| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Whenever a frame was received to the CPU, the HW is timestamping the
frame. In the IFH(Inter Frame Header) it is found the nanosecond part
of the timestamps the SW is required to read from HW the second part.
But reading the second part it seems to be a expensive operations, so
so change this such to read the second part only when rx filter is
enabled.
Doing this change gives the RX a performance boost of ~70mbit.
before:
[ 5] 0.00-10.01 sec 546 MBytes 457 Mbits/sec 0 sender
now:
[ 5] 0.00-10.01 sec 652 MBytes 530 Mbits/sec 0 sender
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use PACKET_SOCK_QDISC_BYPASS atomic bit instead of a pointer.
This removes one indirect call in fast path,
and READ_ONCE()/WRITE_ONCE() annotations as well.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Suggested-by: Willem de Bruijn <willemb@google.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reset TX when halt times out i.e. disable TX, clean up TX BDs,
interrupts (already done) and enable TX.
This addresses the issue observed when iperf is run at 10Mps Half
duplex where, after multiple collisions and retries, TX halts.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are likely no users of this driver as the hardware has been
discontinued since 2010. Remove the driver and all references to it
in documentation.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
of_gpio.h in this driver is solely used as a proxy to other headers.
This is incorrect usage of the of_gpio.h. Replace it .h with what
indeed is used in the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
of_gpio.h in this driver is solely used as a proxy to other headers.
This is incorrect usage of the of_gpio.h. Replace it .h with what
indeed is used in the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently macb sets clock divisor for pclk up to 160 MHz.
Function gem_mdc_clk_div was updated to enable divisor
for higher values of pclk.
Signed-off-by: Bartosz Wawrzyniak <bwawrzyn@cisco.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can change tcp_sk() to propagate its argument const qualifier,
thanks to container_of_const().
We have two places where a const sock pointer has to be upgraded
to a write one. We have been using const qualifier for lockless
listeners to clearly identify points where writes could happen.
Add tcp_sk_rw() helper to better document these.
tcp_inbound_md5_hash(), __tcp_grow_window(), tcp_reset_check()
and tcp_rack_reo_wnd() get an additional const qualififer
for their @tp local variables.
smc_check_reset_syn_req() also needs a similar change.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can change mptcp_sk() to propagate its argument const qualifier,
thanks to container_of_const().
We need to change few things to avoid build errors:
mptcp_set_datafin_timeout() and mptcp_rtx_head() have to accept
non-const sk pointers.
@msk local variable in mptcp_pending_tail() must be const.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Matthieu Baerts <matthieu.baerts@tessares.net>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can change [a]x25_sk() to propagate their argument const qualifier,
thanks to container_of_const().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can change smc_sk() to propagate its argument const qualifier,
thanks to container_of_const().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Karsten Graul <kgraul@linux.ibm.com>
Cc: Wenjia Zhang <wenjia@linux.ibm.com>
Cc: Jan Karcher <jaka@linux.ibm.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can change unix_sk() to propagate its argument const qualifier,
thanks to container_of_const().
We need to change dump_common_audit_data() 'struct unix_sock *u'
local var to get a const attribute.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can change dccp_sk() to propagate its argument const qualifier,
thanks to container_of_const().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can change raw6_sk() to propagate its argument const qualifier,
thanks to container_of_const().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can change raw_sk() to propagate const qualifier of its argument,
thanks to container_of_const()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can change pkt_sk() to propagate const qualifier of its argument,
thanks to container_of_const()
This should avoid some potential errors caused by accidental
(const -> not_const) promotion.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can change udp_sk() to propagate const qualifier of its argument,
thanks to container_of_const()
This should avoid some potential errors caused by accidental
(const -> not_const) promotion.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add HW offloading support for TC flows with VxLAN GBP encap/decap.
Example of encap rule:
tc filter add dev eth0 protocol ip ingress flower \
action tunnel_key set id 42 vxlan_opts 512 \
action mirred egress redirect dev vxlan1
Example of decap rule:
tc filter add dev vxlan1 protocol ip ingress flower \
enc_key_id 42 enc_dst_port 4789 vxlan_opts 1024 \
action tunnel_key unset action mirred egress redirect dev eth0
Signed-off-by: Gavin Li <gavinl@nvidia.com>
Reviewed-by: Gavi Teitz <gavi@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Acked-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Change ip_tunnel_info_opts( ) from static function to macro to cast return
value and preserve the const-ness of the pointer.
Signed-off-by: Gavin Li <gavinl@nvidia.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For tunnels with options, eg, geneve and vxlan with gbp, they share the
same way to compare the headers and options. Extract the code as a common
function for them.
Signed-off-by: Gavin Li <gavinl@nvidia.com>
Reviewed-by: Gavi Teitz <gavi@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Acked-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The function vxlan_build_gbp_hdr will be used by other modules to build
gbp option in vxlan header according to gbp flags.
Signed-off-by: Gavin Li <gavinl@nvidia.com>
Reviewed-by: Gavi Teitz <gavi@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Acked-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove unused argument (i.e. u32 vxflags) in vxlan_build_gbp_hdr( ) and
vxlan_build_gpe_hdr( ) function arguments.
Signed-off-by: Gavin Li <gavinl@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
wwan_port_fops_write inputs the SKB parameter to the TX callback of
the WWAN device driver. However, the WWAN device (e.g., t7xx) may
have an MTU less than the size of SKB, causing the TX buffer to be
sliced and copied once more in the WWAN device driver.
This patch implements the slicing in the WWAN subsystem and gives
the WWAN devices driver the option to slice(by frag_len) or not. By
doing so, the additional memory copy is reduced.
Meanwhile, this patch gives WWAN devices driver the option to reserve
headroom in fragments for the device-specific metadata.
Signed-off-by: haozhe chang <haozhe.chang@mediatek.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/20230316095826.181904-1-haozhe.chang@mediatek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Increase halt timeout to accommodate for 16K SRAM at 10Mbps rounded.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20230316083050.2108-1-harini.katakam@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for SDX65, which uses IPA v5.0.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20230315194305.1647311-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
To avoid excessive mdio bus transactions during probing, mask all phy
addresses that do not exist (there is a 1:1 mapping between switch port
number and phy address).
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Call the rather expensive mv88e6xxx_mdios_register() at the beginning of
mv88e6xxx_setup(). This avoids the double call via mv88e6xxx_probe()
during boot.
For symmetry, call mv88e6xxx_mdios_unregister() at the end of
mv88e6xxx_teardown().
Link: https://lore.kernel.org/lkml/449bde236c08d5ab5e54abd73b645d8b29955894.camel@gmail.com/
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move mv88e6xxx_setup() below mv88e6xxx_mdios_register(), so that we are
able to call the latter one from here. Do the same thing for the
inverse functions.
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
irq_find_mapping() does not need irq_dispose_mapping(), only
irq_create_mapping() does.
Calling irq_dispose_mapping() from mv88e6xxx_g2_irq_mdio_free() and from
the error path of mv88e6xxx_g2_irq_mdio_setup() effectively means that
the mdiobus logic (for internal PHY interrupts) is disposing of a
hwirq->virq mapping which it is not responsible of (but instead, the
function pair mv88e6xxx_g2_irq_setup() + mv88e6xxx_g2_irq_free() is).
With the current code structure, this isn't such a huge problem, because
mv88e6xxx_g2_irq_mdio_free() is called relatively close to the real
owner of the IRQ mappings:
mv88e6xxx_remove()
-> mv88e6xxx_unregister_switch()
-> mv88e6xxx_mdios_unregister()
-> mv88e6xxx_g2_irq_mdio_free()
-> mv88e6xxx_g2_irq_free()
and the switch isn't 'live' in any way such that it would be able of
generating interrupts at this point (mv88e6xxx_unregister_switch() has
been called).
However, there is a desire to split mv88e6xxx_mdios_unregister() and
mv88e6xxx_g2_irq_free() such that mv88e6xxx_mdios_unregister() only gets
called from mv88e6xxx_teardown(). This is much more problematic, as can
be seen below.
In a cross-chip scenario (say 3 switches d0032004.mdio-mii:10,
d0032004.mdio-mii:11 and d0032004.mdio-mii:12 which form a single DSA
tree), it is possible to unbind the device driver from a single switch
(say d0032004.mdio-mii:10).
When that happens, mv88e6xxx_remove() will be called for just that one
switch, and this will call mv88e6xxx_unregister_switch() which will tear
down the entire tree (calling mv88e6xxx_teardown() for all 3 switches).
Assuming mv88e6xxx_mdios_unregister() was moved to mv88e6xxx_teardown(),
at this stage, all 3 switches will have called irq_dispose_mapping() on
their mdiobus virqs.
When we bind again the device driver to d0032004.mdio-mii:10,
mv88e6xxx_probe() is called for it, which calls dsa_register_switch().
The DSA tree is now complete again, and mv88e6xxx_setup() is called for
all 3 switches.
Also assuming that mv88e6xxx_mdios_register() is moved to
mv88e6xxx_setup() (the 2 assumptions go together), at this point,
d0032004.mdio-mii:11 and d0032004.mdio-mii:12 don't have an IRQ mapping
for the internal PHYs anymore, as they've disposed of it in
mv88e6xxx_teardown(). Whereas switch d0032004.mdio-mii:10 has re-created
it, because its code path comes from mv88e6xxx_probe().
Simply put, this change prepares the driver to handle the movement of
mv88e6xxx_mdios_register() to mv88e6xxx_setup() for cross-chip DSA trees.
Also, the code being deleted was partially wrong anyway (in a way which
may have hidden this other issue). mv88e6xxx_g2_irq_mdio_setup()
populates bus->irq[] starting with offset chip->info->phy_base_addr, but
the teardown path doesn't apply that offset too. So it disposes of virq
0 for phy = [ 0, phy_base_addr ).
All switch families have phy_base_addr = 0, except for MV88E6141 and
MV88E6341 which have it as 0x10. I guess those families would have
happened to work by mistake in cross-chip scenarios too.
I'm deleting the body of mv88e6xxx_g2_irq_mdio_free() but leaving its
call sites and prototype in place. This is because, if we ever need to
add back some teardown procedure in the future, it will be perhaps
error-prone to deduce the proper call sites again. Whereas like this,
no extra code should get generated, it shouldn't bother anybody.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove PCI_VENDOR_ID_WANGXUN which is redefined in
drivers/pci/quirks.
Signed-off-by: mengyuanlou <mengyuanlou@net-swift.com>
Link: https://lore.kernel.org/r/20230315091846.17314-1-mengyuanlou@net-swift.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
KVM_HC_CLOCK_PAIRING currently fails inside SEV-SNP guests because the
guest passes an address to static data to the host. In confidential
computing the host can't access arbitrary guest memory so handling the
hypercall runs into an "rmpfault". To make the hypercall work, the guest
needs to explicitly mark the memory as decrypted. Do that in
kvm_arch_ptp_init(), but retain the previous behavior for
non-confidential guests to save us from having to allocate memory.
Add a new arch-specific function (kvm_arch_ptp_exit()) to free the
allocation and mark the memory as encrypted again.
Signed-off-by: Jeremi Piotrowski <jpiotrowski@linux.microsoft.com>
Link: https://lore.kernel.org/r/20230308150531.477741-1-jpiotrowski@linux.microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Happy St. Patrick's Day!
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
The "excursion to minimum" information is in bit2
in HWP_STATUS MSR. Fix the bitmask used for
decoding the register.
Signed-off-by: Antti Laakso <antti.laakso@intel.com>
Reviewed-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Introduce support for EMR.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Tested-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
warn(3) terminates strings with newlines
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
When running as non-root the following error is seen in turbostat:
turbostat: fopen /dev/cpu_dma_latency
: Permission denied
turbostat and the man page have information on how to avoid other
permission errors, so these can be fixed the same way.
Provide better /dev/cpu_dma_latency warnings that provide instructions on
how to avoid the error, and update the man page.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
turbostat reports some capabilities access errors and not others. Provide
the same debug message for all errors.
[lenb: remove extra quotes]
Cc: David Arcari <darcari@redhat.com>
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
cosmetic only (but useful if you copy/paste)
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
The refcount wr_tx_refcnt may cause cache thrashing problems among
cores and we can use percpu ref to mitigate this issue here. We
gain some performance improvement with percpu ref here on our
customized smc-r verion. Applying cache alignment may also mitigate
this problem but it seem more reasonable to use percpu ref here.
We can also replace wr_reg_refcnt with one percpu reference like
wr_tx_refcnt.
redis-benchmark on smc-r with atomic wr_tx_refcnt:
SET: 525707.06 requests per second, p50=0.087 msec
GET: 554877.38 requests per second, p50=0.087 msec
redis-benchmark on the percpu_ref version:
SET: 540482.06 requests per second, p50=0.087 msec
GET: 570711.12 requests per second, p50=0.079 msec
Cases are like "redis-benchmark -h x.x.x.x -q -t set,get -P 1 -n
5000000 -c 50 -d 10 --threads 4".
Signed-off-by: Kai Shen <KaiShen@linux.alibaba.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now both raw_v4_match() and raw_v6_match() accept a const socket,
raw_lookup() can do the same to clarify its role.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This clarifies raw_v4_match() intent.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This clarifies raw_v6_match() intent.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This clarifies __udp_v6_is_mcast_sock() intent.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
inet6_mc_check() is essentially a read-only function.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This clarifies __udp_is_mcast_sock() intent.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This clarifies ip_mc_sf_allow() intent.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can change inet_sk() to propagate const qualifier of its argument.
This should avoid some potential errors caused by accidental
(const -> not_const) promotion.
Other helpers like tcp_sk(), udp_sk(), raw_sk() will be handled
in separate patch series.
v2: use container_of_const() as advised by Jakub and Linus
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/netdev/20230315142841.3a2ac99a@kernel.org/
Link: https://lore.kernel.org/netdev/CAHk-=wiOf12nrYEF2vJMcucKjWPN-Ns_SW9fA7LwST_2Dzp7rw@mail.gmail.com/
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Chuck wanted to put the UAPI header in linux/net/ which seems
reasonable, allow genetlink families to choose the location.
It doesn't really matter for non-C-like languages.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Horatiu Vultur
Eric Dumazet
Harini Katakam
Tony Nguyen
Andy Shevchenko
Bartosz Wawrzyniak
Gavin Li
haozhe chang
Alex Elder
Klaus Kudielka
Vladimir Oltean
mengyuanlou
Jeremi Piotrowski
Len Brown
Antti Laakso
Zhang Rui
Prarit Bhargava
Kai Shen
Jakub Kicinski