| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch is a partial revert of
commit abd7d0972a19 ("arm64: dts: hikey: Enable HS200 mode on eMMC")
which has been causing eMMC corruption on my HiKey board.
Symptoms usually looked like:
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
...
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
mmc0: new HS200 MMC card at address 0001
...
dwmmc_k3 f723d000.dwmmc0: Unexpected command timeout, state 3
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
print_req_error: I/O error, dev mmcblk0, sector 8810504
Aborting journal on device mmcblk0p10-8.
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
EXT4-fs error (device mmcblk0p10): ext4_journal_check_start:61: Detected aborted journal
EXT4-fs (mmcblk0p10): Remounting filesystem read-only
And quite often this would result in a disk that wouldn't properly
boot even with older kernels.
It seems the max-frequency property added by the above patch is
causing the problem, so remove it.
Cc: Ryan Grachek <ryan@edited.us>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: YongQin Liu <yongqin.liu@linaro.org>
Cc: Leo Yan <leo.yan@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Wei Xu <xuwei04@gmail.com>
|
|
qcom_scm_call_atomic1() can crash with a NULL pointer dereference at
qcom_scm_call_atomic1+0x30/0x48.
disassembly of qcom_scm_call_atomic1():
...
<0xc08d73b0 <+12>: ldr r3, [r12]
... (no instruction explicitly modifies r12)
0xc08d73cc <+40>: smc 0
... (no instruction explicitly modifies r12)
0xc08d73d4 <+48>: ldr r3, [r12] <- crashing instruction
...
Since the first ldr is successful, and since r12 isn't explicitly
modified by any instruction between the first and the second ldr,
it must have been modified by the smc call, which is ok,
since r12 is caller save according to the AAPCS.
Add r12 to the clobber list so that the compiler knows that the
callee potentially overwrites the value in r12.
Clobber descriptions may not in any way overlap with an input or
output operand.
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
|
|
Commit 7771c6645700 ("signal/arm: Document conflicts with SI_USER and
SIGFPE") broke the siginfo structure for userspace triggered signals,
causing the strace testsuite to regress. Fix this by eliminating
the FPE_FIXME definition (which is at the root of the breakage) and
use FPE_FLTINV instead for the case where the hardware appears to be
reporting nonsense.
Fixes: 7771c6645700 ("signal/arm: Document conflicts with SI_USER and SIGFPE")
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Commit be83bbf80682 ("mmap: introduce sane default mmap limits") was
introduced to catch problems in various ad-hoc character device drivers
doing mmap and getting the size limits wrong. In the process, it used
"known good" limits for the normal cases of mapping regular files and
block device drivers.
It turns out that the "s_maxbytes" limit was less "known good" than I
thought. In particular, /proc doesn't set it, but exposes one regular
file to mmap: /proc/vmcore. As a result, that file got limited to the
default MAX_INT s_maxbytes value.
This went unnoticed for a while, because apparently the only thing that
needs it is the s390 kernel zfcpdump, but there might be other tools
that use this too.
Vasily suggested just changing s_maxbytes for all of /proc, which isn't
wrong, but makes me nervous at this stage. So instead, just make the
new mmap limit always be MAX_LFS_FILESIZE for regular files, which won't
affect anything else. It wasn't the regular file case I was worried
about.
I'd really prefer for maxsize to have been per-inode, but that is not
how things are today.
Fixes: be83bbf80682 ("mmap: introduce sane default mmap limits")
Reported-by: Vasily Gorbik <gor@linux.ibm.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
... into a global, two-dimensional array and service subsequent reads from
that cache to avoid rdmsr_on_cpu() calls during CPU hotplug (IPIs with IRQs
disabled).
In addition, this fixes a KASAN slab-out-of-bounds read due to wrong usage
of the bank->blocks pointer.
Fixes: 27bd59502702 ("x86/mce/AMD: Get address from already initialized block")
Reported-by: Johannes Hirte <johannes.hirte@datenkhaos.de>
Tested-by: Johannes Hirte <johannes.hirte@datenkhaos.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Yazen Ghannam <yazen.ghannam@amd.com>
Link: http://lkml.kernel.org/r/20180414004230.GA2033@probook
|
|
Since do_undefinstr() uses get_user to get the undefined
instruction, it can be called before kprobes processes
recursive check. This can cause an infinit recursive
exception.
Prohibit probing on get_user functions.
Fixes: 24ba613c9d6c ("ARM kprobes: core code")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Prohibit kprobes on do_undefinstr because kprobes on
arm is implemented by undefined instruction. This means
if we probe do_undefinstr(), it can cause infinit
recursive exception.
Fixes: 24ba613c9d6c ("ARM kprobes: core code")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Prohibit probing on optimized_callback() because
it is called from kprobes itself. If we put a kprobes
on it, that will cause a recursive call loop.
Mark it NOKPROBE_SYMBOL.
Fixes: 0dc016dbd820 ("ARM: kprobes: enable OPTPROBES for ARM 32")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Since get_kprobe_ctlblk() uses smp_processor_id() to access
per-cpu variable, it hits smp_processor_id sanity check as below.
[ 7.006928] BUG: using smp_processor_id() in preemptible [00000000] code: swapper/0/1
[ 7.007859] caller is debug_smp_processor_id+0x20/0x24
[ 7.008438] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.16.0-rc1-00192-g4eb17253e4b5 #1
[ 7.008890] Hardware name: Generic DT based system
[ 7.009917] [<c0313f0c>] (unwind_backtrace) from [<c030e6d8>] (show_stack+0x20/0x24)
[ 7.010473] [<c030e6d8>] (show_stack) from [<c0c64694>] (dump_stack+0x84/0x98)
[ 7.010990] [<c0c64694>] (dump_stack) from [<c071ca5c>] (check_preemption_disabled+0x138/0x13c)
[ 7.011592] [<c071ca5c>] (check_preemption_disabled) from [<c071ca80>] (debug_smp_processor_id+0x20/0x24)
[ 7.012214] [<c071ca80>] (debug_smp_processor_id) from [<c03335e0>] (optimized_callback+0x2c/0xe4)
[ 7.013077] [<c03335e0>] (optimized_callback) from [<bf0021b0>] (0xbf0021b0)
To fix this issue, call get_kprobe_ctlblk() right after
irq-disabled since that disables preemption.
Fixes: 0dc016dbd820 ("ARM: kprobes: enable OPTPROBES for ARM 32")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
You can build a kernel in a cross compiling environment that doesn't
have perl in the $PATH. Commit 429f7a062e3b broke that for 32 bit
ARM. Fix it.
As reported by Stephen Rothwell, it appears that the symbols can be
either part of the BSS section or absolute symbols depending on the
binutils version. When they're an absolute symbol, the $(( ))
operator errors out and the build fails. Fix this as well.
Fixes: 429f7a062e3b ("ARM: decompressor: fix BSS size calculation")
Reported-by: Rob Landley <rob@landley.net>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
How we got to machine_crash_nonpanic_core() (iow, from an IPI, etc) is
not interesting for debugging a crash. The more interesting context
is the parent context prior to the IPI being received.
Record the parent context register state rather than the register state
in machine_crash_nonpanic_core(), which is more relevant to the failing
condition.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
When a panic() occurs, the kexec code uses smp_send_stop() to stop
the other CPUs, but this results in the CPU register state not being
saved, and gdb is unable to inspect the state of other CPUs.
Commit 0ee59413c967 ("x86/panic: replace smp_send_stop() with kdump
friendly version in panic path") addressed the issue on x86, but
ignored other architectures. Address the issue on ARM by splitting
out the crash stop implementation to crash_smp_send_stop() and
adding the necessary protection.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
The hypervisor setup before __enter_kernel destroys the value
sotred in r1. The value needs to be restored just before the jump.
Fixes: 6b52f7bdb888 ("ARM: hyp-stub: Use r1 for the soft-restart address")
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
In commit 639da5ee374b ("ARM: add an extra temp register to the low
level debugging addruart macro") an additional temporary register was
added to the addruart macro, but the decompressor code wasn't updated.
Fixes: 639da5ee374b ("ARM: add an extra temp register to the low level debugging addruart macro")
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
The x86 mmap() code selects the mmap base for an allocation depending on
the bitness of the syscall. For 64bit sycalls it select mm->mmap_base and
for 32bit mm->mmap_compat_base.
exec() calls mmap() which in turn uses in_compat_syscall() to check whether
the mapping is for a 32bit or a 64bit task. The decision is made on the
following criteria:
ia32 child->thread.status & TS_COMPAT
x32 child->pt_regs.orig_ax & __X32_SYSCALL_BIT
ia64 !ia32 && !x32
__set_personality_x32() was dropping TS_COMPAT flag, but
set_personality_64bit() has kept compat syscall flag making
in_compat_syscall() return true during the first exec() syscall.
Which in result has user-visible effects, mentioned by Alexey:
1) It breaks ASAN
$ gcc -fsanitize=address wrap.c -o wrap-asan
$ ./wrap32 ./wrap-asan true
==1217==Shadow memory range interleaves with an existing memory mapping. ASan cannot proceed correctly. ABORTING.
==1217==ASan shadow was supposed to be located in the [0x00007fff7000-0x10007fff7fff] range.
==1217==Process memory map follows:
0x000000400000-0x000000401000 /home/izbyshev/test/gcc/asan-exec-from-32bit/wrap-asan
0x000000600000-0x000000601000 /home/izbyshev/test/gcc/asan-exec-from-32bit/wrap-asan
0x000000601000-0x000000602000 /home/izbyshev/test/gcc/asan-exec-from-32bit/wrap-asan
0x0000f7dbd000-0x0000f7de2000 /lib64/ld-2.27.so
0x0000f7fe2000-0x0000f7fe3000 /lib64/ld-2.27.so
0x0000f7fe3000-0x0000f7fe4000 /lib64/ld-2.27.so
0x0000f7fe4000-0x0000f7fe5000
0x7fed9abff000-0x7fed9af54000
0x7fed9af54000-0x7fed9af6b000 /lib64/libgcc_s.so.1
[snip]
2) It doesn't seem to be great for security if an attacker always knows
that ld.so is going to be mapped into the first 4GB in this case
(the same thing happens for PIEs as well).
The testcase:
$ cat wrap.c
int main(int argc, char *argv[]) {
execvp(argv[1], &argv[1]);
return 127;
}
$ gcc wrap.c -o wrap
$ LD_SHOW_AUXV=1 ./wrap ./wrap true |& grep AT_BASE
AT_BASE: 0x7f63b8309000
AT_BASE: 0x7faec143c000
AT_BASE: 0x7fbdb25fa000
$ gcc -m32 wrap.c -o wrap32
$ LD_SHOW_AUXV=1 ./wrap32 ./wrap true |& grep AT_BASE
AT_BASE: 0xf7eff000
AT_BASE: 0xf7cee000
AT_BASE: 0x7f8b9774e000
Fixes: 1b028f784e8c ("x86/mm: Introduce mmap_compat_base() for 32-bit mmap()")
Fixes: ada26481dfe6 ("x86/mm: Make in_compat_syscall() work during exec")
Reported-by: Alexey Izbyshev <izbyshev@ispras.ru>
Bisected-by: Alexander Monakov <amonakov@ispras.ru>
Investigated-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Alexander Monakov <amonakov@ispras.ru>
Cc: Dmitry Safonov <0x7f454c46@gmail.com>
Cc: stable@vger.kernel.org
Cc: linux-mm@kvack.org
Cc: Andy Lutomirski <luto@kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Link: https://lkml.kernel.org/r/20180517233510.24996-1-dima@arista.com
|
|
With the following commit:
fd35c88b7417 ("objtool: Support GCC 8 switch tables")
I added a "can't find switch jump table" warning, to stop covering up
silent failures if add_switch_table() can't find anything.
That warning found yet another bug in the objtool switch table detection
logic. For cases 1 and 2 (as described in the comments of
find_switch_table()), the find_symbol_containing() check doesn't adjust
the offset for RIP-relative switch jumps.
Incidentally, this bug was already fixed for case 3 with:
6f5ec2993b1f ("objtool: Detect RIP-relative switch table references")
However, that commit missed the fix for cases 1 and 2.
The different cases are now starting to look more and more alike. So
fix the bug by consolidating them into a single case, by checking the
original dynamic jump instruction in the case 3 loop.
This also simplifies the code and makes it more robust against future
switch table detection issues -- of which I'm sure there will be many...
Switch table detection has been the most fragile area of objtool, by
far. I long for the day when we'll have a GCC plugin for annotating
switch tables. Linus asked me to delay such a plugin due to the
flakiness of the plugin infrastructure in older versions of GCC, so this
rickety code is what we're stuck with for now. At least the code is now
a little simpler than it was.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/f400541613d45689086329432f3095119ffbc328.1526674218.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
When CONFIG_RANDOMIZE_TEXT_OFFSET=y, TEXT_OFFSET is an arbitrary
multiple of PAGE_SIZE in the interval [0, 2MB).
The EFI stub does not account for the potential misalignment of
TEXT_OFFSET relative to EFI_KIMG_ALIGN, and produces a randomized
physical offset which is always a round multiple of EFI_KIMG_ALIGN.
This may result in statically allocated objects whose alignment exceeds
PAGE_SIZE to appear misaligned in memory. This has been observed to
result in spurious stack overflow reports and failure to make use of
the IRQ stacks, and theoretically could result in a number of other
issues.
We can OR in the low bits of TEXT_OFFSET to ensure that we have the
necessary offset (and hence preserve the misalignment of TEXT_OFFSET
relative to EFI_KIMG_ALIGN), so let's do that.
Reported-by: Kim Phillips <kim.phillips@arm.com>
Tested-by: Kim Phillips <kim.phillips@arm.com>
[ardb: clarify comment and commit log, drop unneeded parens]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Fixes: 6f26b3671184c36d ("arm64: kaslr: increase randomization granularity")
Link: http://lkml.kernel.org/r/20180518140841.9731-2-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
syzbot is reporting ODEBUG messages at hfsplus_fill_super() [1]. This
is because hfsplus_fill_super() forgot to call cancel_delayed_work_sync().
As far as I can see, it is hfsplus_mark_mdb_dirty() from
hfsplus_new_inode() in hfsplus_fill_super() that calls
queue_delayed_work(). Therefore, I assume that hfsplus_new_inode() does
not fail if queue_delayed_work() was called, and the out_put_hidden_dir
label is the appropriate location to call cancel_delayed_work_sync().
[1] https://syzkaller.appspot.com/bug?id=a66f45e96fdbeb76b796bf46eb25ea878c42a6c9
Link: http://lkml.kernel.org/r/964a8b27-cd69-357c-fe78-76b066056201@I-love.SAKURA.ne.jp
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-by: syzbot <syzbot+4f2e5f086147d543ab03@syzkaller.appspotmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: Ernesto A. Fernandez <ernesto.mnd.fernandez@gmail.com>
Cc: Vyacheslav Dubeyko <slava@dubeyko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It is unsafe to do virtual to physical translations before mm_init() is
called if struct page is needed in order to determine the memory section
number (see SECTION_IN_PAGE_FLAGS). This is because only in mm_init()
we initialize struct pages for all the allocated memory when deferred
struct pages are used.
My recent fix in commit c9e97a1997 ("mm: initialize pages on demand
during boot") exposed this problem, because it greatly reduced number of
pages that are initialized before mm_init(), but the problem existed
even before my fix, as Fengguang Wu found.
Below is a more detailed explanation of the problem.
We initialize struct pages in four places:
1. Early in boot a small set of struct pages is initialized to fill the
first section, and lower zones.
2. During mm_init() we initialize "struct pages" for all the memory that
is allocated, i.e reserved in memblock.
3. Using on-demand logic when pages are allocated after mm_init call
(when memblock is finished)
4. After smp_init() when the rest free deferred pages are initialized.
The problem occurs if we try to do va to phys translation of a memory
between steps 1 and 2. Because we have not yet initialized struct pages
for all the reserved pages, it is inherently unsafe to do va to phys if
the translation itself requires access of "struct page" as in case of
this combination: CONFIG_SPARSE && !CONFIG_SPARSE_VMEMMAP
The following path exposes the problem:
start_kernel()
trap_init()
setup_cpu_entry_areas()
setup_cpu_entry_area(cpu)
get_cpu_gdt_paddr(cpu)
per_cpu_ptr_to_phys(addr)
pcpu_addr_to_page(addr)
virt_to_page(addr)
pfn_to_page(__pa(addr) >> PAGE_SHIFT)
We disable this path by not allowing NEED_PER_CPU_KM with deferred
struct pages feature.
The problems are discussed in these threads:
http://lkml.kernel.org/r/20180418135300.inazvpxjxowogyge@wfg-t540p.sh.intel.com
http://lkml.kernel.org/r/20180419013128.iurzouiqxvcnpbvz@wfg-t540p.sh.intel.com
http://lkml.kernel.org/r/20180426202619.2768-1-pasha.tatashin@oracle.com
Link: http://lkml.kernel.org/r/20180515175124.1770-1-pasha.tatashin@oracle.com
Fixes: 3a80a7fa7989 ("mm: meminit: initialise a subset of struct pages if CONFIG_DEFERRED_STRUCT_PAGE_INIT is set")
Signed-off-by: Pavel Tatashin <pasha.tatashin@oracle.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Steven Sistare <steven.sistare@oracle.com>
Cc: Daniel Jordan <daniel.m.jordan@oracle.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Dennis Zhou <dennisszhou@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
A new patchwork project is created to track kselftest patches. Update
the kselftest entry in the MAINTAINERS file adding 'Q:' entry:
https://patchwork.kernel.org/project/linux-kselftest/list/
Link: http://lkml.kernel.org/r/20180515164427.12201-1-shuah@kernel.org
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix a race in the multi-order iteration code which causes the kernel to
hit a GP fault. This was first seen with a production v4.15 based
kernel (4.15.6-300.fc27.x86_64) utilizing a DAX workload which used
order 9 PMD DAX entries.
The race has to do with how we tear down multi-order sibling entries
when we are removing an item from the tree. Remember for example that
an order 2 entry looks like this:
struct radix_tree_node.slots[] = [entry][sibling][sibling][sibling]
where 'entry' is in some slot in the struct radix_tree_node, and the
three slots following 'entry' contain sibling pointers which point back
to 'entry.'
When we delete 'entry' from the tree, we call :
radix_tree_delete()
radix_tree_delete_item()
__radix_tree_delete()
replace_slot()
replace_slot() first removes the siblings in order from the first to the
last, then at then replaces 'entry' with NULL. This means that for a
brief period of time we end up with one or more of the siblings removed,
so:
struct radix_tree_node.slots[] = [entry][NULL][sibling][sibling]
This causes an issue if you have a reader iterating over the slots in
the tree via radix_tree_for_each_slot() while only under
rcu_read_lock()/rcu_read_unlock() protection. This is a common case in
mm/filemap.c.
The issue is that when __radix_tree_next_slot() => skip_siblings() tries
to skip over the sibling entries in the slots, it currently does so with
an exact match on the slot directly preceding our current slot.
Normally this works:
V preceding slot
struct radix_tree_node.slots[] = [entry][sibling][sibling][sibling]
^ current slot
This lets you find the first sibling, and you skip them all in order.
But in the case where one of the siblings is NULL, that slot is skipped
and then our sibling detection is interrupted:
V preceding slot
struct radix_tree_node.slots[] = [entry][NULL][sibling][sibling]
^ current slot
This means that the sibling pointers aren't recognized since they point
all the way back to 'entry', so we think that they are normal internal
radix tree pointers. This causes us to think we need to walk down to a
struct radix_tree_node starting at the address of 'entry'.
In a real running kernel this will crash the thread with a GP fault when
you try and dereference the slots in your broken node starting at
'entry'.
We fix this race by fixing the way that skip_siblings() detects sibling
nodes. Instead of testing against the preceding slot we instead look
for siblings via is_sibling_entry() which compares against the position
of the struct radix_tree_node.slots[] array. This ensures that sibling
entries are properly identified, even if they are no longer contiguous
with the 'entry' they point to.
Link: http://lkml.kernel.org/r/20180503192430.7582-6-ross.zwisler@linux.intel.com
Fixes: 148deab223b2 ("radix-tree: improve multiorder iterators")
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reported-by: CR, Sapthagirish <sapthagirish.cr@intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add a test which shows a race in the multi-order iteration code. This
test reliably hits the race in under a second on my machine, and is the
result of a real bug report against kernel a production v4.15 based
kernel (4.15.6-300.fc27.x86_64). With a real kernel this issue is hit
when using order 9 PMD DAX radix tree entries.
The race has to do with how we tear down multi-order sibling entries
when we are removing an item from the tree. Remember that an order 2
entry looks like this:
struct radix_tree_node.slots[] = [entry][sibling][sibling][sibling]
where 'entry' is in some slot in the struct radix_tree_node, and the
three slots following 'entry' contain sibling pointers which point back
to 'entry.'
When we delete 'entry' from the tree, we call :
radix_tree_delete()
radix_tree_delete_item()
__radix_tree_delete()
replace_slot()
replace_slot() first removes the siblings in order from the first to the
last, then at then replaces 'entry' with NULL. This means that for a
brief period of time we end up with one or more of the siblings removed,
so:
struct radix_tree_node.slots[] = [entry][NULL][sibling][sibling]
This causes an issue if you have a reader iterating over the slots in
the tree via radix_tree_for_each_slot() while only under
rcu_read_lock()/rcu_read_unlock() protection. This is a common case in
mm/filemap.c.
The issue is that when __radix_tree_next_slot() => skip_siblings() tries
to skip over the sibling entries in the slots, it currently does so with
an exact match on the slot directly preceding our current slot.
Normally this works:
V preceding slot
struct radix_tree_node.slots[] = [entry][sibling][sibling][sibling]
^ current slot
This lets you find the first sibling, and you skip them all in order.
But in the case where one of the siblings is NULL, that slot is skipped
and then our sibling detection is interrupted:
V preceding slot
struct radix_tree_node.slots[] = [entry][NULL][sibling][sibling]
^ current slot
This means that the sibling pointers aren't recognized since they point
all the way back to 'entry', so we think that they are normal internal
radix tree pointers. This causes us to think we need to walk down to a
struct radix_tree_node starting at the address of 'entry'.
In a real running kernel this will crash the thread with a GP fault when
you try and dereference the slots in your broken node starting at
'entry'.
In the radix tree test suite this will be caught by the address
sanitizer:
==27063==ERROR: AddressSanitizer: heap-buffer-overflow on address
0x60c0008ae400 at pc 0x00000040ce4f bp 0x7fa89b8fcad0 sp 0x7fa89b8fcac0
READ of size 8 at 0x60c0008ae400 thread T3
#0 0x40ce4e in __radix_tree_next_slot /home/rzwisler/project/linux/tools/testing/radix-tree/radix-tree.c:1660
#1 0x4022cc in radix_tree_next_slot linux/../../../../include/linux/radix-tree.h:567
#2 0x4022cc in iterator_func /home/rzwisler/project/linux/tools/testing/radix-tree/multiorder.c:655
#3 0x7fa8a088d50a in start_thread (/lib64/libpthread.so.0+0x750a)
#4 0x7fa8a03bd16e in clone (/lib64/libc.so.6+0xf516e)
Link: http://lkml.kernel.org/r/20180503192430.7582-5-ross.zwisler@linux.intel.com
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: CR, Sapthagirish <sapthagirish.cr@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently the lifetime of "struct item" entries in the radix tree are
not controlled by RCU, but are instead deleted inline as they are
removed from the tree.
In the following patches we add a test which has threads iterating over
items pulled from the tree and verifying them in an
rcu_read_lock()/rcu_read_unlock() section. This means that though an
item has been removed from the tree it could still be being worked on by
other threads until the RCU grace period expires. So, we need to
actually free the "struct item" structures at the end of the grace
period, just as we do with "struct radix_tree_node" items.
Link: http://lkml.kernel.org/r/20180503192430.7582-4-ross.zwisler@linux.intel.com
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: CR, Sapthagirish <sapthagirish.cr@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pulled from a patch from Matthew Wilcox entitled "xarray: Add definition
of struct xarray":
> From: Matthew Wilcox <mawilcox@microsoft.com>
> Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
https://patchwork.kernel.org/patch/10341249/
These defines fix this compilation error:
In file included from ./linux/radix-tree.h:6:0,
from ./linux/../../../../include/linux/idr.h:15,
from ./linux/idr.h:1,
from idr.c:4:
./linux/../../../../include/linux/idr.h: In function `idr_init_base':
./linux/../../../../include/linux/radix-tree.h:129:2: warning: implicit declaration of function `spin_lock_init'; did you mean `spinlock_t'? [-Wimplicit-function-declaration]
spin_lock_init(&(root)->xa_lock); \
^
./linux/../../../../include/linux/idr.h:126:2: note: in expansion of macro `INIT_RADIX_TREE'
INIT_RADIX_TREE(&idr->idr_rt, IDR_RT_MARKER);
^~~~~~~~~~~~~~~
by providing a spin_lock_init() wrapper for the v4.17-rc* version of the
radix tree test suite.
Link: http://lkml.kernel.org/r/20180503192430.7582-3-ross.zwisler@linux.intel.com
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: CR, Sapthagirish <sapthagirish.cr@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit c6ce3e2fe3da ("radix tree test suite: Add config option for map
shift") introduced a phony makefile target called 'mapshift' that ends
up generating the file generated/map-shift.h. This phony target was
then added as a dependency of the top level 'targets' build target,
which is what is run when you go to tools/testing/radix-tree and just
type 'make'.
Unfortunately, this phony target doesn't actually work as a dependency,
so you end up getting:
$ make
make: *** No rule to make target 'generated/map-shift.h', needed by 'main.o'. Stop.
make: *** Waiting for unfinished jobs....
Fix this by making the file generated/map-shift.h our real makefile
target, and add this a dependency of the top level build target.
Link: http://lkml.kernel.org/r/20180503192430.7582-2-ross.zwisler@linux.intel.com
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: CR, Sapthagirish <sapthagirish.cr@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Many places in drivers/ file systems, error was handled in a common way
like below:
ret = (ret == -ENOMEM) ? VM_FAULT_OOM : VM_FAULT_SIGBUS;
vmf_error() will replace this and return vm_fault_t type err.
A lot of drivers and filesystems currently have a rather complex mapping
of errno-to-VM_FAULT code. We have been able to eliminate a lot of it
by just returning VM_FAULT codes directly from functions which are
called exclusively from the fault handling path.
Some functions can be called both from the fault handler and other
context which are expecting an errno, so they have to continue to return
an errno. Some users still need to choose different behaviour for
different errnos, but vmf_error() captures the essential error
translation that's common to all users, and those that need to handle
additional errors can handle them first.
Link: http://lkml.kernel.org/r/20180510174826.GA14268@jordon-HP-15-Notebook-PC
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Reviewed-by: Matthew Wilcox <mawilcox@microsoft.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I had neglected to increment the error counter when the tests failed,
which made the tests noisy when they fail, but not actually return an
error code.
Link: http://lkml.kernel.org/r/20180509114328.9887-1-mpe@ellerman.id.au
Fixes: 3cc78125a081 ("lib/test_bitmap.c: add optimisation tests")
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Tested-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Yury Norov <ynorov@caviumnetworks.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: <stable@vger.kernel.org> [4.13+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If DELL_WMI "select"s DELL_SMBIOS, the DELL_SMBIOS dependencies are
ignored and it is still possible to end up with unmet direct
dependencies.
Change the select to a depends on.
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
ccio_cujo20_fixup() is called by dino_probe() only, which is in init
section already.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
No other architecture has setup_profiling_timer() in the init section,
thus on parisc we face this section mismatch warning:
Reference from the function devm_device_add_group() to the function .init.text:setup_profiling_timer()
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
The 0-DAY kernel test infrastructure reported that inet_put_port() may
reference the find_pa_parent_type() function, so it can't be moved into the
init section.
Fixes: b86db40e1ecc ("parisc: Move various functions and strings to init section")
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
The 'tip' prefix probably referred to the -tip tree and is not required,
remove it.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Turner <pjt@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180515165328.24899-1-bigeasy@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Since the grub_reclaim() function can be made static, make it so.
Silences the following GCC warning (W=1):
kernel/sched/deadline.c:1120:5: warning: no previous prototype for ‘grub_reclaim’ [-Wmissing-prototypes]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180516200902.959-1-malat@debian.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
In the following commit:
6b55c9654fcc ("sched/debug: Move print_cfs_rq() declaration to kernel/sched/sched.h")
the print_cfs_rq() prototype was added to <kernel/sched/sched.h>,
right next to the prototypes for print_cfs_stats(), print_rt_stats()
and print_dl_stats().
Finish this previous commit and also move related prototypes for
print_rt_rq() and print_dl_rq().
Remove existing extern declarations now that they not needed anymore.
Silences the following GCC warning, triggered by W=1:
kernel/sched/debug.c:573:6: warning: no previous prototype for ‘print_rt_rq’ [-Wmissing-prototypes]
kernel/sched/debug.c:603:6: warning: no previous prototype for ‘print_dl_rq’ [-Wmissing-prototypes]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180516195348.30426-1-malat@debian.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Rick bisected a regression on large systems which use the x2apic cluster
mode for interrupt delivery to the commit wich reworked the cluster
management.
The problem is caused by a missing initialization of the clusterid field
in the shared cluster data structures. So all structures end up with
cluster ID 0 which only allows sharing between all CPUs which belong to
cluster 0. All other CPUs with a cluster ID > 0 cannot share the data
structure because they cannot find existing data with their cluster
ID. This causes malfunction with IPIs because IPIs are sent to the wrong
cluster and the caller waits for ever that the target CPU handles the IPI.
Add the missing initialization when a upcoming CPU is the first in a
cluster so that the later booting CPUs can find the data and share it for
proper operation.
Fixes: 023a611748fd ("x86/apic/x2apic: Simplify cluster management")
Reported-by: Rick Warner <rick@microway.com>
Bisected-by: Rick Warner <rick@microway.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Rick Warner <rick@microway.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1805171418210.1947@nanos.tec.linutronix.de
|
|
KVM_HINTS_DEDICATED seems to be somewhat confusing:
Guest doesn't really care whether it's the only task running on a host
CPU as long as it's not preempted.
And there are more reasons for Guest to be preempted than host CPU
sharing, for example, with memory overcommit it can get preempted on a
memory access, post copy migration can cause preemption, etc.
Let's call it KVM_HINTS_REALTIME which seems to better
match what guests expect.
Also, the flag most be set on all vCPUs - current guests assume this.
Note so in the documentation.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
proc_pid_cmdline_read() and environ_read() directly access the target
process' VM to retrieve the command line and environment. If this
process remaps these areas onto a file via mmap(), the requesting
process may experience various issues such as extra delays if the
underlying device is slow to respond.
Let's simply refuse to access file-backed areas in these functions.
For this we add a new FOLL_ANON gup flag that is passed to all calls
to access_remote_vm(). The code already takes care of such failures
(including unmapped areas). Accesses via /proc/pid/mem were not
changed though.
This was assigned CVE-2018-1120.
Note for stable backports: the patch may apply to kernels prior to 4.11
but silently miss one location; it must be checked that no call to
access_remote_vm() keeps zero as the last argument.
Reported-by: Qualys Security Advisory <qsa@qualys.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 539d39eb2708 ("bcache: fix wrong return value in bch_debug_init()")
returns the return value of debugfs_create_dir() to bcache_init(). When
CONFIG_DEBUG_FS=n, bch_debug_init() always returns 1 and makes
bcache_init() failedi.
This patch makes bch_debug_init() always returns 0 if CONFIG_DEBUG_FS=n,
so bcache can continue to work for the kernels which don't have debugfs
enanbled.
Changelog:
v4: Add Acked-by from Kent Overstreet.
v3: Use IS_ENABLED(CONFIG_DEBUG_FS) to replace #ifdef DEBUG_FS.
v2: Remove a warning information
v1: Initial version.
Fixes: Commit 539d39eb2708 ("bcache: fix wrong return value in bch_debug_init()")
Cc: stable@vger.kernel.org
Signed-off-by: Coly Li <colyli@suse.de>
Reported-by: Massimo B. <massimo.b@gmx.net>
Reported-by: Kai Krakow <kai@kaishome.de>
Tested-by: Kai Krakow <kai@kaishome.de>
Acked-by: Kent Overstreet <kent.overstreet@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Similarly to opal_event_shutdown, opal_nvram_write can be called in
the crash path with irqs disabled. Special case the delay to avoid
sleeping in invalid context.
Fixes: 3b8070335f75 ("powerpc/powernv: Fix OPAL NVRAM driver OPAL_BUSY loops")
Cc: stable@vger.kernel.org # v3.2
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Add I2C/SMBUS Driver entry for STM32 family from ST Microelectronics.
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
We set the BTRFS_BALANCE_RESUME flag in the btrfs_recover_balance()
only, which isn't called during the remount. So when resuming from
the paused balance we hit the bug:
kernel: kernel BUG at fs/btrfs/volumes.c:3890!
::
kernel: balance_kthread+0x51/0x60 [btrfs]
kernel: kthread+0x111/0x130
::
kernel: RIP: btrfs_balance+0x12e1/0x1570 [btrfs] RSP: ffffba7d0090bde8
Reproducer:
On a mounted filesystem:
btrfs balance start --full-balance /btrfs
btrfs balance pause /btrfs
mount -o remount,ro /dev/sdb /btrfs
mount -o remount,rw /dev/sdb /btrfs
To fix this set the BTRFS_BALANCE_RESUME flag in
btrfs_resume_balance_async().
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
When a transaction is aborted btrfs_cleanup_transaction is called to
cleanup all the various in-flight bits and pieces which migth be
active. One of those is delalloc inodes - inodes which have dirty
pages which haven't been persisted yet. Currently the process of
freeing such delalloc inodes in exceptional circumstances such as
transaction abort boiled down to calling btrfs_invalidate_inodes whose
sole job is to invalidate the dentries for all inodes related to a
root. This is in fact wrong and insufficient since such delalloc inodes
will likely have pending pages or ordered-extents and will be linked to
the sb->s_inode_list. This means that unmounting a btrfs instance with
an aborted transaction could potentially lead inodes/their pages
visible to the system long after their superblock has been freed. This
in turn leads to a "use-after-free" situation once page shrink is
triggered. This situation could be simulated by running generic/019
which would cause such inodes to be left hanging, followed by
generic/176 which causes memory pressure and page eviction which lead
to touching the freed super block instance. This situation is
additionally detected by the unmount code of VFS with the following
message:
"VFS: Busy inodes after unmount of Self-destruct in 5 seconds. Have a nice day..."
Additionally btrfs hits WARN_ON(!RB_EMPTY_ROOT(&root->inode_tree));
in free_fs_root for the same reason.
This patch aims to rectify the sitaution by doing the following:
1. Change btrfs_destroy_delalloc_inodes so that it calls
invalidate_inode_pages2 for every inode on the delalloc list, this
ensures that all the pages of the inode are released. This function
boils down to calling btrfs_releasepage. During test I observed cases
where inodes on the delalloc list were having an i_count of 0, so this
necessitates using igrab to be sure we are working on a non-freed inode.
2. Since calling btrfs_releasepage might queue delayed iputs move the
call out to btrfs_cleanup_transaction in btrfs_error_commit_super before
calling run_delayed_iputs for the last time. This is necessary to ensure
that delayed iputs are run.
Note: this patch is tagged for 4.14 stable but the fix applies to older
versions too but needs to be backported manually due to conflicts.
CC: stable@vger.kernel.org # 4.14.x: 2b8773313494: btrfs: Split btrfs_del_delalloc_inode into 2 functions
CC: stable@vger.kernel.org # 4.14.x
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ add comment to igrab ]
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
This is in preparation of fixing delalloc inodes leakage on transaction
abort. Also export the new function.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
If a btree block, aka. extent buffer, is not available in the extent
buffer cache, it'll be read out from the disk instead, i.e.
btrfs_search_slot()
read_block_for_search() # hold parent and its lock, go to read child
btrfs_release_path()
read_tree_block() # read child
Unfortunately, the parent lock got released before reading child, so
commit 5bdd3536cbbe ("Btrfs: Fix block generation verification race") had
used 0 as parent transid to read the child block. It forces
read_tree_block() not to check if parent transid is different with the
generation id of the child that it reads out from disk.
A simple PoC is included in btrfs/124,
0. A two-disk raid1 btrfs,
1. Right after mkfs.btrfs, block A is allocated to be device tree's root.
2. Mount this filesystem and put it in use, after a while, device tree's
root got COW but block A hasn't been allocated/overwritten yet.
3. Umount it and reload the btrfs module to remove both disks from the
global @fs_devices list.
4. mount -odegraded dev1 and write some data, so now block A is allocated
to be a leaf in checksum tree. Note that only dev1 has the latest
metadata of this filesystem.
5. Umount it and mount it again normally (with both disks), since raid1
can pick up one disk by the writer task's pid, if btrfs_search_slot()
needs to read block A, dev2 which does NOT have the latest metadata
might be read for block A, then we got a stale block A.
6. As parent transid is not checked, block A is marked as uptodate and
put into the extent buffer cache, so the future search won't bother
to read disk again, which means it'll make changes on this stale
one and make it dirty and flush it onto disk.
To avoid the problem, parent transid needs to be passed to
read_tree_block().
In order to get a valid parent transid, we need to hold the parent's
lock until finishing reading child.
This patch needs to be slightly adapted for stable kernels, the
&first_key parameter added to read_tree_block() is from 4.16+
(581c1760415c4). The fix is to replace 0 by 'gen'.
Fixes: 5bdd3536cbbe ("Btrfs: Fix block generation verification race")
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Liu Bo <bo.liu@linux.alibaba.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
[ update changelog ]
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Incompat flag of LZO/ZSTD compression should be set at:
1. mount time (-o compress/compress-force)
2. when defrag is done
3. when property is set
Currently 3. is missing and this commit adds this.
This could lead to a filesystem that uses ZSTD but is not marked as
such. If a kernel without a ZSTD support encounteres a ZSTD compressed
extent, it will handle that but this could be confusing to the user.
Typically the filesystem is mounted with the ZSTD option, but the
discrepancy can arise when a filesystem is never mounted with ZSTD and
then the property on some file is set (and some new extents are
written). A simple mount with -o compress=zstd will fix that up on an
unpatched kernel.
Same goes for LZO, but this has been around for a very long time
(2.6.37) so it's unlikely that a pre-LZO kernel would be used.
Fixes: 5c1aab1dd544 ("btrfs: Add zstd support")
CC: stable@vger.kernel.org # 4.14+
Signed-off-by: Tomohiro Misono <misono.tomohiro@jp.fujitsu.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ add user visible impact ]
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
In commit 471d557afed1 ("Btrfs: fix loss of prealloc extents past i_size
after fsync log replay"), on fsync, we started to always log all prealloc
extents beyond an inode's i_size in order to avoid losing them after a
power failure. However under some cases this can lead to the log replay
code to create duplicate extent items, with different lengths, in the
extent tree. That happens because, as of that commit, we can now log
extent items based on extent maps that are not on the "modified" list
of extent maps of the inode's extent map tree. Logging extent items based
on extent maps is used during the fast fsync path to save time and for
this to work reliably it requires that the extent maps are not merged
with other adjacent extent maps - having the extent maps in the list
of modified extents gives such guarantee.
Consider the following example, captured during a long run of fsstress,
which illustrates this problem.
We have inode 271, in the filesystem tree (root 5), for which all of the
following operations and discussion apply to.
A buffered write starts at offset 312391 with a length of 933471 bytes
(end offset at 1245862). At this point we have, for this inode, the
following extent maps with the their field values:
em A, start 0, orig_start 0, len 40960, block_start 18446744073709551613,
block_len 0, orig_block_len 0
em B, start 40960, orig_start 40960, len 376832, block_start 1106399232,
block_len 376832, orig_block_len 376832
em C, start 417792, orig_start 417792, len 782336, block_start
18446744073709551613, block_len 0, orig_block_len 0
em D, start 1200128, orig_start 1200128, len 835584, block_start
1106776064, block_len 835584, orig_block_len 835584
em E, start 2035712, orig_start 2035712, len 245760, block_start
1107611648, block_len 245760, orig_block_len 245760
Extent map A corresponds to a hole and extent maps D and E correspond to
preallocated extents.
Extent map D ends where extent map E begins (1106776064 + 835584 =
1107611648), but these extent maps were not merged because they are in
the inode's list of modified extent maps.
An fsync against this inode is made, which triggers the fast path
(BTRFS_INODE_NEEDS_FULL_SYNC is not set). This fsync triggers writeback
of the data previously written using buffered IO, and when the respective
ordered extent finishes, btrfs_drop_extents() is called against the
(aligned) range 311296..1249279. This causes a split of extent map D at
btrfs_drop_extent_cache(), replacing extent map D with a new extent map
D', also added to the list of modified extents, with the following
values:
em D', start 1249280, orig_start of 1200128,
block_start 1106825216 (= 1106776064 + 1249280 - 1200128),
orig_block_len 835584,
block_len 786432 (835584 - (1249280 - 1200128))
Then, during the fast fsync, btrfs_log_changed_extents() is called and
extent maps D' and E are removed from the list of modified extents. The
flag EXTENT_FLAG_LOGGING is also set on them. After the extents are logged
clear_em_logging() is called on each of them, and that makes extent map E
to be merged with extent map D' (try_merge_map()), resulting in D' being
deleted and E adjusted to:
em E, start 1249280, orig_start 1200128, len 1032192,
block_start 1106825216, block_len 1032192,
orig_block_len 245760
A direct IO write at offset 1847296 and length of 360448 bytes (end offset
at 2207744) starts, and at that moment the following extent maps exist for
our inode:
em A, start 0, orig_start 0, len 40960, block_start 18446744073709551613,
block_len 0, orig_block_len 0
em B, start 40960, orig_start 40960, len 270336, block_start 1106399232,
block_len 270336, orig_block_len 376832
em C, start 311296, orig_start 311296, len 937984, block_start 1112842240,
block_len 937984, orig_block_len 937984
em E (prealloc), start 1249280, orig_start 1200128, len 1032192,
block_start 1106825216, block_len 1032192, orig_block_len 245760
The dio write results in drop_extent_cache() being called twice. The first
time for a range that starts at offset 1847296 and ends at offset 2035711
(length of 188416), which results in a double split of extent map E,
replacing it with two new extent maps:
em F, start 1249280, orig_start 1200128, block_start 1106825216,
block_len 598016, orig_block_len 598016
em G, start 2035712, orig_start 1200128, block_start 1107611648,
block_len 245760, orig_block_len 1032192
It also creates a new extent map that represents a part of the requested
IO (through create_io_em()):
em H, start 1847296, len 188416, block_start 1107423232, block_len 188416
The second call to drop_extent_cache() has a range with a start offset of
2035712 and end offset of 2207743 (length of 172032). This leads to
replacing extent map G with a new extent map I with the following values:
em I, start 2207744, orig_start 1200128, block_start 1107783680,
block_len 73728, orig_block_len 1032192
It also creates a new extent map that represents the second part of the
requested IO (through create_io_em()):
em J, start 2035712, len 172032, block_start 1107611648, block_len 172032
The dio write set the inode's i_size to 2207744 bytes.
After the dio write the inode has the following extent maps:
em A, start 0, orig_start 0, len 40960, block_start 18446744073709551613,
block_len 0, orig_block_len 0
em B, start 40960, orig_start 40960, len 270336, block_start 1106399232,
block_len 270336, orig_block_len 376832
em C, start 311296, orig_start 311296, len 937984, block_start 1112842240,
block_len 937984, orig_block_len 937984
em F, start 1249280, orig_start 1200128, len 598016,
block_start 1106825216, block_len 598016, orig_block_len 598016
em H, start 1847296, orig_start 1200128, len 188416,
block_start 1107423232, block_len 188416, orig_block_len 835584
em J, start 2035712, orig_start 2035712, len 172032,
block_start 1107611648, block_len 172032, orig_block_len 245760
em I, start 2207744, orig_start 1200128, len 73728,
block_start 1107783680, block_len 73728, orig_block_len 1032192
Now do some change to the file, like adding a xattr for example and then
fsync it again. This triggers a fast fsync path, and as of commit
471d557afed1 ("Btrfs: fix loss of prealloc extents past i_size after fsync
log replay"), we use the extent map I to log a file extent item because
it's a prealloc extent and it starts at an offset matching the inode's
i_size. However when we log it, we create a file extent item with a value
for the disk byte location that is wrong, as can be seen from the
following output of "btrfs inspect-internal dump-tree":
item 1 key (271 EXTENT_DATA 2207744) itemoff 3782 itemsize 53
generation 22 type 2 (prealloc)
prealloc data disk byte 1106776064 nr 1032192
prealloc data offset 1007616 nr 73728
Here the disk byte value corresponds to calculation based on some fields
from the extent map I:
1106776064 = block_start (1107783680) - 1007616 (extent_offset)
extent_offset = 2207744 (start) - 1200128 (orig_start) = 1007616
The disk byte value of 1106776064 clashes with disk byte values of the
file extent items at offsets 1249280 and 1847296 in the fs tree:
item 6 key (271 EXTENT_DATA 1249280) itemoff 3568 itemsize 53
generation 20 type 2 (prealloc)
prealloc data disk byte 1106776064 nr 835584
prealloc data offset 49152 nr 598016
item 7 key (271 EXTENT_DATA 1847296) itemoff 3515 itemsize 53
generation 20 type 1 (regular)
extent data disk byte 1106776064 nr 835584
extent data offset 647168 nr 188416 ram 835584
extent compression 0 (none)
item 8 key (271 EXTENT_DATA 2035712) itemoff 3462 itemsize 53
generation 20 type 1 (regular)
extent data disk byte 1107611648 nr 245760
extent data offset 0 nr 172032 ram 245760
extent compression 0 (none)
item 9 key (271 EXTENT_DATA 2207744) itemoff 3409 itemsize 53
generation 20 type 2 (prealloc)
prealloc data disk byte 1107611648 nr 245760
prealloc data offset 172032 nr 73728
Instead of the disk byte value of 1106776064, the value of 1107611648
should have been logged. Also the data offset value should have been
172032 and not 1007616.
After a log replay we end up getting two extent items in the extent tree
with different lengths, one of 835584, which is correct and existed
before the log replay, and another one of 1032192 which is wrong and is
based on the logged file extent item:
item 12 key (1106776064 EXTENT_ITEM 835584) itemoff 3406 itemsize 53
refs 2 gen 15 flags DATA
extent data backref root 5 objectid 271 offset 1200128 count 2
item 13 key (1106776064 EXTENT_ITEM 1032192) itemoff 3353 itemsize 53
refs 1 gen 22 flags DATA
extent data backref root 5 objectid 271 offset 1200128 count 1
Obviously this leads to many problems and a filesystem check reports many
errors:
(...)
checking extents
Extent back ref already exists for 1106776064 parent 0 root 5 owner 271 offset 1200128 num_refs 1
extent item 1106776064 has multiple extent items
ref mismatch on [1106776064 835584] extent item 2, found 3
Incorrect local backref count on 1106776064 root 5 owner 271 offset 1200128 found 2 wanted 1 back 0x55b1d0ad7680
Backref 1106776064 root 5 owner 271 offset 1200128 num_refs 0 not found in extent tree
Incorrect local backref count on 1106776064 root 5 owner 271 offset 1200128 found 1 wanted 0 back 0x55b1d0ad4e70
Backref bytes do not match extent backref, bytenr=1106776064, ref bytes=835584, backref bytes=1032192
backpointer mismatch on [1106776064 835584]
checking free space cache
block group 1103101952 has wrong amount of free space
failed to load free space cache for block group 1103101952
checking fs roots
(...)
So fix this by logging the prealloc extents beyond the inode's i_size
based on searches in the subvolume tree instead of the extent maps.
Fixes: 471d557afed1 ("Btrfs: fix loss of prealloc extents past i_size after fsync log replay")
CC: stable@vger.kernel.org # 4.14+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Disabling pm runtime at probe is not sufficient to get BAM working
on remotely controller instances. pm_runtime_get_sync() would return
-EACCES in such cases.
So check if runtime pm is enabled before returning error from bam functions.
Fixes: 5b4a68952a89 ("dmaengine: qcom: bam_dma: disable runtime pm on remote controlled")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
stub_probe() calls put_busid_priv() in an error path when device isn't
found in the busid_table. Fix it by making put_busid_priv() safe to be
called with null struct bus_id_priv pointer.
This problem happens when "usbip bind" is run without loading usbip_host
driver and then running modprobe. The first failed bind attempt unbinds
the device from the original driver and when usbip_host is modprobed,
stub_probe() runs and doesn't find the device in its busid table and calls
put_busid_priv(0 with null bus_id_priv pointer.
usbip-host 3-10.2: 3-10.2 is not in match_busid table... skip!
[ 367.359679] =====================================
[ 367.359681] WARNING: bad unlock balance detected!
[ 367.359683] 4.17.0-rc4+ #5 Not tainted
[ 367.359685] -------------------------------------
[ 367.359688] modprobe/2768 is trying to release lock (
[ 367.359689]
==================================================================
[ 367.359696] BUG: KASAN: null-ptr-deref in print_unlock_imbalance_bug+0x99/0x110
[ 367.359699] Read of size 8 at addr 0000000000000058 by task modprobe/2768
[ 367.359705] CPU: 4 PID: 2768 Comm: modprobe Not tainted 4.17.0-rc4+ #5
Fixes: 22076557b07c ("usbip: usbip_host: fix NULL-ptr deref and use-after-free errors") in usb-linus
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is a comment here which says that DIV_ROUND_UP() and that's where
the problem comes from. Say you pick:
args->bpp = UINT_MAX - 7;
args->width = 4;
args->height = 1;
The integer overflow in DIV_ROUND_UP() means "cpp" is UINT_MAX / 8 and
because of how we picked args->width that means cpp < UINT_MAX / 4.
I've fixed it by preventing the integer overflow in DIV_ROUND_UP(). I
removed the check for !cpp because it's not possible after this change.
I also changed all the 0xffffffffU references to U32_MAX.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180516140026.GA19340@mwanda
|
John Stultz
Niklas Cassel
Linus Torvalds
Russell King
Borislav Petkov
Masami Hiramatsu
Łukasz Stelmach
Dmitry Safonov
Josh Poimboeuf
Mark Rutland
Tetsuo Handa
Pavel Tatashin
Shuah Khan (Samsung OSG)
Ross Zwisler
Souptick Joarder
Matthew Wilcox
Darren Hart
Helge Deller
Sebastian Andrzej Siewior
Mathieu Malaterre
Thomas Gleixner
Michael S. Tsirkin
Willy Tarreau
Coly Li
Nicholas Piggin
Pierre-Yves MORDRET
Anand Jain
Nikolay Borisov
Liu Bo
Misono Tomohiro
Filipe Manana
Srinivas Kandagatla
Dan Carpenter