid_t pid u64 delta' >> synthetic_events
# echo 'hist:keys=pid:start=common_timestamp' > events/sched/sched_waking/trigger
# echo 'hist:keys=next_pid:delta=common_timestamp-$start,start2=$start:onmatch(sched.sched_waking).trace(first,$start2,common_timestamp,next_pid,$delta)' > events/sched/sched_switch/trigger
Would not display any histograms in the sched_switch histogram side.
But if I were to swap the location of
"delta=common_timestamp-$start" with "start2=$start"
Such that the last line had:
# echo 'hist:keys=next_pid:start2=$start,delta=common_timestamp-$start:onmatch(sched.sched_waking).trace(first,$start2,common_timestamp,next_pid,$delta)' > events/sched/sched_switch/trigger
The histogram works as expected.
What I found out is that the expressions clear out the value once it is
resolved. As the variables are resolved in the order listed, when
processing:
delta=common_timestamp-$start
The $start is cleared. When it gets to "start2=$start", it errors out with
"unresolved symbol" (which is silent as this happens at the location of the
trace), and the histogram is dropped.
When processing the histogram for variable references, instead of adding a
new reference for a variable used twice, use the same reference. That way,
not only is it more efficient, but the order will no longer matter in
processing of the variables.
From Tom Zanussi:
"Just to clarify some more about what the problem was is that without
your patch, we would have two separate references to the same variable,
and during resolve_var_refs(), they'd both want to be resolved
separately, so in this case, since the first reference to start wasn't
part of an expression, it wouldn't get the read-once flag set, so would
be read normally, and then the second reference would do the read-once
read and also be read but using read-once. So everything worked and
you didn't see a problem:
from: start2=$start,delta=common_timestamp-$start
In the second case, when you switched them around, the first reference
would be resolved by doing the read-once, and following that the second
reference would try to resolve and see that the variable had already
been read, so failed as unset, which caused it to short-circuit out and
not do the trigger action to generate the synthetic event:
to: delta=common_timestamp-$start,start2=$start
With your patch, we only have the single resolution which happens
correctly the one time it's resolved, so this can't happen."
Link: https://lore.kernel.org/r/20200116154216.58ca08eb@gandalf.local.home
Cc: stable@vger.kernel.org
Fixes: 067fe038e70f6 ("tracing: Add variable reference handling to hist triggers")
Reviewed-by: Tom Zanuss <zanussi@kernel.org>
Tested-by: Tom Zanussi <zanussi@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
|
|
A queue can't belong to multiple traffic classes. So, reject
any such configuration that results in overlapped queues for a
traffic class.
Fixes: b1396c2bd675 ("cxgb4: parse and configure TC-MQPRIO offload")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
T6 can support 2 egress traffic management channels per port to
double the total number of traffic classes that can be configured.
In this configuration, if the class belongs to the other channel,
then all the queues must be bound again explicitly to the new class,
for the rate limit parameters on the other channel to take effect.
So, always explicitly bind all queues to the port rate limit traffic
class, regardless of the traffic management channel that it belongs
to. Also, only bind queues to port rate limit traffic class, if all
the queues don't already belong to an existing different traffic
class.
Fixes: 4ec4762d8ec6 ("cxgb4: add TC-MATCHALL classifier egress offload")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement a cleanup method to properly free ci->params
BUG: memory leak
unreferenced object 0xffff88811746e2c0 (size 64):
comm "syz-executor617", pid 7106, jiffies 4294943055 (age 14.250s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
c0 34 60 84 ff ff ff ff 00 00 00 00 00 00 00 00 .4`.............
backtrace:
[<0000000015aa236f>] kmemleak_alloc_recursive include/linux/kmemleak.h:43 [inline]
[<0000000015aa236f>] slab_post_alloc_hook mm/slab.h:586 [inline]
[<0000000015aa236f>] slab_alloc mm/slab.c:3320 [inline]
[<0000000015aa236f>] kmem_cache_alloc_trace+0x145/0x2c0 mm/slab.c:3549
[<000000002c946bd1>] kmalloc include/linux/slab.h:556 [inline]
[<000000002c946bd1>] kzalloc include/linux/slab.h:670 [inline]
[<000000002c946bd1>] tcf_ctinfo_init+0x21a/0x530 net/sched/act_ctinfo.c:236
[<0000000086952cca>] tcf_action_init_1+0x400/0x5b0 net/sched/act_api.c:944
[<000000005ab29bf8>] tcf_action_init+0x135/0x1c0 net/sched/act_api.c:1000
[<00000000392f56f9>] tcf_action_add+0x9a/0x200 net/sched/act_api.c:1410
[<0000000088f3c5dd>] tc_ctl_action+0x14d/0x1bb net/sched/act_api.c:1465
[<000000006b39d986>] rtnetlink_rcv_msg+0x178/0x4b0 net/core/rtnetlink.c:5424
[<00000000fd6ecace>] netlink_rcv_skb+0x61/0x170 net/netlink/af_netlink.c:2477
[<0000000047493d02>] rtnetlink_rcv+0x1d/0x30 net/core/rtnetlink.c:5442
[<00000000bdcf8286>] netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline]
[<00000000bdcf8286>] netlink_unicast+0x223/0x310 net/netlink/af_netlink.c:1328
[<00000000fc5b92d9>] netlink_sendmsg+0x2c0/0x570 net/netlink/af_netlink.c:1917
[<00000000da84d076>] sock_sendmsg_nosec net/socket.c:639 [inline]
[<00000000da84d076>] sock_sendmsg+0x54/0x70 net/socket.c:659
[<0000000042fb2eee>] ____sys_sendmsg+0x2d0/0x300 net/socket.c:2330
[<000000008f23f67e>] ___sys_sendmsg+0x8a/0xd0 net/socket.c:2384
[<00000000d838e4f6>] __sys_sendmsg+0x80/0xf0 net/socket.c:2417
[<00000000289a9cb1>] __do_sys_sendmsg net/socket.c:2426 [inline]
[<00000000289a9cb1>] __se_sys_sendmsg net/socket.c:2424 [inline]
[<00000000289a9cb1>] __x64_sys_sendmsg+0x23/0x30 net/socket.c:2424
Fixes: 24ec483cec98 ("net: sched: Introduce act_ctinfo action")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Kevin 'ldir' Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Kevin 'ldir' Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The existing __lshrti3 was really inefficient, and the other two helpers
are also needed to compile some modules.
Add the missing versions, and export all of the symbols like arm64
already does.
This code is based on the assembly generated by libgcc builds.
This fixes a build break triggered by ubsan:
riscv64-unknown-linux-gnu-ld: lib/ubsan.o: in function `.L2':
ubsan.c:(.text.unlikely+0x38): undefined reference to `__ashlti3'
riscv64-unknown-linux-gnu-ld: ubsan.c:(.text.unlikely+0x42): undefined reference to `__ashrti3'
Signed-off-by: Olof Johansson <olof@lixom.net>
[paul.walmsley@sifive.com: use SYM_FUNC_{START,END} instead of
ENTRY/ENDPROC; note libgcc origin]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
Temporary files used in the VDSO build process linger on even after make
mrproper: vdso-dummy.o.tmp, vdso.so.dbg.tmp.
Delete them once they're no longer needed.
Signed-off-by: Ilie Halip <ilie.halip@gmail.com>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
DSN read can fail, for example on a kdump kernel without PCIe extended
config space support. If DSN read fails, don't set the
BNXT_FLAG_DSN_VALID flag and continue loading. Check the flag
to see if the stored DSN is valid before using it. Only VF reps
creation should fail without valid DSN.
Fixes: 03213a996531 ("bnxt: move bp->switch_id initialization to PF probe")
Reported-by: Marc Smith <msmith626@gmail.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix bnxt_fltr_match() to match ipv6 source and destination addresses.
The function currently only checks ipv4 addresses and will not work
corrently on ipv6 filters.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The NTUPLE related firmware commands are sent to the wrong firmware
channel, causing all these commands to fail on new firmware that
supports the new firmware channel. Fix it by excluding the 3
NTUPLE firmware commands from the list for the new firmware channel.
Fixes: 760b6d33410c ("bnxt_en: Add support for 2nd firmware message channel.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 69f594a38967 ("ptrace: do not audit capability check when outputing /proc/pid/stat")
introduced the ability to opt out of audit messages for accesses to various
proc files since they are not violations of policy. While doing so it
somehow switched the check from ns_capable() to
has_ns_capability{_noaudit}(). That means it switched from checking the
subjective credentials of the task to using the objective credentials. This
is wrong since. ptrace_has_cap() is currently only used in
ptrace_may_access() And is used to check whether the calling task (subject)
has the CAP_SYS_PTRACE capability in the provided user namespace to operate
on the target task (object). According to the cred.h comments this would
mean the subjective credentials of the calling task need to be used.
This switches ptrace_has_cap() to use security_capable(). Because we only
call ptrace_has_cap() in ptrace_may_access() and in there we already have a
stable reference to the calling task's creds under rcu_read_lock() there's
no need to go through another series of dereferences and rcu locking done
in ns_capable{_noaudit}().
As one example where this might be particularly problematic, Jann pointed
out that in combination with the upcoming IORING_OP_OPENAT feature, this
bug might allow unprivileged users to bypass the capability checks while
asynchronously opening files like /proc/*/mem, because the capability
checks for this would be performed against kernel credentials.
To illustrate on the former point about this being exploitable: When
io_uring creates a new context it records the subjective credentials of the
caller. Later on, when it starts to do work it creates a kernel thread and
registers a callback. The callback runs with kernel creds for
ktask->real_cred and ktask->cred. To prevent this from becoming a
full-blown 0-day io_uring will call override_cred() and override
ktask->cred with the subjective credentials of the creator of the io_uring
instance. With ptrace_has_cap() currently looking at ktask->real_cred this
override will be ineffective and the caller will be able to open arbitray
proc files as mentioned above.
Luckily, this is currently not exploitable but will turn into a 0-day once
IORING_OP_OPENAT{2} land in v5.6. Fix it now!
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Eric Paris <eparis@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Serge Hallyn <serge@hallyn.com>
Reviewed-by: Jann Horn <jannh@google.com>
Fixes: 69f594a38967 ("ptrace: do not audit capability check when outputing /proc/pid/stat")
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
|
|
As we reset the GPMI block at resume, the timing parameters setup by a
previous exec_op is lost. Rewriting GPMI timing registers on first exec_op
after resume fixes the problem.
Fixes: ef347c0cfd61 ("mtd: rawnand: gpmi: Implement exec_op")
Cc: stable@vger.kernel.org
Signed-off-by: Esben Haabendal <esben@geanix.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
On system resume, the gpmi clock must be enabled before accessing gpmi
block. Without this, resume causes something like
[ 661.348790] gpmi_reset_block(5cbb0f7e): module reset timeout
[ 661.348889] gpmi-nand 1806000.gpmi-nand: Error setting GPMI : -110
[ 661.348928] PM: dpm_run_callback(): platform_pm_resume+0x0/0x44 returns -110
[ 661.348961] PM: Device 1806000.gpmi-nand failed to resume: error -110
Fixes: ef347c0cfd61 ("mtd: rawnand: gpmi: Implement exec_op")
Cc: stable@vger.kernel.org
Signed-off-by: Esben Haabendal <esben@geanix.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The commit 7b678c69c0ca ("mtd: spi-nor: Merge spansion Quad Enable
methods") forgot to actually set the QE bit in some cases. Thus this
breaks quad mode accesses to flashes which support readback of the
status register-2. Fix it.
Fixes: 7b678c69c0ca ("mtd: spi-nor: Merge spansion Quad Enable methods")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
mtd->size is still unassigned when running spansion_post_sfdp_fixups()
hook, therefore use nor->params.size to determine the size of flash device.
This makes sure that 4-byte addressing opcodes are used on Spansion
flashes that are larger than 16MiB and don't have SFDP 4BAIT table
populated.
Fixes: 92094ebc385e ("mtd: spi-nor: Add spansion_post_sfdp_fixups()")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The hwmon core uses device managed functions, tied to the hwmon parent
device, for various internal memory allocations. This is problematic
since hwmon device lifetime does not necessarily match its parent's
device lifetime. If there is a mismatch, memory leaks will accumulate
until the parent device is released.
Fix the problem by managing all memory allocations internally. The only
exception is memory allocation for thermal device registration, which
can be tied to the hwmon device, along with thermal device registration
itself.
Fixes: d560168b5d0f ("hwmon: (core) New hwmon registration API")
Cc: stable@vger.kernel.org # v4.14.x: 47c332deb8e8: hwmon: Deal with errors from the thermal subsystem
Cc: stable@vger.kernel.org # v4.14.x: 74e3512731bd: hwmon: (core) Fix double-free in __hwmon_device_register()
Cc: stable@vger.kernel.org # v4.9.x: 3a412d5e4a1c: hwmon: (core) Simplify sysfs attribute name allocation
Cc: stable@vger.kernel.org # v4.9.x: 47c332deb8e8: hwmon: Deal with errors from the thermal subsystem
Cc: stable@vger.kernel.org # v4.9.x: 74e3512731bd: hwmon: (core) Fix double-free in __hwmon_device_register()
Cc: stable@vger.kernel.org # v4.9+
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
reg2volt returns the voltage that matches a given register value.
Converting this back the other way with volt2reg didn't return the same
register value because it used truncation instead of rounding.
This meant that values read from sysfs could not be written back to sysfs
to set back the same register value.
With this change, volt2reg will return the same value for every voltage
previously returned by reg2volt (for the set of possible input values)
Signed-off-by: Luuk Paulussen <luuk.paulussen@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20191205231659.1301-1-luuk.paulussen@alliedtelesis.co.nz
cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
No alarm is reported by /sys/.../inX_alarm
In detail:
The SMI Voltage status register is the only register giving a status
for voltages, but it does not work like the non-SMI status registers
used for temperatures and fans.
A bit is set for each input crossing a threshold, in both direction,
but the "inside" or "outside" limits info is not available.
Also this register is cleared on read.
Note : this is not explicitly spelled out in the datasheet, but from
experiment.
As a result if an input is crossing a threshold (min or max in any
direction), the alarm is reported only once even if the input is
still outside limits. Also if the alarm for another input is read
before the one of this input, no alarm is reported at all.
Signed-off-by: Gilles Buloz <gilles.buloz@kontron.com>
Link: https://lore.kernel.org/r/5de0f566.tBga5POKAgHlmd0p%gilles.buloz@kontron.com
Fixes: 3434f3783580 ("hwmon: Driver for Nuvoton NCT7802Y")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
in0 thresholds are written to the in2 thresholds registers
in2 thresholds to in3 thresholds
in3 thresholds to in4 thresholds
in4 thresholds to in0 thresholds
Signed-off-by: Gilles Buloz <gilles.buloz@kontron.com>
Link: https://lore.kernel.org/r/5de0f509.rc0oEvPOMjbfPW1w%gilles.buloz@kontron.com
Fixes: 3434f3783580 ("hwmon: Driver for Nuvoton NCT7802Y")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Check for NULL port data in the modem- and line-status handlers to avoid
dereferencing a NULL pointer in the unlikely case where a port device
isn't bound to a driver (e.g. after an allocation failure on port
probe).
Note that the other (stubbed) event handlers qt2_process_xmit_empty()
and qt2_process_flush() would need similar sanity checks in case they
are ever implemented.
Fixes: f7a33e608d9a ("USB: serial: add quatech2 usb to serial driver")
Cc: stable <stable@vger.kernel.org> # 3.5
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Check for NULL port data in the control URB completion handlers to avoid
dereferencing a NULL pointer in the unlikely case where a port device
isn't bound to a driver (e.g. after an allocation failure on port
probe()).
Fixes: 0ca1268e109a ("USB Serial Keyspan: add support for USA-49WG & USA-28XG")
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The driver receives the active port number from the device, but never
made sure that the port number was valid. This could lead to a
NULL-pointer dereference or memory corruption in case a device sends
data for an invalid port.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Check for NULL port data in the shared interrupt and bulk completion
callbacks to avoid dereferencing a NULL pointer in case a device sends
data for a port device which isn't bound to a driver (e.g. due to a
malicious device having unexpected endpoints or after an allocation
failure on port probe).
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Check for NULL port data in reset_resume() to avoid dereferencing a NULL
pointer in case the port device isn't bound to a driver (e.g. after a
failed control request at port probe).
Fixes: 1ded7ea47b88 ("USB: ch341 serial: fix port number changed after resume")
Cc: stable <stable@vger.kernel.org> # 2.6.30
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The fstest btrfs/154 reports
[ 8675.381709] BTRFS: Transaction aborted (error -28)
[ 8675.383302] WARNING: CPU: 1 PID: 31900 at fs/btrfs/block-group.c:2038 btrfs_create_pending_block_groups+0x1e0/0x1f0 [btrfs]
[ 8675.390925] CPU: 1 PID: 31900 Comm: btrfs Not tainted 5.5.0-rc6-default+ #935
[ 8675.392780] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59-gc9ba527-rebuilt.opensuse.org 04/01/2014
[ 8675.395452] RIP: 0010:btrfs_create_pending_block_groups+0x1e0/0x1f0 [btrfs]
[ 8675.402672] RSP: 0018:ffffb2090888fb00 EFLAGS: 00010286
[ 8675.404413] RAX: 0000000000000000 RBX: ffff92026dfa91c8 RCX: 0000000000000001
[ 8675.406609] RDX: 0000000000000000 RSI: ffffffff8e100899 RDI: ffffffff8e100971
[ 8675.408775] RBP: ffff920247c61660 R08: 0000000000000000 R09: 0000000000000000
[ 8675.410978] R10: 0000000000000000 R11: 0000000000000000 R12: 00000000ffffffe4
[ 8675.412647] R13: ffff92026db74000 R14: ffff920247c616b8 R15: ffff92026dfbc000
[ 8675.413994] FS: 00007fd5e57248c0(0000) GS:ffff92027d800000(0000) knlGS:0000000000000000
[ 8675.416146] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 8675.417833] CR2: 0000564aa51682d8 CR3: 000000006dcbc004 CR4: 0000000000160ee0
[ 8675.419801] Call Trace:
[ 8675.420742] btrfs_start_dirty_block_groups+0x355/0x480 [btrfs]
[ 8675.422600] btrfs_commit_transaction+0xc8/0xaf0 [btrfs]
[ 8675.424335] reset_balance_state+0x14a/0x190 [btrfs]
[ 8675.425824] btrfs_balance.cold+0xe7/0x154 [btrfs]
[ 8675.427313] ? kmem_cache_alloc_trace+0x235/0x2c0
[ 8675.428663] btrfs_ioctl_balance+0x298/0x350 [btrfs]
[ 8675.430285] btrfs_ioctl+0x466/0x2550 [btrfs]
[ 8675.431788] ? mem_cgroup_charge_statistics+0x51/0xf0
[ 8675.433487] ? mem_cgroup_commit_charge+0x56/0x400
[ 8675.435122] ? do_raw_spin_unlock+0x4b/0xc0
[ 8675.436618] ? _raw_spin_unlock+0x1f/0x30
[ 8675.438093] ? __handle_mm_fault+0x499/0x740
[ 8675.439619] ? do_vfs_ioctl+0x56e/0x770
[ 8675.441034] do_vfs_ioctl+0x56e/0x770
[ 8675.442411] ksys_ioctl+0x3a/0x70
[ 8675.443718] ? trace_hardirqs_off_thunk+0x1a/0x1c
[ 8675.445333] __x64_sys_ioctl+0x16/0x20
[ 8675.446705] do_syscall_64+0x50/0x210
[ 8675.448059] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 8675.479187] BTRFS: error (device vdb) in btrfs_create_pending_block_groups:2038: errno=-28 No space left
We now use btrfs_can_overcommit() to see if we can flip a block group
read only. Before this would fail because we weren't taking into
account the usable un-allocated space for allocating chunks. With my
patches we were allowed to do the balance, which is technically correct.
The test is trying to start balance on degraded mount. So now we're
trying to allocate a chunk and cannot because we want to allocate a
RAID1 chunk, but there's only 1 device that's available for usage. This
results in an ENOSPC.
But we shouldn't even be making it this far, we don't have enough
devices to restripe. The problem is we're using btrfs_num_devices(),
that also includes missing devices. That's not actually what we want, we
need to use rw_devices.
The chunk_mutex is not needed here, rw_devices changes only in device
add, remove or replace, all are excluded by EXCL_OP mechanism.
Fixes: e4d8ec0f65b9 ("Btrfs: implement online profile changing")
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ add stacktrace, update changelog, drop chunk_mutex ]
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
If scrub returns an error we are not copying back the scrub arguments
structure to user space. This prevents user space to know how much
progress scrub has done if an error happened - this includes -ECANCELED
which is returned when users ask for scrub to stop. A particular use
case, which is used in btrfs-progs, is to resume scrub after it is
canceled, in that case it relies on checking the progress from the scrub
arguments structure and then use that progress in a call to resume
scrub.
So fix this by always copying the scrub arguments structure to user
space, overwriting the value returned to user space with -EFAULT only if
copying the structure failed to let user space know that either that
copying did not happen, and therefore the structure is stale, or it
happened partially and the structure is probably not valid and corrupt
due to the partial copy.
Reported-by: Graham Cobb <g.btrfs@cobb.uk.net>
Link: https://lore.kernel.org/linux-btrfs/d0a97688-78be-08de-ca7d-bcb4c7fb397e@cobb.uk.net/
Fixes: 06fe39ab15a6a4 ("Btrfs: do not overwrite scrub error with fault error in scrub ioctl")
CC: stable@vger.kernel.org # 5.1+
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Tested-by: Graham Cobb <g.btrfs@cobb.uk.net>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
We would not be transmitting using the correct SYSTEMPORT transmit queue
during ndo_select_queue() which looks up the internal TX ring map
because while establishing the mapping we would be off by 4, so for
instance, when we populate switch port mappings we would be doing:
switch port 0, queue 0 -> ring index #0
switch port 0, queue 1 -> ring index #1
...
switch port 0, queue 3 -> ring index #3
switch port 1, queue 0 -> ring index #8 (4 + 4 * 1)
...
instead of using ring index #4. This would cause our ndo_select_queue()
to use the fallback queue mechanism which would pick up an incorrect
ring for that switch port. Fix this by using the correct switch queue
number instead of SYSTEMPORT queue number.
Fixes: 25c440704661 ("net: systemport: Simplify queue mapping logic")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the implementation of the system reset controller we lost a setting
that is currently applied by the bootloader and which configures the IMP
port for 2Gb/sec, the default is 1Gb/sec. This is needed given the
number of ports and applications we expect to run so bring back that
setting.
Fixes: 01b0ac07589e ("net: dsa: bcm_sf2: Add support for optional reset controller line")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The sja1105_parse_ports_node function was tested only on device trees
where all ports were enabled. Fix this check so that the driver
continues to probe only with the ports where status is not "disabled",
as expected.
Fixes: 8aa9ebccae87 ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to the Datasheet this bit should be 0 (Normal operation) in
default. With the FORCE_LINK_GOOD bit set, it is not possible to get a
link. This patch sets FORCE_LINK_GOOD to the default value after
resetting the phy.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PCIe Root Port driver for CPU Complex PCIe Root Ports are not
loaded on SNR.
The device ID for SNR PCIe3 unit is used by both uncore driver and the
PCIe Root Port driver. If uncore driver is loaded, the PCIe Root Port
driver never be probed.
Remove the PCIe3 unit for SNR for now. The support for PCIe3 unit will
be added later separately.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/20200116200210.18937-2-kan.liang@linux.intel.com
|
|
An Oops during the boot is found on some SNR machines. It turns out
this is because the snr_uncore_imc_freerunning_events[] array was
missing an end-marker.
Fixes: ee49532b38dd ("perf/x86/intel/uncore: Add IMC uncore support for Snow Ridge")
Reported-by: Like Xu <like.xu@linux.intel.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Like Xu <like.xu@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20200116200210.18937-1-kan.liang@linux.intel.com
|
|
The IMC uncore support is missed for E3-1585 v5 CPU.
Intel Xeon E3 V5 Family has Sky Lake CPU.
Add the PCI ID of IMC for Intel Xeon E3 V5 Family.
Reported-by: Rosales-fernandez, Carlos <carlos.rosales-fernandez@intel.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Rosales-fernandez, Carlos <carlos.rosales-fernandez@intel.com>
Link: https://lkml.kernel.org/r/1578687311-158748-1-git-send-email-kan.liang@linux.intel.com
|
|
Vince reports a worrying issue:
| so I was tracking down some odd behavior in the perf_fuzzer which turns
| out to be because perf_even_open() sometimes returns 0 (indicating a file
| descriptor of 0) even though as far as I can tell stdin is still open.
... and further the cause:
| error is triggered if aux_sample_size has non-zero value.
|
| seems to be this line in kernel/events/core.c:
|
| if (perf_need_aux_event(event) && !perf_get_aux_event(event, group_leader))
| goto err_locked;
|
| (note, err is never set)
This seems to be a thinko in commit:
ab43762ef010967e ("perf: Allow normal events to output AUX data")
... and we should probably return -EINVAL here, as this should only
happen when the new event is mis-configured or does not have a
compatible aux_event group leader.
Fixes: ab43762ef010967e ("perf: Allow normal events to output AUX data")
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Tested-by: Vince Weaver <vincent.weaver@maine.edu>
|
|
When there is not enough memory and napi_alloc_skb() return NULL,
the HNS driver will print error message, and than try again, if
the memory is not enough for a while, huge error message and the
retry operation will cause soft lockup.
When napi_alloc_skb() return NULL because of no memory, we can
get a warn_alloc() call trace, so this patch deletes the error
message. We already use polling mode to handle irq, but the
retry operation will render the polling weight inactive, this
patch just return budget when the rx is not completed to avoid
dead loop.
Fixes: 36eedfde1a36 ("net: hns: Optimize hns_nic_common_poll for better performance")
Fixes: b5996f11ea54 ("net: add Hisilicon Network Subsystem basic ethernet support")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
USB-serial drivers must not be unbound from their ports before the
corresponding USB driver is unbound from the parent interface so
suppress the bind and unbind attributes.
Unbinding a serial driver while it's port is open is a sure way to
trigger a crash as any driver state is released on unbind while port
hangup is handled on the parent USB interface level. Drivers for
multiport devices where ports share a resource such as an interrupt
endpoint also generally cannot handle individual ports going away.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
syzbot reported some bogus lockdep warnings, for example bad unlock
balance in sch_direct_xmit(). They are due to a race condition between
slow path and fast path, that is qdisc_xmit_lock_key gets re-registered
in netdev_update_lockdep_key() on slow path, while we could still
acquire the queue->_xmit_lock on fast path in this small window:
CPU A CPU B
__netif_tx_lock();
lockdep_unregister_key(qdisc_xmit_lock_key);
__netif_tx_unlock();
lockdep_register_key(qdisc_xmit_lock_key);
In fact, unlike the addr_list_lock which has to be reordered when
the master/slave device relationship changes, queue->_xmit_lock is
only acquired on fast path and only when NETIF_F_LLTX is not set,
so there is likely no nested locking for it.
Therefore, we can just get rid of re-registration of
qdisc_xmit_lock_key.
Reported-by: syzbot+4ec99438ed7450da6272@syzkaller.appspotmail.com
Fixes: ab92d68fc22f ("net: core: add generic lockdep keys")
Cc: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It seems better to init ife->metalist earlier in tcf_ife_init()
to avoid the following crash :
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 10483 Comm: syz-executor216 Not tainted 5.5.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:_tcf_ife_cleanup net/sched/act_ife.c:412 [inline]
RIP: 0010:tcf_ife_cleanup+0x6e/0x400 net/sched/act_ife.c:431
Code: 48 c1 ea 03 80 3c 02 00 0f 85 94 03 00 00 49 8b bd f8 00 00 00 48 b8 00 00 00 00 00 fc ff df 4c 8d 67 e8 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 5c 03 00 00 48 bb 00 00 00 00 00 fc ff df 48 8b
RSP: 0018:ffffc90001dc6d00 EFLAGS: 00010246
RAX: dffffc0000000000 RBX: ffffffff864619c0 RCX: ffffffff815bfa09
RDX: 0000000000000000 RSI: 0000000000000004 RDI: 0000000000000000
RBP: ffffc90001dc6d50 R08: 0000000000000004 R09: fffff520003b8d8e
R10: fffff520003b8d8d R11: 0000000000000003 R12: ffffffffffffffe8
R13: ffff8880a79fc000 R14: ffff88809aba0e00 R15: 0000000000000000
FS: 0000000001b51880(0000) GS:ffff8880ae800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000563f52cce140 CR3: 0000000093541000 CR4: 00000000001406f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
tcf_action_cleanup+0x62/0x1b0 net/sched/act_api.c:119
__tcf_action_put+0xfa/0x130 net/sched/act_api.c:135
__tcf_idr_release net/sched/act_api.c:165 [inline]
__tcf_idr_release+0x59/0xf0 net/sched/act_api.c:145
tcf_idr_release include/net/act_api.h:171 [inline]
tcf_ife_init+0x97c/0x1870 net/sched/act_ife.c:616
tcf_action_init_1+0x6b6/0xa40 net/sched/act_api.c:944
tcf_action_init+0x21a/0x330 net/sched/act_api.c:1000
tcf_action_add+0xf5/0x3b0 net/sched/act_api.c:1410
tc_ctl_action+0x390/0x488 net/sched/act_api.c:1465
rtnetlink_rcv_msg+0x45e/0xaf0 net/core/rtnetlink.c:5424
netlink_rcv_skb+0x177/0x450 net/netlink/af_netlink.c:2477
rtnetlink_rcv+0x1d/0x30 net/core/rtnetlink.c:5442
netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline]
netlink_unicast+0x58c/0x7d0 net/netlink/af_netlink.c:1328
netlink_sendmsg+0x91c/0xea0 net/netlink/af_netlink.c:1917
sock_sendmsg_nosec net/socket.c:639 [inline]
sock_sendmsg+0xd7/0x130 net/socket.c:659
____sys_sendmsg+0x753/0x880 net/socket.c:2330
___sys_sendmsg+0x100/0x170 net/socket.c:2384
__sys_sendmsg+0x105/0x1d0 net/socket.c:2417
__do_sys_sendmsg net/socket.c:2426 [inline]
__se_sys_sendmsg net/socket.c:2424 [inline]
__x64_sys_sendmsg+0x78/0xb0 net/socket.c:2424
do_syscall_64+0xfa/0x790 arch/x86/entry/common.c:294
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Fixes: 11a94d7fd80f ("net/sched: act_ife: validate the control action inside init()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit 91d2a812dfb9 ("locking/rwsem: Make handoff writer
optimistically spin on owner") will allow a recently woken up waiting
writer to spin on the owner. Unfortunately, if the owner happens to be
RWSEM_OWNER_UNKNOWN, the code will incorrectly spin on it leading to a
kernel crash. This is fixed by passing the proper non-spinnable bits
to rwsem_spin_on_owner() so that RWSEM_OWNER_UNKNOWN will be treated
as a non-spinnable target.
Fixes: 91d2a812dfb9 ("locking/rwsem: Make handoff writer optimistically spin on owner")
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20200115154336.8679-1-longman@redhat.com
|
Linus Torvalds
Pavel
Bartosz Golaszewski
Sakari Ailus
Jacek Anaszewski
Masami Hiramatsu
Jeff Layton
Eugene Syromiatnikov
Masami Ichikawa
Steven Rostedt (VMware)
Rahul Lakkireddy
Eric Dumazet
Olof Johansson
Ilie Halip
Michael Chan
Christian Brauner
Esben Haabendal
Michael Walle
Vignesh Raghavendra
Guenter Roeck
Luuk Paulussen
Gilles Buloz
Johan Hovold
Josef Bacik
Filipe Manana
Florian Fainelli
Vladimir Oltean
Michael Grzeschik
Kan Liang
Mark Rutland
Yonglong Liu
Cong Wang
Waiman Long