| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
thermal_zone_device_check --> thermal_zone_device_update -->
handle_thermal_trip --> handle_critical_trips --> orderly_poweroff
The above sequence happens every 250/500 mS based on the configuration.
The orderly_poweroff function is getting called every 250/500 mS.
With a full fledged file system it takes at least 5-10 Seconds to
power off gracefully.
In that period due to the thermal_zone_device_check triggering
periodically the thermal work queues bombard with
orderly_poweroff calls multiple times eventually leading to
failures in gracefully powering off the system.
Make sure that orderly_poweroff is called only once.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
The interrupt request call in Intel SoC DTS driver may fail if
there is no underlying BIOS support. However, the user space
thermal daemon can still use the thermal zones created by the
SoC DTS driver in polling mode, therefore, instead of bailing
out on interrupt request failures, it is better just to log
a warning message and continue the init process.
Signed-off-by: Brian Bian <brian.bian@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
This patch adds another parameter to the trace function:
trace_thermal_power_devfreq_get_power().
In case when we call directly driver's code for the real power,
we do not have static/dynamic_power values. Instead we get total
power in the '*power' value. The 'static_power' and
'dynamic_power' are set to 0.
Therefore, we have to trace that '*power' value in this scenario.
CC: Steven Rostedt <rostedt@goodmis.org>
CC: Ingo Molnar <mingo@redhat.com>
CC: Zhang Rui <rui.zhang@intel.com>
CC: Eduardo Valentin <edubezval@gmail.com>
Acked-by: Javi Merino <javi.merino@kernel.org>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
|
|
This patch introduces a new interface for device drivers connected to
devfreq_cooling in the thermal framework: get_real_power().
Some devices have more sophisticated methods (like power counters)
to approximate the actual power that they use.
In the previous implementation we had a pre-calculated power
table which was then scaled by 'utilization'
('busy_time' and 'total_time' taken from devfreq 'last_status').
With this new interface the driver can provide more precise data
regarding actual power to the thermal governor every time the power
budget is calculated. We then use this value and calculate the real
resource utilization scaling factor.
Reviewed-by: Chris Diamand <chris.diamand@arm.com>
Acked-by: Javi Merino <javi.merino@kernel.org>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
|
|
Move the code which gets the voltage for a given frequency.
This code will be resused in few places.
Acked-by: Javi Merino <javi.merino@kernel.org>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
|
|
If thermal bank with 4 sensors, thermal driver should read TEMP_MSR3.
However, currently thermal driver would not read TEMP_MSR3 since mt8173
thermal driver only use 3 sensors on each thermal bank at the same time,
so this patch would not effect temperature.
Only if mt mt8173 thermal driver use 4 sensors on any thermal bank, would
read third sensor two times, and lose fourth sensor of vale.
cc: stable@vger.kernel.org
Fixes: b7cf0053738c ("thermal: Add Mediatek thermal driver for mt2701.")
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Dawei Chien <dawei.chien@mediatek.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
We already have 2 Broadcom drivers and at least 1 more is coming. This
made us create broadcom subdirectory where bcm2835 should be moves now.
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
Just in case someone uses modinfo to find (blame) me.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
|
|
In the case that compat_get_bitmap fails we do not want to copy the
bitmap to the user as it will contain uninitialized stack data and leak
sensitive data.
Signed-off-by: Chris Salls <salls@cs.ucsb.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently, inputting the following command will succeed but actually the
value will be truncated:
# echo 0x12ffffffff > /proc/sys/net/ipv4/tcp_notsent_lowat
This is not friendly to the user, so instead, we should report error
when the value is larger than UINT_MAX.
Fixes: e7d316a02f68 ("sysctl: handle error writing UINT_MAX to u32 fields")
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Cc: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Separate out kernfs from driver core and add myself as a
co-maintainer.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ops->show() can return a negative error code.
Commit 65da3484d9be ("sysfs: correctly handle short reads on PREALLOC attrs.")
(in v4.4) caused this to be stored in an unsigned 'size_t' variable, so errors
would look like large numbers.
As a result, if an error is returned, sysfs_kf_read() will return the
value of 'count', typically 4096.
Commit 17d0774f8068 ("sysfs: correctly handle read offset on PREALLOC attrs")
(in v4.8) extended this error to use the unsigned large 'len' as a size for
memmove().
Consequently, if ->show returns an error, then the first read() on the
sysfs file will return 4096 and could return uninitialized memory to
user-space.
If the application performs a subsequent read, this will trigger a memmove()
with extremely large count, and is likely to crash the machine is bizarre ways.
This bug can currently only be triggered by reading from an md
sysfs attribute declared with __ATTR_PREALLOC() during the
brief period between when mddev_put() deletes an mddev from
the ->all_mddevs list, and when mddev_delayed_delete() - which is
scheduled on a workqueue - completes.
Before this, an error won't be returned by the ->show()
After this, the ->show() won't be called.
I can reproduce it reliably only by putting delay like
usleep_range(500000,700000);
early in mddev_delayed_delete(). Then after creating an
md device md0 run
echo clear > /sys/block/md0/md/array_state; cat /sys/block/md0/md/array_state
The bug can be triggered without the usleep.
Fixes: 65da3484d9be ("sysfs: correctly handle short reads on PREALLOC attrs.")
Fixes: 17d0774f8068 ("sysfs: correctly handle read offset on PREALLOC attrs")
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.com>
Acked-by: Tejun Heo <tj@kernel.org>
Reported-and-tested-by: Miroslav Benes <mbenes@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A patch documenting how to specify which kernels a particular fix should
be backported to (seemingly) inadvertently added a minus sign after the
kernel version. This particular stable-tag format had never been used
prior to this patch, and was neither present when the patch in question
was first submitted (it was added in v2 without any comment).
Drop the minus sign to avoid any confusion.
Fixes: fdc81b7910ad ("stable_kernel_rules: Add clause about specification of kernel versions to patch.")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
vfs_llseek will check whether the file mode has
FMODE_LSEEK, no return failure. But ashmem can be
lseek, so add FMODE_LSEEK to ashmem file.
Comment From Greg Hackmann:
ashmem_llseek() passes the llseek() call through to the backing
shmem file. 91360b02ab48 ("ashmem: use vfs_llseek()") changed
this from directly calling the file's llseek() op into a VFS
layer call. This also adds a check for the FMODE_LSEEK bit, so
without that bit ashmem_llseek() now always fails with -ESPIPE.
Fixes: 91360b02ab48 ("ashmem: use vfs_llseek()")
Signed-off-by: Shuxiao Zhang <zhangshuxiao@xiaomi.com>
Tested-by: Greg Hackmann <ghackmann@google.com>
Cc: stable <stable@vger.kernel.org> # 3.18+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We currently have 2 specific WQ_RECLAIM workqueues in the mm code.
vmstat_wq for updating pcp stats and lru_add_drain_wq dedicated to drain
per cpu lru caches. This seems more than necessary because both can run
on a single WQ. Both do not block on locks requiring a memory
allocation nor perform any allocations themselves. We will save one
rescuer thread this way.
On the other hand drain_all_pages() queues work on the system wq which
doesn't have rescuer and so this depend on memory allocation (when all
workers are stuck allocating and new ones cannot be created).
Initially we thought this would be more of a theoretical problem but
Hugh Dickins has reported:
: 4.11-rc has been giving me hangs after hours of swapping load. At
: first they looked like memory leaks ("fork: Cannot allocate memory");
: but for no good reason I happened to do "cat /proc/sys/vm/stat_refresh"
: before looking at /proc/meminfo one time, and the stat_refresh stuck
: in D state, waiting for completion of flush_work like many kworkers.
: kthreadd waiting for completion of flush_work in drain_all_pages().
This worker should be using WQ_RECLAIM as well in order to guarantee a
forward progress. We can reuse the same one as for lru draining and
vmstat.
Link: http://lkml.kernel.org/r/20170307131751.24936-1-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Suggested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Mel Gorman <mgorman@suse.de>
Tested-by: Yang Li <pku.leo@gmail.com>
Tested-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Set current email address to replace previous employers email addresses.
Link: http://lkml.kernel.org/r/1491450722-6633-1-git-send-email-jeffy.chen@rock-chips.com
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We got need_resched() warnings in swap_cgroup_swapoff() because
swap_cgroup_ctrl[type].length is particularly large.
Reschedule when needed.
Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1704061315270.80559@chino.kir.corp.google.com
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
While running generic/340 in my test setup I hit the following race. It
can happen with kernels that support FS DAX PMDs, so v4.10 thru
v4.11-rc5.
Thread 1 Thread 2
-------- --------
dax_iomap_pmd_fault()
grab_mapping_entry()
spin_lock_irq()
get_unlocked_mapping_entry()
'entry' is NULL, can't call lock_slot()
spin_unlock_irq()
radix_tree_preload()
dax_iomap_pmd_fault()
grab_mapping_entry()
spin_lock_irq()
get_unlocked_mapping_entry()
...
lock_slot()
spin_unlock_irq()
dax_pmd_insert_mapping()
<inserts a PMD mapping>
spin_lock_irq()
__radix_tree_insert() fails with -EEXIST
<fall back to 4k fault, and die horribly
when inserting a 4k entry where a PMD exists>
The issue is that we have to drop mapping->tree_lock while calling
radix_tree_preload(), but since we didn't have a radix tree entry to
lock (unlike in the pmd_downgrade case) we have no protection against
Thread 2 coming along and inserting a PMD at the same index. For 4k
entries we handled this with a special-case response to -EEXIST coming
from the __radix_tree_insert(), but this doesn't save us for PMDs
because the -EEXIST case can also mean that we collided with a 4k entry
in the radix tree at a different index, but one that is covered by our
PMD range.
So, correctly handle both the 4k and 2M collision cases by explicitly
re-checking the radix tree for an entry at our index once we reacquire
mapping->tree_lock.
This patch has made it through a clean xfstests run with the current
v4.11-rc5 based linux/master, and it also ran generic/340 500 times in a
loop. It used to fail within the first 10 iterations.
Link: http://lkml.kernel.org/r/20170406212944.2866-1-ross.zwisler@linux.intel.com
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: "Darrick J. Wong" <darrick.wong@oracle.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: <stable@vger.kernel.org> [4.10+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Setting thp defrag mode of "defer+madvise" actually sets "defer" in the
kernel due to the name similarity and the out-of-order way the string is
checked in defrag_store().
Check the string in the correct order so that
TRANSPARENT_HUGEPAGE_DEFRAG_KSWAPD_OR_MADV_FLAG is set appropriately for
"defer+madvise".
Fixes: 21440d7eb904 ("mm, thp: add new defer+madvise defrag option")
Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1704051814420.137626@chino.kir.corp.google.com
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In PT_SEIZED + LISTEN mode STOP/CONT signals cause a wakeup against
__TASK_TRACED. If this races with the ptrace_unfreeze_traced at the end
of a PTRACE_LISTEN, this can wake the task /after/ the check against
__TASK_TRACED, but before the reset of state to TASK_TRACED. This
causes it to instead clobber TASK_WAKING, allowing a subsequent wakeup
against TRACED while the task is still on the rq wake_list, corrupting
it.
Oleg said:
"The kernel can crash or this can lead to other hard-to-debug problems.
In short, "task->state = TASK_TRACED" in ptrace_unfreeze_traced()
assumes that nobody else can wake it up, but PTRACE_LISTEN breaks the
contract. Obviusly it is very wrong to manipulate task->state if this
task is already running, or WAKING, or it sleeps again"
[akpm@linux-foundation.org: coding-style fixes]
Fixes: 9899d11f ("ptrace: ensure arch_ptrace/ptrace_request can never race with SIGKILL")
Link: http://lkml.kernel.org/r/xm26y3vfhmkp.fsf_-_@bsegall-linux.mtv.corp.google.com
Signed-off-by: Ben Segall <bsegall@google.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When __{start,end}_ro_after_init is referenced from C code, we run into
the following build errors on blackfin:
kernel/extable.c:169: undefined reference to `__start_ro_after_init'
kernel/extable.c:169: undefined reference to `__end_ro_after_init'
The build error is due to the fact that blackfin is one of the few
arches that prepends an underscore '_' to all symbols defined in C.
Fix this by wrapping __{start,end}_ro_after_init in vmlinux.lds.h with
VMLINUX_SYMBOL(), which adds the necessary prefix for arches that have
HAVE_UNDERSCORE_SYMBOL_PREFIX.
Link: http://lkml.kernel.org/r/1491259387-15869-1-git-send-email-jeyu@redhat.com
Signed-off-by: Jessica Yu <jeyu@redhat.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Eddie Kovsky <ewk@edkovsky.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fixes: 11fb998986a72a ("mm: move most file-based accounting to the node")
Link: http://lkml.kernel.org/r/1490377730.30219.2.camel@beget.ru
Signed-off-by: Alexander Polyakov <apolyakov@beget.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org> [4.8+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
fdinfo for userfault file descriptor reports UFFD_API_FEATURES. Up
until recently, the UFFD_API_FEATURES was defined as 0, therefore
corresponding field in fdinfo always contained zero. Now, with
introduction of several additional features, UFFD_API_FEATURES is not
longer 0 and it seems better to report actual features requested for the
userfaultfd object described by the fdinfo.
First, the applications that were using userfault will still see zero at
the features field in fdinfo. Next, reporting actual features rather
than available features, gives clear indication of what userfault
features are used by an application.
Link: http://lkml.kernel.org/r/1491140181-22121-1-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Reviewed-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Pavel Emelyanov <xemul@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Doug Smythies reports oops with KSM in this backtrace, I've been seeing
the same:
page_vma_mapped_walk+0xe6/0x5b0
page_referenced_one+0x91/0x1a0
rmap_walk_ksm+0x100/0x190
rmap_walk+0x4f/0x60
page_referenced+0x149/0x170
shrink_active_list+0x1c2/0x430
shrink_node_memcg+0x67a/0x7a0
shrink_node+0xe1/0x320
kswapd+0x34b/0x720
Just as observed in commit 4b0ece6fa016 ("mm: migrate: fix
remove_migration_pte() for ksm pages"), you cannot use page->index
calculations on ksm pages.
page_vma_mapped_walk() is relying on __vma_address(), where a ksm page
can lead it off the end of the page table, and into whatever nonsense is
in the next page, ending as an oops inside check_pte()'s pte_page().
KSM tells page_vma_mapped_walk() exactly where to look for the page, it
does not need any page->index calculation: and that's so also for all
the normal and file and anon pages - just not for THPs and their
subpages. Get out early in most cases: instead of a PageKsm test, move
down the earlier not-THP-page test, as suggested by Kirill.
I'm also slightly worried that this loop can stray into other vmas, so
added a vm_end test to prevent surprises; though I have not imagined
anything worse than a very contrived case, in which a page mlocked in
the next vma might be reclaimed because it is not mlocked in this vma.
Fixes: ace71a19cec5 ("mm: introduce page_vma_mapped_walk()")
Link: http://lkml.kernel.org/r/alpine.LSU.2.11.1704031104400.1118@eggly.anvils
Signed-off-by: Hugh Dickins <hughd@google.com>
Reported-by: Doug Smythies <dsmythies@telus.net>
Tested-by: Doug Smythies <dsmythies@telus.net>
Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Without this fix (and another to the userspace component itself
described later), the kernel will be unable to process any OrangeFS
requests after the userspace component is restarted (due to a crash or
at the administrator's behest).
The bug here is that inside orangefs_remount, the orangefs_request_mutex
is locked. When the userspace component restarts while the filesystem
is mounted, it sends a ORANGEFS_DEV_REMOUNT_ALL ioctl to the device,
which causes the kernel to send it a few requests aimed at synchronizing
the state between the two. While this is happening the
orangefs_request_mutex is locked to prevent any other requests going
through.
This is only half of the bugfix. The other half is in the userspace
component which outright ignores(!) requests made before it considers
the filesystem remounted, which is after the ioctl returns. Of course
the ioctl doesn't return until after the userspace component responds to
the request it ignores. The userspace component has been changed to
allow ORANGEFS_VFS_OP_FEATURES regardless of the mount status.
Mike Marshall says:
"I've tested this patch against the fixed userspace part. This patch is
real important, I hope it can make it into 4.11...
Here's what happens when the userspace daemon is restarted, without
the patch:
=============================================
[ INFO: possible recursive locking detected ]
[ 4.10.0-00007-ge98bdb3 #1 Not tainted ]
---------------------------------------------
pvfs2-client-co/29032 is trying to acquire lock:
(orangefs_request_mutex){+.+.+.}, at: service_operation+0x3c7/0x7b0 [orangefs]
but task is already holding lock:
(orangefs_request_mutex){+.+.+.}, at: dispatch_ioctl_command+0x1bf/0x330 [orangefs]
CPU: 0 PID: 29032 Comm: pvfs2-client-co Not tainted 4.10.0-00007-ge98bdb3 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.9.3-1.fc25 04/01/2014
Call Trace:
__lock_acquire+0x7eb/0x1290
lock_acquire+0xe8/0x1d0
mutex_lock_killable_nested+0x6f/0x6e0
service_operation+0x3c7/0x7b0 [orangefs]
orangefs_remount+0xea/0x150 [orangefs]
dispatch_ioctl_command+0x227/0x330 [orangefs]
orangefs_devreq_ioctl+0x29/0x70 [orangefs]
do_vfs_ioctl+0xa3/0x6e0
SyS_ioctl+0x79/0x90"
Signed-off-by: Martin Brandenburg <martin@omnibond.com>
Acked-by: Mike Marshall <hubcap@omnibond.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
To improve scalability, if hardware queues are shared, restart
a single hardware queue in round-robin fashion. Rename
blk_mq_sched_restart_queues() to reflect the new semantics.
Remove blk_mq_sched_mark_restart_queue() because this function
has no callers. Remove flag QUEUE_FLAG_RESTART because this
patch removes the code that uses this flag.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
While running the srp-test software I noticed that request
processing stalls sporadically at the beginning of a test, namely
when mkfs is run against a dm-mpath device. Every time when that
happened the following command was sufficient to resume request
processing:
echo run >/sys/kernel/debug/block/dm-0/state
This patch avoids that such request processing stalls occur. The
test I ran is as follows:
while srp-test/run_tests -d -r 30 -t 02-mq; do :; done
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
If a .queue_rq() function returns BLK_MQ_RQ_QUEUE_BUSY then the block
driver that implements that function is responsible for rerunning the
hardware queue once requests can be queued again successfully.
commit 52d7f1b5c2f3 ("blk-mq: Avoid that requeueing starts stopped
queues") removed the blk_mq_stop_hw_queue() call from scsi_queue_rq()
for the BLK_MQ_RQ_QUEUE_BUSY case. Hence change all calls to functions
that are intended to rerun a busy queue such that these examine all
hardware queues instead of only stopped queues.
Since no other functions than scsi_internal_device_block() and
scsi_internal_device_unblock() should ever stop or restart a SCSI
queue, change the blk_mq_delay_queue() call into a
blk_mq_delay_run_hw_queue() call.
Fixes: commit 52d7f1b5c2f3 ("blk-mq: Avoid that requeueing starts stopped queues")
Fixes: commit 7e79dadce222 ("blk-mq: stop hardware queue in blk_mq_delay_queue()")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Long Li <longli@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Introduce a function that runs a hardware queue unconditionally
after a delay. Note: there is already a function that stops and
restarts a hardware queue after a delay, namely blk_mq_delay_queue().
This function will be used in the next patch in this series.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Long Li <longli@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
I saw some very confusing sysctl output on my system:
# cat /proc/sys/net/core/xfrm_aevent_rseqth
-2
# cat /proc/sys/net/core/xfrm_aevent_etime
-10
# cat /proc/sys/net/ipv4/tcp_notsent_lowat
-4294967295
Because we forget to set the *negp flag in proc_douintvec, so it will
become a garbage value.
Since the value related to proc_douintvec is always an unsigned integer,
so we can set *negp to false explictily to fix this issue.
Fixes: e7d316a02f68 ("sysctl: handle error writing UINT_MAX to u32 fields")
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Cc: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit e7d316a02f68 ("sysctl: handle error writing UINT_MAX to u32
fields") introduced the proc_douintvec helper function, but it forgot to
add the related sanity check when doing register_sysctl_table. So add
it now.
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Cc: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
blk_mq_update_nr_hw_queues() used to remap hardware queues, which is the
behavior that drivers expect. However, commit 4e68a011428a changed
blk_mq_queue_reinit() to not remap queues for the case of CPU
hotplugging, inadvertently making blk_mq_update_nr_hw_queues() not remap
queues as well. This breaks, for example, NBD's multi-connection mode,
leaving the added hardware queues unused. Fix it by making
blk_mq_update_nr_hw_queues() explicitly remap the queues.
Fixes: 4e68a011428a ("blk-mq: don't redistribute hardware queues on a CPU hotplug event")
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
In elevator_switch(), if blk_mq_init_sched() fails, we attempt to fall
back to the original scheduler. However, at this point, we've already
torn down the original scheduler's tags, so this causes a crash. Doing
the fallback like the legacy elevator path is much harder for mq, so fix
it by just falling back to none, instead.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
If a new hardware queue is added at runtime, we don't allocate scheduler
tags for it, leading to a crash. This hooks up the scheduler framework
to blk_mq_{init,exit}_hctx() to make sure everything gets properly
initialized/freed.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Preparation cleanup for the next couple of fixes, push
blk_mq_sched_setup() and e->ops.mq.init_sched() into a helper.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
While dispatching requests, if we fail to get a driver tag, we mark the
hardware queue as waiting for a tag and put the requests on a
hctx->dispatch list to be run later when a driver tag is freed. However,
blk_mq_dispatch_rq_list() may dispatch requests from multiple hardware
queues if using a single-queue scheduler with a multiqueue device. If
blk_mq_get_driver_tag() fails, it doesn't update the hardware queue we
are processing. This means we end up using the hardware queue of the
previous request, which may or may not be the same as that of the
current request. If it isn't, the wrong hardware queue will end up
waiting for a tag, and the requests will be on the wrong dispatch list,
leading to a hang.
The fix is twofold:
1. Make sure we save which hardware queue we were trying to get a
request for in blk_mq_get_driver_tag() regardless of whether it
succeeds or not.
2. Make blk_mq_dispatch_rq_list() take a request_queue instead of a
blk_mq_hw_queue to make it clear that it must handle multiple
hardware queues, since I've already messed this up on a couple of
occasions.
This didn't appear in testing with nvme and mq-deadline because nvme has
more driver tags than the default number of scheduler tags. However,
with the blk_mq_update_nr_hw_queues() fix, it showed up with nbd.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Currently the cifs module breaks the CIFS specs on reconnect as
described in http://msdn.microsoft.com/en-us/library/cc246529.aspx:
"TreeId (4 bytes): Uniquely identifies the tree connect for the
command. This MUST be 0 for the SMB2 TREE_CONNECT Request."
Signed-off-by: Jan-Marek Glogowski <glogow@fbihome.de>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
Tested-by: Aurelien Aptel <aaptel@suse.com>
Signed-off-by: Steve French <smfrench@gmail.com>
CC: Stable <stable@vger.kernel.org>
|
|
I saw the following build error during a randconfig build:
fs/cifs/smb2ops.c: In function 'smb2_new_lease_key':
fs/cifs/smb2ops.c:1104:2: error: implicit declaration of function 'generate_random_uuid' [-Werror=implicit-function-declaration]
Explicit include the right header to fix this issue.
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
Signed-off-by: Steve French <smfrench@gmail.com>
|
|
The earlier changes to copy range for cifs unintentionally disabled the more
common form of server side copy.
The patch introduces the file_operations helper cifs_copy_file_range()
which is used by the syscall copy_file_range. The new file operations
helper allows us to perform server side copies for SMB2.0 and 2.1
servers as well as SMB 3.0+ servers which do not support the ioctl
FSCTL_DUPLICATE_EXTENTS_TO_FILE.
The new helper uses the ioctl FSCTL_SRV_COPYCHUNK_WRITE to perform
server side copies. The helper is called by vfs_copy_file_range() only
once an attempt to clone the file using the ioctl
FSCTL_DUPLICATE_EXTENTS_TO_FILE has failed.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Steve French <smfrench@gmail.com>
|
|
Server side copy is one of the most important mechanisms smb2/smb3
supports and it was unintentionally disabled for most use cases.
Renaming calls to reflect the underlying smb2 ioctl called. This is
similar to the name duplicate_extents used for a similar ioctl which is
also used to duplicate files by reusing fs blocks. The name change is to
avoid confusion.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Steve French <smfrench@gmail.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
|
|
A signal can interrupt a SendReceive call which result in incoming
responses to the call being ignored. This is a problem for calls such as
open which results in the successful response being ignored. This
results in an open file resource on the server.
The patch looks into responses which were cancelled after being sent and
in case of successful open closes the open fids.
For this patch, the check is only done in SendReceive2()
RH-bz: 1403319
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Cc: Stable <stable@vger.kernel.org>
|
|
The use of the contiguous bit by our hugetlb implementation violates
the break-before-make requirements of the architecture and can lead to
silent data corruption or TLB conflict aborts. Once again, disable these
hugetlb sizes whilst it gets worked out.
This reverts commit ab2e1b89230fa80328262c91d2d0a539a2790d6f.
Conflicts:
arch/arm64/mm/hugetlbpage.c
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
In crc32c_vpmsum() we call enable_kernel_altivec() without first
disabling preemption, which is not allowed:
WARNING: CPU: 9 PID: 2949 at ../arch/powerpc/kernel/process.c:277 enable_kernel_altivec+0x100/0x120
Modules linked in: dm_thin_pool dm_persistent_data dm_bio_prison dm_bufio libcrc32c vmx_crypto ...
CPU: 9 PID: 2949 Comm: docker Not tainted 4.11.0-rc5-compiler_gcc-6.3.1-00033-g308ac7563944 #381
...
NIP [c00000000001e320] enable_kernel_altivec+0x100/0x120
LR [d000000003df0910] crc32c_vpmsum+0x108/0x150 [crc32c_vpmsum]
Call Trace:
0xc138fd09 (unreliable)
crc32c_vpmsum+0x108/0x150 [crc32c_vpmsum]
crc32c_vpmsum_update+0x3c/0x60 [crc32c_vpmsum]
crypto_shash_update+0x88/0x1c0
crc32c+0x64/0x90 [libcrc32c]
dm_bm_checksum+0x48/0x80 [dm_persistent_data]
sb_check+0x84/0x120 [dm_thin_pool]
dm_bm_validate_buffer.isra.0+0xc0/0x1b0 [dm_persistent_data]
dm_bm_read_lock+0x80/0xf0 [dm_persistent_data]
__create_persistent_data_objects+0x16c/0x810 [dm_thin_pool]
dm_pool_metadata_open+0xb0/0x1a0 [dm_thin_pool]
pool_ctr+0x4cc/0xb60 [dm_thin_pool]
dm_table_add_target+0x16c/0x3c0
table_load+0x184/0x400
ctl_ioctl+0x2f0/0x560
dm_ctl_ioctl+0x38/0x50
do_vfs_ioctl+0xd8/0x920
SyS_ioctl+0x68/0xc0
system_call+0x38/0xfc
It used to be sufficient just to call pagefault_disable(), because that
also disabled preemption. But the two were decoupled in commit 8222dbe21e79
("sched/preempt, mm/fault: Decouple preemption from the page fault
logic") in mid 2015.
So add the missing preempt_disable/enable(). We should also call
disable_kernel_fp(), although it does nothing by default, there is a
debug switch to make it active and all enables should be paired with
disables.
Fixes: 6dd7a82cc54e ("crypto: powerpc - Add POWER8 optimised crc32c")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Add junction temperature monitoring supervisor device driver, compatible
with the DA9062 and DA9061 PMICs. A MODULE_DEVICE_TABLE() macro is added.
If the PMIC's internal junction temperature rises above T_WARN (125 degC)
an interrupt is issued. This T_WARN level is defined as the
THERMAL_TRIP_HOT trip-wire inside the device driver.
The thermal triggering mechanism is interrupt based and happens when the
temperature rises above a given threshold level. The component cannot
return an exact temperature, it only has knowledge if the temperature is
above or below a given threshold value. A status bit must be polled to
detect when the temperature falls below that threshold level again. A
kernel work queue is configured to repeatedly poll and detect when the
temperature falls below this trip-wire, between 1 and 10 second intervals
(defaulting at 3 seconds).
This scheme is provided as an example. It would be expected that any
final implementation will also include a notify() function and any of these
settings could be altered to match the application where appropriate.
When over-temperature is reached, the interrupt from the DA9061/2 will be
repeatedly triggered. The IRQ is therefore disabled when the first
over-temperature event happens and the status bit is polled using a
work-queue until it becomes false.
This strategy is designed to allow the periodic transmission of uevents
(HOT trip point) as the first level of temperature supervision method. It
is intended for non-invasive temperature control, where the necessary
measures for cooling the system down are left to the host software. Once
the temperature falls again, the IRQ is re-enabled so a new critical
over-temperature event can be detected.
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
Keerthy
Brian Bian
Lukasz Luba
Dawei Chien
Rafał Miłecki
Linus Torvalds
Chris Salls
Liping Zhang
Tejun Heo
NeilBrown
Johan Hovold
Shuxiao Zhang
Michal Hocko
Jeffy Chen
David Rientjes
Ross Zwisler
bsegall@google.com
Jessica Yu
Alexander Polakov
Mike Rapoport
Hugh Dickins
Martin Brandenburg
Bart Van Assche
Omar Sandoval
Jan-Marek Glogowski
Tobias Regnery
Sachin Prabhu
Will Deacon
Michael Ellerman
Steve Twiss