| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Commit 5f84bb1a4099 ("soc/tegra: pmc: Add sysfs entries for reset info")
added support for reading the Tegra reset source and level from sysfs.
However, there are a few issues with this commit which are ...
1. The number of reset sources for Tegra210 is defined as 5 but it
should be 6.
2. The number of reset sources for Tegra186 is defined as 13 but it
should be 15.
3. The SoC data variables num_reset_sources and num_reset_levels are
defined but never used.
Fix the above by ...
1. Removing the reset source 'AOTAG' from the tegra30_reset_sources
because this is only applicable for Tegra210.
2. Adding a new tegra210_reset_sources structure for Tegra210 reset
sources.
3. Correct the number of reset sources for Tegra210 and Tegra186 by
using the ARRAY_SIZE macro.
4. Updating the functions reset_reason_show() and reset_level_show()
to check whether the value read is valid. While we are at it
clean-up these functions to remove an unnecessary u32 variable.
Fixes: 5f84bb1a4099 ("soc/tegra: pmc: Add sysfs entries for reset info")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
By implementing the acquire/release protocol, the resets can be shared
with other drivers that also adhere to this protocol. This will be used
for example by the SOR driver to put hardware into a known good state,
irrespective of whether or not the power domain can be reset.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add implementations that apply acquire and release operations to all
reset controls part of a reset control array.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
In order to be able to request an array of reset controls in acquired or
released mode, add the acquired flag to of_reset_control_array_get() and
pass the flag to subsequent calls of __of_reset_control_get().
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
There are cases where a driver needs explicit control over a reset line
that is exclusively conneted to its device, but this control has to be
temporarily handed over to the power domain controller to handle reset
requirements during power transitions.
Allow multiple exclusive reset controls to be requested in 'released'
state for the same physical reset line, only one of which can be
acquired at the same time.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
|
|
Fixes: 400816f60c54 ("perf/x86/intel: Implement support for TSX Force Abort")
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "Peter Zijlstra (Intel)" <peterz@infradead.org>
Cc: kbuild-all@01.org
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20190313184243.GA10820@lkp-sb-ep06
|
|
When this .gitignore was added, lxdialog was an independent hostprogs-y.
Now that all objects in lxdialog/ are directly linked to mconf, the
lxdialog is no longer generated.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Currently, every arch/*/include/uapi/asm/Kbuild explicitly includes
the common Kbuild.asm file. Factor out the duplicated include directives
to scripts/Makefile.asm-generic so that no architecture would opt out
of the mandatory-y mechanism.
um is not forced to include mandatory-y since it is a very exceptional
case which does not support UAPI.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The generic-y is redundant under the following condition:
- arch has its own implementation
- the same header is added to generated-y
- the same header is added to mandatory-y
If a redundant generic-y is found, the warning like follows is displayed:
scripts/Makefile.asm-generic:20: redundant generic-y found in arch/arm/include/asm/Kbuild: timex.h
I fixed up arch Kbuild files found by this.
Suggested-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This reverts commit caf6fe91ddf62a96401e21e9b7a07227440f4185.
The commit was fine but is no longer needed as of commit 3a2429e1faf4
("kbuild: change if_changed_rule for multi-line recipe"). Let's go
back to using ";" to be consistent.
For some discussion, see:
https://lkml.kernel.org/r/CAK7LNASde0Q9S5GKeQiWhArfER4S4wL1=R_FW8q0++_X3T5=hQ@mail.gmail.com
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
During a simple no-op (nothing changed) build I saw 39 invocations of
the C compiler with the argument "-print-file-name=include". We don't
need to call the C compiler 39 times for this--one time will suffice.
Let's change NOSTDINC_FLAGS to a simply expanded variable to avoid
this since there doesn't appear to be any reason it should be
recursively expanded.
On my build this shaved ~400 ms off my "no-op" build.
Note that the recursive expansion seems to date back to the (really
old) commit e8f5bdb02ce0 ("[PATCH] Makefile include path ordering").
It's a little unclear to me if the point of that patch was to switch
the variable to be recursively expanded (which it did) or to avoid
directly assigning to NOSTDINC_FLAGS (AKA to switch to +=) because
someone else (out of tree?) was setting it. I presume later since if
the only goal was to switch to recursive expansion the patch would
have just removed the ":".
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
* The man page for dpkg-source(1) notes:
> -b, --build directory [format-specific-parameters]
> Build a source package (--build since dpkg 1.17.14).
> <...>
>
> dpkg-source will build the source package with the first
> format found in this ordered list: the format indicated
> with the --format command line option, the format
> indicated in debian/source/format, “1.0”. The fallback
> to “1.0” is deprecated and will be removed at some point
> in the future, you should always document the desired
> source format in debian/source/format. See section
> SOURCE PACKAGE FORMATS for an extensive description of
> the various source package formats.
Thus it would be more foolproof to explicitly use 1.0 (as we always
did) than to rely on dpkg-source's defaults.
* In a similar vein, debian/rules is not made executable by mkdebian,
and dpkg-source warns about that but still silently fixes the file.
Let's be explicit once again.
Signed-off-by: Arseny Maslennikov <ar@cs.msu.ru>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
Jon Hunter
Thierry Reding
Philipp Zabel
Linus Torvalds
kbuild test robot
Masahiro Yamada
Douglas Anderson
Arseny Maslennikov