| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Use addrconf_addr_gen() to generate IPv6 link-local addresses on GRE
devices in most cases and fall back to using add_v4_addrs() only in
case the GRE configuration is incompatible with addrconf_addr_gen().
GRE used to use addrconf_addr_gen() until commit e5dd729460ca ("ip/ip6_gre:
use the same logic as SIT interfaces when computing v6LL address")
restricted this use to gretap and ip6gretap devices, and created
add_v4_addrs() (borrowed from SIT) for non-Ethernet GRE ones.
The original problem came when commit 9af28511be10 ("addrconf: refuse
isatap eui64 for INADDR_ANY") made __ipv6_isatap_ifid() fail when its
addr parameter was 0. The commit says that this would create an invalid
address, however, I couldn't find any RFC saying that the generated
interface identifier would be wrong. Anyway, since gre over IPv4
devices pass their local tunnel address to __ipv6_isatap_ifid(), that
commit broke their IPv6 link-local address generation when the local
address was unspecified.
Then commit e5dd729460ca ("ip/ip6_gre: use the same logic as SIT
interfaces when computing v6LL address") tried to fix that case by
defining add_v4_addrs() and calling it to generate the IPv6 link-local
address instead of using addrconf_addr_gen() (apart for gretap and
ip6gretap devices, which would still use the regular
addrconf_addr_gen(), since they have a MAC address).
That broke several use cases because add_v4_addrs() isn't properly
integrated into the rest of IPv6 Neighbor Discovery code. Several of
these shortcomings have been fixed over time, but add_v4_addrs()
remains broken on several aspects. In particular, it doesn't send any
Router Sollicitations, so the SLAAC process doesn't start until the
interface receives a Router Advertisement. Also, add_v4_addrs() mostly
ignores the address generation mode of the interface
(/proc/sys/net/ipv6/conf/*/addr_gen_mode), thus breaking the
IN6_ADDR_GEN_MODE_RANDOM and IN6_ADDR_GEN_MODE_STABLE_PRIVACY cases.
Fix the situation by using add_v4_addrs() only in the specific scenario
where the normal method would fail. That is, for interfaces that have
all of the following characteristics:
* run over IPv4,
* transport IP packets directly, not Ethernet (that is, not gretap
interfaces),
* tunnel endpoint is INADDR_ANY (that is, 0),
* device address generation mode is EUI64.
In all other cases, revert back to the regular addrconf_addr_gen().
Also, remove the special case for ip6gre interfaces in add_v4_addrs(),
since ip6gre devices now always use addrconf_addr_gen() instead.
Note:
This patch was originally applied as commit 183185a18ff9 ("gre: Fix
IPv6 link-local address generation."). However, it was then reverted
by commit fc486c2d060f ("Revert "gre: Fix IPv6 link-local address
generation."") because it uncovered another bug that ended up
breaking net/forwarding/ip6gre_custom_multipath_hash.sh. That other
bug has now been fixed by commit 4d0ab3a6885e ("ipv6: Start path
selection from the first nexthop"). Therefore we can now revive this
GRE patch (no changes since original commit 183185a18ff9 ("gre: Fix
IPv6 link-local address generation.").
Fixes: e5dd729460ca ("ip/ip6_gre: use the same logic as SIT interfaces when computing v6LL address")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/a88cc5c4811af36007645d610c95102dccb360a6.1746225214.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Device Tree and Ethernet MAC driver writers often misunderstand RGMII
delays. Rewrite the Normative section in terms of the PCB, is the PCB
adding the 2ns delay. This meaning was previous implied by the
definition, but often wrongly interpreted due to the ambiguous wording
and looking at the definition from the wrong perspective. The new
definition concentrates clearly on the hardware, and should be less
ambiguous.
Add an Informative section to the end of the binding describing in
detail what the four RGMII delays mean. This expands on just the PCB
meaning, adding in the implications for the MAC and PHY.
Additionally, when the MAC or PHY needs to add a delay, which is
software configuration, describe how Linux does this, in the hope of
reducing errors. Make it clear other users of device tree binding may
implement the software configuration in other ways while still
conforming to the binding.
Fixes: 9d3de3c58347 ("dt-bindings: net: Add YAML schemas for the generic Ethernet options")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/20250430-v6-15-rc3-net-rgmii-delays-v2-1-099ae651d5e5@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The selftests added to our CI by Bui Quang Minh recently reveals
that there is a mem leak on the error path of virtnet_xsk_pool_enable():
unreferenced object 0xffff88800a68a000 (size 2048):
comm "xdp_helper", pid 318, jiffies 4294692778
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace (crc 0):
__kvmalloc_node_noprof+0x402/0x570
virtnet_xsk_pool_enable+0x293/0x6a0 (drivers/net/virtio_net.c:5882)
xp_assign_dev+0x369/0x670 (net/xdp/xsk_buff_pool.c:226)
xsk_bind+0x6a5/0x1ae0
__sys_bind+0x15e/0x230
__x64_sys_bind+0x72/0xb0
do_syscall_64+0xc1/0x1d0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Acked-by: Jason Wang <jasowang@redhat.com>
Fixes: e9f3962441c0 ("virtio_net: xsk: rx: support fill with xsk buffer")
Link: https://patch.msgid.link/20250430163836.3029761-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 4bc12818b363 ("virtio-net: disable delayed refill when pausing rx")
fixed a deadlock between reconfig paths and refill work trying to disable
the same NAPI instance. The refill work can't run in parallel with reconfig
because trying to double-disable a NAPI instance causes a stall under the
instance lock, which the reconfig path needs to re-enable the NAPI and
therefore unblock the stalled thread.
There are two cases where we re-enable refill too early. One is in the
virtnet_set_queues() handler. We call it when installing XDP:
virtnet_rx_pause_all(vi);
...
virtnet_napi_tx_disable(..);
...
virtnet_set_queues(..);
...
virtnet_rx_resume_all(..);
We want the work to be disabled until we call virtnet_rx_resume_all(),
but virtnet_set_queues() kicks it before NAPIs were re-enabled.
The other case is a more trivial case of mis-ordering in
__virtnet_rx_resume() found by code inspection.
Taking the spin lock in virtnet_set_queues() (requested during review)
may be unnecessary as we are under rtnl_lock and so are all paths writing
to ->refill_enabled.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Bui Quang Minh <minhquangbui99@gmail.com>
Fixes: 4bc12818b363 ("virtio-net: disable delayed refill when pausing rx")
Fixes: 413f0271f396 ("net: protect NAPI enablement with netdev_lock()")
Link: https://patch.msgid.link/20250430163758.3029367-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Integrate the reproducer from Alan into TC selftests and use scapy to
generate TCP traffic instead of relying on ping command.
Cc: Alan J. Wylie <alan@wylie.me.uk>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Link: https://patch.msgid.link/20250428232955.1740419-3-xiyou.wangcong@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Alan reported a NULL pointer dereference in htb_next_rb_node()
after we made htb_qlen_notify() idempotent.
It turns out in the following case it introduced some regression:
htb_dequeue_tree():
|-> fq_codel_dequeue()
|-> qdisc_tree_reduce_backlog()
|-> htb_qlen_notify()
|-> htb_deactivate()
|-> htb_next_rb_node()
|-> htb_deactivate()
For htb_next_rb_node(), after calling the 1st htb_deactivate(), the
clprio[prio]->ptr could be already set to NULL, which means
htb_next_rb_node() is vulnerable here.
For htb_deactivate(), although we checked qlen before calling it, in
case of qlen==0 after qdisc_tree_reduce_backlog(), we may call it again
which triggers the warning inside.
To fix the issues here, we need to:
1) Make htb_deactivate() idempotent, that is, simply return if we
already call it before.
2) Make htb_next_rb_node() safe against ptr==NULL.
Many thanks to Alan for testing and for the reproducer.
Fixes: 5ba8b837b522 ("sch_htb: make htb_qlen_notify() idempotent")
Reported-by: Alan J. Wylie <alan@wylie.me.uk>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Link: https://patch.msgid.link/20250428232955.1740419-2-xiyou.wangcong@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In case the CMD_RTS got corrupted by interferences, the MSE102x
doesn't allow a retransmission of the command. Instead the Ethernet
frame must be shifted out of the SPI FIFO. Since the actual length is
unknown, assume the maximum possible value.
Fixes: 2f207cbf0dd4 ("net: vertexcom: Add MSE102x SPI support")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250430133043.7722-5-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since there is no protection in the SPI protocol against electrical
interferences, the driver shouldn't blindly trust the length payload
of CMD_RTS. So introduce a bounds check for incoming frames.
Fixes: 2f207cbf0dd4 ("net: vertexcom: Add MSE102x SPI support")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250430133043.7722-4-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The LEN_MASK for CMD_RTS doesn't cover the whole parameter mask.
The Bit 11 is reserved, so adjust LEN_MASK accordingly.
Fixes: 2f207cbf0dd4 ("net: vertexcom: Add MSE102x SPI support")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250430133043.7722-3-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The MSE102x doesn't provide any SPI commands for interrupt handling.
So in case the interrupt fired before the driver requests the IRQ,
the interrupt will never fire again. In order to fix this always poll
for pending packets after opening the interface.
Fixes: 2f207cbf0dd4 ("net: vertexcom: Add MSE102x SPI support")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250430133043.7722-2-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently the ptp_clock_register() is called before relative
ptp resource ready. It may cause unexpected result when upper
layer called the ptp API during the timewindow. Fix it by
moving the ptp_clock_register() to the function end.
Fixes: 0bf5eb788512 ("net: hns3: add support for PTP")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20250430093052.2400464-5-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The size of the tm_qset file of debugfs is limited to 64 KB,
which is too small in the scenario with 1280 qsets.
The size needs to be expanded to 1 MB.
Fixes: 5e69ea7ee2a6 ("net: hns3: refactor the debugfs process")
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20250430093052.2400464-4-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When a VF is passthrough to a VM, and the VM is killed, the reported
interrupt may not been handled, it will remain, and won't be clear by
the nic engine even with a flr or tqp reset. When the VM restart, the
interrupt of the first vector may be dropped by the second enable_irq
in vfio, see the issue below:
https://gitlab.com/qemu-project/qemu/-/issues/2884#note_2423361621
We notice that the vfio has always behaved this way, and the interrupt
is a residue of the nic engine, so we fix the problem by moving the
vector enable process out of the enable_irq loop.
Fixes: 08a100689d4b ("net: hns3: re-organize vector handle")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20250430093052.2400464-3-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The VF driver missed to store the rx VLAN tag strip state when
user change the rx VLAN tag offload state. And it will default
to enable the rx vlan tag strip when re-init VF device after
reset. So if user disable rx VLAN tag offload, and trig reset,
then the HW will still strip the VLAN tag from packet nad fill
into RX BD, but the VF driver will ignore it for rx VLAN tag
offload disabled. It may cause the rx VLAN tag dropped.
Fixes: b2641e2ad456 ("net: hns3: Add support of hardware rx-vlan-offload to HNS3 VF driver")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250430093052.2400464-2-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the host loses heartbeat messages from the device,
the driver calls the device-specific ndo_stop function,
which frees the resources. If the driver is unloaded in
this scenario, it calls ndo_stop again, attempting to free
resources that have already been freed, leading to a host
hang issue. To resolve this, dev_close should be called
instead of the device-specific stop function.dev_close
internally calls ndo_stop to stop the network interface
and performs additional cleanup tasks. During the driver
unload process, if the device is already down, ndo_stop
is not called.
Fixes: 5cb96c29aa0e ("octeon_ep: add heartbeat monitor")
Signed-off-by: Sathesh B Edara <sedara@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250429114624.19104-1-sedara@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Activate TX hang workaround also in
fec_enet_txq_submit_skb() when TSO is not enabled.
Errata: ERR007885
Symptoms: NETDEV WATCHDOG: eth0 (fec): transmit queue 0 timed out
commit 37d6017b84f7 ("net: fec: Workaround for imx6sx enet tx hang when enable three queues")
There is a TDAR race condition for mutliQ when the software sets TDAR
and the UDMA clears TDAR simultaneously or in a small window (2-4 cycles).
This will cause the udma_tx and udma_tx_arbiter state machines to hang.
So, the Workaround is checking TDAR status four time, if TDAR cleared by
hardware and then write TDAR, otherwise don't set TDAR.
Fixes: 53bb20d1faba ("net: fec: add variable reg_desc_active to speed things up")
Signed-off-by: Mattias Barthel <mattias.barthel@atlascopco.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250429090826.3101258-1-mattiasbarthel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Always map the `skb` to the LS descriptor. Previously skb was
mapped to EXT descriptor when the number of fragments is zero with
GSO enabled. Mapping the skb to EXT descriptor prevents it from
being freed, leading to a memory leak
Fixes: 23f0703c125b ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Thangaraj Samynathan <thangaraj.s@microchip.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250429052527.10031-1-thangaraj.s@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On Adva boards, SMA sysfs store/get operations can call
__handle_signal_outputs() or __handle_signal_inputs() while the `irig`
and `dcf` pointers are uninitialized, leading to a NULL pointer
dereference in __handle_signal() and causing a kernel crash. Adva boards
don't use `irig` or `dcf` functionality, so add Adva-specific callbacks
`ptp_ocp_sma_adva_set_outputs()` and `ptp_ocp_sma_adva_set_inputs()` that
avoid invoking `irig` or `dcf` input/output routines.
Fixes: ef61f5528fca ("ptp: ocp: add Adva timecard support")
Signed-off-by: Sagi Maimon <maimon.sagi@gmail.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20250429073320.33277-1-maimon.sagi@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It is possible for a pointer of type struct inet_timewait_sock to be
returned from the functions __inet_lookup_established() and
__inet6_lookup_established(). This can cause a crash when the
returned pointer is of type struct inet_timewait_sock and
sock_put() is called on it. The following is a crash call stack that
shows sk->sk_wmem_alloc being accessed in sk_free() during the call to
sock_put() on a struct inet_timewait_sock pointer. To avoid this issue,
use sock_gen_put() instead of sock_put() when sk->sk_state
is TCP_TIME_WAIT.
mrdump.ko ipanic() + 120
vmlinux notifier_call_chain(nr_to_call=-1, nr_calls=0) + 132
vmlinux atomic_notifier_call_chain(val=0) + 56
vmlinux panic() + 344
vmlinux add_taint() + 164
vmlinux end_report() + 136
vmlinux kasan_report(size=0) + 236
vmlinux report_tag_fault() + 16
vmlinux do_tag_recovery() + 16
vmlinux __do_kernel_fault() + 88
vmlinux do_bad_area() + 28
vmlinux do_tag_check_fault() + 60
vmlinux do_mem_abort() + 80
vmlinux el1_abort() + 56
vmlinux el1h_64_sync_handler() + 124
vmlinux > 0xFFFFFFC080011294()
vmlinux __lse_atomic_fetch_add_release(v=0xF2FFFF82A896087C)
vmlinux __lse_atomic_fetch_sub_release(v=0xF2FFFF82A896087C)
vmlinux arch_atomic_fetch_sub_release(i=1, v=0xF2FFFF82A896087C)
+ 8
vmlinux raw_atomic_fetch_sub_release(i=1, v=0xF2FFFF82A896087C)
+ 8
vmlinux atomic_fetch_sub_release(i=1, v=0xF2FFFF82A896087C) + 8
vmlinux __refcount_sub_and_test(i=1, r=0xF2FFFF82A896087C,
oldp=0) + 8
vmlinux __refcount_dec_and_test(r=0xF2FFFF82A896087C, oldp=0) + 8
vmlinux refcount_dec_and_test(r=0xF2FFFF82A896087C) + 8
vmlinux sk_free(sk=0xF2FFFF82A8960700) + 28
vmlinux sock_put() + 48
vmlinux tcp6_check_fraglist_gro() + 236
vmlinux tcp6_gro_receive() + 624
vmlinux ipv6_gro_receive() + 912
vmlinux dev_gro_receive() + 1116
vmlinux napi_gro_receive() + 196
ccmni.ko ccmni_rx_callback() + 208
ccmni.ko ccmni_queue_recv_skb() + 388
ccci_dpmaif.ko dpmaif_rxq_push_thread() + 1088
vmlinux kthread() + 268
vmlinux 0xFFFFFFC08001F30C()
Fixes: c9d1d23e5239 ("net: add heuristic for enabling TCP fraglist GRO")
Signed-off-by: Jibin Zhang <jibin.zhang@mediatek.com>
Signed-off-by: Shiming Cheng <shiming.cheng@mediatek.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250429020412.14163-1-shiming.cheng@mediatek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Recent updates to the PTP part of bnxt changed the way PTP FIFO is
cleared, skbs waiting for TX timestamps are now cleared during
ndo_close() call. To do clearing procedure, the ptp structure must
exist and point to a valid address. Module destroy sequence had ptp
clear code running before netdev close causing invalid memory access and
kernel crash. Change the sequence to destroy ptp structure after device
close.
Fixes: 8f7ae5a85137 ("bnxt_en: improve TX timestamping FIFO configuration")
Reported-by: Taehee Yoo <ap420073@gmail.com>
Closes: https://lore.kernel.org/netdev/CAMArcTWDe2cd41=ub=zzvYifaYcYv-N-csxfqxUvejy_L0D6UQ@mail.gmail.com/
Signed-off-by: Vadim Fedorenko <vadfed@meta.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Tested-by: Taehee Yoo <ap420073@gmail.com>
Link: https://patch.msgid.link/20250430170343.759126-1-vadfed@meta.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Clang and GCC have different behaviors around disabling warnings
included in -Wall and -Wextra and the order in which flags are
specified, which is exposed by clang's new support for
-Wunterminated-string-initialization.
$ cat test.c
const char foo[3] = "FOO";
const char bar[3] __attribute__((__nonstring__)) = "BAR";
$ clang -fsyntax-only -Wextra test.c
test.c:1:21: warning: initializer-string for character array is too long, array size is 3 but initializer has size 4 (including the null terminating character); did you mean to use the 'nonstring' attribute? [-Wunterminated-string-initialization]
1 | const char foo[3] = "FOO";
| ^~~~~
$ clang -fsyntax-only -Wextra -Wno-unterminated-string-initialization test.c
$ clang -fsyntax-only -Wno-unterminated-string-initialization -Wextra test.c
test.c:1:21: warning: initializer-string for character array is too long, array size is 3 but initializer has size 4 (including the null terminating character); did you mean to use the 'nonstring' attribute? [-Wunterminated-string-initialization]
1 | const char foo[3] = "FOO";
| ^~~~~
$ gcc -fsyntax-only -Wextra test.c
test.c:1:21: warning: initializer-string for array of ‘char’ truncates NUL terminator but destination lacks ‘nonstring’ attribute (4 chars into 3 available) [-Wunterminated-string-initialization]
1 | const char foo[3] = "FOO";
| ^~~~~
$ gcc -fsyntax-only -Wextra -Wno-unterminated-string-initialization test.c
$ gcc -fsyntax-only -Wno-unterminated-string-initialization -Wextra test.c
Move -Wextra up right below -Wall in Makefile.extrawarn to ensure these
flags are at the beginning of the warning options list. Move the couple
of warning options that have been added to the main Makefile since
commit e88ca24319e4 ("kbuild: consolidate warning flags in
scripts/Makefile.extrawarn") to scripts/Makefile.extrawarn after -Wall /
-Wextra to ensure they get properly disabled for all compilers.
Fixes: 9d7a0577c9db ("gcc-15: disable '-Wunterminated-string-initialization' entirely for now")
Link: https://github.com/llvm/llvm-project/issues/10359
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
For version 1 register dump that includes the PCIe stats, the existing
code incorrectly assumes that all PCIe stats are 64-bit values. Fix it
by using an array containing the starting and ending index of the 32-bit
values. The loop in bnxt_get_regs() will use the array to do proper
endian swap for the 32-bit values.
Fixes: b5d600b027eb ("bnxt_en: Add support for 'ethtool -d'")
Reviewed-by: Shruti Parab <shruti.parab@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When retrieving the FW coredump using ethtool, it can sometimes cause
memory corruption:
BUG: KFENCE: memory corruption in __bnxt_get_coredump+0x3ef/0x670 [bnxt_en]
Corrupted memory at 0x000000008f0f30e8 [ ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ] (in kfence-#45):
__bnxt_get_coredump+0x3ef/0x670 [bnxt_en]
ethtool_get_dump_data+0xdc/0x1a0
__dev_ethtool+0xa1e/0x1af0
dev_ethtool+0xa8/0x170
dev_ioctl+0x1b5/0x580
sock_do_ioctl+0xab/0xf0
sock_ioctl+0x1ce/0x2e0
__x64_sys_ioctl+0x87/0xc0
do_syscall_64+0x5c/0xf0
entry_SYSCALL_64_after_hwframe+0x78/0x80
...
This happens when copying the coredump segment list in
bnxt_hwrm_dbg_dma_data() with the HWRM_DBG_COREDUMP_LIST FW command.
The info->dest_buf buffer is allocated based on the number of coredump
segments returned by the FW. The segment list is then DMA'ed by
the FW and the length of the DMA is returned by FW. The driver then
copies this DMA'ed segment list to info->dest_buf.
In some cases, this DMA length may exceed the info->dest_buf length
and cause the above BUG condition. Fix it by capping the copy
length to not exceed the length of info->dest_buf. The extra
DMA data contains no useful information.
This code path is shared for the HWRM_DBG_COREDUMP_LIST and the
HWRM_DBG_COREDUMP_RETRIEVE FW commands. The buffering is different
for these 2 FW commands. To simplify the logic, we need to move
the line to adjust the buffer length for HWRM_DBG_COREDUMP_RETRIEVE
up, so that the new check to cap the copy length will work for both
commands.
Fixes: c74751f4c392 ("bnxt_en: Return error if FW returns more data than dump length")
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Shruti Parab <shruti.parab@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When handling HWRM_DBG_COREDUMP_LIST FW command in
bnxt_hwrm_dbg_dma_data(), the allocated buffer info->dest_buf is
not freed in the error path. In the normal path, info->dest_buf
is assigned to coredump->data and it will eventually be freed after
the coredump is collected.
Free info->dest_buf immediately inside bnxt_hwrm_dbg_dma_data() in
the error path.
Fixes: c74751f4c392 ("bnxt_en: Return error if FW returns more data than dump length")
Reported-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Shruti Parab <shruti.parab@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is similar to the last patch to delay the
pci_alloc_irq_vectors() call in the AER path until after calling
bnxt_reserve_rings(). bnxt_reserve_rings() needs to properly map
the MSIX table first before we call pci_alloc_irq_vectors() which
may immediately write to the MSIX table in some architectures.
Move the bnxt_init_int_mode() call from bnxt_io_slot_reset() to
bnxt_io_resume() after calling bnxt_reserve_rings().
With this change, the AER path may call bnxt_open() ->
bnxt_hwrm_if_change() with bp->irq_tbl set to NULL. bp->irq_tbl is
cleared when we call bnxt_clear_int_mode() in bnxt_io_slot_reset().
So we cannot use !bp->irq_tbl to detect aborted FW reset. Add a
new BNXT_FW_RESET_STATE_ABORT to detect aborted FW reset in
bnxt_hwrm_if_change().
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On some architectures (e.g. ARM), calling pci_alloc_irq_vectors()
will immediately cause the MSIX table to be written. This will not
work if we haven't called bnxt_reserve_rings() to properly map
the MSIX table to the MSIX vectors reserved by FW.
Fix the FW error recovery path to delay the bnxt_init_int_mode() ->
pci_alloc_irq_vectors() call by removing it from bnxt_hwrm_if_change().
bnxt_request_irq() later in the code path will call it and by then the
MSIX table is properly mapped.
Fixes: 4343838ca5eb ("bnxt_en: Replace deprecated PCI MSIX APIs")
Suggested-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If bnxt_rx_vlan() fails because the VLAN protocol ID is invalid,
the SKB is freed but we're missing the call to recycle it. This
may cause the warning:
"page_pool_release_retry() stalled pool shutdown"
Add the missing skb_mark_for_recycle() in bnxt_rx_vlan().
Fixes: 86b05508f775 ("bnxt_en: Use the unified RX page pool buffers for XDP and non-XDP")
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When RDMA driver is loaded, running offline self test is not
supported and driver returns failure early. But it is not clearing
the input buffer and hence the application prints some junk
characters for individual test results.
Fix it by clearing the buffer before returning.
Fixes: 895621f1c816 ("bnxt_en: Don't support offline self test when RoCE driver is loaded")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
WARN_ON() is triggered in __flush_work() if bnxt_init_chip() fails
because we call cancel_work_sync() on dim work that has not been
initialized.
WARNING: CPU: 37 PID: 5223 at kernel/workqueue.c:4201 __flush_work.isra.0+0x212/0x230
The driver relies on the BNXT_STATE_NAPI_DISABLED bit to check if dim
work has already been cancelled. But in the bnxt_open() path,
BNXT_STATE_NAPI_DISABLED is not set and this causes the error
path to think that it needs to cancel the uninitalized dim work.
Fix it by setting BNXT_STATE_NAPI_DISABLED during initialization.
The bit will be cleared when we enable NAPI and initialize dim work.
Fixes: 40452969a506 ("bnxt_en: Fix DIM shutdown")
Suggested-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Shravya KN <shravya.k-n@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If any address or port is changed, update it in all packets and recalculate
checksum.
Fixes: 9fd1ff5d2ac7 ("udp: Support UDP fraglist GRO/GSO.")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250426153210.14044-1-nbd@nbd.name
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a forwarding path test for tc-taprio, based on isochron. This is
specifically intended for NICs with an offloaded data path (switchdev/DSA)
and requires taprio 'flags 2'. Also, $h1 and $h2 must support hardware
timestamping, and $h1 tc-etf offload, for isochron to work.
Packets received by a switch while the egress port has a taprio schedule
with an open gate for the traffic class must be sent right away.
Packets received by the switch while the traffic class gate must be
delayed until it opens.
Packets received by the switch must be dropped if the gate for the
traffic class never opens.
Packets should pass if the maximum SDU for the traffic class allows it,
and should be dropped otherwise.
The schedule should auto-update itself if clock jumps take place while
taprio is installed. Repeat most of the above tests after forcing two
clock jumps, one backwards (in Jan 1970) and one back into the present.
Symlink it from tools/testing/selftests/drivers/net/dsa, because usually
DSA ports have the same MAC address, and we need STABLE_MAC_ADDRS=yes
from its forwarding.config for the test to run successfully.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250426144859.3128352-5-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Make out-of-band testing (send a packet when its traffic class gate is
closed, expecting it to be delayed) more predictable by allowing the
window size to be customized by isochron_do().
From man isochron-send, the window size alters the advance time (the
delta between the transmission time of the packet, and its expected TX
time when using SO_TXTIME or tc-taprio on the sender). In absence of the
argument, isochron-send defaults to maximizing the advance time (making
it equal to the cycle length).
The default behavior is exactly what is problematic. An advance time
that is too large will make packets intended to be out-of-band still be
potentially in-band with an open gate from the schedule's previous cycle.
We need to allow that advance time to be reduced.
Perhaps a bit confusingly, isochron_do() has a shift_time argument
currently, but that does not help here. The shift time shifts both the
user space wakeup time and the expected TX time by equal amounts, it is
unable of bringing them closer to one another.
Set the window size properly for the Ocelot PSFP selftest as well.
That used to work due to a very carefully chosen SHIFT_TIME_NS.
I've re-tested that the test still works properly.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250426144859.3128352-4-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This snippet will be necessary for a future isochron-based test, so
provide a simpler high-level interface for counting the received
packets.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250426144859.3128352-3-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Simplest setup to reproduce the issue: connect 2 ports of the
LS1028A-RDB together (eno0 with swp0) and run:
$ ip link set eno0 up && ip link set swp0 up
$ tc qdisc replace dev swp0 parent root handle 100 taprio num_tc 8 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 map 0 1 2 3 4 5 6 7 \
base-time 0 sched-entry S 20 300000 sched-entry S 10 200000 \
sched-entry S 20 300000 sched-entry S 48 200000 \
sched-entry S 20 300000 sched-entry S 83 200000 \
sched-entry S 40 300000 sched-entry S 00 200000 flags 2
$ ptp4l -i eno0 -f /etc/linuxptp/configs/gPTP.cfg -m &
$ ptp4l -i swp0 -f /etc/linuxptp/configs/gPTP.cfg -m
One will observe that the PTP state machine on swp0 starts
synchronizing, then it attempts to do a clock step, and after that, it
never fails to recover from the condition below.
ptp4l[82.427]: selected best master clock 00049f.fffe.05f627
ptp4l[82.428]: port 1 (swp0): MASTER to UNCALIBRATED on RS_SLAVE
ptp4l[83.252]: port 1 (swp0): UNCALIBRATED to SLAVE on MASTER_CLOCK_SELECTED
ptp4l[83.886]: rms 4537731277 max 9075462553 freq -18518 +/- 11467 delay 818 +/- 0
ptp4l[84.170]: timed out while polling for tx timestamp
ptp4l[84.171]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[84.172]: port 1 (swp0): send peer delay request failed
ptp4l[84.173]: port 1 (swp0): clearing fault immediately
ptp4l[84.269]: port 1 (swp0): SLAVE to LISTENING on INIT_COMPLETE
ptp4l[85.303]: timed out while polling for tx timestamp
ptp4l[84.171]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[84.172]: port 1 (swp0): send peer delay request failed
ptp4l[84.173]: port 1 (swp0): clearing fault immediately
ptp4l[84.269]: port 1 (swp0): SLAVE to LISTENING on INIT_COMPLETE
ptp4l[85.303]: timed out while polling for tx timestamp
ptp4l[85.304]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[85.305]: port 1 (swp0): send peer delay response failed
ptp4l[85.306]: port 1 (swp0): clearing fault immediately
ptp4l[86.304]: timed out while polling for tx timestamp
A hint is given by the non-zero statistics for dropped packets which
were expecting hardware TX timestamps:
$ ethtool --include-statistics -T swp0
(...)
Statistics:
tx_pkts: 30
tx_lost: 11
tx_err: 0
We know that when PTP clock stepping takes place (from ocelot_ptp_settime64()
or from ocelot_ptp_adjtime()), vsc9959_tas_clock_adjust() is called.
Another interesting hint is that placing an early return in
vsc9959_tas_clock_adjust(), so as to neutralize this function, fixes the
issue and TX timestamps are no longer dropped.
The debugging function written by me and included below is intended to
read the GCL RAM, after the admin schedule became operational, through
the two status registers available for this purpose:
QSYS_GCL_STATUS_REG_1 and QSYS_GCL_STATUS_REG_2.
static void vsc9959_print_tas_gcl(struct ocelot *ocelot)
{
u32 val, list_length, interval, gate_state;
int i, err;
err = read_poll_timeout(ocelot_read, val,
!(val & QSYS_PARAM_STATUS_REG_8_CONFIG_PENDING),
10, 100000, false, ocelot, QSYS_PARAM_STATUS_REG_8);
if (err) {
dev_err(ocelot->dev,
"Failed to wait for TAS config pending bit to clear: %pe\n",
ERR_PTR(err));
return;
}
val = ocelot_read(ocelot, QSYS_PARAM_STATUS_REG_3);
list_length = QSYS_PARAM_STATUS_REG_3_LIST_LENGTH_X(val);
dev_info(ocelot->dev, "GCL length: %u\n", list_length);
for (i = 0; i < list_length; i++) {
ocelot_rmw(ocelot,
QSYS_GCL_STATUS_REG_1_GCL_ENTRY_NUM(i),
QSYS_GCL_STATUS_REG_1_GCL_ENTRY_NUM_M,
QSYS_GCL_STATUS_REG_1);
interval = ocelot_read(ocelot, QSYS_GCL_STATUS_REG_2);
val = ocelot_read(ocelot, QSYS_GCL_STATUS_REG_1);
gate_state = QSYS_GCL_STATUS_REG_1_GATE_STATE_X(val);
dev_info(ocelot->dev, "GCL entry %d: states 0x%x interval %u\n",
i, gate_state, interval);
}
}
Calling it from two places: after the initial QSYS_TAS_PARAM_CFG_CTRL_CONFIG_CHANGE
performed by vsc9959_qos_port_tas_set(), and after the one done by
vsc9959_tas_clock_adjust(), I notice the following difference.
From the tc-taprio process context, where the schedule was initially
configured, the GCL looks like this:
mscc_felix 0000:00:00.5: GCL length: 8
mscc_felix 0000:00:00.5: GCL entry 0: states 0x20 interval 300000
mscc_felix 0000:00:00.5: GCL entry 1: states 0x10 interval 200000
mscc_felix 0000:00:00.5: GCL entry 2: states 0x20 interval 300000
mscc_felix 0000:00:00.5: GCL entry 3: states 0x48 interval 200000
mscc_felix 0000:00:00.5: GCL entry 4: states 0x20 interval 300000
mscc_felix 0000:00:00.5: GCL entry 5: states 0x83 interval 200000
mscc_felix 0000:00:00.5: GCL entry 6: states 0x40 interval 300000
mscc_felix 0000:00:00.5: GCL entry 7: states 0x0 interval 200000
But from the ptp4l clock stepping process context, when the
vsc9959_tas_clock_adjust() hook is called, the GCL RAM of the
operational schedule now looks like this:
mscc_felix 0000:00:00.5: GCL length: 8
mscc_felix 0000:00:00.5: GCL entry 0: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 1: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 2: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 3: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 4: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 5: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 6: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 7: states 0x0 interval 0
I do not have a formal explanation, just experimental conclusions.
It appears that after triggering QSYS_TAS_PARAM_CFG_CTRL_CONFIG_CHANGE
for a port's TAS, the GCL entry RAM is updated anyway, despite what the
documentation claims: "Specify the time interval in
QSYS::GCL_CFG_REG_2.TIME_INTERVAL. This triggers the actual RAM
write with the gate state and the time interval for the entry number
specified". We don't touch that register (through vsc9959_tas_gcl_set())
from vsc9959_tas_clock_adjust(), yet the GCL RAM is updated anyway.
It seems to be updated with effectively stale memory, which in my
testing can hold a variety of things, including even pieces of the
previously applied schedule, for particular schedule lengths.
As such, in most circumstances it is very difficult to pinpoint this
issue, because the newly updated schedule would "behave strangely",
but ultimately might still pass traffic to some extent, due to some
gate entries still being present in the stale GCL entry RAM. It is easy
to miss.
With the particular schedule given at the beginning, the GCL RAM
"happens" to be reproducibly rewritten with all zeroes, and this is
consistent with what we see: when the time-aware shaper has gate entries
with all gates closed, traffic is dropped on TX, no wonder we can't
retrieve TX timestamps.
Rewriting the GCL entry RAM when reapplying the new base time fixes the
observed issue.
Fixes: 8670dc33f48b ("net: dsa: felix: update base time of time-aware shaper when adjusting PTP time")
Reported-by: Richie Pearn <richard.pearn@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250426144859.3128352-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If the mtk_poll_rx() function detects the MTK_RESETTING flag, it will
jump to release_desc and refill the high word of the SDP on the 4GB RFB.
Subsequently, mtk_rx_clean will process an incorrect SDP, leading to a
panic.
Add patch from MediaTek's SDK to resolve this.
Fixes: 2d75891ebc09 ("net: ethernet: mtk_eth_soc: support 36-bit DMA addressing on MT7988")
Link: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/71f47ea785699c6aa3b922d66c2bdc1a43da25b1
Signed-off-by: Chad Monroe <chad@monroe.io>
Link: https://patch.msgid.link/4adc2aaeb0fb1b9cdc56bf21cf8e7fa328daa345.1745715843.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 1a931c4f5e68 ("igc: add lock preventing multiple simultaneous PTM
transactions") added a new mutex to protect concurrent PTM transactions.
This lock is acquired in igc_ptp_reset() in order to ensure the PTM
registers are properly disabled after a device reset.
The flow where the lock is acquired already holds a spinlock, so acquiring
a mutex leads to a sleep-while-locking bug, reported both by smatch,
and the kernel test robot.
The critical section in igc_ptp_reset() does correctly use the
readx_poll_timeout_atomic variants, but the standard PTM flow uses regular
sleeping variants. This makes converting the mutex to a spinlock a bit
tricky.
Instead, re-order the locking in igc_ptp_reset. Acquire the mutex first,
and then the tmreg_lock spinlock. This is safe because there is no other
ordering dependency on these locks, as this is the only place where both
locks were acquired simultaneously. Indeed, any other flow acquiring locks
in that order would be wrong regardless.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Fixes: 1a931c4f5e68 ("igc: add lock preventing multiple simultaneous PTM transactions")
Link: https://lore.kernel.org/intel-wired-lan/Z_-P-Hc1yxcw0lTB@stanley.mountain/
Link: https://lore.kernel.org/intel-wired-lan/202504211511.f7738f5d-lkp@intel.com/T/#u
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Before the referenced commit, the shutdown just called idpf_remove(),
this way IDPF_REMOVE_IN_PROG was protecting us from the serv_task
rescheduling reset. Without this flag set the shutdown process is
vulnerable to HW reset or any other triggering conditions (such as
default mailbox being destroyed).
When one of conditions checked in idpf_service_task becomes true,
vc_event_task can be rescheduled during shutdown, this leads to accessing
freed memory e.g. idpf_req_rel_vector_indexes() trying to read
vport->q_vector_idxs. This in turn causes the system to become defunct
during e.g. systemctl kexec.
Considering using IDPF_REMOVE_IN_PROG would lead to more heavy shutdown
process, instead just cancel the serv_task before cancelling
adapter->serv_task before cancelling adapter->vc_event_task to ensure that
reset will not be scheduled while we are doing a shutdown.
Fixes: 4c9106f4906a ("idpf: fix adapter NULL pointer dereference on reboot")
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In case of failing on rss_data->rss_key allocation the function is
freeing vport without freeing earlier allocated q_vector_idxs. Fix it.
Move from freeing in error branch to goto scheme.
Fixes: d4d558718266 ("idpf: initialize interrupts and enable vport")
Reviewed-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Suggested-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
This bit is necessary to receive packets from the internal PHY.
Without this bit set, no activity occurs on the interface.
Normally u-boot sets this bit, but if u-boot is compiled without
net support, the interface will be up but without any activity.
If bit is set once, it will work until the IP is powered down or reset.
The vendor SDK sets this bit along with the PHY_ID bits.
Signed-off-by: Da Xue <da@libre.computer>
Fixes: 9a24e1ff4326 ("net: mdio: add amlogic gxl mdio mux support")
Link: https://patch.msgid.link/20250425192009.1439508-1-da@libre.computer
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As it's name suggests, parse_eeprom() parses EEPROM data.
This is done by reading data, 16 bits at a time as follows:
for (i = 0; i < 128; i++)
((__le16 *) sromdata)[i] = cpu_to_le16(read_eeprom(np, i));
sromdata is at the same memory location as psrom.
And the type of psrom is a pointer to struct t_SROM.
As can be seen in the loop above, data is stored in sromdata, and thus psrom,
as 16-bit little-endian values.
However, the integer fields of t_SROM are host byte order integers.
And in the case of led_mode this leads to a little endian value
being incorrectly treated as host byte order.
Looking at rio_set_led_mode, this does appear to be a bug as that code
masks led_mode with 0x1, 0x2 and 0x8. Logic that would be effected by a
reversed byte order.
This problem would only manifest on big endian hosts.
Found by inspection while investigating a sparse warning
regarding the crc field of t_SROM.
I believe that warning is a false positive. And although I plan
to send a follow-up to use little-endian types for other the integer
fields of PSROM_t I do not believe that will involve any bug fixes.
Compile tested only.
Fixes: c3f45d322cbd ("dl2k: Add support for IP1000A-based cards")
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250425-dlink-led-mode-v1-1-6bae3c36e736@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Split offloads into csum, tso and other offloads so that tunneled
packets do not by default have all the offloads enabled.
Stateless offloads for encapsulated packets are not yet supported in
firmware/software but in the driver we were setting the features same as
non encapsulated features.
Fixed naming to clarify CSUM bits are being checked for Tx.
Inherit netdev features to VLAN interfaces as well.
Fixes: 0fe45467a104 ("idpf: add create vport and netdev configuration")
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Madhu Chittim <madhu.chittim@intel.com>
Tested-by: Zachary Goldstein <zachmgoldstein@google.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250425222636.3188441-4-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As mentioned in the commit baeb705fd6a7 ("ice: always check VF VSI
pointer values"), we need to perform a null pointer check on the return
value of ice_get_vf_vsi() before using it.
Fixes: 6ebbe97a4881 ("ice: Add a per-VF limit on number of FDIR filters")
Signed-off-by: Xuanqiang Luo <luoxuanqiang@kylinos.cn>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250425222636.3188441-3-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The Get Tx Topology AQ command (opcode 0x0418) has different read flag
requirements depending on the hardware/firmware. For E810, E822, and E823
firmware the read flag must be set, and for newer hardware (E825 and E830)
it must not be set.
This results in failure to configure Tx topology and the following warning
message during probe:
DDP package does not support Tx scheduling layers switching feature -
please update to the latest DDP package and try again
The current implementation only handles E825-C but not E830. It is
confusing as we first check ice_is_e825c() and then set the flag in the set
case. Finally, we check ice_is_e825c() again and set the flag for all other
hardware in both the set and get case.
Instead, notice that we always need the read flag for set, but only need
the read flag for get on E810, E822, and E823 firmware. Fix the logic to
check the MAC type and set the read flag in get only on the older devices
which require it.
Fixes: ba1124f58afd ("ice: Add E830 device IDs, MAC type and registers")
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250425222636.3188441-2-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add 5 TDC tests that exercise the reentrant enqueue behaviour in drr,
ets, qfq, and hfsc:
- Test DRR's enqueue reentrant behaviour with netem (which caused a
double list add)
- Test ETS's enqueue reentrant behaviour with netem (which caused a double
list add)
- Test QFQ's enqueue reentrant behaviour with netem (which caused a double
list add)
- Test HFSC's enqueue reentrant behaviour with netem (which caused a UAF)
- Test nested DRR's enqueue reentrant behaviour with netem (which caused a
double list add)
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Victor Nogueira <victor@mojatatu.com>
Link: https://patch.msgid.link/20250425220710.3964791-6-victor@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As described in Gerrard's report [1], there are use cases where a netem
child qdisc will make the parent qdisc's enqueue callback reentrant.
In the case of qfq, there won't be a UAF, but the code will add the same
classifier to the list twice, which will cause memory corruption.
This patch checks whether the class was already added to the agg->active
list (cl_is_active) before doing the addition to cater for the reentrant
case.
[1] https://lore.kernel.org/netdev/CAHcdcOm+03OD2j6R0=YHKqmy=VgJ8xEOKuP6c7mSgnp-TEJJbw@mail.gmail.com/
Fixes: 37d9cf1a3ce3 ("sched: Fix detection of empty queues in child qdiscs")
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Victor Nogueira <victor@mojatatu.com>
Link: https://patch.msgid.link/20250425220710.3964791-5-victor@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As described in Gerrard's report [1], there are use cases where a netem
child qdisc will make the parent qdisc's enqueue callback reentrant.
In the case of ets, there won't be a UAF, but the code will add the same
classifier to the list twice, which will cause memory corruption.
In addition to checking for qlen being zero, this patch checks whether
the class was already added to the active_list (cl_is_active) before
doing the addition to cater for the reentrant case.
[1] https://lore.kernel.org/netdev/CAHcdcOm+03OD2j6R0=YHKqmy=VgJ8xEOKuP6c7mSgnp-TEJJbw@mail.gmail.com/
Fixes: 37d9cf1a3ce3 ("sched: Fix detection of empty queues in child qdiscs")
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Victor Nogueira <victor@mojatatu.com>
Link: https://patch.msgid.link/20250425220710.3964791-4-victor@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As described in Gerrard's report [1], we have a UAF case when an hfsc class
has a netem child qdisc. The crux of the issue is that hfsc is assuming
that checking for cl->qdisc->q.qlen == 0 guarantees that it hasn't inserted
the class in the vttree or eltree (which is not true for the netem
duplicate case).
This patch checks the n_active class variable to make sure that the code
won't insert the class in the vttree or eltree twice, catering for the
reentrant case.
[1] https://lore.kernel.org/netdev/CAHcdcOm+03OD2j6R0=YHKqmy=VgJ8xEOKuP6c7mSgnp-TEJJbw@mail.gmail.com/
Fixes: 37d9cf1a3ce3 ("sched: Fix detection of empty queues in child qdiscs")
Reported-by: Gerrard Tai <gerrard.tai@starlabs.sg>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Victor Nogueira <victor@mojatatu.com>
Link: https://patch.msgid.link/20250425220710.3964791-3-victor@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As described in Gerrard's report [1], there are use cases where a netem
child qdisc will make the parent qdisc's enqueue callback reentrant.
In the case of drr, there won't be a UAF, but the code will add the same
classifier to the list twice, which will cause memory corruption.
In addition to checking for qlen being zero, this patch checks whether the
class was already added to the active_list (cl_is_active) before adding
to the list to cover for the reentrant case.
[1] https://lore.kernel.org/netdev/CAHcdcOm+03OD2j6R0=YHKqmy=VgJ8xEOKuP6c7mSgnp-TEJJbw@mail.gmail.com/
Fixes: 37d9cf1a3ce3 ("sched: Fix detection of empty queues in child qdiscs")
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Victor Nogueira <victor@mojatatu.com>
Link: https://patch.msgid.link/20250425220710.3964791-2-victor@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A use-after-free error popped up in stress testing:
[Mon Apr 21 21:21:33 2025] BUG: KFENCE: use-after-free write in pdsc_auxbus_dev_del+0xef/0x160 [pds_core]
[Mon Apr 21 21:21:33 2025] Use-after-free write at 0x000000007013ecd1 (in kfence-#47):
[Mon Apr 21 21:21:33 2025] pdsc_auxbus_dev_del+0xef/0x160 [pds_core]
[Mon Apr 21 21:21:33 2025] pdsc_remove+0xc0/0x1b0 [pds_core]
[Mon Apr 21 21:21:33 2025] pci_device_remove+0x24/0x70
[Mon Apr 21 21:21:33 2025] device_release_driver_internal+0x11f/0x180
[Mon Apr 21 21:21:33 2025] driver_detach+0x45/0x80
[Mon Apr 21 21:21:33 2025] bus_remove_driver+0x83/0xe0
[Mon Apr 21 21:21:33 2025] pci_unregister_driver+0x1a/0x80
The actual device uninit usually happens on a separate thread
scheduled after this code runs, but there is no guarantee of order
of thread execution, so this could be a problem. There's no
actual need to clear the client_id at this point, so simply
remove the offending code.
Fixes: 10659034c622 ("pds_core: add the aux client API")
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250425203857.71547-1-shannon.nelson@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The phy-upstream enum is already defined in the ethtool.h UAPI header
and used by the ethtool userspace tool. However, the ethtool spec does
not reference it, causing YNL to auto-generate a duplicate and redundant
enum.
Fix this by updating the spec to reference the existing UAPI enum
in ethtool.h.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20250425171419.947352-1-kory.maincent@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
Guillaume Nault
Andrew Lunn
Jakub Kicinski
Cong Wang
Stefan Wahren
Jian Shen
Hao Lan
Yonglong Liu
Sathesh B Edara
Mattias Barthel
Thangaraj Samynathan
Sagi Maimon
Jibin Zhang
Vadim Fedorenko
Nathan Chancellor
Michael Chan
Shruti Parab
Kashyap Desai
Somnath Kotur
Kalesh AP
Shravya KN
Felix Fietkau
Vladimir Oltean
Chad Monroe
Jacob Keller
Larysa Zaremba
Michal Swiatkowski
Da Xue
Simon Horman
Madhu Chittim
Xuanqiang Luo
Paul Greenwalt
Victor Nogueira
Shannon Nelson
Kory Maincent