| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add LEDs definition example for qca8k Switch Family to describe how they
should be defined for a correct usage.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Document support for LEDs node in ethernet-controller.
Ethernet Controller may support different LEDs that can be configured
for different operation like blinking on traffic event or port link.
Also add some Documentation to describe the difference of these nodes
compared to PHY LEDs, since ethernet-controller LEDs are controllable
by the ethernet controller regs and the possible intergated PHY doesn't
have control on them.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Marvell PHY can blink the LEDs, simple on/off. All LEDs blink at
the same rate, and the reset default is 84ms per blink, which is
around 12Hz.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Linux LEDs can be requested to perform hardware accelerated
blinking. Pass this to the PHY driver, if it implements the op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a brightness function, so the LEDs can be controlled from
software using the standard Linux LED infrastructure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Linux LEDs can be software controlled via the brightness file in /sys.
LED drivers need to implement a brightness_set function which the core
will call. Implement an intermediary in phy_device, which will call
into the phy driver if it implements the necessary function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Define common binding parsing for all PHY drivers with LEDs using
phylib. Parse the DT as part of the phy_probe and add LEDs to the
linux LED class infrastructure. For the moment, provide a dummy
brightness function, which will later be replaced with a call into the
PHY driver. This allows testing since the LED core might otherwise
reject an LED whose brightness cannot be set.
Add a dependency on LED_CLASS. It either needs to be built in, or not
enabled, since a modular build can result in linker errors.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Provide stubs for devm_led_classdev_register_ext() and
led_init_default_state_get() so that LED drivers embedded within other
drivers such as PHYs and Ethernet switches still build when LEDS_CLASS
or NEW_LEDS are disabled. This also helps with Kconfig dependencies,
which are somewhat hairy for phylib and mdio and only get worse when
adding a dependency on LED_CLASS.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add LEDs blink_set() support to qca8k Switch Family.
These LEDs support hw accellerated blinking at a fixed rate
of 4Hz.
Reject any other value since not supported by the LEDs switch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add LEDs basic support for qca8k Switch Family by adding basic
brightness_set() support.
Since these LEDs refelect port status, the default label is set to
":port". DT binding should describe the color and function of the
LEDs using standard LEDs api.
Each LED always have the device name as prefix. The device name is
composed from the mii bus id and the PHY addr resulting in example
names like:
- qca8k-0.0:00:amber:lan
- qca8k-0.0:00:white:lan
- qca8k-0.0:01:amber:lan
- qca8k-0.0:01:white:lan
These LEDs supports only blocking variant of the brightness_set()
function since they can sleep during access of the switch leds to set
the brightness.
While at it add to the qca8k header file each mode defined by the Switch
Documentation for future use.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move qca8k_port_to_phy() to qca8k header as it's useful for future
reference in Switch LEDs module since the same logic is applied to get
the right index of the switch port.
Make it inline as it's simple function that just decrease the port.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Our use-case needs two AT ports available:
One for running a ppp daemon, and another one for management
This patch enables a second AT port on DATA1
Signed-off-by: Jaime Breva <jbreva@nayarsystems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Here we add support for multi-buffer XDP handling in Striding RQ, which
is our default out-of-the-box RQ type. Before this series, loading such
an XDP program would fail, until you switch to the legacy RQ (by
unsetting the rx_striding_rq priv-flag).
To overcome the lack of headroom and tailroom between the strides, we
allocate a side page to be used for the descriptor (xdp_buff / skb) and
the linear part. When an XDP program is attached, we structure the
xdp_buff so that it contains no data in the linear part, and the whole
packet resides in the fragments.
In case of XDP_PASS, where an SKB still needs to be created, we copy up
to 256 bytes to its linear part, to match the current behavior, and
satisfy functions that assume finding the packet headers in the SKB
linear part (like eth_type_trans).
Performance testing:
Packet rate test, 64 bytes, 32 channels, MTU 9000 bytes.
CPU: Intel(R) Xeon(R) Platinum 8380 CPU @ 2.30GHz.
NIC: ConnectX-6 Dx, at 100 Gbps.
+----------+-------------+-------------+---------+
| Test | Legacy RQ | Striding RQ | Speedup |
+----------+-------------+-------------+---------+
| XDP_DROP | 101,615,544 | 117,191,020 | +15% |
+----------+-------------+-------------+---------+
| XDP_TX | 95,608,169 | 117,043,422 | +22% |
+----------+-------------+-------------+---------+
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for supporting XDP multi-buffer in striding RQ, use
xdp_buff struct to describe the packet. Make its skb_shared_info collide
the one of the allocated SKB, then add the fragments using the xdp_buff
API.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make the function more generic. Let it get an additional frame_sz
parameter instead of deriving it from the RQ struct.
No functional change here, just a preparation for a downstream patch.
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce mlx5e_add_skb_shared_info_frag(), a function dedicated for
adding a fragment into a struct skb_shared_info object.
Use it in the Legacy RQ flow. Similar usage will be added in a
downstream patch by the corresponding Striding RQ flow.
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Under a few restrictions, TX MPWQE feature can serve multiple TX packets
in a single TX descriptor. It requires each of the packets to have a
single scatter entry / segment.
Today we allow only linear frames to use this feature, although there's
no real problem with non-linear ones where the whole packet reside in
the first fragment.
Expand the XDP TX MPWQE feature support to include such frames. This is
in preparation for the downstream patch, in which we will generate such
non-linear frames.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the assumption of non-zero linear length in the XDP xmit
function, used to serve both internal XDP_TX operations as well as
redirected-in requests.
Do not apply the MLX5E_XDP_MIN_INLINE check unless necessary.
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Function mlx5e_rx_get_linear_stride_sz() returns PAGE_SIZE immediately
in case an XDP program is attached. The more accurate formula is
ALIGN(sz, PAGE_SIZE), to prevent two packets from residing on the same
page.
The assumption behind the current code is that sz <= PAGE_SIZE holds for
all cases with XDP program set.
This is true because it is being called from:
- 3 times from Striding RQ flows, in which XDP is not supported for such
large packets.
- 1 time from Legacy RQ flow, under the condition
mlx5e_rx_is_linear_skb().
No functional change here, just removing the implied assumption in
preparation for supporting XDP multi-buffer in Striding RQ.
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change mlx5e_xdp_allowed() so it gets the params structure with the
xdp_prog applied, rather than creating a local copy based on the current
params in priv.
This reduces the amount of memory on the stack, and acts on the exact
params instance that's about to be applied.
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Non-linear mem scheme of Striding RQ does not yet support XDP at this
point. Take the check where it belongs, inside the params validation
function mlx5e_params_validate_xdp().
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Handle multi-buffer XDP redirect-in requests coming through
mlx5e_xdp_xmit.
Extend struct mlx5e_xmit_data_frags with an additional dma_arr field, to
point to the fragments dma mapping, as they cannot be retrieved via the
page_pool_get_dma_addr() function.
Push a dma_addr xdpi instance per each fragment, and use them in the
completion flow to dma_unmap the frags.
Finally, remove the restriction in mlx5e_open_xdpsq, and set the flag in
xdp_features.
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Here we fix the current wi->num_pkts abuse, as it was used to indicate
multiple xdpi entries in the xdpi_fifo.
Instead, reduce mlx5e_xdp_info to the size of a single field, making it
a union of unions. Per packet, use as many instances as needed to
provide the information needed at the time of completion.
The sequence of xdpi instances pushed is well defined, derived by the
xmit_mode.
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is not likely nor unlikely that the xdp buff has fragments, it
depends on the program loaded and size of the packet received.
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce struct mlx5e_xmit_data_frags to be used for non-linear xmit
buffers. Let it include sinfo pointer.
Take one bit from the len field to indicate if the descriptor has
fragments and can be casted-up into the extended version.
Zero-init to make sure has_frags, and potentially future fields, are
zero when not explicitly assigned.
Another field will be added in a downstream patch to indicate and point
to dma addresses of the different frags, for redirect-in requests.
This simplifies the mlx5e_xmit_xdp_frame/mlx5e_xmit_xdp_frame_mpwqe
functions params.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move TX datapath struct from the generic en.h to the datapath txrx.h
header, where it belongs.
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move struct mlx5e_xdp_info and enum mlx5e_xdp_xmit_mode from the generic
en.h to the XDP header, where they belong.
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove no more supported platforms (stih415/stih416 and stid127)
Signed-off-by: Alain Volmat <avolmat@me.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20230416195523.61075-1-avolmat@me.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The types for the register argument changed recently, but there are
still incompatible prototypes that got left behind, and gcc-13 warns
about these:
In file included from drivers/net/ethernet/mscc/ocelot.c:13:
drivers/net/ethernet/mscc/ocelot.h:97:5: error: conflicting types for 'ocelot_port_readl' due to enum/integer mismatch; have 'u32(struct ocelot_port *, u32)' {aka 'unsigned int(struct ocelot_port *, unsigned int)'} [-Werror=enum-int-mismatch]
97 | u32 ocelot_port_readl(struct ocelot_port *port, u32 reg);
| ^~~~~~~~~~~~~~~~~
Just remove the two prototypes, and rely on the copy in the global
header.
Fixes: 9ecd05794b8d ("net: mscc: ocelot: strengthen type of "u32 reg" in I/O accessors")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20230417205531.1880657-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
stmmac_dev_probe doesn't propagate feature flags to VLANs. So features
like offloading don't correspond with the general features and it's not
possible to manipulate features via ethtool -K to affect VLANs.
Propagate feature flags to vlan features. Drop TSO feature because
it does not work on VLANs yet.
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Link: https://lore.kernel.org/r/20230417192845.590034-1-vinschen@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, bonding only obtain the timestamp (ts) information of
the active slave, which is available only for modes 1, 5, and 6.
For other modes, bonding only has software rx timestamping support.
However, some users who use modes such as LACP also want tx timestamp
support. To address this issue, let's check the ts information of each
slave. If all slaves support tx timestamping, we can enable tx
timestamping support for the bond.
Add a note that the get_ts_info may be called with RCU, or rtnl or
reference on the device in ethtool.h>
Suggested-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20230418034841.2566262-1-liuhangbin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
dwmac supports multiple modess. When working under rmii and rgmii,
you need to set different phy interfaces.
According to the dwmac document, when working in rmii, it needs to be
set to 0x4, and rgmii needs to be set to 0x1.
The phy interface needs to be set in syscon, the format is as follows:
starfive,syscon: <&syscon, offset, shift>
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This adds StarFive dwmac driver support on the StarFive JH7110 SoC.
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Co-developed-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add documentation to describe StarFive dwmac driver(GMAC).
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
According to:
stmmac_platform.c: stmmac_probe_config_dt
stmmac_main.c: stmmac_dvr_probe
dwmac controller may require one (stmmaceth) or two (stmmaceth+ahb)
reset signals, and the maxItems of resets/reset-names is going to be 2.
The gmac of Starfive Jh7110 SOC must have two resets.
it uses snps,dwmac-5.20 IP.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add "snps,dwmac-5.20" compatible string for 5.20 version that can avoid
to define some platform data in the glue layer.
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add dwmac-5.20 IP version to snps.dwmac.yaml
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Use new net core macro netif_subqueue_completed_wake to simplify
the code of the tx cleanup path.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Use new net core macro netif_subqueue_maybe_stop in the start_xmit path
to simplify the code. Whilst at it, set the tx queue start threshold to
twice the stop threshold. Before values were the same, resulting in
stopping/starting the queue more often than needed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add netif_subqueue_completed_wake, complementing the subqueue versions
netif_subqueue_try_stop and netif_subqueue_maybe_stop.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In order to not transmit (preemptible) frames which will be received by
the link partner as corrupted (because it doesn't support FP), the
hardware requires the driver to program the QSYS_PREEMPTION_CFG_P_QUEUES
register only after the MAC Merge layer becomes active (verification
succeeds, or was disabled).
There are some cases when FP is known (through experimentation) to be
broken. Give priority to FP over cut-through switching, and disable FP
for known broken link modes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The mqprio queue configuration can appear either through
TC_SETUP_QDISC_MQPRIO or through TC_SETUP_QDISC_TAPRIO. Make sure both
are treated in the same way.
Code does nothing new for now (except for rejecting multiple TXQs per
TC, which is a useless concept with DSA switches).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ferenc Fejes <fejes@inf.elte.hu>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This doesn't apply anything to hardware and in general doesn't do
anything that the software variant doesn't do, except for checking that
there isn't more than 1 TXQ per TC (TXQs for a DSA switch are a dubious
concept anyway). The reason we add this is to be able to parse one more
field added to struct tc_mqprio_qopt_offload, namely preemptible_tcs.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ferenc Fejes <fejes@inf.elte.hu>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ocelot_mm_update_port_status() updates mm->verify_status, but when the
verification state of a port changes, an IRQ isn't emitted, but rather,
only when the verification state reaches one of the final states (like
DISABLED, FAILED, SUCCEEDED) - things that would affect mm->tx_active,
which is what the IRQ *is* actually emitted for.
That is to say, user space may miss reports of an intermediary MAC Merge
verification state (like from INITIAL to VERIFYING), unless there was an
IRQ notifying the driver of the change in mm->tx_active as well.
This is not a huge deal, but for reliable reporting to user space, let's
call ocelot_mm_update_port_status() synchronously from
ocelot_port_get_mm(), which makes user space see the current MM status.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The MAC Merge IRQ of all ports is shared with the PTP TX timestamp IRQ
of all ports, which means that currently, when a PTP TX timestamp is
generated, felix_irq_handler() also polls for the MAC Merge layer status
of all ports, looking for changes. This makes the kernel do more work,
and under certain circumstances may make ptp4l require a
tx_timestamp_timeout argument higher than before.
Changes to the MAC Merge layer status are only to be expected under
certain conditions - its TX direction needs to be enabled - so we can
check early if that is the case, and omit register access otherwise.
Make ocelot_mm_update_port_status() skip register access if
mm->tx_enabled is unset, and also call it once more, outside IRQ
context, from ocelot_port_set_mm(), when mm->tx_enabled transitions from
true to false, because an IRQ is also expected in that case.
Also, a port may have its MAC Merge layer enabled but it may not have
generated the interrupt. In that case, there's no point in writing to
DEV_MM_STATUS to acknowledge that IRQ. We can reduce the number of
register writes per port with MM enabled by keeping an "ack" variable
which writes the "write-one-to-clear" bits. Those are 3 in number:
PRMPT_ACTIVE_STICKY, UNEXP_RX_PFRM_STICKY and UNEXP_TX_PFRM_STICKY.
The other fields in DEV_MM_STATUS are read-only and it doesn't matter
what is written to them, so writing zero is just fine.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Unfortunately, the workarounds for the hardware bugs make it pointless
to keep fine-grained locking for the MAC Merge state of each port.
Our vsc9959_cut_through_fwd() implementation requires
ocelot->fwd_domain_lock to be held, in order to serialize with changes
to the bridging domains and to port speed changes (which affect which
ports can be cut-through). Simultaneously, the traffic classes which can
be cut-through cannot be preemptible at the same time, and this will
depend on the MAC Merge layer state (which changes from threaded
interrupt context).
Since vsc9959_cut_through_fwd() would have to hold the mm->lock of all
ports for a correct and race-free implementation with respect to
ocelot_mm_irq(), in practice it means that any time a port's mm->lock is
held, it would potentially block holders of ocelot->fwd_domain_lock.
In the interest of simple locking rules, make all MAC Merge layer state
changes (and preemptible traffic class changes) be serialized by the
ocelot->fwd_domain_lock.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the switch emits an IRQ, we don't know what caused it, and we
iterate through all ports to check the MAC Merge status.
Move that iteration inside the ocelot lib; we will change the locking in
a future change and it would be good to encapsulate that lock completely
within the ocelot lib.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add receive hardware timestamp metadata support via kfunc to XDP Zero Copy
receive packets.
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add receive hardware timestamp metadata support via kfunc to XDP receive
packets.
Suggested-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Acked-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Introduce struct stmmac_xdp_buff as a preparation to support XDP Rx
metadata via kfuncs.
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
Christian Marangi
Andrew Lunn
Jaime Breva
Tariq Toukan
Alain Volmat
Arnd Bergmann
Corinna Vinschen
Hangbin Liu
Samin Guo
Yanhong Wang
Emil Renner Berthing
Heiner Kallweit
Vladimir Oltean
Song Yoong Siang