Age | Commit message (Collapse) | Author | Files | Lines |
|
Describe the WDT hardware in the RZ/N1 series.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220427135531.708279-2-jjhiblot@traphandler.com
[groeck: Rebased, fixed conflicts]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
Test shows that wachdog still reboots machine after the module
is removed. Use watchdog_stop_on_unregister to stop the watchdog
on removing.
Signed-off-by: Liu Xinpeng <liuxp11@chinatelecom.cn>
eviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1650984810-6247-4-git-send-email-liuxp11@chinatelecom.cn
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
Executing reboot command several times on the machine "Dell
PowerEdge R740", UEFI security detection stopped machine
with the following prompt:
UEFI0082: The system was reset due to a timeout from the watchdog
timer. Check the System Event Log (SEL) or crash dumps from
Operating Sysstem to identify the source that triggered the
watchdog timer reset. Update the firmware or driver for the
identified device.
iDRAC has warning event: "The watchdog timer reset the system".
This patch fixes this issue by adding the reboot notifier.
Signed-off-by: Liu Xinpeng <liuxp11@chinatelecom.cn>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1650984810-6247-3-git-send-email-liuxp11@chinatelecom.cn
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
If max_hw_heartbeat_ms is provided, the configured maximum timeout is not
limited by it. The limit check in this driver therefore doesn't make much
sense. Similar, the watchdog core ensures that minimum timeout limits are
met if min_hw_heartbeat_ms is set. Using watchdog_timeout_invalid() makes
more sense because it takes this into account.
Signed-off-by: Liu Xinpeng <liuxp11@chinatelecom.cn>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1650984810-6247-2-git-send-email-liuxp11@chinatelecom.cn
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
Document the watchdog timeout mode property. If this property is used
the user can select what happens on watchdog timeout. Set this property
to 1 to enable SHUTDOWN (the device resets), set it to 0 and the device
will go to POWERDOWN on watchdog timeout.
If this property is not set, don't touch the WATCHDOG_SD bit and leave
the configuration to OTP. This way backward compatibility is not broken.
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20211206064732.280375-4-andrej.picej@norik.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
Document RZ/G2UL WDT bindings. RZ/G2UL WDT is similar to one found
on the RZ/G2L SoC. No driver changes are required as generic compatible
string "renesas,rzg2l-wdt" will be used as a fallback.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220424071323.151757-1-biju.das.jz@bp.renesas.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
For power management, SET_NOIRQ_SYSTEM_SLEEP_PM_OPS defined for
CONFIG_PM_SLEEP, will point ->suspend_noirq, ->freeze_noirq and
->poweroff_noirq to the same function. Vice versa happens for
->resume_noirq, ->thaw_noirq and ->restore_noirq.
Signed-off-by: Liu Xinpeng <liuxp11@chinatelecom.cn>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1650967905-3199-1-git-send-email-liuxp11@chinatelecom.cn
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
If the device is already in a runtime PM enabled state
pm_runtime_get_sync() will return 1, so a test for negative
value should be used to check for errors.
Fixes: 2d63908bdbfb ("watchdog: Add K3 RTI watchdog support")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220412070824.23708-1-linmq006@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
Add compatibles for the SC8180X and SC8280XP platforms to the Qualcomm
watchdog binding.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220408212854.581481-1-bjorn.andersson@linaro.org
[groeck: Rebased and resolved conflicts]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
This ensures that the same value is read back as was eventually
programmed when using seconds as accuracy. Even then, comparing the more
precise heartbeat_ms against heartbeat in seconds will almost never
provide a match and will needlessly raise a warning. Fix by comparing
apples to apples.
Tested in combination with U-Boot as watchdog starter.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/6a4b54ac-9588-e172-c4c7-b91d524a851e@siemens.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
This refers common bindings, so this is preferred for
unevaluatedProperties instead of additionalProperties.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1649317606-21267-1-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
Disable the watchdog if it is active while removing the module.
It is necessary in order to prevent a reset in case watchdog
hw was running before the removal.
Signed-off-by: Eliav Farber <farbere@amazon.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220414054233.1357-2-farbere@amazon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
Optionally disable watchdog during suspend (if enabled) and re-enable
it upon resume.
This enables boards to sleep without being interrupted by the watchdog.
This patch is based on commit f6c98b08381c ("watchdog: da9062: add
power management ops") and commit 8541673d2a5f ("watchdog: da9062: fix
power management ops") and brings the same functionality to DA9063.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Adam Thomson <DLG-Adam.Thomson.Opensource@dm.renesas.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220422072713.3172345-2-primoz.fiser@norik.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
Document the watchdog disable option which can be used if the hardware
automatic suspend option is broken.
Based on commit c514430c51ee8 ("dt-bindings: watchdog: da9062: add
suspend disable option").
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Adam Thomson <DLG-Adam.Thomson.Opensource@dm.renesas.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220422072713.3172345-1-primoz.fiser@norik.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
Most Allwinner SoCs have just one input clock to drive the watchdog
peripheral. So far this is the 24 MHz "HOSC" oscillator, divided down
internally to 32 KHz.
The F1C100 series watchdog however uses the unchanged 32 KHz "LOSC" as
its only clock input, which has the same effect, but let's the binding
description mismatch.
Change the binding description to name the clocks more loosely, so both
the LOSC and divided HOSC match the description. As the fixed clock names
now make less sense, drop them from SoCs supporting just one clock
input, they were not used by any DT anyway.
For the newer SoCs, supporting a choice of two input clocks, we keep
both the description and clock-names requirement.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220317162349.739636-3-andre.przywara@arm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
The F1C100 series actually features a newer generation watchdog IP, so
the compatible string was wrong.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220317162349.739636-2-andre.przywara@arm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
Sunplus SP7021 requires watchdog timer support.
Add watchdog driver to enable this.
Signed-off-by: Xiantao Hu <xt.hu@cqplus1.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220324031805.61316-3-xt.hu@cqplus1.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
This adds the documentation for the devicetree bindings of the Sunplus
SP7021 watchdog driver, found from SP7021 SoCs and newer.
Signed-off-by: Xiantao Hu <xt.hu@cqplus1.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220324031805.61316-2-xt.hu@cqplus1.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|