| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
bcm2835-rpi.dtsi defines the behavior of the ACT LED, which is available
on all Raspberry Pi boards. But there is no driver for this particual
GPIO on CM3 in mainline yet, so this node was left incomplete without
the actual GPIO definition. Since commit 025bf37725f1 ("gpio: Fix return
value mismatch of function gpiod_get_from_of_node()") this causing probe
issues of the leds-gpio driver for users of the CM3 dtsi file.
leds-gpio: probe of leds failed with error -2
Until we have the necessary GPIO driver hide the ACT node for CM3
to avoid this.
Reported-by: Fredrik Yhlen <fredrik.yhlen@endian.se>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Fixes: a54fe8a6cf66 ("ARM: dts: add Raspberry Pi Compute Module 3 and IO board")
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
I noticed that when probed with ti-sysc, watchdog can trigger on am3, am4
and dra7 causing a device reset.
Turns out I made several mistakes implementing the watchdog quirk handling:
1. We must do both writes to spr register
2. We must also call the reset quirk on disable
3. On am3 and am4 we need to also set swsup quirk flag
I probably only tested this earlier with watchdog service running when the
watchdog never gets disabled.
Fixes: 4e23be473e30 ("bus: ti-sysc: Add support for module specific reset quirks")
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The OMAP3 ISP IOMMU does not have any reset lines, so it didn't
need any pdata previously. The OMAP IOMMU driver now requires the
platform data ops for device_enable/idle on all the IOMMU devices
after commit db8918f61d51 ("iommu/omap: streamline enable/disable
through runtime pm callbacks") to enable/disable the clocks properly
and maintain the reference count and the omap_hwmod state machine.
So, add these callbacks through iommu pdata quirks for the OMAP3
ISP IOMMU.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The OMAP IOMMU driver requires the device_enable/idle platform
data ops on all the IOMMU devices to be able to enable and disable
the clocks after commit db8918f61d51 ("iommu/omap: streamline
enable/disable through runtime pm callbacks"). Plug in these
pdata ops for all the existing IOMMUs through pdata quirks to
maintain functionality.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
DA850 EVM has been converted to use GPIO backlight device
for display backlight GPIO control.
Enable the GPIO backlight module in davinci_all_defconfig
to keep backlight support working.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
[nsekhar@ti.com: edits to commit message for context]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
dm365 have only single McBSP, so the device name is without .0
Fixes: 0c750e1fe481d ("ARM: davinci: dm365: Add dma_slave_map to edma")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
The commit e7774049ff25 ("ARM: dts: bcm283x: Define MMC interfaces at
board level") accidently dropped the bus width for the sdhci on the
RPi Zero W, because the board file was relying on the defaults
from bcm2835-rpi.dtsi. So fix this performance regression by adding
the bus width to the board file.
Fixes: e7774049ff25 ("ARM: dts: bcm283x: Define MMC interfaces at board level")
Reported-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Since commit 2eba69071b4b ("drm/msm: Remove Kconfig default") the
CONFIG_DRM_MSM option is no longer selected by default on i.MX5.
Explicitly select CONFIG_DRM_MSM so that we can get GPU support
by default on i.MX51 and i.MX53.
Fixes: 2eba69071b4b ("drm/msm: Remove Kconfig default")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On i.MX8MN, usdhc's ipg clock is from IMX8MN_CLK_IPG_ROOT,
assign it explicitly instead of using IMX8MN_CLK_DUMMY.
Fixes: 6c3debcbae47 ("arm64: dts: freescale: Add i.MX8MN dtsi support")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On i.MX8MM, usdhc's ipg clock is from IMX8MM_CLK_IPG_ROOT,
assign it explicitly instead of using IMX8MM_CLK_DUMMY.
Fixes: a05ea40eb384 ("arm64: dts: imx: Add i.mx8mm dtsi support")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On i.MX8MQ, usdhc's ipg clock is from IMX8MQ_CLK_IPG_ROOT,
assign it explicitly instead of using IMX8MQ_CLK_DUMMY.
Fixes: 748f908cc882 ("arm64: add basic DTS for i.MX8MQ")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
i.MX7S/D's GPT ipg clock should be from GPT clock root and
controlled by CCM's GPT CCGR, using correct clock source for
GPT ipg clock instead of IMX7D_CLK_DUMMY.
Fixes: 3ef79ca6bd1d ("ARM: dts: imx7d: use imx7s.dtsi as base device tree")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Specify 'i2c-mux-idle-disconnect' for both I2C switches present on the
board, since both are connected to the same parent bus and all of
their children have the same I2C address.
Fixes: ca4b4d373fcc ("ARM: dts: vf610: Add ZII SCU4 AIB board")
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Jeff White <jeff.white@zii.aero>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
A previous patch disabled the SNVS power key by default which
breaks the ability for the imx6q-logicpd board to wake from sleep.
This patch re-enables this feature for this board.
Fixes: 770856f0da5d ("ARM: dts: imx6qdl: Enable SNVS power key according to board design")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
lx2160a support PW15 but not PW20, correct name to avoid confusing.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Fixes: 00c5ce8ac023 ("arm64: dts: lx2160a: add cpu idle support")
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
When I re-posted Sean's original commit to add the override mode for
the kevin panel, for some reason I didn't notice that the pixel clock
wasn't quite right. Looking at /sys/kernel/debug/clk/clk_summary on
downstream kernels it can be seen that the VOP clock is supposed to be
266,666,667 Hz achieved by dividing the 800 MHz PLL by 3.
Looking at history, it seems that even Sean's first patch [1] had this
funny clock rate. I'm not sure where it came from since the commit
message specifically mentioned 26666 kHz and the Chrome OS tree [2]
can be seen to request 266667 kHz.
In any case, let's fix it up. This together with my patch [3] to do
the proper rounding when setting the clock rate makes the VOP clock
more proper as seen in /sys/kernel/debug/clk/clk_summary.
[1] https://lore.kernel.org/r/20180206165626.37692-4-seanpaul@chromium.org
[2] https://chromium.googlesource.com/chromiumos/third_party/kernel/+/chromeos-4.4/drivers/gpu/drm/panel/panel-simple.c#1172
[3] https://lkml.kernel.org/r/20191003114726.v2.1.Ib233b3e706cf6317858384264d5b0ed35657456e@changeid
Fixes: 84ebd2da6d04 ("arm64: dts: rockchip: Specify override mode for kevin panel")
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20191008124949.1.I674acd441997dd0690c86c9003743aacda1cf5dd@changeid
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Fix usb-c on X99 TV Box. Tested with armbian w/ kernel 5.3
Signed-off-by: Vivek Unune <npcomplete13@gmail.com>
Link: https://lore.kernel.org/r/20190929032230.24628-1-npcomplete13@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
According to the RockPro64 schematic [1] the rk3399 sdmmc controller is
connected to a microSD (TF card) slot. Remove the cap-mmc-highspeed
property of the sdmmc controller, since no mmc card can be connected here.
[1] http://files.pine64.org/doc/rockpro64/rockpro64_v21-SCH.pdf
Fixes: e4f3fb490967 ("arm64: dts: rockchip: add initial dts support for Rockpro64")
Signed-off-by: Soeren Moch <smoch@web.de>
Link: https://lore.kernel.org/r/20191004203213.4995-1-smoch@web.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Commit 572cf7d7b07d ("ARM: dts: Improve omap l4per idling with wlcore edge
sensitive interrupt") changed wlcore interrupts to use edge interrupt based
on what's specified in the wl1835mod.pdf data sheet.
However, there are still cases where we can have lost interrupts as
described in omap_gpio_unidle(). And using a level interrupt instead of edge
interrupt helps as we avoid the check for untriggered GPIO interrupts in
omap_gpio_unidle().
And with commit e6818d29ea15 ("gpio: gpio-omap: configure edge detection
for level IRQs for idle wakeup") GPIOs idle just fine with level interrupts.
Let's change omap4 and 5 wlcore users back to using level interrupt
instead of edge interrupt. Let's not change the others as I've only seen
this on omap4 and 5, probably because the other SoCs don't have l4per idle
independent of the CPUs.
Fixes: 572cf7d7b07d ("ARM: dts: Improve omap l4per idling with wlcore edge sensitive interrupt")
Depends-on: e6818d29ea15 ("gpio: gpio-omap: configure edge detection for level IRQs for idle wakeup")
Cc: Anders Roxell <anders.roxell@linaro.org>
Cc: Eyal Reizer <eyalr@ti.com>
Cc: Guy Mishol <guym@ti.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Update Turris Mox device tree to use the phy-supply property of the
generic PHY framework instead of the legacy usb-phy property.
This is needed since it caused a regression on Turris Mox since "usb:
host: xhci-plat: Prevent an abnormally restrictive PHY init skipping".
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Fixes: eb6c2eb6c7fb ("usb: host: xhci-plat: Prevent an abnormally restrictive PHY init skipping")
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
According to
Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt,
i2c-mux-idle-disconnect is a property of a parent node since it
pertains to the mux/switch as a whole, so move it there and drop all
of the concurrences in child nodes.
Fixes: d031773169df ("ARM: dts: Adds device tree file for McGill's IceBoard, based on TI AM3874")
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Benoît Cousson <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Graeme Smecher <gsmecher@threespeedlogic.com>
Cc: linux-omap@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Graeme Smecher <gsmecher@threespeedlogic.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The clkctrl code searches for the parent clockdomain based on the name
of the CM provider node. The introduction of SGX node for omap5 made
the node name for the gpu_cm to be clock-controller. There is no
clockdomain named like this, so the lookup fails. Fix by changing
the node name properly.
Fixes: 394534cb07d8 ("ARM: dts: Configure sgx for omap5")
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
What we thought would be the module clock is actually the clock meant to be
used by the sensors, and play no role in the CSI controller. Now that the
binding has been updated to reflect that, let's update the device tree too.
Fixes: d2b9c6444301 ("ARM: dts: sun7i: Add CSI0 controller")
Reported-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
It turns out that what was thought to be the module clock was actually the
clock meant to be used by the sensor, and isn't playing any role with the
CSI controller itself. Let's drop that clock from our binding.
Fixes: c5e8f4ccd775 ("media: dt-bindings: media: Add Allwinner A10 CSI binding")
Reported-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
$id doesn't match the actual filename, so update the $id
Fixes: c5e8f4ccd7750 ("media: dt-bindings: media: Add Allwinner A10 CSI binding")
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
The GPIO controlled regulator for the ARM power supply is supplying
the higher voltage when the GPIO is driven high. This is opposite to
the similar regulator setup on the EVK board and is impacting stability
of the board as the ARM domain has been supplied with a too low voltage
when to faster OPPs are in use.
Fixes: 4a13b3bec3b4 (arm64: dts: imx: add Zii Ultra board support)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The SCU firmware API for getting UID should have response,
otherwise, the message stored in function stack could be
released and then the response data received from SCU will be
stored into that released stack and cause kernel NULL pointer
dump.
Fixes: 73feb4d0f8f1 ("soc: imx-scu: Add SoC UID(unique identifier) support")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The RockPro64 schematics [1], [2] show that the rk3399 EMMC_STRB pin is
connected to the RESET pin instead of the DATA_STROBE pin of the eMMC module.
So the data strobe cannot be used for its intended purpose on this board,
and so the HS400 eMMC mode is not functional. Limit the controller to HS200.
[1] http://files.pine64.org/doc/rockpro64/rockpro64_v21-SCH.pdf
[2] http://files.pine64.org/doc/rock64/PINE64_eMMC_Module_20170719.pdf
Fixes: e4f3fb490967 ("arm64: dts: rockchip: add initial dts support for Rockpro64")
Signed-off-by: Soeren Moch <smoch@web.de>
Link: https://lore.kernel.org/r/20191003215036.15023-2-smoch@web.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The RockPro64 schematic [1] page 18 states a min voltage of 0.8V and a
max voltage of 1.4V for the VDD_LOG pwm regulator. However, there is an
additional note that the pwm parameter needs to be modified.
From the schematics a voltage range of 0.8V to 1.7V can be calculated.
Additional voltage measurements on the board show that this fix indeed
leads to the correct voltage, while without this fix the voltage was set
too high.
[1] http://files.pine64.org/doc/rockpro64/rockpro64_v21-SCH.pdf
Fixes: e4f3fb490967 ("arm64: dts: rockchip: add initial dts support for Rockpro64")
Signed-off-by: Soeren Moch <smoch@web.de>
Link: https://lore.kernel.org/r/20191003215036.15023-1-smoch@web.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
SPI_STM32_QSPI must be set in buildin as rootfs can be
located on QSPI memory device.
Link: https://lore.kernel.org/r/20191004124025.17394-1-patrice.chotard@st.com
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The TWL4030 used on the Logit PD Torpedo SOM does not have the
keypad pins routed. This patch disables the twl_keypad driver
to remove some splat during boot:
twl4030_keypad 48070000.i2c:twl@48:keypad: missing or malformed property linux,keymap: -22
twl4030_keypad 48070000.i2c:twl@48:keypad: Failed to build keymap
twl4030_keypad: probe of 48070000.i2c:twl@48:keypad failed with error -22
Signed-off-by: Adam Ford <aford173@gmail.com>
[tony@atomide.com: removed error time stamps]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The naming convention for the existing Theobroma boards is
soc-q7module-baseboard, so rk3399-puma-haikou and the in-kernel
devicetrees also follow that scheme.
For some reason in the binding a wrong or outdated naming slipped
in which does not match the used devicetrees and makes the dt-schema
complain now.
Fix this by using the names used in the wild by actual boards.
Fixes: a323a513c712 ("dt-bindings: arm: Convert Rockchip board/soc bindings to json-schema")
[although the issue was also present in the old txt file]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20190917083453.25744-1-heiko@sntech.de
|
|
Fix the pinctrl and interrupt specifier for RK808 to use GPIO3_B2. On the
Rockpro64 schematic [1] page 16, it shows GPIO3_B2 used for the interrupt
line PMIC_INT_L from the RK808, and there's a note which translates as:
"PMU termination GPIO1_C5 changed to this".
Tested by setting an RTC wakealarm and checking /proc/interrupts counters.
Without this patch, neither the rockchip_gpio_irq counter for the RK808,
nor the RTC alarm counter increment when the alarm time is reached.
With this patch, both interrupt counters increment by 1 as expected.
[1] http://files.pine64.org/doc/rockpro64/rockpro64_v21-SCH.pdf
Fixes: e4f3fb490967 ("arm64: dts: rockchip: add initial dts support for Rockpro64")
Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com>
Link: https://lore.kernel.org/r/20190921131457.36258-1-sigmaris@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The old omapdrm panels got removed for v5.4 in favor of generic panels,
and the Kconfig options changed. Let's update omap2plus_defconfig
accordingly so the same panels are still enabled.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This fixes up the default ux500 CPU thermal zone:
- Set polling delay to 0 and explain why
- Set passive polling delay to 250
- Remove restrictions from the CPU cooling device,
we should use all cpufreq steps to cool down if
needed.
Link: https://lore.kernel.org/r/20191001074628.8122-1-linus.walleij@linaro.org
Fixes: b786a05f6ce4 ("ARM: dts: ux500: Update thermal zone")
Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
There are total of 151 non-secure gpio (0-150) and four
pins of pinmux (91, 92, 93 and 94) are not mapped to any
gpio pin, hence update same in DT.
Fixes: 8aa428cc1e2e ("arm64: dts: Add pinctrl DT nodes for Stingray SOC")
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
It turns out that sopine-baseboard needs same fix as pine64-plus
for ethernet PHY. Here too Realtek ethernet PHY chip needs additional
power on delay to properly initialize. Datasheet mentions that chip
needs 30 ms to be properly powered on and that it needs some more time
to be initialized.
Fix that by adding 100ms ramp delay to regulator responsible for
powering PHY.
Note that issue was found out and fix tested on pine64-lts, but it's
basically the same as sopine-baseboard, only layout and connectors
differ.
Fixes: bdfe4cebea11 ("arm64: allwinner: a64: add Ethernet PHY regulator for several boards")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
Looks like PMU in A64 is broken, it generates no interrupts at all and
as result 'perf top' shows no events.
Tested on Pine64-LTS.
Fixes: 34a97fcc71c2 ("arm64: dts: allwinner: a64: Add PMU node")
Cc: Harald Geyer <harald@ccbib.org>
Cc: Jared D. McNeill <jmcneill@NetBSD.org>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Emmanuel Vadot <manu@FreeBSD.org>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
Depending on kernel and bootloader configuration, it's possible that
Realtek ethernet PHY isn't powered on properly. According to the
datasheet, it needs 30ms to power up and then some more time before it
can be used.
Fix that by adding 100ms ramp delay to regulator responsible for
powering PHY.
Fixes: 94dcfdc77fc5 ("arm64: allwinner: pine64-plus: Enable dwmac-sun8i")
Suggested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
Commit 6334150e9a36 ("remoteproc: don't allow modular build")
changes CONFIG_REMOTEPROC to a boolean from a tristate config
option which inhibits all defconfigs marking CONFIG_REMOTEPROC as
a module in compiling the remoteproc and dependent config options.
So fix the configs to have CONFIG_REMOTEPROC built in.
Link: https://lore.kernel.org/r/20190920075946.13282-5-j-keerthy@ti.com
Fixes: 6334150e9a36 ("remoteproc: don't allow modular build")
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Will Deacon <will@kernel.org>
[olof: Fixed up all 4 occurrances in this one commit]
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
|
|
Set memory bandwidth limit to filter out resolutions above 720p@60Hz to
avoid underflow errors due to the bandwidth needs of higher resolutions.
am43xx can not provide enough bandwidth to DISPC to correctly handle
'high' resolutions.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Move the static keyword to the front of declaration of
csky_pmu_of_device_ids, and resolve the following compiler
warning that can be seen when building with warnings
enabled (W=1):
arch/csky/kernel/perf_event.c:1340:1: warning:
‘static’ is not at beginning of declaration [-Wold-style-declaration]
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Guo Ren <guoren@kernel.org>
|
|
Since the enabling and disabling of IRQs within preempt_schedule_irq()
is contained in a need_resched() loop, we don't need the outer arch
code loop.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Guo Ren <guoren@kernel.org>
|
|
The csky_pmu.max_period has type u64, and BIT() can only return
32 bits unsigned long on C-SKY. The initialization for max_period
will be incorrect when count_width is bigger than 32.
Use BIT_ULL()
Signed-off-by: Mao Han <han_mao@c-sky.com>
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
|
|
We need set fp zero to let backtrace know the end. The patch fixup perf
callchain panic problem, because backtrace didn't know what is the end
of fp.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Reported-by: Mao Han <han_mao@c-sky.com>
|
|
The csky implementation of free_initrd_mem() is an open-coded version of
free_reserved_area() without poisoning.
Remove it and make csky use the generic version of free_initrd_mem().
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Guo Ren <guoren@kernel.org>
|
|
This reverts commit 72dbcf72156641fde4d8ea401e977341bfd35a05.
Instead of waiting forever for entropy that may just not happen, we now
try to actively generate entropy when required, and are thus hopefully
avoiding the problem that caused the nice ext4 IO pattern fix to be
reverted.
So revert the revert.
Cc: Ahmed S. Darwish <darwish.07@gmail.com>
Cc: Ted Ts'o <tytso@mit.edu>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Alexander E. Patrakov <patrakov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
For 5.3 we had to revert a nice ext4 IO pattern improvement, because it
caused a bootup regression due to lack of entropy at bootup together
with arguably broken user space that was asking for secure random
numbers when it really didn't need to.
See commit 72dbcf721566 (Revert "ext4: make __ext4_get_inode_loc plug").
This aims to solve the issue by actively generating entropy noise using
the CPU cycle counter when waiting for the random number generator to
initialize. This only works when you have a high-frequency time stamp
counter available, but that's the case on all modern x86 CPU's, and on
most other modern CPU's too.
What we do is to generate jitter entropy from the CPU cycle counter
under a somewhat complex load: calling the scheduler while also
guaranteeing a certain amount of timing noise by also triggering a
timer.
I'm sure we can tweak this, and that people will want to look at other
alternatives, but there's been a number of papers written on jitter
entropy, and this should really be fairly conservative by crediting one
bit of entropy for every timer-induced jump in the cycle counter. Not
because the timer itself would be all that unpredictable, but because
the interaction between the timer and the loop is going to be.
Even if (and perhaps particularly if) the timer actually happens on
another CPU, the cacheline interaction between the loop that reads the
cycle counter and the timer itself firing is going to add perturbations
to the cycle counter values that get mixed into the entropy pool.
As Thomas pointed out, with a modern out-of-order CPU, even quite simple
loops show a fair amount of hard-to-predict timing variability even in
the absense of external interrupts. But this tries to take that further
by actually having a fairly complex interaction.
This is not going to solve the entropy issue for architectures that have
no CPU cycle counter, but it's not clear how (and if) that is solvable,
and the hardware in question is largely starting to be irrelevant. And
by doing this we can at least avoid some of the even more contentious
approaches (like making the entropy waiting time out in order to avoid
the possibly unbounded waiting).
Cc: Ahmed Darwish <darwish.07@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Nicholas Mc Guire <hofrat@opentech.at>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Alexander E. Patrakov <patrakov@gmail.com>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The role of the contact list provided by the disclosing party and how it
affects the disclosure process and the ability to include experts into
the development process is not really well explained.
Neither is it entirely clear when the disclosing party will be informed
about the fact that a developer who is not covered by an employer NDA needs
to be brought in and disclosed.
Explain the role of the contact list and the information policy along with
an eventual conflict resolution better.
Reported-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.1909251028390.10825@nanos.tec.linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Stefan Wahren
Tony Lindgren
Suman Anna
Bartosz Golaszewski
Peter Ujfalusi
Fabio Estevam
Anson Huang
Andrey Smirnov
Adam Ford
Ran Wang
Douglas Anderson
Vivek Unune
Soeren Moch
Marek Behún
Tero Kristo
Maxime Ripard
Pragnesh Patel
Lucas Stach
Patrice Chotard
Heiko Stuebner
Hugh Cole-Baker
Linus Walleij
Rayagonda Kokatanur
Jernej Skrabec
Vasily Khoruzhick
Keerthy
Linus Torvalds
Krzysztof Wilczynski
Valentin Schneider
Mao Han
Guo Ren
Mike Rapoport
Thomas Gleixner