| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
We have dts property for "ti,sysc-delay-us", and we're using it, but the
wait after OCP softreset only happens if devices are probed in legacy mode.
Let's add a delay after writing the OCP softreset when specified.
Fixes: e0db94fe87da ("bus: ti-sysc: Make OCP reset work for sysstatus and sysconfig reset bits")
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The imx_soc_device_init functions tries to fetch the ocotp regmap in
order to soc serial number. If regmap fetch fails then a message is
printed but regmap_read is called anyway and the system crashes.
Failing to lookup ocotp regmap shouldn't be a fatal boot error so check
that the pointer is valid.
Only side-effect of ocotp lookup failure now is that serial number will
be reported as all-zeros which is acceptable.
Cc: stable@vger.kernel.org
Fixes: 8267ff89b713 ("ARM: imx: Add serial number support for i.MX6/7 SoCs")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Tested-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This is currently off and that's not desirable: default imx config is
meant to be generally useful for development and debugging.
Running git bisect between v5.4 and v5.5-rc1 finds this started from
commit 0e4a459f56c3 ("tracing: Remove unnecessary DEBUG_FS dependency")
Explicit CONFIG_DEBUG_FS=y was earlier removed by
commit c29d541f590c ("ARM: imx_v6_v7_defconfig: Remove unneeded options")
A very similar fix was required before:
commit 7e9eb6268809 ("ARM: imx_v6_v7_defconfig: Explicitly restore CONFIG_DEBUG_FS")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Many peripherals are affected by gpio5/2, not just sensors. One of those
is ethernet phy so network boot is current broken.
Fix by renaming reg_sensors and marking it as "always on". Also add a
comment asking for careful testing if this is to be made dynamic in the
future.
The "peri_3v3" naming is similar to imx6sx-sdb and regulator-name is
same string as in schematics (VPERI_3V3).
Fixes: 09e2b1048954 ("ARM: dts: imx6ul-14x14-evk: Add sensors' GPIO regulator")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The reboot register isn't located inside the DCFG controller, but in its
own RST controller. Fix it.
Fixes: 8897f3255c9c ("arm64: dts: Add support for NXP LS1028A SoC")
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The file was moved, causing a build error:
In file included from /git/arm-soc/arch/arm/mach-mmp/pxa168.c:28:
arch/arm/mach-mmp/pxa168.h:22:10: fatal error: cputype.h: No such file or directory
Include it from the new location.
Link: https://lore.kernel.org/r/20191210203409.2875880-1-arnd@arndb.de
Fixes: 32adcaa010fa ("ARM: mmp: move cputype.h to include/linux/soc/")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The LCD panel on AM4 GP EVMs and ePOS boards seems to be
osd070t1718-19ts. The current dts files say osd057T0559-34ts. Possibly
the panel has changed since the early EVMs, or there has been a mistake
with the panel type.
Update the DT files accordingly.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The temperature sensor may jump backwards because there is a wrong
calibration value. Both values have to be monotonically increasing.
Fix it.
This was tested on a custom board.
Fixes: 571cebfe8e2b ("arm64: dts: ls1028a: Add Thermal Monitor Unit node")
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
After the commit 8267ff89b713 ("ARM: imx: Add serial number support for i.MX6/7 SoCs")
the kernel doesn't start on i.MX6ULL/ULZ SoC.
Tested on next-20191205.
For i.MX6ULL/ULZ the variable "ocotp_compat" is set to "fsl,imx6ul-ocotp", but with commit
ffbc34bf0e9c ("nvmem: imx-ocotp: Implement i.MX6ULL/ULZ support") and commit
f243bc821ee3 ("ARM: dts: imx6ull: Fix i.MX6ULL/ULZ ocotp compatible") the value
"fsl,imx6ull-ocotp" is already defined and set in device tree...
By setting "ocotp_compat" to "fsl,imx6ull-ocotp" the kernel does boot.
Fixes: 8267ff89b713 ("ARM: imx: Add serial number support for i.MX6/7 SoCs")
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
During definition of the CPU thermal zone of BCM283x SoC family there
was a misunderstanding of the meaning "criticial trip point" and the
thermal throttling range of the VideoCore firmware. The latter one takes
effect when the core temperature is at least 85 degree celsius or higher
So the current critical trip point doesn't make sense, because the
thermal shutdown appears before the firmware has a chance to throttle
the ARM core(s).
Fix these unwanted shutdowns by increasing the critical trip point
to a value which shouldn't be reached with working thermal throttling.
Fixes: 0fe4d2181cc4 ("ARM: dts: bcm283x: Add CPU thermal zone with 1 trip point")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Commit 0e4a459f56c3 ("tracing: Remove unnecessary DEBUG_FS dependency")
removed select for DEBUG_FS but we still need it at least for enabling
deeper idle states for the SoCs.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The TI_CPSW_SWITCHDEV definition in Kconfig was changed from "select
NET_SWITCHDEV" to "depends on NET_SWITCHDEV", and therefore it is required
to explicitelly enable NET_SWITCHDEV config option in omap2plus_defconfig.
Fixes: 3727d259ddaf ("arm: omap2plus_defconfig: enable new cpsw switchdev driver")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The phy mode should be rgmii-id. For some reason, it used to work with
rgmii-txid but doesn't any more.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 03856e928b0e ("bus: ti-sysc: Handle mstandby quirk and use it for
musb") added quirk handling for mstandby quirk but did not consider that
we also need a quirk variant for SYSC_QUIRK_FORCE_MSTANDBY.
We need to use forced idle mode for both SYSC_QUIRK_SWSUP_MSTANDBY and
SYSC_QUIRK_FORCE_MSTANDBY, but SYSC_QUIRK_SWSUP_MSTANDBY also need to
additionally also configure no-idle mode when enabled.
Fixes: 03856e928b0e ("bus: ti-sysc: Handle mstandby quirk and use it for musb")
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
When an optional reset is not present, __devm_reset_control_get() and
devm_reset_control_array_get() still register resource data to release
the non-existing reset on cleanup, which is futile.
Fix this by skipping NULL reset control pointers.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
of_reset_control_array_get() and devm_reset_control_array_get() return
struct reset_control pointers, not internal struct reset_control_array
pointers, just like all other reset control API calls.
Correct the kerneldoc to match the code.
Fixes: 17c82e206d2a3cd8 ("reset: Add APIs to manage array of resets")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The use of IS_ALIGNED() is incorrect, the typical resource we pass looks
like this: start: 0x8404318, size: 0x30. When using IS_ALIGNED() we will
get the following 0x8404318 & (0x18 - 1) = 0x10 which is definitively
not equal to 0, same goes with the size. These two checks would make the
driver fail probing.
Remove the resource checks, since there should be no constraint on the
base addresse or size.
Fixes: 77750bc089e4 ("reset: Add Broadcom STB SW_INIT reset controller driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The reset controller has a #reset-cells value of 1, so we should see a
phandle plus a register identifier, fix the example.
Fixes: 0807caf647dd ("dt-bindings: reset: Add document for Broadcom STB reset controller")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The MDIO node on Cygnus had an reversed #address-cells and
#size-cells properties, correct those.
Fixes: 40c26d3af60a ("ARM: dts: Cygnus: Add the ethernet switch and ethernet PHY")
Reported-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Raspberry Pi's firmware has a feature to select how much memory to
reserve for its GPU called 'gpu_mem'. The possible values go from 16MB
to 944MB, with a default of 64MB. This memory resides in the topmost
part of the lower 1GB memory area and grows bigger expanding towards the
begging of memory.
It turns out that with low 'gpu_mem' values (16MB and 32MB) the size of
the memory available to the system in the lower 1GB area can outgrow the
interconnect's dma-range as its size was selected based on the maximum
system memory available given the default gpu_mem configuration. This
makes that memory slice unavailable for DMA. And may cause nasty kernel
warnings if CMA happens to include it.
Change soc's dma-ranges to really reflect it's HW limitation, which is
being able to only DMA to the lower 1GB area.
Fixes: 7dbe8c62ceeb ("ARM: dts: Add minimal Raspberry Pi 4 support")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
The MDIO node on BCM5301X had an reversed #address-cells and
#size-cells properties, correct those, silencing checker warnings:
.../linux/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dt.yaml: mdio@18003000: #address-cells:0:0: 1 was expected
Reported-by: Simon Horman <simon.horman@netronome.com>
Fixes: 23f1eca6d59b ("ARM: dts: BCM5301X: Specify MDIO bus in the DT")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Since commit ca74b316df96 ("arm: Use common cpu_topology structure and
functions.") the core cpumask has to be modified during cpu hotplug
operations. So using them to set up cpufreq policy cpumask may be
incorrect as it may contain only cpus that are online at that instance.
Instead, we can use the cpumask setup by OPP library that contains all
the cpus sharing OPP table using dev_pm_opp_get_sharing_cpus.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Currently we add individual copy of same OPP table for each CPU within
the cluster. This is redundant and doesn't reflect the reality.
We can't use core cpumask to set policy->cpus in ve_spc_cpufreq_init()
anymore as it gets called via cpuhp_cpufreq_online()->cpufreq_online()
->cpufreq_driver->init() and the cpumask gets updated upon CPU hotplug
operations. It also may cause issues when the vexpress_spc_cpufreq
driver is built as a module.
Since ve_spc_clk_init is built-in device initcall, we should be able to
use the same topology_core_cpumask to set the opp sharing cpumask via
dev_pm_opp_set_sharing_cpus and use the same later in the driver via
dev_pm_opp_get_sharing_cpus.
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
The power button was only producing irqs, but no key events,
Forced power down with long key press works, so probably
only a short spike arrives at the SoC.
Further investigation shows that LDORTC2 is off after boot
of the vendor kernel. LDORTC2 is shared with a GPIO at the pmic
which probably transfers the button press to the SoC.
That regulator off at boot, so "regulator-boot-on" is definitively
wrong. So remove that.
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Fixes: c100ea86e6ab ("ARM: dts: add Netronix E60K02 board common file")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Without this "jedec,spi-nor" compatible property, probing of the SPI NOR
does not work on the NXP i.MX6ULL EVK. Fix this by adding this
compatible property to the DT.
Fixes: 7d77b8505aa9 ("ARM: dts: imx6ull: fix the imx6ull-14x14-evk configuration")
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
|
|
We had cases in the previous patch where we were sending the security
descriptor context on SMB3 open (file create) in cases when we hadn't
mounted with with "modefromsid" mount option.
Add check for that mount flag before calling ad_sd_context in
open init.
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
|
|
In referenced fix we removed the RTL8168e-specific jumbo config for
RTL8168evl in rtl_hw_jumbo_enable(). We have to do the same in
rtl_hw_jumbo_disable().
v2: fix referenced commit id
Fixes: 14012c9f3bb9 ("r8169: fix jumbo configuration for RTL8168evl")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
pipe_wait() may be simple, but since it relies on the pipe lock, it
means that we have to do the wakeup while holding the lock. That's
unfortunate, because the very first thing the waked entity will want to
do is to get the pipe lock for itself.
So get rid of the pipe_wait() usage by simply releasing the pipe lock,
doing the wakeup (if required) and then using wait_event_interruptible()
to wait on the right condition instead.
wait_event_interruptible() handles races on its own by comparing the
wakeup condition before and after adding itself to the wait queue, so
you can use an optimistic unlocked condition for it.
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Jiasen Lin <linjiasen@hygon.cn>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
This code is ancient, and goes back to when we only had a single page
for the pipe buffers. The exact history is hidden in the mists of time
(ie "before git", and in fact predates the BK repository too).
At that long-ago point in time, it actually helped to try to merge big
back-and-forth pipe reads and writes, and not limit pipe reads to the
single pipe buffer in length just because that was all we had at a time.
However, since then we've expanded the pipe buffers to multiple pages,
and this logic really doesn't seem to make sense. And a lot of it is
somewhat questionable (ie "hmm, the user asked for a non-blocking read,
but we see that there's a writer pending, so let's wait anyway to get
the extra data that the writer will have").
But more importantly, it makes the "go to sleep" logic much less
obvious, and considering the wakeup issues we've had, I want to make for
less of those kinds of things.
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is the read side version of the previous commit: it simplifies the
logic to only wake up waiting writers when necessary, and makes sure to
use a synchronous wakeup. This time not so much for GNU make jobserver
reasons (that pipe never fills up), but simply to get the writer going
quickly again.
A bit less verbose commentary this time, if only because I assume that
the write side commentary isn't going to be ignored if you touch this
code.
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The pipe rework ends up having been extra painful, partly becaused of
actual bugs with ordering and caching of the pipe state, but also
because of subtle performance issues.
In particular, the pipe rework caused the kernel build to inexplicably
slow down.
The reason turns out to be that the GNU make jobserver (which limits the
parallelism of the build) uses a pipe to implement a "token" system: a
parallel submake will read a character from the pipe to get the job
token before starting a new job, and will write a character back to the
pipe when it is done. The overall job limit is thus easily controlled
by just writing the appropriate number of initial token characters into
the pipe.
But to work well, that really means that the old behavior of write
wakeups being synchronous (WF_SYNC) is very important - when the pipe
writer wakes up a reader, we want the reader to actually get scheduled
immediately. Otherwise you lose the parallelism of the build.
The pipe rework lost that synchronous wakeup on write, and we had
clearly all forgotten the reasons and rules for it.
This rewrites the pipe write wakeup logic to do the required Wsync
wakeups, but also clarifies the logic and avoids extraneous wakeups.
It also ends up addign a number of comments about what oit does and why,
so that we hopefully don't end up forgetting about this next time we
change this code.
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use the new tcf_proto_check_kind() helper to make sure user
provided value is well formed.
BUG: KMSAN: uninit-value in string_nocheck lib/vsprintf.c:606 [inline]
BUG: KMSAN: uninit-value in string+0x4be/0x600 lib/vsprintf.c:668
CPU: 0 PID: 12358 Comm: syz-executor.1 Not tainted 5.4.0-rc8-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1c9/0x220 lib/dump_stack.c:118
kmsan_report+0x128/0x220 mm/kmsan/kmsan_report.c:108
__msan_warning+0x64/0xc0 mm/kmsan/kmsan_instr.c:245
string_nocheck lib/vsprintf.c:606 [inline]
string+0x4be/0x600 lib/vsprintf.c:668
vsnprintf+0x218f/0x3210 lib/vsprintf.c:2510
__request_module+0x2b1/0x11c0 kernel/kmod.c:143
tcf_proto_lookup_ops+0x171/0x700 net/sched/cls_api.c:139
tc_chain_tmplt_add net/sched/cls_api.c:2730 [inline]
tc_ctl_chain+0x1904/0x38a0 net/sched/cls_api.c:2850
rtnetlink_rcv_msg+0x115a/0x1580 net/core/rtnetlink.c:5224
netlink_rcv_skb+0x431/0x620 net/netlink/af_netlink.c:2477
rtnetlink_rcv+0x50/0x60 net/core/rtnetlink.c:5242
netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline]
netlink_unicast+0xf3e/0x1020 net/netlink/af_netlink.c:1328
netlink_sendmsg+0x110f/0x1330 net/netlink/af_netlink.c:1917
sock_sendmsg_nosec net/socket.c:637 [inline]
sock_sendmsg net/socket.c:657 [inline]
___sys_sendmsg+0x14ff/0x1590 net/socket.c:2311
__sys_sendmsg net/socket.c:2356 [inline]
__do_sys_sendmsg net/socket.c:2365 [inline]
__se_sys_sendmsg+0x305/0x460 net/socket.c:2363
__x64_sys_sendmsg+0x4a/0x70 net/socket.c:2363
do_syscall_64+0xb6/0x160 arch/x86/entry/common.c:291
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x45a649
Code: ad b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007f0790795c78 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 000000000045a649
RDX: 0000000000000000 RSI: 0000000020000300 RDI: 0000000000000006
RBP: 000000000075bfc8 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f07907966d4
R13: 00000000004c8db5 R14: 00000000004df630 R15: 00000000ffffffff
Uninit was created at:
kmsan_save_stack_with_flags mm/kmsan/kmsan.c:149 [inline]
kmsan_internal_poison_shadow+0x5c/0x110 mm/kmsan/kmsan.c:132
kmsan_slab_alloc+0x97/0x100 mm/kmsan/kmsan_hooks.c:86
slab_alloc_node mm/slub.c:2773 [inline]
__kmalloc_node_track_caller+0xe27/0x11a0 mm/slub.c:4381
__kmalloc_reserve net/core/skbuff.c:141 [inline]
__alloc_skb+0x306/0xa10 net/core/skbuff.c:209
alloc_skb include/linux/skbuff.h:1049 [inline]
netlink_alloc_large_skb net/netlink/af_netlink.c:1174 [inline]
netlink_sendmsg+0x783/0x1330 net/netlink/af_netlink.c:1892
sock_sendmsg_nosec net/socket.c:637 [inline]
sock_sendmsg net/socket.c:657 [inline]
___sys_sendmsg+0x14ff/0x1590 net/socket.c:2311
__sys_sendmsg net/socket.c:2356 [inline]
__do_sys_sendmsg net/socket.c:2365 [inline]
__se_sys_sendmsg+0x305/0x460 net/socket.c:2363
__x64_sys_sendmsg+0x4a/0x70 net/socket.c:2363
do_syscall_64+0xb6/0x160 arch/x86/entry/common.c:291
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: 6f96c3c6904c ("net_sched: fix backward compatibility for TCA_KIND")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RTL8125 also requires to enable RX for WoL.
v2: add missing Fixes tag
Fixes: f1bce4ad2f1c ("r8169: add support for RTL8125")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we receive a new packet from the guest, we check if the
src_cid is correct, but we forgot to check the dst_cid.
The host should accept only packets where dst_cid is
equal to the host CID.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit ef87f7da6b28 ("net: phy: dp83867: move dt parsing to probe")
causes regression on TI dra71x-evm and dra72x-evm, where DP83867 PHY is
used in "rgmii-id" mode - the networking stops working.
Unfortunately, it's not enough to just move DT parsing code to .probe() as
it depends on phydev->interface value, which is set to correct value abter
the .probe() is completed and before calling .config_init(). So, RGMII
configuration can't be loaded from DT.
To fix and issue
- move RGMII validation code to .config_init()
- parse RGMII parameters in dp83867_of_init(), but consider them as
optional.
Fixes: ef87f7da6b28 ("net: phy: dp83867: move dt parsing to probe")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now RX interrupt is triggered twice every time, because in
cpsw_rx_interrupt() it is asked first and then disabled. So there will be
pending interrupt always, when RX interrupt is enabled again in NAPI
handler.
Fix it by first disabling IRQ and then do ask.
Fixes: 870915feabdc ("drivers: net: cpsw: remove disable_irq/enable_irq as irq can be masked from cpsw itself")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzbot was once again able to crash a host by setting a very small mtu
on loopback device.
Let's make inetdev_valid_mtu() available in include/net/ip.h,
and use it in ip_setup_cork(), so that we protect both ip_append_page()
and __ip_append_data()
Also add a READ_ONCE() when the device mtu is read.
Pairs this lockless read with one WRITE_ONCE() in __dev_set_mtu(),
even if other code paths might write over this field.
Add a big comment in include/linux/netdevice.h about dev->mtu
needing READ_ONCE()/WRITE_ONCE() annotations.
Hopefully we will add the missing ones in followup patches.
[1]
refcount_t: saturated; leaking memory.
WARNING: CPU: 0 PID: 9464 at lib/refcount.c:22 refcount_warn_saturate+0x138/0x1f0 lib/refcount.c:22
Kernel panic - not syncing: panic_on_warn set ...
CPU: 0 PID: 9464 Comm: syz-executor850 Not tainted 5.4.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x197/0x210 lib/dump_stack.c:118
panic+0x2e3/0x75c kernel/panic.c:221
__warn.cold+0x2f/0x3e kernel/panic.c:582
report_bug+0x289/0x300 lib/bug.c:195
fixup_bug arch/x86/kernel/traps.c:174 [inline]
fixup_bug arch/x86/kernel/traps.c:169 [inline]
do_error_trap+0x11b/0x200 arch/x86/kernel/traps.c:267
do_invalid_op+0x37/0x50 arch/x86/kernel/traps.c:286
invalid_op+0x23/0x30 arch/x86/entry/entry_64.S:1027
RIP: 0010:refcount_warn_saturate+0x138/0x1f0 lib/refcount.c:22
Code: 06 31 ff 89 de e8 c8 f5 e6 fd 84 db 0f 85 6f ff ff ff e8 7b f4 e6 fd 48 c7 c7 e0 71 4f 88 c6 05 56 a6 a4 06 01 e8 c7 a8 b7 fd <0f> 0b e9 50 ff ff ff e8 5c f4 e6 fd 0f b6 1d 3d a6 a4 06 31 ff 89
RSP: 0018:ffff88809689f550 EFLAGS: 00010286
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffffff815e4336 RDI: ffffed1012d13e9c
RBP: ffff88809689f560 R08: ffff88809c50a3c0 R09: fffffbfff15d31b1
R10: fffffbfff15d31b0 R11: ffffffff8ae98d87 R12: 0000000000000001
R13: 0000000000040100 R14: ffff888099041104 R15: ffff888218d96e40
refcount_add include/linux/refcount.h:193 [inline]
skb_set_owner_w+0x2b6/0x410 net/core/sock.c:1999
sock_wmalloc+0xf1/0x120 net/core/sock.c:2096
ip_append_page+0x7ef/0x1190 net/ipv4/ip_output.c:1383
udp_sendpage+0x1c7/0x480 net/ipv4/udp.c:1276
inet_sendpage+0xdb/0x150 net/ipv4/af_inet.c:821
kernel_sendpage+0x92/0xf0 net/socket.c:3794
sock_sendpage+0x8b/0xc0 net/socket.c:936
pipe_to_sendpage+0x2da/0x3c0 fs/splice.c:458
splice_from_pipe_feed fs/splice.c:512 [inline]
__splice_from_pipe+0x3ee/0x7c0 fs/splice.c:636
splice_from_pipe+0x108/0x170 fs/splice.c:671
generic_splice_sendpage+0x3c/0x50 fs/splice.c:842
do_splice_from fs/splice.c:861 [inline]
direct_splice_actor+0x123/0x190 fs/splice.c:1035
splice_direct_to_actor+0x3b4/0xa30 fs/splice.c:990
do_splice_direct+0x1da/0x2a0 fs/splice.c:1078
do_sendfile+0x597/0xd00 fs/read_write.c:1464
__do_sys_sendfile64 fs/read_write.c:1525 [inline]
__se_sys_sendfile64 fs/read_write.c:1511 [inline]
__x64_sys_sendfile64+0x1dd/0x220 fs/read_write.c:1511
do_syscall_64+0xfa/0x790 arch/x86/entry/common.c:294
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x441409
Code: e8 ac e8 ff ff 48 83 c4 18 c3 0f 1f 80 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 eb 08 fc ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007fffb64c4f78 EFLAGS: 00000246 ORIG_RAX: 0000000000000028
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 0000000000441409
RDX: 0000000000000000 RSI: 0000000000000006 RDI: 0000000000000005
RBP: 0000000000073b8a R08: 0000000000000010 R09: 0000000000000010
R10: 0000000000010001 R11: 0000000000000246 R12: 0000000000402180
R13: 0000000000402210 R14: 0000000000000000 R15: 0000000000000000
Kernel Offset: disabled
Rebooting in 86400 seconds..
Fixes: 1470ddf7f8ce ("inet: Remove explicit write references to sk/inet in ip_append_data")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After pskb_may_pull() we should always refetch the header
pointers from the skb->data in case it got reallocated.
In gre_parse_header(), the erspan header is still fetched
from the 'options' pointer which is fetched before
pskb_may_pull().
Found this during code review of a KMSAN bug report.
Fixes: cb73ee40b1b3 ("net: ip_gre: use erspan key field for tunnel lookup")
Cc: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: William Tu <u9012063@gmail.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Passing NULL to pppoe_pernet causes a crash via BUG_ON.
Dereferencing net in net_generici() also has the same effect. This patch
removes the redundant BUG_ON check on the same parameter.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ / /' -i */Kconfig
Link: http://lkml.kernel.org/r/20191120140140.19148-1-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
DEBUG_FS does not belong to 'Compile-time checks and compiler options'.
Link: http://lkml.kernel.org/r/20190909144453.3520-10-changbin.du@gmail.com
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I think DEBUG_BUGVERBOSE is a dmesg option which gives more debug info
to dmesg.
Link: http://lkml.kernel.org/r/20190909144453.3520-9-changbin.du@gmail.com
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Create a submenu 'Scheduler Debugging' for scheduler debugging options.
Link: http://lkml.kernel.org/r/20190909144453.3520-8-changbin.du@gmail.com
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
They are both memory debug options to debug kernel stack issues.
Link: http://lkml.kernel.org/r/20190909144453.3520-7-changbin.du@gmail.com
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
They are similar options so place them together.
Link: http://lkml.kernel.org/r/20190909144453.3520-6-changbin.du@gmail.com
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Move error injection, coverage, testing options to a new top level
submenu 'Kernel Testing and Coverage'. They are all for test purpose.
Link: http://lkml.kernel.org/r/20190909144453.3520-5-changbin.du@gmail.com
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Group these similar runtime data structures verification options
together.
Link: http://lkml.kernel.org/r/20190909144453.3520-4-changbin.du@gmail.com
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The arch special options are a little long, so create a submenu for
them.
Link: http://lkml.kernel.org/r/20190909144453.3520-3-changbin.du@gmail.com
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
Tony Lindgren
Leonard Crestez
Michael Walle
Arnd Bergmann
Tomi Valkeinen
Christoph Niedermaier
Stefan Wahren
Grygorii Strashko
Mans Rullgard
Geert Uytterhoeven
Florian Fainelli
Nicolas Saenz Julienne
Sudeep Holla
Andreas Kemnade
Stefan Roese
Linus Torvalds
Steve French
Heiner Kallweit
Jiasen Lin
Eric Dumazet
Stefano Garzarella
Cong Wang
Aditya Pakki
Krzysztof Kozlowski
Changbin Du