| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Kmemleak shows the following leak arising from routine in the usb
probe routine:
unreferenced object 0xffff895cb29bba00 (size 512):
comm "(udev-worker)", pid 534, jiffies 4294903932 (age 102751.088s)
hex dump (first 32 bytes):
77 30 30 30 00 00 00 00 02 2f 2d 2b 30 00 00 00 w000...../-+0...
02 00 2a 28 00 00 00 00 ff 55 ff ff ff 00 00 00 ..*(.....U......
backtrace:
[<ffffffff9265fa36>] kmalloc_trace+0x26/0x90
[<ffffffffc17eec41>] rtw_usb_probe+0x2f1/0x680 [rtw_usb]
[<ffffffffc03e19fd>] usb_probe_interface+0xdd/0x2e0 [usbcore]
[<ffffffff92b4f2fe>] really_probe+0x18e/0x3d0
[<ffffffff92b4f5b8>] __driver_probe_device+0x78/0x160
[<ffffffff92b4f6bf>] driver_probe_device+0x1f/0x90
[<ffffffff92b4f8df>] __driver_attach+0xbf/0x1b0
[<ffffffff92b4d350>] bus_for_each_dev+0x70/0xc0
[<ffffffff92b4e51e>] bus_add_driver+0x10e/0x210
[<ffffffff92b50935>] driver_register+0x55/0xf0
[<ffffffffc03e0708>] usb_register_driver+0x88/0x140 [usbcore]
[<ffffffff92401153>] do_one_initcall+0x43/0x210
[<ffffffff9254f42a>] do_init_module+0x4a/0x200
[<ffffffff92551d1c>] __do_sys_finit_module+0xac/0x120
[<ffffffff92ee6626>] do_syscall_64+0x56/0x80
[<ffffffff9300006a>] entry_SYSCALL_64_after_hwframe+0x46/0xb0
The leak was verified to be real by unloading the driver, which resulted
in a dangling pointer to the allocation.
The allocated memory is freed in rtw_usb_intf_deinit().
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230417160331.23071-1-Larry.Finger@lwfinger.net
|
|
We have to call rtw8821c_switch_rf_set() with SWITCH_TO_WLG or
SWITCH_TO_BTG according to the chip variant as denoted in rfe_option.
The information which argument to use for which variant has been
taken from the vendor driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230417140358.2240429-5-s.hauer@pengutronix.de
|
|
According to the vendor driver the pkg_type has to be set to '1'
for some rtw8821c variants. As the pkg_type has been hardcoded to
'0', add a field for it in struct rtw_hal and set this correctly
in the rtw8821c part.
With this parsing of a rtw_table is influenced and check_positive()
in phy.c returns true for some cases here. The same is done in the
vendor driver. However, this has no visible effect on the driver
here.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230417140358.2240429-4-s.hauer@pengutronix.de
|
|
On my RTW8821CU chipset rfe_option reads as 0x22. Looking at the
vendor driver suggests that the field width of rfe_option is 5 bit,
so rfe_option should be masked with 0x1f.
Without this the rfe_option comparisons with 2 further down the
driver evaluate as false when they should really evaluate as true.
The effect is that 2G channels do not work.
rfe_option is also used as an array index into rtw8821c_rfe_defs[].
rtw8821c_rfe_defs[34] (0x22) was added as part of adding USB support,
likely because rfe_option reads as 0x22. As this now becomes 0x2,
rtw8821c_rfe_defs[34] is no longer used and can be removed.
Note that this might not be the whole truth. In the vendor driver
there are indeed places where the unmasked rfe_option value is used.
However, the driver has several places where rfe_option is tested
with the pattern if (rfe_option == 2 || rfe_option == 0x22) or
if (rfe_option == 4 || rfe_option == 0x24), so that rfe_option BIT(5)
has no influence on the code path taken. We therefore mask BIT(5)
out from rfe_option entirely until this assumption is proved wrong
by some chip variant we do not know yet.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Alexandru gagniuc <mr.nuke.me@gmail.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: ValdikSS <iam@valdikss.org.ru>
Cc: stable@vger.kernel.org
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230417140358.2240429-3-s.hauer@pengutronix.de
|
|
The RTW88 chipsets have four different priority queues in hardware. For
the USB type chipsets the packets destined for a specific priority queue
must be sent through the endpoint corresponding to the queue. This was
not fully understood when porting from the RTW88 USB out of tree driver
and thus violated.
This patch implements the qsel to endpoint mapping as in
get_usb_bulkout_id_88xx() in the downstream driver.
Without this the driver often issues "timed out to flush queue 3"
warnings and often TX stalls completely.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: ValdikSS <iam@valdikss.org.ru>
Tested-by: Alexandru gagniuc <mr.nuke.me@gmail.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable@vger.kernel.org
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230417140358.2240429-2-s.hauer@pengutronix.de
|
|
Allow 8822c to operate two interface concurrently, only 1 AP mode plus
1 station mode under same frequency is supported. Combination of other
types will not be added until requested.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230414121331.18062-1-pkshih@realtek.com
|
|
This patch allows vifs sharing same hardware with the AP mode vif to
do scan, do note that this could lead to packet loss or disconnection
of the AP's clients. Since we don't have chanctx, update scan info
upon set channel so bandwidth changes won't go unnoticed and get
misconfigured after scan. Download beacon just before scan starts to
allow hardware to get proper content to do beaconing. Last, beacons
should only be transmitted in AP's operating channel. Turn related
beacon functions off while we're in other channels so the receiving
stations won't get confused.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230414121323.18008-1-pkshih@realtek.com
|
|
Only abort scan with current scanning VIF. If we have more than one
interface, we could call rtw_hw_scan_abort() with the wrong VIF as
input. This avoids potential null pointer being accessed when actually
the other VIF is scanning.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230414121312.17954-1-pkshih@realtek.com
|
|
Only gather reserved pages from AP interface after it has started. Or
else ieee80211_beacon_get_*() returns NULL and causes other VIFs'
reserved pages fail to download. Update location of current reserved page
after beacon renews so offsets changed by beacon can be recognized.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230414121300.17900-1-pkshih@realtek.com
|
|
Firmware can't support PS mode during AP mode, so disallow this case.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230414121135.17828-5-pkshih@realtek.com
|
|
Extend 8822c's reserved page number to accommodate additional required
pages. Reserved page is an area of memory in the FIFO dedicated for
special purposes. Previously only one interface is supported so 8 pages
should suffice, extend it so we can support 2 interfaces concurrently.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230414121135.17828-4-pkshih@realtek.com
|
|
Switch port settings if AP mode does not start on port 0 because of
hardware limitation. For some ICs, beacons on ports other than zero
could misbehave and do not issue properly, to fix this we change AP
VIFs to port zero when multiple interfaces is active.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230414121135.17828-3-pkshih@realtek.com
|
|
In order to support multiple interfaces, multiple port settings will
be required. Current code always uses port 0 and should be changed.
Declare a bitmap with size equal to hardware port number to record
the current usage.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230414121135.17828-2-pkshih@realtek.com
|
|
The function to request DLE (data link engine) buffer uses 'u16' as return
value that mixes error code, so change it to 'int' as regular error code.
Also, treat invalid register value (0xfff) as an error.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230414082228.30766-1-pkshih@realtek.com
|
|
Smatch complains that:
debugfs_hw_add() warn: 'statsd' is an error pointer or valid
Debugfs checks are generally not supposed to be checked for errors
and it is not necessary here.
Just delete the dead code.
Signed-off-by: Yingsha Xu <ysxu@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/r/20230419104548.30124-1-ysxu@hust.edu.cn
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When CSME takes ownership, the driver sets RFKILL on, and this
triggers driver unload and sending the confirmation SAP message.
However, when IWL_MVM_MEI_REPORT_RFKILL is set, RFKILL was not
reported and as a result, the driver did not confirm the ownership
transition. Fix it.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230418122405.29ac3cd3df73.I96b32bc274bfe1e3871e54d3fa29c7ac4f40446f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When the host disconnects from the AP CSME takes ownership right away.
Since the driver never asks for ownership again wifi is left in rfkill
until CSME releases the NIC, although in many cases the host could
re-connect shortly after the disconnection. To allow the host to
recover from occasional disconnection, re-ask for ownership to let
the host connect again.
Allow one minute before re-asking for ownership to avoid too frequent
ownership transitions.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230418122405.a6c6ebc48f2d.I8a17003b86e71b3567521cc69864b9cbe9553ea9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When mei filtered scan is performed, it must find the AP on the first
scan, otherwise CSME will take the ownership of the NIC.
Make this scan more aggressive by scanning the channel the AP is
supposed to be on (as reported by CSME) several times.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230418122405.47e383b10b18.I14340a118acdb19ecb7214e7ff413054c77bd99c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When CSME is connected and has link protection set, the driver must
connect to the same AP CSME is connected to.
When in link protection, modify scan request parameters to include
only the channel of the AP CSME is connected to and scan for the
same SSID. In addition, filter the scan results to include only
results from the same AP. This will make sure the driver will connect
to the same AP and will do it fast enough to keep the session alive.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230418122405.c1b55de3d704.I3895eebe18b3b672607695c887d728e113fc85ec@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Enable driver's support for MLO APIs to unlock this functionality.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20230418122405.0ae0dd6f0481.Iec993cf0f28eacb2483fb9d1e755b0b2fd62e163@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
For constant values we don't need rcu_assign_pointer(),
use RCU_INIT_POINTER() instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230418122405.7b400d21a27f.Iccdef9d777677390a9881c88b06c0ed13a83d978@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If we do get multiple notifications from firmware, then
we might have allocated 'notif', but don't free it. Fix
that by checking for duplicates before allocation.
Fixes: 4da46a06d443 ("wifi: iwlwifi: mvm: Add support for wowlan info notification")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230418122405.116758321cc4.I8bdbcbb38c89ac637eaa20dda58fa9165b25893a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We should pass the newly allocated data to fill.
Signed-off-by: Alon Giladi <alon.giladi@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230418122405.aaa6d8874442.I734841c71aad9564cb22c50f2737aaff489fadaf@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The RADA/firmware collaborate on MIC stripping in the following
way:
- the firmware fills the IWL_RX_MPDU_MFLG1_MIC_CRC_LEN_MASK
value for how many words need to be removed at the end of
the frame, CRC and, if decryption was done, MIC
- if the RADA is active, it will
- remove that much from the end of the frame
- zero the value in IWL_RX_MPDU_MFLG1_MIC_CRC_LEN_MASK
As a consequence, the only thing the driver should need to do
is to
- unconditionally tell mac80211 that the MIC was removed
if decryption was already done
- remove as much as IWL_RX_MPDU_MFLG1_MIC_CRC_LEN_MASK says
at the end of the frame, since either RADA did it and then
the value is 0, or RADA was disabled and then the value is
whatever should be removed to strip both CRC & MIC
However, all this code was historically grown and getting a
bit confused. Originally, we were indicating that the MIC was
not stripped, which is the version of the code upstreamed in
commit 780e87c29e77 ("iwlwifi: mvm: add 9000 series RX processing")
which indicated RX_FLAG_DECRYPTED in iwl_mvm_rx_crypto().
We later had a commit to change that to also indicate that the
MIC was stripped, adding RX_FLAG_MIC_STRIPPED. However, this was
then "fixed" later to only do that conditionally on RADA being
enabled, since otherwise RADA didn't strip the MIC bytes yet.
At the time, we were also always including the FCS if the RADA
was not enabled, so that was still broken wrt. the FCS if the
RADA isn't enabled - but that's a pretty rare case. Notably
though, it does happen for management frames, where we do need
to remove the MIC and CRC but the RADA is disabled.
Later, in commit 40a0b38d7a7f ("iwlwifi: mvm: Fix calculation of
frame length"), we changed this again, upstream this was just a
single commit, but internally it was split into first the correct
commit and then an additional fix that reduced the number of bytes
that are removed by crypt_len. Note that this is clearly wrong
since crypt_len indicates the length of the PN header (always 8),
not the length of the MIC (8 or 16 depending on algorithm).
However, this additional fix mostly canceled the other bugs,
apart from the confusion about the size of the MIC.
To fix this correctly, remove all those additional workarounds.
We really should always indicate to mac80211 the MIC was stripped
(it cannot use it anyway if decryption was already done), and also
always actually remove it and the CRC regardless of the RADA being
enabled or not. That's simple though, the value indicated in the
metadata is zeroed by the RADA if it's enabled and used the value,
so there's no need to check if it's enabled or not.
Notably then, this fixes the MIC size confusion, letting us receive
GCMP-256 encrypted management frames correctly that would otherwise
be reported to mac80211 8 bytes too short since the RADA is turned
off for them, crypt_len is 8, but the MIC size is 16, so when we do
the adjustment based on IWL_RX_MPDU_MFLG1_MIC_CRC_LEN_MASK (which
indicates 20 bytes to remove) we remove 12 bytes but indicate then
to mac80211 the MIC is still present, so mac80211 again removes the
MIC of 16 bytes, for an overall removal of 28 rather than 20 bytes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230418122405.81345b6ab0cd.Ibe0348defb6cce11c99929a1f049e60b5cfc150c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Fix a memory leak that occurs when reading the fw_info
file all the way, since we return NULL indicating no
more data, but don't free the status tracking object.
Fixes: 36dfe9ac6e8b ("iwlwifi: dump api version in yaml format")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230418122405.239e501b3b8d.I4268f87809ef91209cbcd748eee0863195e70fa2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add support for B0 version of MAC of MR device
Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230418122405.5dca1ea7a0cf.I87932e1e216a1940eeae8824071ecb777f4c034f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
A received TKIP key may be up to 32 bytes because it may contain
MIC rx/tx keys too. These are not used by iwl and copying these
over overflows the iwl_keyinfo.key field.
Add a check to not copy more data to iwl_keyinfo.key then will fit.
This fixes backtraces like this one:
memcpy: detected field-spanning write (size 32) of single field "sta_cmd.key.key" at drivers/net/wireless/intel/iwlwifi/dvm/sta.c:1103 (size 16)
WARNING: CPU: 1 PID: 946 at drivers/net/wireless/intel/iwlwifi/dvm/sta.c:1103 iwlagn_send_sta_key+0x375/0x390 [iwldvm]
<snip>
Hardware name: Dell Inc. Latitude E6430/0H3MT5, BIOS A21 05/08/2017
RIP: 0010:iwlagn_send_sta_key+0x375/0x390 [iwldvm]
<snip>
Call Trace:
<TASK>
iwl_set_dynamic_key+0x1f0/0x220 [iwldvm]
iwlagn_mac_set_key+0x1e4/0x280 [iwldvm]
drv_set_key+0xa4/0x1b0 [mac80211]
ieee80211_key_enable_hw_accel+0xa8/0x2d0 [mac80211]
ieee80211_key_replace+0x22d/0x8e0 [mac80211]
<snip>
Link: https://www.alionet.org/index.php?topic=1469.0
Link: https://lore.kernel.org/linux-wireless/20230218191056.never.374-kees@kernel.org/
Link: https://lore.kernel.org/linux-wireless/68760035-7f75-1b23-e355-bfb758a87d83@redhat.com/
Cc: Kees Cook <keescook@chromium.org>
Suggested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
It is unused and should not be used. In order to avoid limitations in
4-address mode, the driver should always use ieee80211_tx_status_ext for
802.3 frames with a valid sta pointer.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20230417133751.79160-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Start supporting API version 78 for AX devices.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230417113648.5a4dcbf5a2c1.I125808566fe892ee0865e392bf1b1872daafe8ad@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Check the firmware response size for responses to the
memory read/write command in debugfs before using it.
Fixes: 2b55f43f8e47 ("iwlwifi: mvm: Add mem debugfs entry")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230417113648.0d56fcaf68ee.I70e9571f3ed7263929b04f8fabad23c9b999e4ea@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
For MLO support, use the pointer to the peer MLD instead of the default
link station id, since the default link is only used for non-MLO cases.
Using the default link sta id is meaningless for MLO. Also remove the
rcu protected section since we now avoid the lookup based on sta id.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230417113648.40cef48c0592.I8dd666d603d6e1854033e5369c70e78d9303d236@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If the AP station already exists on link activation (which
means we're during link switch), configure the TLC in FW so
we can immediately transmit once the link is activated.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230417113648.1a93de9b7c1f.I42022f24bbe3572f5a082da8c99794ae14281875@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
For MLO, we cannot use vif->bss_conf.chandef.chan->band, since
that will lead to a NULL-ptr dereference as bss_conf isn't used.
However, in case of real MLO, we also need to take both LMACs
into account if they exist, since the station might be active
on both LMACs at the same time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230417113648.3588afc85d79.I11592893bbc191b9548518b8bd782de568a9f848@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Track instead whether or not the station was authorized, that's
clearer than trying to indicate in the code whether or not the
full bandwidth should be used via an 'update' argument.
While at it, give rs_fw_rate_init() the iwl_mvm_ prefix.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230417113648.92bd8d36e311.I1877a109104d5ffeaaad6a623e89f0c44decc38e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When allocating a new link station, initialize the ratescaling
data for it. To do that, refactor the initialization code out
into a new iwl_mvm_rs_add_sta_link() function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230417113648.441b6a8c60fd.I34f1b3555c25aaa22cc34d1112fc3b6393a20b7c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We need to look up the correct version of this struct depending
on the interface type, rather than just checking if the pointer
is non-NULL. Fix that.
Fixes: befebbb30af0 ("iwlwifi: rs: consider LDPC capability in case of HE")
Fixes: b009cf71a982 ("iwlwifi: mvm: only enable HE DCM if we also support TX")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230417113648.1fd54368a02c.Ie4db5e8ae224d9a4a63b528da5d63e1b957b9cef@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Since only clients to an AP can be 20MHz-only STAs, adjust the
code to not make the use of EHT capabilities depend on only the
bandwidth, but also the type of interface.
Fixes: 701404f1091d ("wifi: iwlwifi: rs: add support for parsing max MCS per NSS/BW in 11be")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230417113648.a3a4c931e4a3.I693a07f4d88044c889eee04793883a83bc5ee362@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When this is called it might crash due to the use of
deflink's phy context, update all links instead. It
really shouldn't be called right now though, but it's
better to have safer code until we update this to be
with a link parameter.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230417113648.fd47d0de8319.I87c5e5bcb2fadd70acc32021eed394fc1eea12a4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When we first add the STA before sending an authentication
frame this is false. However, in some cases such as FT or
certainly in MLO link switch scenarios, it will be true.
If it happens to be true, it causes a firmware assert (in
LMAC, 0x2528), because the same bit is used by the firmware
for tracking this setting as well as for tracking if the
management key has been installed, and then we get this
assert from the firmware when installing the MFP key as it
thinks it has already been installed.
Remove the setting for now, until the firmware disentangles
the two. We should be able to set it, in fact we should be
setting it speculatively before authentication/association,
to avoid processing management frames that should have been
protected/encrypted before the key is set.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230417113648.adbeb0e0bfed.I400d0ee3721dc4f294313be992d277ba4d9c88d9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We can allow NL80211_EXT_FEATURE_SCAN_MIN_PREQ_CONTENT since we
just use the elements from mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230417113648.88b1a70365fd.If5030437707ab67e2146291c1517a9b0e31d01ab@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
A long time, ago in commit 818965d39177 ("cfg80211: Allow a
scan request for a specific BSSID"), the stack started passing
the BSSID that should be scanned for. Use it in iwlwifi for the
intended optimisation, and to also allow the use of this for an
implementation sending multi-link probe requests.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230417113648.0be90360cad7.If279c28079a1db34280a824cee7c3f6545fd8b9e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The restriction where MAC ID 0 could be used only for the
managed/IBSS vif is not required when using the new MLO FW API.
Update the driver.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230417113648.e4355615da92.Iba934ccf8589c3c27a25a390dc5e938312889b45@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The firmware no longer wants the beacon template inside the MAC command.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230417113648.92aed4180a06.I277efa343c88081cb3fc890dcbeae3161cdffe16@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add iface_combination declaration to enable concurrent mode. Only two
interfaces under same frequency is supported currently. We limit the
role combination to be STA + P2P or STA + AP only for now until new
feature is requested.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230415035016.15788-2-pkshih@realtek.com
|
|
Power saving for more than one station is not supported currently.
Disallow entering PS mode when we have more than one associated
stations.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230415035016.15788-1-pkshih@realtek.com
|
|
Since firmware can't have proper statistics, driver update the
statistics periodically to firmware to assist in tuning performance.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230415034900.15679-5-pkshih@realtek.com
|
|
Remove macros that set H2C data. Instead, use struct and
le32_encode_bits() with mask definition to make it clean.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230415034900.15679-4-pkshih@realtek.com
|
|
Since we can get the current channel definition each interface maps to,
remove store_op function that is no longer required to make things simple.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230415034900.15679-3-pkshih@realtek.com
|
|
Mac80211 core may ask driver to change to idle mode during HW scan,
then H2C command for HW scan will send failed since chip is in idle
mode. Therefore, We check the SCANNING flag before entering IPS to
prevent this behavior.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230415034900.15679-2-pkshih@realtek.com
|
|
8851B has various hardware module types, so BT coexistence in firmware
needs these information to make decision. Add them to make 8851B work
well.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230412012831.10519-5-pkshih@realtek.com
|
Larry Finger
Sascha Hauer
Po-Hao Huang
Ping-Ke Shih
Yingsha Xu
Avraham Stern
Gregory Greenman
Johannes Berg
Alon Giladi
Mukesh Sisodiya
Hans de Goede
Felix Fietkau
Emmanuel Grumbach
Chih-Kang Chang