| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In gsi_irq_setup(), two registers are written with the intention of
disabling inter-EE channel and event IRQs.
But the wrong registers are used (and defined); the ones used are
read-only registers that indicate whether the interrupt condition is
present.
Define the mask registers instead of the status registers, and use
them to disable the inter-EE interrupt types.
Fixes: 46f748ccaf01 ("net: ipa: explicitly disallow inter-EE interrupts")
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20210505223636.232527-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The m_can_start_xmit() function checks if the cdev->tx_skb is NULL and
returns with NETDEV_TX_BUSY in case tx_sbk is not NULL.
There is a race condition in the m_can_tx_work_queue(), where first
the skb is send to the driver and then the case tx_sbk is set to NULL.
A TX complete IRQ might come in between and wake the queue, which
results in tx_skb not being cleared yet.
Fixes: f524f829b75a ("can: m_can: Create a m_can platform framework")
Tested-by: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Since 8ce8c0abcba3 the driver queues work via priv->restart_work when
resuming after suspend, even when the interface was not previously
enabled. This causes a null dereference error as the workqueue is only
allocated and initialized in mcp251x_open().
To fix this we move the workqueue init to mcp251x_can_probe() as there
is no reason to do it later and repeat it whenever mcp251x_open() is
called.
Fixes: 8ce8c0abcba3 ("can: mcp251x: only reset hardware as required")
Link: https://lore.kernel.org/r/17d5d714-b468-482f-f37a-482e3d6df84e@kontron.de
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[mkl: fix error handling in mcp251x_stop()]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds the missing can_rx_offload_del(), that must be called
if mcp251xfd_register() fails.
Fixes: 55e5b97f003e ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Link: https://lore.kernel.org/r/20210504091838.1109047-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When we converted this code to use dev_err_probe() we accidentally
removed a return. It means that if devm_clk_get() it will lead to an
Oops when we call clk_get_rate() on the next line.
Fixes: cf8ee6de2543 ("can: mcp251xfd: mcp251xfd_probe(): use dev_err_probe() to simplify error handling")
Link: https://lore.kernel.org/r/YJANZf13Qxd5Mhr1@mwanda
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
syzbot is able to setup kTLS on an SMC socket which coincidentally
uses sk_user_data too. Later, kTLS treats it as psock so triggers a
refcnt warning. The root cause is that smc_setsockopt() simply calls
TCP setsockopt() which includes TCP_ULP. I do not think it makes
sense to setup kTLS on top of SMC sockets, so we should just disallow
this setup.
It is hard to find a commit to blame, but we can apply this patch
since the beginning of TCP_ULP.
Reported-and-tested-by: syzbot+b54a1ce86ba4a623b7f0@syzkaller.appspotmail.com
Fixes: 734942cc4ea6 ("tcp: ULP infrastructure")
Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Android userspace has been using TCA_KIND with a char[IFNAMESIZ]
many-null-terminated buffer containing the string 'bpf'.
This works on 4.19 and ceases to work on 5.10.
I'm not entirely sure what fixes tag to use, but I think the issue
was likely introduced in the below mentioned 5.4 commit.
Reported-by: Nucca Chen <nuccachen@google.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Fixes: 62794fc4fbf5 ("net_sched: add max len check for TCA_KIND")
Change-Id: I66dc281f165a2858fc29a44869a270a2d698a82b
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An sk_buff is allocated to send a flow control message, but it's not
sent in all cases: in case the state is not appropiate to send it or if
it can't be enqueued.
In the first of these 2 cases, the sk_buff was discarded but not freed,
producing a memory leak.
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Spelling error "eleminate" amended to "eliminate".
Signed-off-by: Sean Gloumeau <sajgloumeau@gmail.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When dumping the ethtool information from all the interfaces, the
netlink reply should contain the NLM_F_MULTI flag. This flag allows
userspace tools to identify that multiple messages are expected.
Link: https://bugzilla.redhat.com/1953847
Fixes: 365f9ae4ee36 ("ethtool: fix genlmsg_put() failure handling in ethnl_default_dumpit()")
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In promiscuous mode Receive All bit is set in GMAC packet filter register,
but outside promiscuous mode Receive All bit is not cleared,
which resulted in all network packets are received when toggle (ON/OFF)
the promiscuous mode.
Fixes: e0f9956a3862 ("net: stmmac: Add option for VLAN filter fail queue enable")
Signed-off-by: Ramesh Babu B <ramesh.babu.b@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commits 8a4cd82d ("nfc: fix refcount leak in llcp_sock_connect()")
and c33b1cc62 ("nfc: fix refcount leak in llcp_sock_bind()")
fixed a refcount leak bug in bind/connect but introduced a
use-after-free if the same local is assigned to 2 different sockets.
This can be triggered by the following simple program:
int sock1 = socket( AF_NFC, SOCK_STREAM, NFC_SOCKPROTO_LLCP );
int sock2 = socket( AF_NFC, SOCK_STREAM, NFC_SOCKPROTO_LLCP );
memset( &addr, 0, sizeof(struct sockaddr_nfc_llcp) );
addr.sa_family = AF_NFC;
addr.nfc_protocol = NFC_PROTO_NFC_DEP;
bind( sock1, (struct sockaddr*) &addr, sizeof(struct sockaddr_nfc_llcp) )
bind( sock2, (struct sockaddr*) &addr, sizeof(struct sockaddr_nfc_llcp) )
close(sock1);
close(sock2);
Fix this by assigning NULL to llcp_sock->local after calling
nfc_llcp_local_put.
This addresses CVE-2021-23134.
Reported-by: Or Cohen <orcohen@paloaltonetworks.com>
Reported-by: Nadav Markus <nmarkus@paloaltonetworks.com>
Fixes: c33b1cc62 ("nfc: fix refcount leak in llcp_sock_bind()")
Signed-off-by: Or Cohen <orcohen@paloaltonetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tcp_set_default_congestion_control() is netns-safe in that it writes
to &net->ipv4.tcp_congestion_control, but it also sets
ca->flags |= TCP_CONG_NON_RESTRICTED which is not namespaced.
This has the unintended side-effect of changing the global
net.ipv4.tcp_allowed_congestion_control sysctl, despite the fact that it
is read-only: 97684f0970f6 ("net: Make tcp_allowed_congestion_control
readonly in non-init netns")
Resolve this netns "leak" by only allowing the init netns to set the
default algorithm to one that is restricted. This restriction could be
removed if tcp_allowed_congestion_control were namespace-ified in the
future.
This bug was uncovered with
https://github.com/JonathonReinhart/linux-netns-sysctl-verify
Fixes: 6670e1524477 ("tcp: Namespace-ify sysctl_tcp_default_congestion_control")
Signed-off-by: Jonathon Reinhart <jonathon.reinhart@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When desc->len is equal to chunk_size, it is legal. But when the
xp_aligned_validate_desc() got chunk_end from desc->addr + desc->len
pointing to the next chunk during the check, it caused the check to
fail.
This problem was first introduced in bbff2f321a86 ("xsk: new descriptor
addressing scheme"). Later in 2b43470add8c ("xsk: Introduce AF_XDP buffer
allocation API") this piece of code was moved into the new function called
xp_aligned_validate_desc(). This function was then moved into xsk_queue.h
via 26062b185eee ("xsk: Explicitly inline functions and move definitions").
Fixes: bbff2f321a86 ("xsk: new descriptor addressing scheme")
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Link: https://lore.kernel.org/bpf/20210428094424.54435-1-xuanzhuo@linux.alibaba.com
|
|
Add documentation for /sys/class/net/<iface>/qmi/pass_through
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 1b479fb80160
("drivers/net/wan/hdlc_fr: Fix a double free in pvc_xmit").
1. This commit is incorrect. "__skb_pad" will NOT free the skb on
failure when its "free_on_error" parameter is "false".
2. This commit claims to fix my commit. But it didn't CC me??
Fixes: 1b479fb80160 ("drivers/net/wan/hdlc_fr: Fix a double free in pvc_xmit")
Cc: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As Or Cohen described:
If sctp_destroy_sock is called without sock_net(sk)->sctp.addr_wq_lock
held and sp->do_auto_asconf is true, then an element is removed
from the auto_asconf_splist without any proper locking.
This can happen in the following functions:
1. In sctp_accept, if sctp_sock_migrate fails.
2. In inet_create or inet6_create, if there is a bpf program
attached to BPF_CGROUP_INET_SOCK_CREATE which denies
creation of the sctp socket.
This patch is to fix it by moving the auto_asconf init out of
sctp_init_sock(), by which inet_create()/inet6_create() won't
need to operate it in sctp_destroy_sock() when calling
sk_common_release().
It also makes more sense to do auto_asconf init while binding the
first addr, as auto_asconf actually requires an ANY addr bind,
see it in sctp_addr_wq_timeout_handler().
This addresses CVE-2021-23133.
Fixes: 610236587600 ("bpf: Add new cgroup attach type to enable sock modifications")
Reported-by: Or Cohen <orcohen@paloaltonetworks.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit b166a20b07382b8bc1dcee2a448715c9c2c81b5b.
This one has to be reverted as it introduced a dead lock, as
syzbot reported:
CPU0 CPU1
---- ----
lock(&net->sctp.addr_wq_lock);
lock(slock-AF_INET6);
lock(&net->sctp.addr_wq_lock);
lock(slock-AF_INET6);
CPU0 is the thread of sctp_addr_wq_timeout_handler(), and CPU1
is that of sctp_close().
The original issue this commit fixed will be fixed in the next
patch.
Reported-by: syzbot+959223586843e69a2674@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check at start of fill_frame_info that the MAC header in the supplied
skb is large enough to fit a struct hsr_ethhdr, as otherwise this is
not a valid HSR frame. If it is too small, return an error which will
then cause the callers to clean up the skb. Fixes a KMSAN-found
uninit-value bug reported by syzbot at:
https://syzkaller.appspot.com/bug?id=f7e9b601f1414f814f7602a82b6619a8d80bce3f
Reported-by: syzbot+e267bed19bfc5478fb33@syzkaller.appspotmail.com
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Normally SCTP_MIB_CURRESTAB is always incremented once asoc enter into
ESTABLISHED from the state < ESTABLISHED and decremented when the asoc
is being deleted.
However, in sctp_sf_do_dupcook_b(), the asoc's state can be changed to
ESTABLISHED from the state >= ESTABLISHED where it shouldn't increment
SCTP_MIB_CURRESTAB. Otherwise, one asoc may increment MIB_CURRESTAB
multiple times but only decrement once at the end.
I was able to reproduce it by using scapy to do the 4-way shakehands,
after that I replayed the COOKIE-ECHO chunk with 'peer_vtag' field
changed to different values, and SCTP_MIB_CURRESTAB was incremented
multiple times and never went back to 0 even when the asoc was freed.
This patch is to fix it by only incrementing SCTP_MIB_CURRESTAB when
the state < ESTABLISHED in sctp_sf_do_dupcook_b().
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 12dfd78e3a74825e6f0bc8df7ef9f938fbc6bfe3.
This can be reverted as shutdown and cookie_ack chunk are using the
same asoc since commit 35b4f24415c8 ("sctp: do asoc update earlier
in sctp_sf_do_dupcook_a").
Reported-by: Jere Leppänen <jere.leppanen@nokia.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 7e9269a5acec6d841d22e12770a0b02db4f5d8f2.
As Jere notice, commit 35b4f24415c8 ("sctp: do asoc update earlier
in sctp_sf_do_dupcook_a") only keeps the SHUTDOWN and COOKIE-ACK
with the same asoc, not transport. So we have to bring this patch
back.
Reported-by: Jere Leppänen <jere.leppanen@nokia.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In enic_hard_start_xmit, it calls enic_queue_wq_skb(). Inside
enic_queue_wq_skb, if some error happens, the skb will be freed
by dev_kfree_skb(skb). But the freed skb is still used in
skb_tx_timestamp(skb).
My patch makes enic_queue_wq_skb() return error and goto spin_unlock()
incase of error. The solution is provided by Govind.
See https://lkml.org/lkml/2021/4/30/961.
Fixes: fb7516d42478e ("enic: add sw timestamp support")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Acked-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One of our benchmarks running in (Google-internal) CI pushes data
through the ringbuf faster htan than userspace is able to consume
it. In this case it seems we're actually able to get >INT_MAX entries
in a single ring_buffer__consume() call. ASAN detected that cnt
overflows in this case.
Fix by using 64-bit counter internally and then capping the result to
INT_MAX before converting to the int return type. Do the same for
the ring_buffer__poll().
Fixes: bf99c936f947 (libbpf: Add BPF ring buffer support)
Signed-off-by: Brendan Jackman <jackmanb@google.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210429130510.1621665-1-jackmanb@google.com
|
|
The current implemented mechanisms to mitigate data disclosure under
speculation mainly address stack and map value oob access from the
speculative domain. However, Piotr discovered that uninitialized BPF
stack is not protected yet, and thus old data from the kernel stack,
potentially including addresses of kernel structures, could still be
extracted from that 512 bytes large window. The BPF stack is special
compared to map values since it's not zero initialized for every
program invocation, whereas map values /are/ zero initialized upon
their initial allocation and thus cannot leak any prior data in either
domain. In the non-speculative domain, the verifier ensures that every
stack slot read must have a prior stack slot write by the BPF program
to avoid such data leaking issue.
However, this is not enough: for example, when the pointer arithmetic
operation moves the stack pointer from the last valid stack offset to
the first valid offset, the sanitation logic allows for any intermediate
offsets during speculative execution, which could then be used to
extract any restricted stack content via side-channel.
Given for unprivileged stack pointer arithmetic the use of unknown
but bounded scalars is generally forbidden, we can simply turn the
register-based arithmetic operation into an immediate-based arithmetic
operation without the need for masking. This also gives the benefit
of reducing the needed instructions for the operation. Given after
the work in 7fedb63a8307 ("bpf: Tighten speculative pointer arithmetic
mask"), the aux->alu_limit already holds the final immediate value for
the offset register with the known scalar. Thus, a simple mov of the
immediate to AX register with using AX as the source for the original
instruction is sufficient and possible now in this case.
Reported-by: Piotr Krysiuk <piotras@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Piotr Krysiuk <piotras@gmail.com>
Reviewed-by: Piotr Krysiuk <piotras@gmail.com>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
|
|
The negation logic for the case where the off_reg is sitting in the
dst register is not correct given then we cannot just invert the add
to a sub or vice versa. As a fix, perform the final bitwise and-op
unconditionally into AX from the off_reg, then move the pointer from
the src to dst and finally use AX as the source for the original
pointer arithmetic operation such that the inversion yields a correct
result. The single non-AX mov in between is possible given constant
blinding is retaining it as it's not an immediate based operation.
Fixes: 979d63d50c0c ("bpf: prevent out of bounds speculation on pointer arithmetic")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Piotr Krysiuk <piotras@gmail.com>
Reviewed-by: Piotr Krysiuk <piotras@gmail.com>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
|
|
In commit f4da56529da60 ("net: stmmac: Add support for external
trigger timestamping"), struct stmmac_priv was declared at line 507
which caused duplicate struct declarations.
Remove later duplicate declaration here.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Reviewed-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A number of PHYs support the PHY tunable to set and get
downshift. However, only 88E1116R enables downshift by default. Extend
this default enabled to all the PHYs that support the downshift
tunable.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The same thing should be done for sctp_sf_do_dupcook_b().
Meanwhile, SCTP_CMD_UPDATE_ASSOC cmd can be removed.
v1->v2:
- Fix the return value in sctp_sf_do_assoc_update().
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This can be reverted as shutdown and cookie_ack chunk are using the
same asoc since the last patch.
This reverts commit 145cb2f7177d94bc54563ed26027e952ee0ae03c.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There's a panic that occurs in a few of envs, the call trace is as below:
[] general protection fault, ... 0x29acd70f1000a: 0000 [#1] SMP PTI
[] RIP: 0010:sctp_ulpevent_notify_peer_addr_change+0x4b/0x1fa [sctp]
[] sctp_assoc_control_transport+0x1b9/0x210 [sctp]
[] sctp_do_8_2_transport_strike.isra.16+0x15c/0x220 [sctp]
[] sctp_cmd_interpreter.isra.21+0x1231/0x1a10 [sctp]
[] sctp_do_sm+0xc3/0x2a0 [sctp]
[] sctp_generate_timeout_event+0x81/0xf0 [sctp]
This is caused by a transport use-after-free issue. When processing a
duplicate COOKIE-ECHO chunk in sctp_sf_do_dupcook_a(), both COOKIE-ACK
and SHUTDOWN chunks are allocated with the transort from the new asoc.
However, later in the sideeffect machine, the old asoc is used to send
them out and old asoc's shutdown_last_sent_to is set to the transport
that SHUTDOWN chunk attached to in sctp_cmd_setup_t2(), which actually
belongs to the new asoc. After the new_asoc is freed and the old asoc
T2 timeout, the old asoc's shutdown_last_sent_to that is already freed
would be accessed in sctp_sf_t2_timer_expire().
Thanks Alexander and Jere for helping dig into this issue.
To fix it, this patch is to do the asoc update first, then allocate
the COOKIE-ACK and SHUTDOWN chunks with the 'updated' old asoc. This
would make more sense, as a chunk from an asoc shouldn't be sent out
with another asoc. We had fixed quite a few issues caused by this.
Fixes: 145cb2f7177d ("sctp: Fix bundling of SHUTDOWN with COOKIE-ACK")
Reported-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Reported-by: syzbot+bbe538efd1046586f587@syzkaller.appspotmail.com
Reported-by: Michal Tesar <mtesar@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add Marc Dionne as a co-maintainer for kafs and rxrpc.
Signed-off-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove it from the MODULE_AUTHOR statements referencing it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Variable 'err' is set to zero but this value is never read as it is
overwritten with a new value later on, hence it is a redundant
assignment and can be removed.
Clean up the following clang-analyzer warning:
net/vmw_vsock/vmci_transport.c:948:2: warning: Value stored to 'err' is
never read [clang-analyzer-deadcode.DeadStores]
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If selftest and reset are performed at the same time, the phy
loopback setting may be still in enable state after the reset,
and device cannot link up. So fix this issue by disabling phy
loopback before phy_start().
Fixes: 256727da7395 ("net: hns3: Add MDIO support to HNS3 Ethernet driver for hip08 SoC")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HW error and global reset are reported through MSIX interrupts.
The same error may be reported to different functions at the
same time. When global reset begins, the pending reset request
set by this error is unnecessary. So clear the pending reset
request after the reset is complete to avoid the repeated reset.
Fixes: f6162d44126c ("net: hns3: add handling of hw errors reported through MSIX")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, netif_tx_stop_all_queues() is used to ensure that
the xmit is not running, but for the concurrent case it will
not take effect, since netif_tx_stop_all_queues() just sets
a flag without locking to indicate that the xmit queue(s)
should not be run.
So use netif_tx_disable() to replace netif_tx_stop_all_queues(),
it takes the xmit queue lock while marking the queue stopped.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When skb->ip_summed is CHECKSUM_PARTIAL, for non-tunnel udp packet,
which has a dest port as the IANA assigned, the hardware is expected
to do the checksum offload, but the hardware whose version is below
V3 will not do the checksum offload when udp dest port is 4790.
So fixes it by doing the checksum in software for this case.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An issue found when network interface is down and up again, FPE handshake
fails to trigger. This is due to __FPE_REMOVING bit remains being set in
stmmac_fpe_stop_wq() but not cleared in stmmac_fpe_start_wq(). This
cause FPE workqueue task, stmmac_fpe_lp_task() not able to be executed.
To fix this, add clearing __FPE_REMOVING bit in stmmac_fpe_start_wq().
Fixes: 5a5586112b92 ("net: stmmac: support FPE link partner hand-shaking procedure")
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The BPF program for the snprintf selftest runs on all syscall entries.
On busy multicore systems this can cause concurrency issues.
For example it was observed that sometimes the userspace part of the
test reads " 4 0000" instead of " 4 000" (extra '0' at the end)
which seems to happen just before snprintf on another core sets
end[-1] = '\0'.
This patch adds a pid filter to the test to ensure that no
bpf_snprintf() will write over the test's output buffers while the
userspace reads the values.
Fixes: c2e39c6bdc7e ("selftests/bpf: Add a series of tests for bpf_snprintf")
Reported-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Florent Revest <revest@chromium.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210428152501.1024509-1-revest@chromium.org
|
|
ksz_switch_alloc() will return NULL only if allocation is failed. So,
the proper return value is -ENOMEM.
Fixes: 60a364760002 ("net: dsa: microchip: Add Microchip KSZ8863 SMI based driver support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix possible NULL pointer dereference in case devm_kzalloc() failed to
allocate memory
Fixes: cc13e52c3a89 ("net: dsa: microchip: Add Microchip KSZ8863 SPI based driver support")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix possible NULL pointer dereference in case devm_kzalloc() failed to
allocate memory.
Fixes: 60a364760002 ("net: dsa: microchip: Add Microchip KSZ8863 SMI based driver support")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Variable 'err' is set to -EIO but this value is never read as it is
overwritten with a new value later on, hence it is a redundant
assignment and can be removed.
Clean up the following clang-analyzer warning:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.c:1195:2: warning: Value
stored to 'err' is never read [clang-analyzer-deadcode.DeadStores]
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Variable queue is set to bp->queues but these values is not used as it
is overwritten later on, hence redundant assignment can be removed.
Cleans up the following clang-analyzer warning:
drivers/net/ethernet/cadence/macb_main.c:4919:21: warning: Value stored
to 'queue' during its initialization is never read
[clang-analyzer-deadcode.DeadStores].
drivers/net/ethernet/cadence/macb_main.c:4832:21: warning: Value stored
to 'queue' during its initialization is never read
[clang-analyzer-deadcode.DeadStores].
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
His email bounces with permanent error "550 Invalid recipient". His last
email was from 2020-09-09 on the LKML and he seems to have left TI.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
His email bounces with permanent error "550 Invalid recipient". His last
email on the LKML was from 2015-10-22 on the LKML.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In some cases, the device is not initialized because reset failed.
If another task calls hns3_reset_notify_up_enet() before reset
retry, it will cause an error since uninitialized pointer access.
So add check for HNS3_NIC_STATE_INITED before calling
hns3_nic_net_open() in hns3_reset_notify_up_enet().
Fixes: bb6b94a896d4 ("net: hns3: Add reset interface implementation in client")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The message sent to VF should be initialized, otherwise random
value of some contents may cause improper processing by the target.
So add a initialization to message in hclge_get_link_mode().
Fixes: 9194d18b0577 ("net: hns3: fix the problem that the supported port is empty")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to the UM, the type and enable status of igu_egu_hw_err
should be configured separately. Currently, the type field is
incorrect when disable this error. So fix it by configuring these
two fields separately.
Fixes: bf1faf9415dd ("net: hns3: Add enable and process hw errors from IGU, EGU and NCSI")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Alex Elder
Marc Kleine-Budde
Frieder Schrempf
Dan Carpenter
Cong Wang
Maciej Żenczykowski
Íñigo Huguet
Sean Gloumeau
Fernando Fernandez Mancera
Ramesh Babu B
Or Cohen
Jonathon Reinhart
Xuan Zhuo
Daniele Palmas
Xie He
Xin Long
Phillip Potter
Lv Yunlong
Brendan Jackman
Daniel Borkmann
Wan Jiabing
Maxim Kochetkov
Marc Dionne
Johannes Berg
Yang Li
Yufeng Mo
Peng Li
Hao Chen
Mohammad Athari Bin Ismail
Florent Revest
Oleksij Rempel
Jiapeng Chong
Michael Walle
Jian Shen