| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Commit 8d7ae22ae9f8 ("net: dsa: microchip: KSZ9477 register regmap
alignment to 32 bit boundaries") fixed an issue whereby regmap_reg_range
did not allow writes as 32 bit words to KSZ9477 PHY registers, this fix
for KSZ9896 is adapted from there as the same errata is present in
KSZ9896C as "Module 5: Certain PHY registers must be written as pairs
instead of singly" the explanation below is likewise taken from this
commit.
The commit provided code
to apply "Module 6: Certain PHY registers must be written as pairs instead
of singly" errata for KSZ9477 as this chip for certain PHY registers
(0xN120 to 0xN13F, N=1,2,3,4,5) must be accessed as 32 bit words instead
of 16 or 8 bit access.
Otherwise, adjacent registers (no matter if reserved or not) are
overwritten with 0x0.
Without this patch some registers (e.g. 0x113c or 0x1134) required for 32
bit access are out of valid regmap ranges.
As a result, following error is observed and KSZ9896 is not properly
configured:
ksz-switch spi1.0: can't rmw 32bit reg 0x113c: -EIO
ksz-switch spi1.0: can't rmw 32bit reg 0x1134: -EIO
ksz-switch spi1.0 lan1 (uninitialized): failed to connect to PHY: -EIO
ksz-switch spi1.0 lan1 (uninitialized): error -5 setting up PHY for tree 0, switch 0, port 0
The solution is to modify regmap_reg_range to allow accesses with 4 bytes
boundaries.
Fixes: 5c844d57aa78 ("net: dsa: microchip: fix writes to phy registers >= 0x10")
Signed-off-by: Jesse Van Gavere <jesse.vangavere@scioteq.com>
Link: https://patch.msgid.link/20241211092932.26881-1-jesse.vangavere@scioteq.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
MPIC.PIS must be set per phy interface type.
MPIC.LSC must be set per speed.
Do that strictly per datasheet, instead of hardcoding MPIC.PIS to GMII.
Fixes: 3590918b5d07 ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/20241211053012.368914-1-nikita.yoush@cogentembedded.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Similar to bonding driver, add NETIF_F_GSO_ENCAP_ALL to TEAM_VLAN_FEATURES
in order to support slave devices which propagate NETIF_F_GSO_UDP_TUNNEL &
NETIF_F_GSO_UDP_TUNNEL_CSUM as vlan_features.
Fixes: 3625920b62c3 ("teaming: fix vlan_features computing")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Cc: Ido Schimmel <idosch@idosch.org>
Cc: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20241210141245.327886-5-daniel@iogearbox.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Similarly as with bonding, fix the calculation of vlan_features to reuse
netdev_base_features() in order derive the set in the same way as
ndo_fix_features before iterating through the slave devices to refine the
feature set.
Fixes: 3625920b62c3 ("teaming: fix vlan_features computing")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Cc: Ido Schimmel <idosch@idosch.org>
Cc: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20241210141245.327886-4-daniel@iogearbox.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Drivers like mlx5 expose NIC's vlan_features such as
NETIF_F_GSO_UDP_TUNNEL & NETIF_F_GSO_UDP_TUNNEL_CSUM which are
later not propagated when the underlying devices are bonded and
a vlan device created on top of the bond.
Right now, the more cumbersome workaround for this is to create
the vlan on top of the mlx5 and then enslave the vlan devices
to a bond.
To fix this, add NETIF_F_GSO_ENCAP_ALL to BOND_VLAN_FEATURES
such that bond_compute_features() can probe and propagate the
vlan_features from the slave devices up to the vlan device.
Given the following bond:
# ethtool -i enp2s0f{0,1}np{0,1}
driver: mlx5_core
[...]
# ethtool -k enp2s0f0np0 | grep udp
tx-udp_tnl-segmentation: on
tx-udp_tnl-csum-segmentation: on
tx-udp-segmentation: on
rx-udp_tunnel-port-offload: on
rx-udp-gro-forwarding: off
# ethtool -k enp2s0f1np1 | grep udp
tx-udp_tnl-segmentation: on
tx-udp_tnl-csum-segmentation: on
tx-udp-segmentation: on
rx-udp_tunnel-port-offload: on
rx-udp-gro-forwarding: off
# ethtool -k bond0 | grep udp
tx-udp_tnl-segmentation: on
tx-udp_tnl-csum-segmentation: on
tx-udp-segmentation: on
rx-udp_tunnel-port-offload: off [fixed]
rx-udp-gro-forwarding: off
Before:
# ethtool -k bond0.100 | grep udp
tx-udp_tnl-segmentation: off [requested on]
tx-udp_tnl-csum-segmentation: off [requested on]
tx-udp-segmentation: on
rx-udp_tunnel-port-offload: off [fixed]
rx-udp-gro-forwarding: off
After:
# ethtool -k bond0.100 | grep udp
tx-udp_tnl-segmentation: on
tx-udp_tnl-csum-segmentation: on
tx-udp-segmentation: on
rx-udp_tunnel-port-offload: off [fixed]
rx-udp-gro-forwarding: off
Various users have run into this reporting performance issues when
configuring Cilium in vxlan tunneling mode and having the combination
of bond & vlan for the core devices connecting the Kubernetes cluster
to the outside world.
Fixes: a9b3ace44c7d ("bonding: fix vlan_features computing")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Cc: Ido Schimmel <idosch@idosch.org>
Cc: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20241210141245.327886-3-daniel@iogearbox.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
If a bonding device has slave devices, then the current logic to derive
the feature set for the master bond device is limited in that flags which
are fully supported by the underlying slave devices cannot be propagated
up to vlan devices which sit on top of bond devices. Instead, these get
blindly masked out via current NETIF_F_ALL_FOR_ALL logic.
vlan_features and mpls_features should reuse netdev_base_features() in
order derive the set in the same way as ndo_fix_features before iterating
through the slave devices to refine the feature set.
Fixes: a9b3ace44c7d ("bonding: fix vlan_features computing")
Fixes: 2e770b507ccd ("net: bonding: Inherit MPLS features from slave devices")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Cc: Ido Schimmel <idosch@idosch.org>
Cc: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20241210141245.327886-2-daniel@iogearbox.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Both bonding and team driver have logic to derive the base feature
flags before iterating over their slave devices to refine the set
via netdev_increment_features().
Add a small helper netdev_base_features() so this can be reused
instead of having it open-coded multiple times.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Cc: Ido Schimmel <idosch@idosch.org>
Cc: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20241210141245.327886-1-daniel@iogearbox.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In general, 'qlen' of any classful qdisc should keep track of the
number of packets that the qdisc itself and all of its children holds.
In case of netem, 'qlen' only accounts for the packets in its internal
tfifo. When netem is used with a child qdisc, the child qdisc can use
'qdisc_tree_reduce_backlog' to inform its parent, netem, about created
or dropped SKBs. This function updates 'qlen' and the backlog statistics
of netem, but netem does not account for changes made by a child qdisc.
'qlen' then indicates the wrong number of packets in the tfifo.
If a child qdisc creates new SKBs during enqueue and informs its parent
about this, netem's 'qlen' value is increased. When netem dequeues the
newly created SKBs from the child, the 'qlen' in netem is not updated.
If 'qlen' reaches the configured sch->limit, the enqueue function stops
working, even though the tfifo is not full.
Reproduce the bug:
Ensure that the sender machine has GSO enabled. Configure netem as root
qdisc and tbf as its child on the outgoing interface of the machine
as follows:
$ tc qdisc add dev <oif> root handle 1: netem delay 100ms limit 100
$ tc qdisc add dev <oif> parent 1:0 tbf rate 50Mbit burst 1542 latency 50ms
Send bulk TCP traffic out via this interface, e.g., by running an iPerf3
client on the machine. Check the qdisc statistics:
$ tc -s qdisc show dev <oif>
Statistics after 10s of iPerf3 TCP test before the fix (note that
netem's backlog > limit, netem stopped accepting packets):
qdisc netem 1: root refcnt 2 limit 1000 delay 100ms
Sent 2767766 bytes 1848 pkt (dropped 652, overlimits 0 requeues 0)
backlog 4294528236b 1155p requeues 0
qdisc tbf 10: parent 1:1 rate 50Mbit burst 1537b lat 50ms
Sent 2767766 bytes 1848 pkt (dropped 327, overlimits 7601 requeues 0)
backlog 0b 0p requeues 0
Statistics after the fix:
qdisc netem 1: root refcnt 2 limit 1000 delay 100ms
Sent 37766372 bytes 24974 pkt (dropped 9, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
qdisc tbf 10: parent 1:1 rate 50Mbit burst 1537b lat 50ms
Sent 37766372 bytes 24974 pkt (dropped 327, overlimits 96017 requeues 0)
backlog 0b 0p requeues 0
tbf segments the GSO SKBs (tbf_segment) and updates the netem's 'qlen'.
The interface fully stops transferring packets and "locks". In this case,
the child qdisc and tfifo are empty, but 'qlen' indicates the tfifo is at
its limit and no more packets are accepted.
This patch adds a counter for the entries in the tfifo. Netem's 'qlen' is
only decreased when a packet is returned by its dequeue function, and not
during enqueuing into the child qdisc. External updates to 'qlen' are thus
accounted for and only the behavior of the backlog statistics changes. As
in other qdiscs, 'qlen' then keeps track of how many packets are held in
netem and all of its children. As before, sch->limit remains as the
maximum number of packets in the tfifo. The same applies to netem's
backlog statistics.
Fixes: 50612537e9ab ("netem: fix classful handling")
Signed-off-by: Martin Ottens <martin.ottens@fau.de>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://patch.msgid.link/20241210131412.1837202-1-martin.ottens@fau.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
With this port schedule:
tc qdisc replace dev $send_if parent root handle 100 taprio \
num_tc 8 queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
map 0 1 2 3 4 5 6 7 \
base-time 0 cycle-time 10000 \
sched-entry S 01 1250 \
sched-entry S 02 1250 \
sched-entry S 04 1250 \
sched-entry S 08 1250 \
sched-entry S 10 1250 \
sched-entry S 20 1250 \
sched-entry S 40 1250 \
sched-entry S 80 1250 \
flags 2
ptp4l would fail to take TX timestamps of Pdelay_Resp messages like this:
increasing tx_timestamp_timeout may correct this issue, but it is likely caused by a driver bug
ptp4l[4134.168]: port 2: send peer delay response failed
It turns out that the driver can't take their TX timestamps because it
can't transmit them in the first place. And there's nothing special
about the Pdelay_Resp packets - they're just regular 68 byte packets.
But with this taprio configuration, the switch would refuse to send even
the ETH_ZLEN minimum packet size.
This should have definitely not been the case. When applying the taprio
config, the driver prints:
mscc_felix 0000:00:00.5: port 0 tc 0 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 1 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 2 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 3 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 4 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 5 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 6 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 7 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
and thus, everything under 132 bytes - ETH_FCS_LEN should have been sent
without problems. Yet it's not.
For the forwarding path, the configuration is fine, yet packets injected
from Linux get stuck with this schedule no matter what.
The first hint that the static guard bands are the cause of the problem
is that reverting Michael Walle's commit 297c4de6f780 ("net: dsa: felix:
re-enable TAS guard band mode") made things work. It must be that the
guard bands are calculated incorrectly.
I remembered that there is a magic constant in the driver, set to 33 ns
for no logical reason other than experimentation, which says "never let
the static guard bands get so large as to leave less than this amount of
remaining space in the time slot, because the queue system will refuse
to schedule packets otherwise, and they will get stuck". I had a hunch
that my previous experimentally-determined value was only good for
packets coming from the forwarding path, and that the CPU injection path
needed more.
I came to the new value of 35 ns through binary search, after seeing
that with 544 ns (the bit time required to send the Pdelay_Resp packet
at gigabit) it works. Again, this is purely experimental, there's no
logic and the manual doesn't say anything.
The new driver prints for this schedule look like this:
mscc_felix 0000:00:00.5: port 0 tc 0 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 1 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 2 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 3 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 4 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 5 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 6 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 7 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
So yes, the maximum MTU is now even smaller by 1 byte than before.
This is maybe counter-intuitive, but makes more sense with a diagram of
one time slot.
Before:
Gate open Gate close
| |
v 1250 ns total time slot duration v
<---------------------------------------------------->
<----><---------------------------------------------->
33 ns 1217 ns static guard band
useful
Gate open Gate close
| |
v 1250 ns total time slot duration v
<---------------------------------------------------->
<-----><--------------------------------------------->
35 ns 1215 ns static guard band
useful
The static guard band implemented by this switch hardware directly
determines the maximum allowable MTU for that traffic class. The larger
it is, the earlier the switch will stop scheduling frames for
transmission, because otherwise they might overrun the gate close time
(and avoiding that is the entire purpose of Michael's patch).
So, we now have guard bands smaller by 2 ns, thus, in this particular
case, we lose a byte of the maximum MTU.
Fixes: 11afdc6526de ("net: dsa: felix: tc-taprio intervals smaller than MTU should send at least one packet")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Link: https://patch.msgid.link/20241210132640.3426788-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When `skb_splice_from_iter` was introduced, it inadvertently added
checksumming for AF_UNIX sockets. This resulted in significant
slowdowns, for example when using sendfile over unix sockets.
Using the test code in [1] in my test setup (2G single core qemu),
the client receives a 1000M file in:
- without the patch: 1482ms (+/- 36ms)
- with the patch: 652.5ms (+/- 22.9ms)
This commit addresses the issue by marking checksumming as unnecessary in
`unix_stream_sendmsg`
Cc: stable@vger.kernel.org
Signed-off-by: Frederik Deweerdt <deweerdt.lkml@gmail.com>
Fixes: 2e910b95329c ("net: Add a function to splice pages into an skbuff for MSG_SPLICE_PAGES")
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Link: https://patch.msgid.link/Z1fMaHkRf8cfubuE@xiberoa
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add the following Telit FE910C04 compositions:
0x10c0: rmnet + tty (AT/NMEA) + tty (AT) + tty (diag)
T: Bus=02 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#= 13 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10c0 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FE910
S: SerialNumber=f71b8b32
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x10c4: rmnet + tty (AT) + tty (AT) + tty (diag)
T: Bus=02 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#= 14 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10c4 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FE910
S: SerialNumber=f71b8b32
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x10c8: rmnet + tty (AT) + tty (diag) + DPL (data packet logging) + adb
T: Bus=02 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#= 17 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10c8 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FE910
S: SerialNumber=f71b8b32
C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none)
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Link: https://patch.msgid.link/20241209151821.3688829-1-dnlplm@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
gc->irq_contexts is not freeded if one of the later operations
fail.
Suggested-by: Michael Kelley <mhklinux@outlook.com>
Fixes: 8afefc361209 ("net: mana: Assigning IRQ affinity on HT cores")
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Saurabh Sengar <ssengar@linux.microsoft.com>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Link: https://patch.msgid.link/20241209175751.287738-3-mlevitsk@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 8afefc361209 ("net: mana: Assigning IRQ affinity on HT cores")
added memory allocation in mana_gd_setup_irqs of 'irqs' but the code
doesn't free this temporary array in the success path.
This was caught by kmemleak.
Fixes: 8afefc361209 ("net: mana: Assigning IRQ affinity on HT cores")
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Saurabh Sengar <ssengar@linux.microsoft.com>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Link: https://patch.msgid.link/20241209175751.287738-2-mlevitsk@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This is part of an effort to assign a section in MAINTAINERS to header
files related to Networking. In this case the files named ethool.h.
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241210-mnt-ethtool-h-v1-1-2a40b567939d@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
nf_tables_chain_destroy can sleep, it can't be used from call_rcu
callbacks.
Moreover, nf_tables_rule_release() is only safe for error unwinding,
while transaction mutex is held and the to-be-desroyed rule was not
exposed to either dataplane or dumps, as it deactives+frees without
the required synchronize_rcu() in-between.
nft_rule_expr_deactivate() callbacks will change ->use counters
of other chains/sets, see e.g. nft_lookup .deactivate callback, these
must be serialized via transaction mutex.
Also add a few lockdep asserts to make this more explicit.
Calling synchronize_rcu() isn't ideal, but fixing this without is hard
and way more intrusive. As-is, we can get:
WARNING: .. net/netfilter/nf_tables_api.c:5515 nft_set_destroy+0x..
Workqueue: events nf_tables_trans_destroy_work
RIP: 0010:nft_set_destroy+0x3fe/0x5c0
Call Trace:
<TASK>
nf_tables_trans_destroy_work+0x6b7/0xad0
process_one_work+0x64a/0xce0
worker_thread+0x613/0x10d0
In case the synchronize_rcu becomes an issue, we can explore alternatives.
One way would be to allocate nft_trans_rule objects + one nft_trans_chain
object, deactivate the rules + the chain and then defer the freeing to the
nft destroy workqueue. We'd still need to keep the synchronize_rcu path as
a fallback to handle -ENOMEM corner cases though.
Reported-by: syzbot+b26935466701e56cfdc2@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/67478d92.050a0220.253251.0062.GAE@google.com/T/
Fixes: c03d278fdf35 ("netfilter: nf_tables: wait for rcu grace period on net_device removal")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Deletion of the last rule referencing a given idletimer may happen at
the same time as a read of its file in sysfs:
| ======================================================
| WARNING: possible circular locking dependency detected
| 6.12.0-rc7-01692-g5e9a28f41134-dirty #594 Not tainted
| ------------------------------------------------------
| iptables/3303 is trying to acquire lock:
| ffff8881057e04b8 (kn->active#48){++++}-{0:0}, at: __kernfs_remove+0x20
|
| but task is already holding lock:
| ffffffffa0249068 (list_mutex){+.+.}-{3:3}, at: idletimer_tg_destroy_v]
|
| which lock already depends on the new lock.
A simple reproducer is:
| #!/bin/bash
|
| while true; do
| iptables -A INPUT -i foo -j IDLETIMER --timeout 10 --label "testme"
| iptables -D INPUT -i foo -j IDLETIMER --timeout 10 --label "testme"
| done &
| while true; do
| cat /sys/class/xt_idletimer/timers/testme >/dev/null
| done
Avoid this by freeing list_mutex right after deleting the element from
the list, then continuing with the teardown.
Fixes: 0902b469bd25 ("netfilter: xtables: idletimer target implementation")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
On some systems, neighbor discoveries from ns1 for fec0:42::1 (i.e., the
martian trap address) would happen at the wrong time and cause
false-negative test result.
Problem analysis also discovered that IPv6 martian ping test was broken
in that sent neighbor discoveries, not echo requests were inadvertently
trapped
Avoid the race condition by introducing the neighbors to each other
upfront. Also pin down the firewall rules to matching on echo requests
only.
Fixes: efb056e5f1f0 ("netfilter: ip6t_rpfilter: Fix regression with VRF interfaces")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Currently the stop routine of rswitch driver does not immediately
prevent hardware from continuing to update descriptors and requesting
interrupts.
It can happen that when rswitch_stop() executes the masking of
interrupts from the queues of the port being closed, napi poll for
that port is already scheduled or running on a different CPU. When
execution of this napi poll completes, it will unmask the interrupts.
And unmasked interrupt can fire after rswitch_stop() returns from
napi_disable() call. Then, the handler won't mask it, because
napi_schedule_prep() will return false, and interrupt storm will
happen.
This can't be fixed by making rswitch_stop() call napi_disable() before
masking interrupts. In this case, the interrupt storm will happen if
interrupt fires between napi_disable() and masking.
Fix this by checking for priv->opened_ports bit when unmasking
interrupts after napi poll. For that to be consistent, move
priv->opened_ports changes into spinlock-protected areas, and reorder
other operations in rswitch_open() and rswitch_stop() accordingly.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Fixes: 3590918b5d07 ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Link: https://patch.msgid.link/20241209113204.175015-1-nikita.yoush@cogentembedded.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The device tree node saved in the rswitch_device structure is used at
several driver locations. So passing this node to of_node_put() after
the first use is wrong.
Move of_node_put() for this node to exit paths.
Fixes: b46f1e579329 ("net: renesas: rswitch: Simplify struct phy * handling")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://patch.msgid.link/20241208095004.69468-5-nikita.yoush@cogentembedded.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If error path is taken while filling descriptor for a frame, skb
pointer is left in the entry. Later, on the ring entry reuse, the
same entry could be used as a part of a multi-descriptor frame,
and skb for that new frame could be stored in a different entry.
Then, the stale pointer will reach the completion routine, and passed
to the release operation.
Fix that by clearing the saved skb pointer at the error path.
Fixes: d2c96b9d5f83 ("net: rswitch: Add jumbo frames handling for TX")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://patch.msgid.link/20241208095004.69468-4-nikita.yoush@cogentembedded.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If hardware is already transmitting, it can start handling the
descriptor being written to immediately after it observes updated DT
field, before the queue is kicked by a write to GWTRC.
If the start_xmit() execution is preempted at unfortunate moment, this
transmission can complete, and interrupt handled, before gq->cur gets
updated. With the current implementation of completion, this will cause
the last entry not completed.
Fix that by changing completion loop to check DT values directly, instead
of depending on gq->cur.
Fixes: 3590918b5d07 ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://patch.msgid.link/20241208095004.69468-3-nikita.yoush@cogentembedded.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When sending frame split into multiple descriptors, hardware processes
descriptors one by one, including writing back DT values. The first
descriptor could be already marked as completed when processing of
next descriptors for the same frame is still in progress.
Although only the last descriptor is configured to generate interrupt,
completion of the first descriptor could be noticed by the driver when
handling interrupt for the previous frame.
Currently, driver stores skb in the entry that corresponds to the first
descriptor. This results into skb could be unmapped and freed when
hardware did not complete the send yet. This opens a window for
corrupting the data being sent.
Fix this by saving skb in the entry that corresponds to the last
descriptor used to send the frame.
Fixes: d2c96b9d5f83 ("net: rswitch: Add jumbo frames handling for TX")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://patch.msgid.link/20241208095004.69468-2-nikita.yoush@cogentembedded.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Ensure there is enough space before adding MPTCP options in
tcp_syn_options().
Without this check, 'remaining' could underflow, and causes issues. If
there is not enough space, MPTCP should not be used.
Signed-off-by: MoYuanhao <moyuanhao3676@163.com>
Fixes: cec37a6e41aa ("mptcp: Handle MP_CAPABLE options for outgoing connections")
Cc: stable@vger.kernel.org
Acked-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
[ Matt: Add Fixes, cc Stable, update Description ]
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20241209-net-mptcp-check-space-syn-v1-1-2da992bb6f74@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
net.ipv4.nexthop_compat_mode was added when nexthop objects were added to
provide the view of nexthop objects through the usual lens of the route
UAPI. As nexthop objects evolved, the information provided through this
lens became incomplete. For example, details of resilient nexthop groups
are obviously omitted.
Now that 16-bit nexthop group weights are a thing, the 8-bit UAPI cannot
convey the >8-bit weight accurately. Instead of inventing workarounds for
an obsolete interface, just document the expectations of inaccuracy.
Fixes: b72a6a7ab957 ("net: nexthop: Increase weight to u16")
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/b575e32399ccacd09079b2a218255164535123bd.1733740749.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The 5760X (P7) chip's HW GRO/LRO interface is very similar to that of
the previous generation (5750X or P5). However, the aggregation ID
fields in the completion structures on P7 have been redefined from
16 bits to 12 bits. The freed up 4 bits are redefined for part of the
metadata such as the VLAN ID. The aggregation ID mask was not modified
when adding support for P7 chips. Including the extra 4 bits for the
aggregation ID can potentially cause the driver to store or fetch the
packet header of GRO/LRO packets in the wrong TPA buffer. It may hit
the BUG() condition in __skb_pull() because the SKB contains no valid
packet header:
kernel BUG at include/linux/skbuff.h:2766!
Oops: invalid opcode: 0000 1 PREEMPT SMP NOPTI
CPU: 4 UID: 0 PID: 0 Comm: swapper/4 Kdump: loaded Tainted: G OE 6.12.0-rc2+ #7
Tainted: [O]=OOT_MODULE, [E]=UNSIGNED_MODULE
Hardware name: Dell Inc. PowerEdge R760/0VRV9X, BIOS 1.0.1 12/27/2022
RIP: 0010:eth_type_trans+0xda/0x140
Code: 80 00 00 00 eb c1 8b 47 70 2b 47 74 48 8b 97 d0 00 00 00 83 f8 01 7e 1b 48 85 d2 74 06 66 83 3a ff 74 09 b8 00 04 00 00 eb a5 <0f> 0b b8 00 01 00 00 eb 9c 48 85 ff 74 eb 31 f6 b9 02 00 00 00 48
RSP: 0018:ff615003803fcc28 EFLAGS: 00010283
RAX: 00000000000022d2 RBX: 0000000000000003 RCX: ff2e8c25da334040
RDX: 0000000000000040 RSI: ff2e8c25c1ce8000 RDI: ff2e8c25869f9000
RBP: ff2e8c258c31c000 R08: ff2e8c25da334000 R09: 0000000000000001
R10: ff2e8c25da3342c0 R11: ff2e8c25c1ce89c0 R12: ff2e8c258e0990b0
R13: ff2e8c25bb120000 R14: ff2e8c25c1ce89c0 R15: ff2e8c25869f9000
FS: 0000000000000000(0000) GS:ff2e8c34be300000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055f05317e4c8 CR3: 000000108bac6006 CR4: 0000000000773ef0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe07f0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
<IRQ>
? die+0x33/0x90
? do_trap+0xd9/0x100
? eth_type_trans+0xda/0x140
? do_error_trap+0x65/0x80
? eth_type_trans+0xda/0x140
? exc_invalid_op+0x4e/0x70
? eth_type_trans+0xda/0x140
? asm_exc_invalid_op+0x16/0x20
? eth_type_trans+0xda/0x140
bnxt_tpa_end+0x10b/0x6b0 [bnxt_en]
? bnxt_tpa_start+0x195/0x320 [bnxt_en]
bnxt_rx_pkt+0x902/0xd90 [bnxt_en]
? __bnxt_tx_int.constprop.0+0x89/0x300 [bnxt_en]
? kmem_cache_free+0x343/0x440
? __bnxt_tx_int.constprop.0+0x24f/0x300 [bnxt_en]
__bnxt_poll_work+0x193/0x370 [bnxt_en]
bnxt_poll_p5+0x9a/0x300 [bnxt_en]
? try_to_wake_up+0x209/0x670
__napi_poll+0x29/0x1b0
Fix it by redefining the aggregation ID mask for P5_PLUS chips to be
12 bits. This will work because the maximum aggregation ID is less
than 4096 on all P5_PLUS chips.
Fixes: 13d2d3d381ee ("bnxt_en: Add new P7 hardware interface definitions")
Reviewed-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241209015448.1937766-1-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After the blamed commit below, udp_rehash() is supposed to be called
with both local and remote addresses set.
Currently that is already the case for IPv6 sockets, but for IPv4 the
destination address is updated after rehashing.
Address the issue moving the destination address and port initialization
before rehashing.
Fixes: 1b29a730ef8b ("ipv6/udp: Add 4-tuple hash for connected socket")
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/4761e466ab9f7542c68cdc95f248987d127044d2.1733499715.git.pabeni@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
virtnet_sq_bind_xsk_pool() flushes tx skbs and then resets tx queue, so
DQL counters need to be reset when flushing has actually occurred, Add
virtnet_sq_free_unused_buf_done() as a callback for virtqueue_resize()
to handle this.
Fixes: 21a4e3ce6dc7 ("virtio_net: xsk: bind/unbind xsk for tx")
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When virtqueue_reset() has actually recycled all unused buffers,
additional work may be required in some cases. Relying solely on its
return status is fragile, so introduce a new function argument
'recycle_done', which is invoked when it really occurs.
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
virtnet_tx_resize() flushes remaining tx skbs, requiring DQL counters to
be reset when flushing has actually occurred. Add
virtnet_sq_free_unused_buf_done() as a callback for virtqueue_reset() to
handle this.
Fixes: c8bd1f7f3e61 ("virtio_net: add support for Byte Queue Limits")
Cc: <stable@vger.kernel.org> # v6.11+
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When virtqueue_resize() has actually recycled all unused buffers,
additional work may be required in some cases. Relying solely on its
return status is fragile, so introduce a new function argument
'recycle_done', which is invoked when the recycle really occurs.
Cc: <stable@vger.kernel.org> # v6.11+
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
While not harmful, using vq2rxq where it's always sq appears odd.
Replace it with the more appropriate vq2txq for clarity and correctness.
Fixes: 89f86675cb03 ("virtio_net: xsk: tx: support xmit xsk buffer")
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When virtnet_close is followed by virtnet_open, some TX completions can
possibly remain unconsumed, until they are finally processed during the
first NAPI poll after the netdev_tx_reset_queue(), resulting in a crash
[1]. Commit b96ed2c97c79 ("virtio_net: move netdev_tx_reset_queue() call
before RX napi enable") was not sufficient to eliminate all BQL crash
cases for virtio-net.
This issue can be reproduced with the latest net-next master by running:
`while :; do ip l set DEV down; ip l set DEV up; done` under heavy network
TX load from inside the machine.
netdev_tx_reset_queue() can actually be dropped from virtnet_open path;
the device is not stopped in any case. For BQL core part, it's just like
traffic nearly ceases to exist for some period. For stall detector added
to BQL, even if virtnet_close could somehow lead to some TX completions
delayed for long, followed by virtnet_open, we can just take it as stall
as mentioned in commit 6025b9135f7a ("net: dqs: add NIC stall detector
based on BQL"). Note also that users can still reset stall_max via sysfs.
So, drop netdev_tx_reset_queue() from virtnet_enable_queue_pair(). This
eliminates the BQL crashes. As a result, netdev_tx_reset_queue() is now
explicitly required in freeze/restore path. This patch adds it to
immediately after free_unused_bufs(), following the rule of thumb:
netdev_tx_reset_queue() should follow any SKB freeing not followed by
netdev_tx_completed_queue(). This seems the most consistent and
streamlined approach, and now netdev_tx_reset_queue() runs whenever
free_unused_bufs() is done.
[1]:
------------[ cut here ]------------
kernel BUG at lib/dynamic_queue_limits.c:99!
Oops: invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
CPU: 7 UID: 0 PID: 1598 Comm: ip Tainted: G N 6.12.0net-next_main+ #2
Tainted: [N]=TEST
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), \
BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014
RIP: 0010:dql_completed+0x26b/0x290
Code: b7 c2 49 89 e9 44 89 da 89 c6 4c 89 d7 e8 ed 17 47 00 58 65 ff 0d
4d 27 90 7e 0f 85 fd fe ff ff e8 ea 53 8d ff e9 f3 fe ff ff <0f> 0b 01
d2 44 89 d1 29 d1 ba 00 00 00 00 0f 48 ca e9 28 ff ff ff
RSP: 0018:ffffc900002b0d08 EFLAGS: 00010297
RAX: 0000000000000000 RBX: ffff888102398c80 RCX: 0000000080190009
RDX: 0000000000000000 RSI: 000000000000006a RDI: 0000000000000000
RBP: ffff888102398c00 R08: 0000000000000000 R09: 0000000000000000
R10: 00000000000000ca R11: 0000000000015681 R12: 0000000000000001
R13: ffffc900002b0d68 R14: ffff88811115e000 R15: ffff8881107aca40
FS: 00007f41ded69500(0000) GS:ffff888667dc0000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000556ccc2dc1a0 CR3: 0000000104fd8003 CR4: 0000000000772ef0
PKRU: 55555554
Call Trace:
<IRQ>
? die+0x32/0x80
? do_trap+0xd9/0x100
? dql_completed+0x26b/0x290
? dql_completed+0x26b/0x290
? do_error_trap+0x6d/0xb0
? dql_completed+0x26b/0x290
? exc_invalid_op+0x4c/0x60
? dql_completed+0x26b/0x290
? asm_exc_invalid_op+0x16/0x20
? dql_completed+0x26b/0x290
__free_old_xmit+0xff/0x170 [virtio_net]
free_old_xmit+0x54/0xc0 [virtio_net]
virtnet_poll+0xf4/0xe30 [virtio_net]
? __update_load_avg_cfs_rq+0x264/0x2d0
? update_curr+0x35/0x260
? reweight_entity+0x1be/0x260
__napi_poll.constprop.0+0x28/0x1c0
net_rx_action+0x329/0x420
? enqueue_hrtimer+0x35/0x90
? trace_hardirqs_on+0x1d/0x80
? kvm_sched_clock_read+0xd/0x20
? sched_clock+0xc/0x30
? kvm_sched_clock_read+0xd/0x20
? sched_clock+0xc/0x30
? sched_clock_cpu+0xd/0x1a0
handle_softirqs+0x138/0x3e0
do_softirq.part.0+0x89/0xc0
</IRQ>
<TASK>
__local_bh_enable_ip+0xa7/0xb0
virtnet_open+0xc8/0x310 [virtio_net]
__dev_open+0xfa/0x1b0
__dev_change_flags+0x1de/0x250
dev_change_flags+0x22/0x60
do_setlink.isra.0+0x2df/0x10b0
? rtnetlink_rcv_msg+0x34f/0x3f0
? netlink_rcv_skb+0x54/0x100
? netlink_unicast+0x23e/0x390
? netlink_sendmsg+0x21e/0x490
? ____sys_sendmsg+0x31b/0x350
? avc_has_perm_noaudit+0x67/0xf0
? cred_has_capability.isra.0+0x75/0x110
? __nla_validate_parse+0x5f/0xee0
? __pfx___probestub_irq_enable+0x3/0x10
? __create_object+0x5e/0x90
? security_capable+0x3b/0x70
rtnl_newlink+0x784/0xaf0
? avc_has_perm_noaudit+0x67/0xf0
? cred_has_capability.isra.0+0x75/0x110
? stack_depot_save_flags+0x24/0x6d0
? __pfx_rtnl_newlink+0x10/0x10
rtnetlink_rcv_msg+0x34f/0x3f0
? do_syscall_64+0x6c/0x180
? entry_SYSCALL_64_after_hwframe+0x76/0x7e
? __pfx_rtnetlink_rcv_msg+0x10/0x10
netlink_rcv_skb+0x54/0x100
netlink_unicast+0x23e/0x390
netlink_sendmsg+0x21e/0x490
____sys_sendmsg+0x31b/0x350
? copy_msghdr_from_user+0x6d/0xa0
___sys_sendmsg+0x86/0xd0
? __pte_offset_map+0x17/0x160
? preempt_count_add+0x69/0xa0
? __call_rcu_common.constprop.0+0x147/0x610
? preempt_count_add+0x69/0xa0
? preempt_count_add+0x69/0xa0
? _raw_spin_trylock+0x13/0x60
? trace_hardirqs_on+0x1d/0x80
__sys_sendmsg+0x66/0xc0
do_syscall_64+0x6c/0x180
entry_SYSCALL_64_after_hwframe+0x76/0x7e
RIP: 0033:0x7f41defe5b34
Code: 15 e1 12 0f 00 f7 d8 64 89 02 b8 ff ff ff ff eb bf 0f 1f 44 00 00
f3 0f 1e fa 80 3d 35 95 0f 00 00 74 13 b8 2e 00 00 00 0f 05 <48> 3d 00
f0 ff ff 77 4c c3 0f 1f 00 55 48 89 e5 48 83 ec 20 89 55
RSP: 002b:00007ffe5336ecc8 EFLAGS: 00000202 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 00007f41defe5b34
RDX: 0000000000000000 RSI: 00007ffe5336ed30 RDI: 0000000000000003
RBP: 00007ffe5336eda0 R08: 0000000000000010 R09: 0000000000000001
R10: 00007ffe5336f6f9 R11: 0000000000000202 R12: 0000000000000003
R13: 0000000067452259 R14: 0000556ccc28b040 R15: 0000000000000000
</TASK>
[...]
Fixes: c8bd1f7f3e61 ("virtio_net: add support for Byte Queue Limits")
Cc: <stable@vger.kernel.org> # v6.11+
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
[ pabeni: trimmed possibly troublesome separator ]
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Due to target variable is being reassigned in npc_install_flow()
function, PF multicast rules are not getting installed.
This patch addresses the issue by fixing the "IF" condition
checks when rules are installed by AF.
Fixes: 6c40ca957fe5 ("octeontx2-pf: Adds TC offload support").
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241205113435.10601-1-gakula@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The module parameter qcaspi_pluggable controls if QCA7000 signature
should be checked at driver probe (current default) or not. Unfortunately
this could fail in case the chip is temporary in reset, which isn't under
total control by the Linux host. So disable this check per default
in order to avoid unexpected probe failures.
Fixes: 291ab06ecf67 ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://patch.msgid.link/20241206184643.123399-3-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Storing the maximum clock speed in module parameter qcaspi_clkspeed
has the unintended side effect that the first probed instance
defines the value for all other instances. Fix this issue by storing
it in max_speed_hz of the relevant SPI device.
This fix keeps the priority of the speed parameter (module parameter,
device tree property, driver default). Btw this uses the opportunity
to get the rid of the unused member clkspeed.
Fixes: 291ab06ecf67 ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://patch.msgid.link/20241206184643.123399-2-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
t4_set_vf_mac_acl() uses pf to set mac addr, but t4vf_get_vf_mac_acl()
uses port number to get mac addr, this leads to error when an attempt
to set MAC address on VF's of PF2 and PF3.
This patch fixes the issue by using port number to set mac address.
Fixes: e0cdac65ba26 ("cxgb4vf: configure ports accessible by the VF")
Signed-off-by: Anumula Murali Mohan Reddy <anumula@chelsio.com>
Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241206062014.49414-1-anumula@chelsio.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On port initialization, we configure the maximum frame length accepted
by the receive module associated with the port. This value is currently
written to the MAX_LEN field of the DEV10G_MAC_ENA_CFG register, when in
fact, it should be written to the DEV10G_MAC_MAXLEN_CFG register. Fix
this.
Fixes: 946e7fd5053a ("net: sparx5: add port module support")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When doing port mirroring, the physical port to send the frame to, is
written to the FRMC_PORT_VAL field of the QFWD_FRAME_COPY_CFG register.
This field is 7 bits wide on sparx5 and 6 bits wide on lan969x, and has
a default value of 65 and 30, respectively (the number of front ports).
On mirror deletion, we set the default value of the monitor port to
65 for this field, in case no more ports exists for the mirror. Needless
to say, this will not fit the 6 bits on lan969x.
Fix this by correctly using the n_ports constant instead.
Fixes: 3f9e46347a46 ("net: sparx5: use SPX5_CONST for constants which already have a symbol")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The FDMA handler is responsible for scheduling a NAPI poll, which will
eventually fetch RX packets from the FDMA queue. Currently, the FDMA
handler is run in a threaded context. For some reason, this kills
performance. Admittedly, I did not do a thorough investigation to see
exactly what causes the issue, however, I noticed that in the other
driver utilizing the same FDMA engine, we run the FDMA handler in hard
IRQ context.
Fix this performance issue, by running the FDMA handler in hard IRQ
context, not deferring any work to a thread.
Prior to this change, the RX UDP performance was:
Interval Transfer Bitrate Jitter
0.00-10.20 sec 44.6 MBytes 36.7 Mbits/sec 0.027 ms
After this change, the rx UDP performance is:
Interval Transfer Bitrate Jitter
0.00-9.12 sec 1.01 GBytes 953 Mbits/sec 0.020 ms
Fixes: 10615907e9b5 ("net: sparx5: switchdev: adding frame DMA functionality")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are mixing the use of spin_lock() and spin_lock_irqsave() functions
in the PTP handler of lan969x. Fix this by correctly using the _irqsave
variants.
Fixes: 24fe83541755 ("net: lan969x: add PTP handler function")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
[1]: https://lore.kernel.org/netdev/20241024-sparx5-lan969x-switch-driver-2-v2-10-a0b5fae88a0f@microchip.com/
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Depmod reports a cyclic dependency between modules sparx5-switch.ko and
lan969x-switch.ko:
depmod: ERROR: Cycle detected: lan969x_switch -> sparx5_switch -> lan969x_switch
depmod: ERROR: Found 2 modules in dependency cycles!
make[2]: *** [scripts/Makefile.modinst:132: depmod] Error 1
make: *** [Makefile:224: __sub-make] Error 2
This makes sense, as they both require symbols from each other.
Fix this by compiling lan969x support into the sparx5-switch.ko module.
In order to do this, in a sensible way, we move the lan969x/ dir into
the sparx5/ dir and do some code cleanup of code that is no longer
required.
After this patch, depmod will no longer complain, as lan969x support is
compiled into the sparx5-swicth.ko module, and can no longer be compiled
as a standalone module.
Fixes: 98a01119608d ("net: sparx5: add compatible string for lan969x")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If rtnl_get_peer_net() fails, then propagate the error code. Don't
return success.
Fixes: 48327566769a ("rtnetlink: fix double call of rtnl_link_get_net_ifla()")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/a2d20cd4-387a-4475-887c-bb7d0e88e25a@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
An unsupported RX filter will leave the port with TX timestamping still
applied as per the new request, rather than the old setting. When
parsing the tx_type, don't apply it just yet, but delay that until after
we've parsed the rx_filter as well (and potentially returned -ERANGE for
that).
Similarly, copy_to_user() may fail, which is a rare occurrence, but
should still be treated by unwinding what was done.
Fixes: 96ca08c05838 ("net: mscc: ocelot: set up traps for PTP packets")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241205145519.1236778-6-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The Felix DSA driver presents unique challenges that make the simplistic
ocelot PTP TX timestamping procedure unreliable: any transmitted packet
may be lost in hardware before it ever leaves our local system.
This may happen because there is congestion on the DSA conduit, the
switch CPU port or even user port (Qdiscs like taprio may delay packets
indefinitely by design).
The technical problem is that the kernel, i.e. ocelot_port_add_txtstamp_skb(),
runs out of timestamp IDs eventually, because it never detects that
packets are lost, and keeps the IDs of the lost packets on hold
indefinitely. The manifestation of the issue once the entire timestamp
ID range becomes busy looks like this in dmesg:
mscc_felix 0000:00:00.5: port 0 delivering skb without TX timestamp
mscc_felix 0000:00:00.5: port 1 delivering skb without TX timestamp
At the surface level, we need a timeout timer so that the kernel knows a
timestamp ID is available again. But there is a deeper problem with the
implementation, which is the monotonically increasing ocelot_port->ts_id.
In the presence of packet loss, it will be impossible to detect that and
reuse one of the holes created in the range of free timestamp IDs.
What we actually need is a bitmap of 63 timestamp IDs tracking which one
is available. That is able to use up holes caused by packet loss, but
also gives us a unique opportunity to not implement an actual timer_list
for the timeout timer (very complicated in terms of locking).
We could only declare a timestamp ID stale on demand (lazily), aka when
there's no other timestamp ID available. There are pros and cons to this
approach: the implementation is much more simple than per-packet timers
would be, but most of the stale packets would be quasi-leaked - not
really leaked, but blocked in driver memory, since this algorithm sees
no reason to free them.
An improved technique would be to check for stale timestamp IDs every
time we allocate a new one. Assuming a constant flux of PTP packets,
this avoids stale packets being blocked in memory, but of course,
packets lost at the end of the flux are still blocked until the flux
resumes (nobody left to kick them out).
Since implementing per-packet timers is way too complicated, this should
be good enough.
Testing procedure:
Persistently block traffic class 5 and try to run PTP on it:
$ tc qdisc replace dev swp3 parent root taprio num_tc 8 \
map 0 1 2 3 4 5 6 7 queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
base-time 0 sched-entry S 0xdf 100000 flags 0x2
[ 126.948141] mscc_felix 0000:00:00.5: port 3 tc 5 min gate length 0 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 1 octets including FCS
$ ptp4l -i swp3 -2 -P -m --socket_priority 5 --fault_reset_interval ASAP --logSyncInterval -3
ptp4l[70.351]: port 1 (swp3): INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[70.354]: port 0 (/var/run/ptp4l): INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[70.358]: port 0 (/var/run/ptp4lro): INITIALIZING to LISTENING on INIT_COMPLETE
[ 70.394583] mscc_felix 0000:00:00.5: port 3 timestamp id 0
ptp4l[70.406]: timed out while polling for tx timestamp
ptp4l[70.406]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[70.406]: port 1 (swp3): send peer delay response failed
ptp4l[70.407]: port 1 (swp3): clearing fault immediately
ptp4l[70.952]: port 1 (swp3): new foreign master d858d7.fffe.00ca6d-1
[ 71.394858] mscc_felix 0000:00:00.5: port 3 timestamp id 1
ptp4l[71.400]: timed out while polling for tx timestamp
ptp4l[71.400]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[71.401]: port 1 (swp3): send peer delay response failed
ptp4l[71.401]: port 1 (swp3): clearing fault immediately
[ 72.393616] mscc_felix 0000:00:00.5: port 3 timestamp id 2
ptp4l[72.401]: timed out while polling for tx timestamp
ptp4l[72.402]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[72.402]: port 1 (swp3): send peer delay response failed
ptp4l[72.402]: port 1 (swp3): clearing fault immediately
ptp4l[72.952]: port 1 (swp3): new foreign master d858d7.fffe.00ca6d-1
[ 73.395291] mscc_felix 0000:00:00.5: port 3 timestamp id 3
ptp4l[73.400]: timed out while polling for tx timestamp
ptp4l[73.400]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[73.400]: port 1 (swp3): send peer delay response failed
ptp4l[73.400]: port 1 (swp3): clearing fault immediately
[ 74.394282] mscc_felix 0000:00:00.5: port 3 timestamp id 4
ptp4l[74.400]: timed out while polling for tx timestamp
ptp4l[74.401]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[74.401]: port 1 (swp3): send peer delay response failed
ptp4l[74.401]: port 1 (swp3): clearing fault immediately
ptp4l[74.953]: port 1 (swp3): new foreign master d858d7.fffe.00ca6d-1
[ 75.396830] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 0 which seems lost
[ 75.405760] mscc_felix 0000:00:00.5: port 3 timestamp id 0
ptp4l[75.410]: timed out while polling for tx timestamp
ptp4l[75.411]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[75.411]: port 1 (swp3): send peer delay response failed
ptp4l[75.411]: port 1 (swp3): clearing fault immediately
(...)
Remove the blocking condition and see that the port recovers:
$ same tc command as above, but use "sched-entry S 0xff" instead
$ same ptp4l command as above
ptp4l[99.489]: port 1 (swp3): INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[99.490]: port 0 (/var/run/ptp4l): INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[99.492]: port 0 (/var/run/ptp4lro): INITIALIZING to LISTENING on INIT_COMPLETE
[ 100.403768] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 0 which seems lost
[ 100.412545] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 1 which seems lost
[ 100.421283] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 2 which seems lost
[ 100.430015] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 3 which seems lost
[ 100.438744] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 4 which seems lost
[ 100.447470] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 100.505919] mscc_felix 0000:00:00.5: port 3 timestamp id 0
ptp4l[100.963]: port 1 (swp3): new foreign master d858d7.fffe.00ca6d-1
[ 101.405077] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 101.507953] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 102.405405] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 102.509391] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 103.406003] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 103.510011] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 104.405601] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 104.510624] mscc_felix 0000:00:00.5: port 3 timestamp id 0
ptp4l[104.965]: selected best master clock d858d7.fffe.00ca6d
ptp4l[104.966]: port 1 (swp3): assuming the grand master role
ptp4l[104.967]: port 1 (swp3): LISTENING to GRAND_MASTER on RS_GRAND_MASTER
[ 105.106201] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.232420] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.359001] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.405500] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.485356] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.511220] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.610938] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.737237] mscc_felix 0000:00:00.5: port 3 timestamp id 0
(...)
Notice that in this new usage pattern, a non-congested port should
basically use timestamp ID 0 all the time, progressing to higher numbers
only if there are unacknowledged timestamps in flight. Compare this to
the old usage, where the timestamp ID used to monotonically increase
modulo OCELOT_MAX_PTP_ID.
In terms of implementation, this simplifies the bookkeeping of the
ocelot_port :: ts_id and ptp_skbs_in_flight. Since we need to traverse
the list of two-step timestampable skbs for each new packet anyway, the
information can already be computed and does not need to be stored.
Also, ocelot_port->tx_skbs is always accessed under the switch-wide
ocelot->ts_id_lock IRQ-unsafe spinlock, so we don't need the skb queue's
lock and can use the unlocked primitives safely.
This problem was actually detected using the tc-taprio offload, and is
causing trouble in TSN scenarios, which Felix (NXP LS1028A / VSC9959)
supports but Ocelot (VSC7514) does not. Thus, I've selected the commit
to blame as the one adding initial timestamping support for the Felix
switch.
Fixes: c0bcf537667c ("net: dsa: ocelot: add hardware timestamping support for Felix")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241205145519.1236778-5-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ocelot_get_txtstamp() is a threaded IRQ handler, requested explicitly as
such by both ocelot_ptp_rdy_irq_handler() and vsc9959_irq_handler().
As such, it runs with IRQs enabled, and not in hardirq context. Thus,
ocelot_port_add_txtstamp_skb() has no reason to turn off IRQs, it cannot
be preempted by ocelot_get_txtstamp(). For the same reason,
dev_kfree_skb_any_reason() will always evaluate as kfree_skb_reason() in
this calling context, so just simplify the dev_kfree_skb_any() call to
kfree_skb().
Also, ocelot_port_txtstamp_request() runs from NET_TX softirq context,
not with hardirqs enabled. Thus, ocelot_get_txtstamp() which shares the
ocelot_port->tx_skbs.lock lock with it, has no reason to disable hardirqs.
This is part of a larger rework of the TX timestamping procedure.
A logical subportion of the rework has been split into a separate
change.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241205145519.1236778-4-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This condition, theoretically impossible to trigger, is not really
handled well. By "continuing", we are skipping the write to SYS_PTP_NXT
which advances the timestamp FIFO to the next entry. So we are reading
the same FIFO entry all over again, printing stack traces and eventually
killing the kernel.
No real problem has been observed here. This is part of a larger rework
of the timestamp IRQ procedure, with this logical change split out into
a patch of its own. We will need to "goto next_ts" for other conditions
as well.
Fixes: 9fde506e0c53 ("net: mscc: ocelot: warn when a PTP IRQ is raised for an unknown skb")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241205145519.1236778-3-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If ocelot_port_add_txtstamp_skb() fails, for example due to a full PTP
timestamp FIFO, we must undo the skb_clone_sk() call with kfree_skb().
Otherwise, the reference to the skb clone is lost.
Fixes: 52849bcf0029 ("net: mscc: ocelot: avoid overflowing the PTP timestamp FIFO")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241205145519.1236778-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
syzkaller reported a warning in __sk_skb_reason_drop().
Commit 61b95c70f344 ("net: ip: make ip_route_input_rcu() return
drop reasons") missed a path where -EINVAL is returned.
Then, the cited commit started to trigger the warning with the
invalid error.
Let's fix it by returning SKB_DROP_REASON_NOT_SPECIFIED.
[0]:
WARNING: CPU: 0 PID: 10 at net/core/skbuff.c:1216 __sk_skb_reason_drop net/core/skbuff.c:1216 [inline]
WARNING: CPU: 0 PID: 10 at net/core/skbuff.c:1216 sk_skb_reason_drop+0x97/0x1b0 net/core/skbuff.c:1241
Modules linked in:
CPU: 0 UID: 0 PID: 10 Comm: kworker/0:1 Not tainted 6.12.0-10686-gbb18265c3aba #10 1c308307628619808b5a4a0495c4aab5637b0551
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014
Workqueue: wg-crypt-wg2 wg_packet_decrypt_worker
RIP: 0010:__sk_skb_reason_drop net/core/skbuff.c:1216 [inline]
RIP: 0010:sk_skb_reason_drop+0x97/0x1b0 net/core/skbuff.c:1241
Code: 5d 41 5c 41 5d 41 5e e9 e7 9e 95 fd e8 e2 9e 95 fd 31 ff 44 89 e6 e8 58 a1 95 fd 45 85 e4 0f 85 a2 00 00 00 e8 ca 9e 95 fd 90 <0f> 0b 90 e8 c1 9e 95 fd 44 89 e6 bf 01 00 00 00 e8 34 a1 95 fd 41
RSP: 0018:ffa0000000007650 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 000000000000ffff RCX: ffffffff83bc3592
RDX: ff110001002a0000 RSI: ffffffff83bc34d6 RDI: 0000000000000007
RBP: ff11000109ee85f0 R08: 0000000000000001 R09: ffe21c00213dd0da
R10: 000000000000ffff R11: 0000000000000000 R12: 00000000ffffffea
R13: 0000000000000000 R14: ff11000109ee86d4 R15: ff11000109ee8648
FS: 0000000000000000(0000) GS:ff1100011a000000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020177000 CR3: 0000000108a3d006 CR4: 0000000000771ef0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe07f0 DR7: 0000000000000600
PKRU: 55555554
Call Trace:
<IRQ>
kfree_skb_reason include/linux/skbuff.h:1263 [inline]
ip_rcv_finish_core.constprop.0+0x896/0x2320 net/ipv4/ip_input.c:424
ip_list_rcv_finish.constprop.0+0x1b2/0x710 net/ipv4/ip_input.c:610
ip_sublist_rcv net/ipv4/ip_input.c:636 [inline]
ip_list_rcv+0x34a/0x460 net/ipv4/ip_input.c:670
__netif_receive_skb_list_ptype net/core/dev.c:5715 [inline]
__netif_receive_skb_list_core+0x536/0x900 net/core/dev.c:5762
__netif_receive_skb_list net/core/dev.c:5814 [inline]
netif_receive_skb_list_internal+0x77c/0xdc0 net/core/dev.c:5905
gro_normal_list include/net/gro.h:515 [inline]
gro_normal_list include/net/gro.h:511 [inline]
napi_complete_done+0x219/0x8c0 net/core/dev.c:6256
wg_packet_rx_poll+0xbff/0x1e40 drivers/net/wireguard/receive.c:488
__napi_poll.constprop.0+0xb3/0x530 net/core/dev.c:6877
napi_poll net/core/dev.c:6946 [inline]
net_rx_action+0x9eb/0xe30 net/core/dev.c:7068
handle_softirqs+0x1ac/0x740 kernel/softirq.c:554
do_softirq kernel/softirq.c:455 [inline]
do_softirq+0x48/0x80 kernel/softirq.c:442
</IRQ>
<TASK>
__local_bh_enable_ip+0xed/0x110 kernel/softirq.c:382
spin_unlock_bh include/linux/spinlock.h:396 [inline]
ptr_ring_consume_bh include/linux/ptr_ring.h:367 [inline]
wg_packet_decrypt_worker+0x3ba/0x580 drivers/net/wireguard/receive.c:499
process_one_work+0x940/0x1a70 kernel/workqueue.c:3229
process_scheduled_works kernel/workqueue.c:3310 [inline]
worker_thread+0x639/0xe30 kernel/workqueue.c:3391
kthread+0x283/0x350 kernel/kthread.c:389
ret_from_fork+0x45/0x80 arch/x86/kernel/process.c:147
ret_from_fork_asm+0x11/0x20 arch/x86/entry/entry_64.S:244
</TASK>
Fixes: 82d9983ebeb8 ("net: ip: make ip_route_input_noref() return drop reasons")
Reported-by: syzkaller <syzkaller@googlegroups.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/20241206020715.80207-1-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 66600fac7a98 ("net: stmmac: TSO: Fix unbalanced DMA map/unmap
for non-paged SKB data") moved the assignment of tx_skbuff_dma[]'s
members to be later in stmmac_tso_xmit().
The buf (dma cookie) and len stored in this structure are passed to
dma_unmap_single() by stmmac_tx_clean(). The DMA API requires that
the dma cookie passed to dma_unmap_single() is the same as the value
returned from dma_map_single(). However, by moving the assignment
later, this is not the case when priv->dma_cap.addr64 > 32 as "des"
is offset by proto_hdr_len.
This causes problems such as:
dwc-eth-dwmac 2490000.ethernet eth0: Tx DMA map failed
and with DMA_API_DEBUG enabled:
DMA-API: dwc-eth-dwmac 2490000.ethernet: device driver tries to +free DMA memory it has not allocated [device address=0x000000ffffcf65c0] [size=66 bytes]
Fix this by maintaining "des" as the original DMA cookie, and use
tso_des to pass the offset DMA cookie to stmmac_tso_allocator().
Full details of the crashes can be found at:
https://lore.kernel.org/all/d8112193-0386-4e14-b516-37c2d838171a@nvidia.com/
https://lore.kernel.org/all/klkzp5yn5kq5efgtrow6wbvnc46bcqfxs65nz3qy77ujr5turc@bwwhelz2l4dw/
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Reported-by: Thierry Reding <thierry.reding@gmail.com>
Fixes: 66600fac7a98 ("net: stmmac: TSO: Fix unbalanced DMA map/unmap for non-paged SKB data")
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Furong Xu <0x1207@gmail.com>
Link: https://patch.msgid.link/E1tJXcx-006N4Z-PC@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Ilya reported a slab-use-after-free in dst_destroy [1]
Issue is in xfrm6_net_init() and xfrm4_net_init() :
They copy xfrm[46]_dst_ops_template into net->xfrm.xfrm[46]_dst_ops.
But net structure might be freed before all the dst callbacks are
called. So when dst_destroy() calls later :
if (dst->ops->destroy)
dst->ops->destroy(dst);
dst->ops points to the old net->xfrm.xfrm[46]_dst_ops, which has been freed.
See a relevant issue fixed in :
ac888d58869b ("net: do not delay dst_entries_add() in dst_release()")
A fix is to queue the 'struct net' to be freed after one
another cleanup_net() round (and existing rcu_barrier())
[1]
BUG: KASAN: slab-use-after-free in dst_destroy (net/core/dst.c:112)
Read of size 8 at addr ffff8882137ccab0 by task swapper/37/0
Dec 03 05:46:18 kernel:
CPU: 37 UID: 0 PID: 0 Comm: swapper/37 Kdump: loaded Not tainted 6.12.0 #67
Hardware name: Red Hat KVM/RHEL, BIOS 1.16.1-1.el9 04/01/2014
Call Trace:
<IRQ>
dump_stack_lvl (lib/dump_stack.c:124)
print_address_description.constprop.0 (mm/kasan/report.c:378)
? dst_destroy (net/core/dst.c:112)
print_report (mm/kasan/report.c:489)
? dst_destroy (net/core/dst.c:112)
? kasan_addr_to_slab (mm/kasan/common.c:37)
kasan_report (mm/kasan/report.c:603)
? dst_destroy (net/core/dst.c:112)
? rcu_do_batch (kernel/rcu/tree.c:2567)
dst_destroy (net/core/dst.c:112)
rcu_do_batch (kernel/rcu/tree.c:2567)
? __pfx_rcu_do_batch (kernel/rcu/tree.c:2491)
? lockdep_hardirqs_on_prepare (kernel/locking/lockdep.c:4339 kernel/locking/lockdep.c:4406)
rcu_core (kernel/rcu/tree.c:2825)
handle_softirqs (kernel/softirq.c:554)
__irq_exit_rcu (kernel/softirq.c:589 kernel/softirq.c:428 kernel/softirq.c:637)
irq_exit_rcu (kernel/softirq.c:651)
sysvec_apic_timer_interrupt (arch/x86/kernel/apic/apic.c:1049 arch/x86/kernel/apic/apic.c:1049)
</IRQ>
<TASK>
asm_sysvec_apic_timer_interrupt (./arch/x86/include/asm/idtentry.h:702)
RIP: 0010:default_idle (./arch/x86/include/asm/irqflags.h:37 ./arch/x86/include/asm/irqflags.h:92 arch/x86/kernel/process.c:743)
Code: 00 4d 29 c8 4c 01 c7 4c 29 c2 e9 6e ff ff ff 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 66 90 0f 00 2d c7 c9 27 00 fb f4 <fa> c3 cc cc cc cc 66 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 90
RSP: 0018:ffff888100d2fe00 EFLAGS: 00000246
RAX: 00000000001870ed RBX: 1ffff110201a5fc2 RCX: ffffffffb61a3e46
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffffffffb3d4d123
RBP: 0000000000000000 R08: 0000000000000001 R09: ffffed11c7e1835d
R10: ffff888e3f0c1aeb R11: 0000000000000000 R12: 0000000000000000
R13: ffff888100d20000 R14: dffffc0000000000 R15: 0000000000000000
? ct_kernel_exit.constprop.0 (kernel/context_tracking.c:148)
? cpuidle_idle_call (kernel/sched/idle.c:186)
default_idle_call (./include/linux/cpuidle.h:143 kernel/sched/idle.c:118)
cpuidle_idle_call (kernel/sched/idle.c:186)
? __pfx_cpuidle_idle_call (kernel/sched/idle.c:168)
? lock_release (kernel/locking/lockdep.c:467 kernel/locking/lockdep.c:5848)
? lockdep_hardirqs_on_prepare (kernel/locking/lockdep.c:4347 kernel/locking/lockdep.c:4406)
? tsc_verify_tsc_adjust (arch/x86/kernel/tsc_sync.c:59)
do_idle (kernel/sched/idle.c:326)
cpu_startup_entry (kernel/sched/idle.c:423 (discriminator 1))
start_secondary (arch/x86/kernel/smpboot.c:202 arch/x86/kernel/smpboot.c:282)
? __pfx_start_secondary (arch/x86/kernel/smpboot.c:232)
? soft_restart_cpu (arch/x86/kernel/head_64.S:452)
common_startup_64 (arch/x86/kernel/head_64.S:414)
</TASK>
Dec 03 05:46:18 kernel:
Allocated by task 12184:
kasan_save_stack (mm/kasan/common.c:48)
kasan_save_track (./arch/x86/include/asm/current.h:49 mm/kasan/common.c:60 mm/kasan/common.c:69)
__kasan_slab_alloc (mm/kasan/common.c:319 mm/kasan/common.c:345)
kmem_cache_alloc_noprof (mm/slub.c:4085 mm/slub.c:4134 mm/slub.c:4141)
copy_net_ns (net/core/net_namespace.c:421 net/core/net_namespace.c:480)
create_new_namespaces (kernel/nsproxy.c:110)
unshare_nsproxy_namespaces (kernel/nsproxy.c:228 (discriminator 4))
ksys_unshare (kernel/fork.c:3313)
__x64_sys_unshare (kernel/fork.c:3382)
do_syscall_64 (arch/x86/entry/common.c:52 arch/x86/entry/common.c:83)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130)
Dec 03 05:46:18 kernel:
Freed by task 11:
kasan_save_stack (mm/kasan/common.c:48)
kasan_save_track (./arch/x86/include/asm/current.h:49 mm/kasan/common.c:60 mm/kasan/common.c:69)
kasan_save_free_info (mm/kasan/generic.c:582)
__kasan_slab_free (mm/kasan/common.c:271)
kmem_cache_free (mm/slub.c:4579 mm/slub.c:4681)
cleanup_net (net/core/net_namespace.c:456 net/core/net_namespace.c:446 net/core/net_namespace.c:647)
process_one_work (kernel/workqueue.c:3229)
worker_thread (kernel/workqueue.c:3304 kernel/workqueue.c:3391)
kthread (kernel/kthread.c:389)
ret_from_fork (arch/x86/kernel/process.c:147)
ret_from_fork_asm (arch/x86/entry/entry_64.S:257)
Dec 03 05:46:18 kernel:
Last potentially related work creation:
kasan_save_stack (mm/kasan/common.c:48)
__kasan_record_aux_stack (mm/kasan/generic.c:541)
insert_work (./include/linux/instrumented.h:68 ./include/asm-generic/bitops/instrumented-non-atomic.h:141 kernel/workqueue.c:788 kernel/workqueue.c:795 kernel/workqueue.c:2186)
__queue_work (kernel/workqueue.c:2340)
queue_work_on (kernel/workqueue.c:2391)
xfrm_policy_insert (net/xfrm/xfrm_policy.c:1610)
xfrm_add_policy (net/xfrm/xfrm_user.c:2116)
xfrm_user_rcv_msg (net/xfrm/xfrm_user.c:3321)
netlink_rcv_skb (net/netlink/af_netlink.c:2536)
xfrm_netlink_rcv (net/xfrm/xfrm_user.c:3344)
netlink_unicast (net/netlink/af_netlink.c:1316 net/netlink/af_netlink.c:1342)
netlink_sendmsg (net/netlink/af_netlink.c:1886)
sock_write_iter (net/socket.c:729 net/socket.c:744 net/socket.c:1165)
vfs_write (fs/read_write.c:590 fs/read_write.c:683)
ksys_write (fs/read_write.c:736)
do_syscall_64 (arch/x86/entry/common.c:52 arch/x86/entry/common.c:83)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130)
Dec 03 05:46:18 kernel:
Second to last potentially related work creation:
kasan_save_stack (mm/kasan/common.c:48)
__kasan_record_aux_stack (mm/kasan/generic.c:541)
insert_work (./include/linux/instrumented.h:68 ./include/asm-generic/bitops/instrumented-non-atomic.h:141 kernel/workqueue.c:788 kernel/workqueue.c:795 kernel/workqueue.c:2186)
__queue_work (kernel/workqueue.c:2340)
queue_work_on (kernel/workqueue.c:2391)
__xfrm_state_insert (./include/linux/workqueue.h:723 net/xfrm/xfrm_state.c:1150 net/xfrm/xfrm_state.c:1145 net/xfrm/xfrm_state.c:1513)
xfrm_state_update (./include/linux/spinlock.h:396 net/xfrm/xfrm_state.c:1940)
xfrm_add_sa (net/xfrm/xfrm_user.c:912)
xfrm_user_rcv_msg (net/xfrm/xfrm_user.c:3321)
netlink_rcv_skb (net/netlink/af_netlink.c:2536)
xfrm_netlink_rcv (net/xfrm/xfrm_user.c:3344)
netlink_unicast (net/netlink/af_netlink.c:1316 net/netlink/af_netlink.c:1342)
netlink_sendmsg (net/netlink/af_netlink.c:1886)
sock_write_iter (net/socket.c:729 net/socket.c:744 net/socket.c:1165)
vfs_write (fs/read_write.c:590 fs/read_write.c:683)
ksys_write (fs/read_write.c:736)
do_syscall_64 (arch/x86/entry/common.c:52 arch/x86/entry/common.c:83)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130)
Fixes: a8a572a6b5f2 ("xfrm: dst_entries_init() per-net dst_ops")
Reported-by: Ilya Maximets <i.maximets@ovn.org>
Closes: https://lore.kernel.org/netdev/CANn89iKKYDVpB=MtmfH7nyv2p=rJWSLedO5k7wSZgtY_tO8WQg@mail.gmail.com/T/#m02c98c3009fe66382b73cfb4db9cf1df6fab3fbf
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20241204125455.3871859-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
Jesse Van Gavere
Nikita Yushchenko
Daniel Borkmann
Martin Ottens
Vladimir Oltean
Frederik Deweerdt
Daniele Palmas
Maxim Levitsky
Simon Horman
Florian Westphal
Phil Sutter
MoYuanhao
Petr Machata
Michael Chan
Paolo Abeni
Koichiro Den
Geetha sowjanya
Stefan Wahren
Anumula Murali Mohan Reddy
Daniel Machon
Dan Carpenter
Kuniyuki Iwashima
Russell King (Oracle)
Eric Dumazet