Age | Commit message (Collapse) | Author | Files | Lines |
|
Xiumei reported a bug with espintcp over IPv6 in transport mode,
because xfrm6_transport_finish expects to find IP6CB data (struct
inet6_skb_cb). Currently, espintcp zeroes the CB, but the relevant
part is actually preserved by previous layers (first set up by tcp,
then strparser only zeroes a small part of tcp_skb_tb), so we can just
relocate it to the start of skb->cb.
Fixes: e27cca96cd68 ("xfrm: add espintcp (RFC 8229)")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
If CONFIG_INET_XFRM_TUNNEL is set but CONFIG_IPV6 is n,
net/ipv4/ip_vti.c:493:27: warning: 'vti_ipip6_handler' defined but not used [-Wunused-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
Trying to use ktls on a system with 32-bit userspace and 64-bit kernel
results in a EOPNOTSUPP message during sendmsg:
setsockopt(3, SOL_TLS, TLS_TX, …, 40) = 0
sendmsg(3, …, msg_flags=0}, 0) = -1 EOPNOTSUPP (Operation not supported)
The tls_sw implementation does strict flag checking and does not allow
the MSG_CMSG_COMPAT flag, which is set if the message comes in through
the compat syscall.
This patch adds MSG_CMSG_COMPAT to the flag check to allow the usage of
the TLS SW implementation on systems using the compat syscall path.
Note that the same check is present in the sendmsg path for the TLS
device implementation, however the flag hasn't been added there for lack
of testing hardware.
Signed-off-by: Rouven Czerwinski <r.czerwinski@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With commit b93df08ccda3 ("mptcp: explicitly track the fully
established status"), the status of unaccepted mptcp closed in
mptcp_sock_destruct() changes from TCP_SYN_RECV to TCP_ESTABLISHED.
As a result mptcp_sock_destruct() does not perform the proper
cleanup and inet_sock_destruct() will later emit a warn.
Address the issue updating the condition tested in mptcp_sock_destruct().
Also update the related comment.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/66
Reported-and-tested-by: Christoph Paasch <cpaasch@apple.com>
Fixes: b93df08ccda3 ("mptcp: explicitly track the fully established status")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During diag self-tests we introduce long wait in the mptcp test
program to give the script enough time to access the sockets
dump.
Such wait is introduced after shutting down one sockets end. Since
commit 43b54c6ee382 ("mptcp: Use full MPTCP-level disconnect state
machine") if both sides shutdown the socket is correctly transitioned
into CLOSED status.
As a side effect some sockets are not dumped via the diag interface,
because the socket state (CLOSED) does not match the default filter, and
this cause self-tests instability.
Address the issue moving the above mentioned wait before shutting
down the socket.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/68
Fixes: df62f2ec3df6 ("selftests/mptcp: add diag interface tests")
Tested-and-acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit df62f2ec3df6 ("selftests/mptcp: add diag interface tests")
the MPTCP selftests relies on the MPTCP diag interface which is
enabled by a specific kconfig knob: be sure to include it.
Fixes: df62f2ec3df6 ("selftests/mptcp: add diag interface tests")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Query the USB device's device tree node when looking for a MAC address.
The struct device embedded into the struct net_device does not have a
device tree node attached at all.
The reason why this went unnoticed is because the system where this was
tested was one of the few development units that had its OTP programmed,
as opposed to production systems where the MAC address is stored in a
separate EEPROM and is passed via device tree by the firmware.
Reported-by: EJ Hsu <ejh@nvidia.com>
Fixes: acb6d3771a03 ("r8152: Use MAC address from device tree if available")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: EJ Hsu <ejh@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drop repeated words in kernel/bpf/: {has, the}
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200807033141.10437-1-rdunlap@infradead.org
|
|
99aacebecb75 ("selftests: do not use .ONESHELL") removed .ONESHELL, which
changes how Makefile "silences" multi-command target recipes. selftests/bpf's
Makefile relied (a somewhat unknowingly) on .ONESHELL behavior of silencing
all commands within the recipe if the first command contains @ symbol.
Removing .ONESHELL exposed this hack.
This patch fixes the issue by explicitly silencing each command with $(Q).
Also explicitly define fallback rule for building *.o from *.c, instead of
relying on non-silent inherited rule. This was causing a non-silent output for
bench.o object file.
Fixes: 92f7440ecc93 ("selftests/bpf: More succinct Makefile output")
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200807033058.848677-1-andriin@fb.com
|
|
The BPF helper bpf_trace_printk() no longer uses trace_printk();
it is now triggers a dedicated trace event. Hence the described
warning is no longer present, so remove the discussion of it as
it may confuse people.
Fixes: ac5a72ea5c89 ("bpf: Use dedicated bpf_trace_printk event instead of trace_printk()")
Signed-off-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/1596801029-32395-1-git-send-email-alan.maguire@oracle.com
|
|
1. Added a skb->len check
This driver expects upper layers to include a pseudo header of 1 byte
when passing down a skb for transmission. This driver will read this
1-byte header. This patch added a skb->len check before reading the
header to make sure the header exists.
2. Changed to use needed_headroom instead of hard_header_len to request
necessary headroom to be allocated
In net/packet/af_packet.c, the function packet_snd first reserves a
headroom of length (dev->hard_header_len + dev->needed_headroom).
Then if the socket is a SOCK_DGRAM socket, it calls dev_hard_header,
which calls dev->header_ops->create, to create the link layer header.
If the socket is a SOCK_RAW socket, it "un-reserves" a headroom of
length (dev->hard_header_len), and assumes the user to provide the
appropriate link layer header.
So according to the logic of af_packet.c, dev->hard_header_len should
be the length of the header that would be created by
dev->header_ops->create.
However, this driver doesn't provide dev->header_ops, so logically
dev->hard_header_len should be 0.
So we should use dev->needed_headroom instead of dev->hard_header_len
to request necessary headroom to be allocated.
This change fixes kernel panic when this driver is used with AF_PACKET
SOCK_RAW sockets.
Call stack when panic:
[ 168.399197] skbuff: skb_under_panic: text:ffffffff819d95fb len:20
put:14 head:ffff8882704c0a00 data:ffff8882704c09fd tail:0x11 end:0xc0
dev:veth0
...
[ 168.399255] Call Trace:
[ 168.399259] skb_push.cold+0x14/0x24
[ 168.399262] eth_header+0x2b/0xc0
[ 168.399267] lapbeth_data_transmit+0x9a/0xb0 [lapbether]
[ 168.399275] lapb_data_transmit+0x22/0x2c [lapb]
[ 168.399277] lapb_transmit_buffer+0x71/0xb0 [lapb]
[ 168.399279] lapb_kick+0xe3/0x1c0 [lapb]
[ 168.399281] lapb_data_request+0x76/0xc0 [lapb]
[ 168.399283] lapbeth_xmit+0x56/0x90 [lapbether]
[ 168.399286] dev_hard_start_xmit+0x91/0x1f0
[ 168.399289] ? irq_init_percpu_irqstack+0xc0/0x100
[ 168.399291] __dev_queue_xmit+0x721/0x8e0
[ 168.399295] ? packet_parse_headers.isra.0+0xd2/0x110
[ 168.399297] dev_queue_xmit+0x10/0x20
[ 168.399298] packet_sendmsg+0xbf0/0x19b0
......
Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Cc: Martin Schiller <ms@dev.tdt.de>
Cc: Brian Norris <briannorris@chromium.org>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clang compiler version: 12.0.0
The following warning appears during the selftests/bpf compilation:
prog_tests/send_signal.c:51:3: warning: ignoring return value of ‘write’,
declared with attribute warn_unused_result [-Wunused-result]
51 | write(pipe_c2p[1], buf, 1);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
prog_tests/send_signal.c:54:3: warning: ignoring return value of ‘read’,
declared with attribute warn_unused_result [-Wunused-result]
54 | read(pipe_p2c[0], buf, 1);
| ^~~~~~~~~~~~~~~~~~~~~~~~~
......
prog_tests/stacktrace_build_id_nmi.c:13:2: warning: ignoring return value
of ‘fscanf’,declared with attribute warn_unused_result [-Wunused-resul]
13 | fscanf(f, "%llu", &sample_freq);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
test_tcpnotify_user.c:133:2: warning:ignoring return value of ‘system’,
declared with attribute warn_unused_result [-Wunused-result]
133 | system(test_script);
| ^~~~~~~~~~~~~~~~~~~
test_tcpnotify_user.c:138:2: warning:ignoring return value of ‘system’,
declared with attribute warn_unused_result [-Wunused-result]
138 | system(test_script);
| ^~~~~~~~~~~~~~~~~~~
test_tcpnotify_user.c:143:2: warning:ignoring return value of ‘system’,
declared with attribute warn_unused_result [-Wunused-result]
143 | system(test_script);
| ^~~~~~~~~~~~~~~~~~~
Add code that fix compilation warning about ignoring return value and
handles any errors; Check return value of library`s API make the code
more secure.
Signed-off-by: Jianlin Lv <Jianlin.Lv@arm.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200806104224.95306-1-Jianlin.Lv@arm.com
|