| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In case the requested bus clock is higher than the input clock, the correct
dividers (pre = 0, post = 0) are returned from mx51_ecspi_clkdiv(), but
*fres is left uninitialized and therefore contains an arbitrary value.
This causes trouble for the recently introduced PIO polling feature as the
value in spi_imx->spi_bus_clk is used there to calculate for which
transfers to enable PIO polling.
Fix this by setting *fres even if no clock dividers are in use.
This issue was observed on Kontron BL i.MX8MM with an SPI peripheral clock set
to 50 MHz by default and a requested SPI bus clock of 80 MHz for the SPI NOR
flash.
With the fix applied the debug message from mx51_ecspi_clkdiv() now prints the
following:
spi_imx 30820000.spi: mx51_ecspi_clkdiv: fin: 50000000, fspi: 50000000,
post: 0, pre: 0
Fixes: 6fd8b8503a0d ("spi: spi-imx: Fix out-of-order CS/SCLK operation at low speeds")
Fixes: 07e759387788 ("spi: spi-imx: add PIO polling support")
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: David Jander <david@protonic.nl>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20221115181002.2068270-1-frieder@fris.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
A DEVAPC violation occurs when removing the module
due to accessing HW registers without base clock.
To fix this bug, the correct method is:
1. Call the runtime resume function to enable the
clock;
2. Operate the registers to reset the HW;
3. Turn off the clocks and disable the device
RPM mechanism.
Signed-off-by: Zhichao Liu <zhichao.liu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221110072839.30961-1-zhichao.liu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
According to data sheet SPI_SPD7 should be set to 7.
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221104100637.13376-1-vitalyr@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When this driver is used with a driver that uses preallocated spi_transfer
structs. The speed_hz is halved by every run. This results in:
spi_stm32 44004000.spi: SPI transfer setup failed
ads7846 spi0.0: SPI transfer failed: -22
Example when running with DIV_ROUND_UP():
- First run; speed_hz = 1000000, spi->clk_rate 125000000
div 125 -> mbrdiv = 7, cur_speed = 976562
- Second run; speed_hz = 976562
div 128,00007 (roundup to 129) -> mbrdiv = 8, cur_speed = 488281
- Third run; speed_hz = 488281
div 256,000131072067109 (roundup to 257) and then -EINVAL is returned.
Use DIV_ROUND_CLOSEST to allow to round down and allow us to keep the
set speed.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20221103080043.3033414-1-sean@geanix.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This fixes :
error: passing argument 1 of '__div64_32' from incompatible pointer type
By passing an uint64_t as first variable to do_div().
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 04694e50020b ("spi: meson-spicc: move wait completion in driver to take bursts delay in account")
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20221027-b4-spicc-burst-delay-fix-v2-0-8cc2bab3417a@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The flash and protected region mask is actually 0x7fff (30:16 and 14:0)
and not 0x3fff so fix this accordingly. While there use GENMASK() instead.
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20221025062800.22357-1-mika.westerberg@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit 7e963fb2a33ce ("spi: mediatek: add ipm design support
for MT7986") makes a mistake on package dividing operation
(one change is missing), need to fix it.
Background:
Ipm design is expanding the HW capability of dma (adjust package
length from 1KB to 64KB), and using "dev_comp->ipm_support" flag
to indicate it.
Issue description:
Ipm support patch (said above) is missing to handle remainder at
package dividing operation.
One case, a transmission length is 65KB, is will divide to 1K
(package length) * 65(package loop) in non-ipm desgin case, and
will divide to 64K(package length) * 1(package loop) + 1K(remainder)
in ipm design case. And the 1K remainder will be lost with the
current SW flow, and the transmission will be failure.
So, it should be fixed.
Solution:
Add "ipm_design" flag in function "mtk_spi_get_mult_delta()" to
indicate HW capability, and modify the parameters corespondingly.
fixes: 7e963fb2a33ce ("spi: mediatek: add ipm design support for MT7986")
Signed-off-by: zhichao.liu <zhichao.liu@mediatek.com>
Link: https://lore.kernel.org/r/20221021091653.18297-1-zhichao.liu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The following error messages are observed on boot for Tegra234 ...
ERR KERN tegra-qspi 3270000.spi: cannot use DMA: -19
ERR KERN tegra-qspi 3270000.spi: falling back to PIO
Tegra234 does not support DMA for the QSPI and so initialising the DMA
is expected to fail. The above error messages are misleading for devices
that don't support DMA and so fix this by skipping the DMA
initialisation for devices that don't support DMA.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20221026155633.141792-1-jonathanh@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add Jay Fang as the maintainer of the HiSilicon SFC Driver, replacing
John Garry.
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Acked-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/20221028023739.4113998-1-f.fangjian@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Some delay occurs between each bursts, thus the default delay is wrong
and a timeout will occur with big enough transfers.
The solution is to handle the timeout management in the driver and
add some delay for each bursts in the timeout calculation.
Reported-by: Da Xue <da@libre.computer>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20221026-spicc-burst-delay-v1-0-1be5ffb7051a@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The original fix "spi: stm32: Rate-limit the 'Communication suspended' message"
still leads to "stm32h7_spi_irq_thread: 1696 callbacks suppressed" spew in the
kernel log. Since this 'Communication suspended' message is a debug print, add
RATELIMIT_MSG_ON_RELEASE flag to inhibit the "callbacks suspended" part during
normal operation and only print summary at the end.
Fixes: ea8be08cc9358 ("spi: stm32: Rate-limit the 'Communication suspended' message")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20221018183513.206706-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The offset value of the mapping window in the kernel structure is
calculated using the value of the previous window offset. This doesn't
reflect how the HW is configured and can lead to erroneous setting of
the second flash device (CE1).
Cc: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Fixes: e3228ed92893 ("spi: spi-mem: Convert Aspeed SMC driver to spi-mem")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20221016155722.3520802-1-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Most of the device with QUP SPI adapter are actually using GPIO-s for
chip select.
However, this stopped working after ("spi: Retire legacy GPIO handling")
as it introduced a check on ->use_gpio_descriptors flag and since spi-qup
driver does not set the flag it meant that all of boards using GPIO-s and
with QUP adapter SPI devices stopped working.
So, to enable using GPIO-s again set ->use_gpio_descriptors to true and
populate ->max_native_cs.
Fixes: f48dc6b96649 ("spi: Retire legacy GPIO handling")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: luka.perkov@sartura.hr
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20221006194819.1536932-1-robert.marko@sartura.hr
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
According to documentation, the 64K erase opcode is located in VSCC
range [16:23] instead of [8:15].
Use the proper value to shift the mask over the correct range.
Signed-off-by: Mauro Lima <mauro.lima@eclypsium.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20221012152135.28353-1-mauro.lima@eclypsium.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Both quad SPI TX and RX modes can be supported on AST2600.
Correct typo in mode_bits field in both ast2600_fmc_data
and ast2600_spi_data structs.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20221005083209.222272-1-chin-ting_kuo@aspeedtech.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
NO_IRQ is used to check the return of irq_of_parse_and_map().
On some architecture NO_IRQ is 0, on other architectures it is -1.
irq_of_parse_and_map() returns 0 on error, independent of NO_IRQ.
So use 0 instead of using NO_IRQ.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/f41e09d710879726eacb98daedf16d0847303b9b.1665034444.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In this instance, "or" makes more sense than "of", so I guess that "or"
was intended and "of" was a typo.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Link: https://lore.kernel.org/r/20221008151459.1421406-1-j.neuschaefer@gmx.net
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use '-' instead of '=' in identifier: "GPL-2.0-or-later"
Signed-off-by: Tim Bird <tim.bird@sony.com>
Link: https://lore.kernel.org/r/BYAPR13MB2503FF6412666D29FEAC8DCDFD5B9@BYAPR13MB2503.namprd13.prod.outlook.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Return value should be updated to zero in combined sequence routine
if transfer is completed successfully. Currently it holds timeout value
resulting in errors.
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/20221001122148.9158-1-kyarlagadda@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
SPI code checks for non-zero sgt->orig_nents to determine if the buffer
has been DMA-mapped. Ensure that sg_table is really zeroed after free to
avoid potential NULL pointer dereference if the given SPI xfer object is
reused again without being DMA-mapped.
Fixes: 0c17ba73c08f ("spi: Fix cache corruption due to DMA/PIO overlap")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20220930113408.19720-1-m.szyprowski@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use the devm_platform_ioremap_resource() helper instead of calling
platform_get_resource() and devm_ioremap_resource() separately.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220928145256.1879256-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The COUNT_VALUE in the PACKET_CNT register is 16-bit so the maximum
value is 65535. Asking the driver to transfer a larger size currently
leads to the DMA transfer timing out. Implement ->max_transfer_size()
and have the core split the transfer as needed.
Fixes: 230d42d422e7 ("spi: Add s3c64xx SPI Controller driver")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20220927112117.77599-5-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
A couple of drivers call spi_split_transfers_maxsize() from their
->prepare_message() callbacks to split transfers which are too big for
them to handle. Add support in the core to do this based on
->max_transfer_size() to avoid code duplication.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20220927112117.77599-4-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The SPI core DMA mapping support performs cache management once for the
entire message and not between transfers, and this leads to cache
corruption if a message has two or more RX transfers with both
transfers targeting the same cache line, and the controller driver
decides to handle one using DMA and the other using PIO (for example,
because one is much larger than the other).
Fix it by syncing before/after the actual transfers. This also means
that we can skip the sync during the map/unmap of the message.
Fixes: 99adef310f68 ("spi: Provide core support for DMA mapping transfers")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20220927112117.77599-3-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Save the current RX and TX DMA devices to avoid having to duplicate the
logic to pick them, since we'll need access to them in some more
functions to fix a bug in the cache handling.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20220927112117.77599-2-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add spi dma max segment size declaration according to spi
hardware capability, instead of 64KB by system default
setting, to improve bus bandwidth for mass data transmission.
Signed-off-by: zhichao.liu <zhichao.liu@mediatek.com>
Link: https://lore.kernel.org/r/20220927083248.25404-1-zhichao.liu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
SoC MT7621 SPI bindings used text format, so migrate them to YAML.
There are some additions to the binding that were not in the original
file. This binding is used in MT7621 and MT7628a Ralink SoCs. To
properly match both dts nodes in tree we need to add to the schema
'clocks', 'clock-names' and 'reset-names'. Both 'clock-names' and
'reset-names' use 'spi' as string so maintain that as const in
the schema.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20220927031929.807070-1-sergio.paracuellos@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Document support for the Clock-Synchronized Serial Interface with FIFO
(MSIOF) in the Renesas R-Car V4H (R8A779G0) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/a840ca8487cfd612fae2b20c98e93ae7c7f50ef4.1664204638.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220924131854.964923-3-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use the devm_platform_get_and_ioremap_resource() helper instead of calling
platform_get_resource() and devm_ioremap_resource() separately.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220924131854.964923-2-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use the devm_platform_get_and_ioremap_resource() helper instead of calling
platform_get_resource() and devm_ioremap_resource() separately.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220924131854.964923-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context.
Fixes:db91841b58f9a ("spi/omap100k: Convert to runtime PM")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20220924121310.78331-4-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context.
Fixes:abf00907538e2 ("spi: dw: Add Baikal-T1 SPI Controller glue driver")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20220924121310.78331-3-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context.
Fixes:73d5fe0462702 ("spi: cadence-quadspi: Remove spi_master_put() in probe failure path")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20220924121310.78331-2-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Switch to use devm_spi_alloc_master() to simpify error path.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220920142216.3002291-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Switch to use devm_spi_alloc_master() to simpify error path.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/20220920114615.2681751-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Using the newest pm_runtime_resume_and_get is more appropriate
for simplifing code here.
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20220922150232.115843-1-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
devm_ioremap_resource() prints error message in itself. Remove the
dev_err call to avoid redundant error message.
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220923101632.19170-1-shangxiaojing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This switches the driver to use gpiod API instead of legacy gpio API,
which will brings us close to removing of_get_gpio() and other
OF-specific old APIs.
No functional change intended beyond some differences in error messages.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/Yy07WbMAG4bPgYNd@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
devm_ioremap_resource() prints error message in itself. Remove the
dev_err call to avoid redundant error message.
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Link: https://lore.kernel.org/r/20220923101726.19420-1-shangxiaojing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Switch to use devm_spi_alloc_master() to simpify error path.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Tested-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Link: https://lore.kernel.org/r/20220920114448.2681053-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The sparse tool complains as follows:
drivers/spi/spi-meson-spicc.c:570:22: warning:
symbol 'meson_spicc_pow2_clk_ops' was not declared. Should it be static?
This symbol is not used outside of spi-meson-spicc.c, so marks it static.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20220922040807.1409540-1-weiyongjun@huaweicloud.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This condition was accidentally changed from "if (status < 0)" to
"if (status)". The platform_get_irq() function returns non-zero
positive values on success so, unfortunately, the driver could not be
used. Change the condition back to how it was.
Fixes: f4ca8c88c2c7 ("spi: omap2-mcspi: Switch to use dev_err_probe() helper")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/Yyq8Q/kd301wVzg8@kili
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add a test where a small and a large transfer in a message hit the same
cache line. This test currently fails on spi-s3c64xx on in DMA mode
since it ends up mixing DMA and PIO without proper cache maintenance.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20220916113951.228398-2-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In the probe path, dev_err() can be replace with dev_err_probe()
which will check if error code is -EPROBE_DEFER and prints the
error name.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220917122504.1896302-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
As a preparation to unexport of_gpio_named_count(), convert the
driver to use gpiod_count() instead.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220914153333.37701-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Let the core handle all the chipselect bakery and replace
transfer_one_message() by transfer_one() and prepare_message().
At the time being, there is fsl_spi_cs_control() to handle
chipselects. That function handles both GPIO and non-GPIO
chipselects. The GPIO chipselects will now be handled by
the core directly, so only handle non-GPIO chipselects and
hook it to ->set_cs
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/753266abafe81722d86c3ddb8bac8ef1cb00fe8c.1660829841.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The Rockchip rk3399 TRM mentions that pd_sdioaudio includes
sdio, spi, i2s and spdif. Add a power-domains property to
to match reality with spi-rockchip.yaml.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/12af4fe6-4d35-cb4a-f5f6-06e3aba990cb@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add rockchip,rk3128-spi compatible string.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/c05fb9a3-ebf7-adec-e8ca-bd137d157f50@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The commit 5e0531f6b90a ("spi: Add capability to perform some transfer
with chipselect off") added a new flag but squeezed it into a wrong
group of struct spi_transfer members (note that SPI_NBITS_* are macros
for easier interpretation of the tx_nbits and rx_nbits bitfields).
Group cs_change and cs_off flags together and their doc strings.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220908130518.32186-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
Frieder Schrempf
Zhichao Liu
Vitaly Rodionov
Sean Nyekjaer
Neil Armstrong
Mika Westerberg
Jon Hunter
Jay Fang
Marek Vasut
Cédric Le Goater
Robert Marko
Mauro Lima
Chin-Ting Kuo
Christophe Leroy
Jonathan Neuschäfer
Bird, Tim
Krishna Yarlagadda
Marek Szyprowski
Yang Yingliang
Vincent Whitchurch
Sergio Paracuellos
Geert Uytterhoeven
Zhang Qilong
Shang XiaoJing
Dmitry Torokhov
Wei Yongjun
Dan Carpenter
Andy Shevchenko
Johan Jonker