| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch contains the generated header file of the following
change "drm/msm/mdp5: Get SMP client list from mdp5_cfg".
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
MDP block is actually contained inside the MDSS block. For some
chipsets, the base address of the MDP registers is different from the
current (assumed) 0x100 offset.
Like CTL and LM blocks, this changes introduce a dynamic offset
for the MDP instance, which can be found out at runtime, once the
MDSS HW version is read.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
This change contains the generated header file for the following
change "drm/msm/mdp5: Separate MDP5 domain from MDSS domain".
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Prepare for initial DSI implementation
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
The width and height in SSPP_SRC_IMG_SIZE register should be the
size of the entire source framebuffer, not the fetch size.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
This change adds the registers in mdp5 ping pong blocks
and split display control registers.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Pingpong register base addresses are different across platforms.
This change adds this information to config table and initialize
the values for 8x74 and 8084.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Up until now, we assume that eDP is tight to intf_0 and HDMI to
intf_3. This information shall actually come from the mdp5_cfg
module since it can change from one chip to another.
v2: rename macro to mdp5_cfg_intf_is_virtual() [pointed by Archit]
v3: add sanity check before writing in INTF_TIMING_ENGINE_EN registers
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Some interfaces (WB, DSI Command Mode) need to be kicked off
through a START Signal. This signal needs to be sent at the right
time and requests in some cases to keep track of the pipeline
status (eg: whether pipeline registers are flushed AND output WB
buffers are ready, in case of WB interface).
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
DSI and WB interfaces need a more complex pipeline configuration
than the current mdp5_ctl_set_intf().
For example, memory output connections need to be selected for
WB. Interface mode (Video vs. Command modes) also need to be
configured for DSI.
This change takes care of configuring the whole pipeline as far
as operation mode goes. DSI and WB interfaces will be added
later.
v2: rename macro to mdp5_cfg_intf_is_virtual() [pointed by Archit]
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
[Remove temp bisectability hack -Rob]
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Prepare for pipeline operation mode configuration, in particular
for DSI and WB modes.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
[Throw in a #define temporarily to keep things bisectable -Rob]
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
MDP5 hardware has some limitation and requires to avoid flushing
registers more than once between two Vblanks.
This change removes all FLUSH operations (except for HW cursor)
beside the one coming from a CRTC's ->atomic_flush().
This avoid this type of behavior (eg: CRTC + 1 plane overlay):
[drm:mdp5_crtc_vblank_irq] vblank
[drm:mdp5_ctl_commit] flush (20048) CTL + LM0 + RGB0
[drm:mdp5_ctl_commit] flush (20040) CTL + LM0
[drm:mdp5_crtc_vblank_irq] blank
[drm:mdp5_ctl_commit] flush (20049) CTL + LM0 + RGB0 + VIG0
[drm:mdp5_crtc_vblank_irq] blank
and replaces it by:
[drm:mdp5_crtc_vblank_irq] vblank
[drm:mdp5_ctl_commit] flush (20048) CTL + LM0 + RGB0
[drm:mdp5_crtc_vblank_irq] blank
[drm:mdp5_ctl_commit] flush (20049) CTL + LM0 + RGB0 + VIG0
[drm:mdp5_crtc_vblank_irq] blank
Only *one* FLUSH is called between Vblanks interrupts.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Add support to use the VRAM carveout (if specified in dtb) for fbdev
scanout buffer. This allows drm/msm to take over a bootloader splash-
screen, and avoids corruption on screen that results if the kernel uses
memory that is still being scanned out for itself.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
We'll want to extend this a bit to handle also a reserved-memory
("stolen") region, so that drm/msm can take-over bootloader splash
screen. First split it out into it's own fxn to reduce noise in
the following patch.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
qemu and simics simulators both seem to expect that video should be disabled
before changing the video mode.
references:
http://git.qemu.org/?p=qemu.git;a=blob;f=hw/display/vga.c;h=c0f7b343bbab586c8593d29c7a765f1e6ca3662c;hb=HEAD#l727
http://wiki.osdev.org/Bochs_VBE_Extensions#Setting_display_resolution_and_bit_depth
Signed-off-by: Chris Ruffin <chris.ruffin@intel.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Improve the readability and keeps the lines shorter than 80 columns.
Signed-off-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Consistently with other free functions, handle the NULL case without
oopsing.
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Users of the atomic state assume that if the pointer to a crtc, plane or
connector is not NULL in the respective object vector, than the state
for that object in *_states vector also won't be NULL. That assumption
was broken by drm_atomic_state_clear(), which would clear the state
pointer but leave the pointer to the object still set.
This fixes a NULL pointer dereference in i915 caused by the use of
drm_atomic_state_clear().
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
|
|
The UART reference clock speed is 7273.8 kHz, not 72738 kHz.
Dots aren't usually used in node names even though ePAPR permits
them. However, this can easily be avoided by expressing the
frequency in Hz, not kHz.
This patch changes the name to refclk7273800hz, reflecting the
actual clock speed.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Use the same logic when checking for valid ioctl range in
drm_ioctl_flags() that is used in drm_ioctl() to avoid
confusion.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Use max() to make the code to determine the allocation size for
the ioctl data easier to read.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Now that cmd_drv is gone the handling for core and driver ioctls is
mostly identical, so eliminate the duplication. Also take the
opportunity to simplify the range checks to be less cluttered.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
ioctl->cmd_drv is pointless and we can just as well stick the full ioctl
definition into ioctl->cmd.
Cc: Jakob Bornecrantz <jakob@vmware.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Currently DRM_IOCTL_DEF_DRV does '[DRM_IOCTL_NR(DRM_##ioctl)]' which
doesn't make much sense since DRM_##ioctl is already a the raw ioctl
number. So change it to 'DRM_IOCTL_NR(DRM_IOCTL_##ioctl) - DRM_COMMAND_BASE'
which means the DRM_IOCTL_NR() now makes sense, and also this also means
if there's a mistake in the DRM_IOCTL_##ioctl macros we might get a
warning about it (eg. we would have gotten a sparse warning about the
i915 colorkey get/set ioctl being defined to be the same thing).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Since
commit 17cabf571e50677d980e9ab2a43c5f11213003ae
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Wed Jan 14 11:20:57 2015 +0000
drm/i915: Trim the command parser allocations
we may then try to allocate a zero-sized object and attempt to extract
its pages. Understandably this fails.
Testcase: igt/gem_exec_nop #ivb,byt,hsw
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The return value of one of the calls to drm_atomic_get_connector_state()
in intel_modeset_stage_output_state() wasn't checked for errors.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
To allow for views where the view type is not defined by the view type only,
like it is in stereo or rotated 90 degree view, change the semantic to require
the whole view structure for comparison when we match a GGTT view.
This allows including parameters like offset to be included in the view which
is useful for eg. partial views.
v3:
- Rely on ggtt_view type being 0 for non-GGTT vma's, which equals to
I915_GGTT_VIEW_NORMAL. (Daniel Vetter)
- Do not use potentially slower comparison when we only want to know if
something is or is not a normal view.
- Rebase on top of rotated view patches. Add rotated view singleton.
- If one view is missing in comparison they're equal only if both are missing.
v4:
- Use comparison helper in obj_to_ggtt_view too. (Tvrtko Ursulin)
- Do WARN_ON if one view is NULL. (Tvrtko Ursulin)
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
drivers/gpu/drm/i915/i915_gem_gtt.c:1349:1-4: WARNING: end returns can be simpified and declaration on line 1347 can be dropped
Simplify a trivial if-return sequence. Possibly combine with a
preceding function call.
Generated by: scripts/coccinelle/misc/simple_return.cocci
CC: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Legacy setCrtc has a nice fastpath for just updating the frontbuffer
when the output routing doesn't change. Which I of course tried to
keep working, except that I fumbled the job: The helpers correctly
compute ->mode_changed, CRTC updates get correctly skipped but
connector functions are called unconditionally.
Fix this.
v2: For the disable sided connector->state->crtc might be NULL.
Instead look at the old_connector_state->crtc, but still use the new
crtc state for that old crtc. Reported by Thierry.
Reported-and-Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> (v1)
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
This is useful for writing igts to make sure we don't break this,
without being forced to own a one of these dinosaurs.
Suggested-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Some of the crtc_compute_clock() still depended on encoder->new_crtc
since they didn't use intel_pipe_will_have_type() and used an open
coded version of that function instead. This patch replaces those with
the appropriate code that checks the atomic state intead.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
[danvet: Separate the if (!connector) continue to facility easier
extraction of a loop iterator for all of these (there's lots more in
i915 and atomic helpers).]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The function intel_dp_set_drrs_state() would decide which pipe to
downclock based on the staged config for the given connector. However,
the result of that function is immediate, and it uses input values from
crtc->config, so it should be looking at the current crtc instead.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Pass a crtc_state to it and find whether the pipe has an encoder of a
given type by looking at the drm_atomic_state the crtc_state points to.
Until recently i9xx_get_refclk() used to be called indirectly from
vlv_force_pll_on() with a dummy crtc_state. That dummy crtc state is not
converted to be part of a full drm atomic state, so add a WARN in case
someone decides to call that again with a such dummy state. This was
removed in
commit 9cbe40c15a753e02f5da16f6de901decf3276cf1
Author: Vijay Purushothaman <vijay.a.purushothaman@linux.intel.com>
Date: Thu Mar 5 19:33:08 2015 +0530
drm/i915: Update prop, int co-eff and gain threshold for CHV
v2: Warn if there is no connectors for a given crtc. (Daniel)
Replace comment i9xx_get_refclk() with a WARN_ON(). (Ander)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
[danvet: Add commit reference for when i9xx_get_refclk was removed.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Follow up patches will convert some functions called from there to use
the atomic state, instead of directly accessing the new or current
config. This patch just changes the parameters, but shouldn't have any
functional changes.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Traces for page directories and tables allocation and map.
v2: Removed references to teardown.
v3: bitmap_scnprintf has been deprecated.
v4: Replace bitmap_scnprintf with scnprintf correctly, and get right
range lengths. (Mika)
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This patch continues on the idea from "Track GEN6 page table usage".
From here on, in the steady state, PDEs are all pointing to the scratch
page table (as recommended in the spec). When an object is allocated in
the VA range, the code will determine if we need to allocate a page for
the page table. Similarly when the object is destroyed, we will remove,
and free the page table pointing the PDE back to the scratch page.
Following patches will work to unify the code a bit as we bring in GEN8
support. GEN6 and GEN8 are different enough that I had a hard time to
get to this point with as much common code as I do.
The aliasing PPGTT must pre-allocate all of the page tables. There are a
few reasons for this. Two trivial ones: aliasing ppgtt goes through the
ggtt paths, so it's hard to maintain, we currently do not restore the
default context (assuming the previous force reload is indeed
necessary). Most importantly though, the only way (it seems from
empirical evidence) to invalidate the CS TLBs on non-render ring is to
either use ring sync (which requires actually stopping the rings in
order to synchronize when the sync completes vs. where you are in
execution), or to reload DCLV. Since without full PPGTT we do not ever
reload the DCLV register, there is no good way to achieve this. The
simplest solution is just to not support dynamic page table
creation/destruction in the aliasing PPGTT.
We could always reload DCLV, but this seems like quite a bit of excess
overhead only to save at most 2MB-4k of memory for the aliasing PPGTT
page tables.
v2: Make the page table bitmap declared inside the function (Chris)
Simplify the way scratching address space works.
Move the alloc/teardown tracepoints up a level in the call stack so that
both all implementations get the trace.
v3: Updated trace event to spit out a name
v4: Aliasing ppgtt is now initialized differently (in setup global gtt)
v5: Rebase to latest code. Also removed unnecessary aliasing ppgtt check
for trace, as it is no longer possible after the PPGTT cleanup patch series
of a couple of months ago (Daniel).
v6: Implement changes from code review (Daniel):
- allocate/teardown_va_range calls added.
- Add a scratch page allocation helper (only need the address).
- Move trace events to a new patch.
- Use updated mark_tlbs_dirty.
- Moved pt preallocation for aliasing ppgtt into gen6_ppgtt_init.
v7: teardown_va_range removed (Daniel).
In init, gen6_ppgtt_clear_range call is only needed for aliasing ppgtt.
v8: Rebase after s/page_tables/page_table/.
v9: Remove unnecessary scratch flag in page_table struct, future patches
can just compare against ppgtt->scratch_pt, and alloc_pt_scratch becomes
redundant. Initialize scratch_pt and pt. (Mika)
v10: Clean up aliasing ppgtt init error path and prevent leaking the
ppgtt obj when init fails. (Mika)
Updated commit author. (Daniel)
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Michel Thierry <michel.thierry@intel.com> (v4+)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
We are already unmapping them in gen6_ppgtt_free. This function became
redundant since commit 06fda602dbca9c59d87db7da71192e4b54c9f5ff
("drm/i915: Create page table allocators").
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
i915_dma_map_single relies on dma_mapping_error, which returns positive
error codes. Found by static checker.
Introduced by commit 678d96fbb3b5995a2fdff2bca5e1ab4a40b7e968
("drm/i915: Track GEN6 page table usage").
v2: Return negative error code and renamed commit title. (Dan)
v3: Missing reported-by tag (Daniel)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Found by static analysis tool, this was harmless as the pt was not
used out of scope though.
Introduced by commit 678d96fbb3b5995a2fdff2bca5e1ab4a40b7e968
("drm/i915: Track GEN6 page table usage").
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Fix definition of the DRM_IOCTL_I915_GET_SPRITE_COLORKEY ioctl, so that it
is different from the DRM_IOCTL_I915_SET_SPRITE_COLORKEY ioctl.
Note that this is just for accuracy, the ioctl implementation itself is totally
unused and already ripped out.
Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
[danvet: Add note that this is a dead ioctl.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
It's completely unused and Tommi noticed that the #define is borked
since forever. I've done a git search in userspace and only found
broken definitions and no users anywhere.
Cc: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
The IMG PDC watchdog driver heartbeat module parameter has no default so
it is initialised to zero. This results in the following warning during
probe:
imgpdc-wdt 2006000.wdt: Initial timeout out of range! setting max timeout
The module parameter description implies that the default value should
be PDC_WDT_DEF_TIMEOUT, which isn't yet used, so initialise it to that.
Also tweak the heartbeat module parameter description for consistency.
Fixes: 93937669e9b5 ("watchdog: ImgTec PDC Watchdog Timer Driver")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: Naidu Tellapati <Naidu.Tellapati@imgtec.com>
Cc: Jude Abraham <Jude.Abraham@imgtec.com>
Cc: linux-watchdog@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
The IMG PDC watchdog probe function calls pdc_wdt_stop() prior to
watchdog_set_drvdata(), causing a NULL pointer dereference when
pdc_wdt_stop() retrieves the struct pdc_wdt_dev pointer using
watchdog_get_drvdata() and reads the register base address through it.
Fix by moving the watchdog_set_drvdata() call earlier, to where various
other pdc_wdt->wdt_dev fields are initialised.
Fixes: 93937669e9b5 ("watchdog: ImgTec PDC Watchdog Timer Driver")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: Naidu Tellapati <Naidu.Tellapati@imgtec.com>
Cc: Jude Abraham <Jude.Abraham@imgtec.com>
Cc: linux-watchdog@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
"ret" should be signed for the error handling to work correctly. This
doesn't matter much in real life since mtk_wdt_set_timeout() always
succeeds.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Move towards atomic by using the legacy modeset's drm_atomic_state
instead.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Move towards atomic by using the legacy modeset's drm_atomic_state
instead.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Instead of using connector->new_encoder, get the same information from
the pipe_config, thus making the function ready for the atomic
conversion.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
Stephane Viau
Hai Li
Rob Clark
Chris Ruffin
Emil Velikov
Ander Conselvan de Oliveira
Linus Torvalds
Dave Martin
Daniel Vetter
Ville Syrjälä
Chris Wilson
Joonas Lahtinen
kbuild test robot
Michel Thierry
Tommi Rantala
James Hogan
Dan Carpenter