aboutsummaryrefslogtreecommitdiffstatshomepage
path: root/tools/perf/scripts/python/export-to-postgresql.py (unfollow)
AgeCommit message (Collapse)AuthorFilesLines
2016-11-01net: qcom/emac: use correct value for SGMII_LN_UCDR_SO_GAIN_MODE0Timur Tabi1-1/+1
The documentation says that SGMII_LN_UCDR_SO_GAIN_MODE0 should be set to 0, not 6, on the Qualcomm Technologies QDF2432. Signed-off-by: Timur Tabi <timur@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-01drivers: net: xgene: fix: Coalescing values for v2 hardwareIyappan Subramanian2-5/+9
Changing the interrupt trigger region id to 2 and the corresponding threshold set0/set1 values to 8/16. Signed-off-by: Iyappan Subramanian <isubramanian@apm.com> Signed-off-by: Toan Le <toanle@apm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-01drivers: net: xgene: fix: Disable coalescing on v1 hardwareIyappan Subramanian2-13/+2
Since ethernet v1 hardware has a bug related to coalescing, disabling this feature. Signed-off-by: Iyappan Subramanian <isubramanian@apm.com> Signed-off-by: Toan Le <toanle@apm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-31bgmac: stop clearing DMA receive control register right after it is setAndy Gospodarek1-1/+4
Current bgmac code initializes some DMA settings in the receive control register for some hardware and then immediately clears those settings. Not clearing those settings results in ~420Mbps *improvement* in throughput; this system can now receive frames at line-rate on Broadcom 5871x hardware compared to ~520Mbps today. I also tested a few other values but found there to be no discernible difference in CPU utilization even if burst size and prefetching values are different. On the hardware tested there was no need to keep the code that cleared all but bits 16-17, but since there is a wide variety of hardware that used this driver (I did not look at all hardware docs for hardware using this IP block), I find it wise to move this call up and clear bits just after reading the default value from the hardware rather than completely removing it. This is a good candidate for -stable >=3.14 since that is when the code that was supposed to improve performance (but did not) was introduced. Signed-off-by: Andy Gospodarek <gospo@broadcom.com> Fixes: 56ceecde1f29 ("bgmac: initialize the DMA controller of core...") Cc: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-31sctp: hold transport instead of assoc when lookup assoc in rx pathXin Long3-18/+18
Prior to this patch, in rx path, before calling lock_sock, it needed to hold assoc when got it by __sctp_lookup_association, in case other place would free/put assoc. But in __sctp_lookup_association, it lookup and hold transport, then got assoc by transport->assoc, then hold assoc and put transport. It means it didn't hold transport, yet it was returned and later on directly assigned to chunk->transport. Without the protection of sock lock, the transport may be freed/put by other places, which would cause a use-after-free issue. This patch is to fix this issue by holding transport instead of assoc. As holding transport can make sure to access assoc is also safe, and actually it looks up assoc by searching transport rhashtable, to hold transport here makes more sense. Note that the function will be renamed later on on another patch. Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-31sctp: return back transport in __sctp_rcv_init_lookupXin Long1-2/+1
Prior to this patch, it used a local variable to save the transport that is looked up by __sctp_lookup_association(), and didn't return it back. But in sctp_rcv, it is used to initialize chunk->transport. So when hitting this, even if it found the transport, it was still initializing chunk->transport with null instead. This patch is to return the transport back through transport pointer that is from __sctp_rcv_lookup_harder(). Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-31sctp: hold transport instead of assoc in sctp_diagXin Long1-4/+1
In sctp_transport_lookup_process(), Commit 1cceda784980 ("sctp: fix the issue sctp_diag uses lock_sock in rcu_read_lock") moved cb() out of rcu lock, but it put transport and hold assoc instead, and ignore that cb() still uses transport. It may cause a use-after-free issue. This patch is to hold transport instead of assoc there. Fixes: 1cceda784980 ("sctp: fix the issue sctp_diag uses lock_sock in rcu_read_lock") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-31xen-netfront: do not cast grant table reference to signed shortDongli Zhang1-2/+2
While grant reference is of type uint32_t, xen-netfront erroneously casts it to signed short in BUG_ON(). This would lead to the xen domU panic during boot-up or migration when it is attached with lots of paravirtual devices. Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-31can: bcm: fix warning in bcm_connect/proc_registerOliver Hartkopp1-9/+23
Andrey Konovalov reported an issue with proc_register in bcm.c. As suggested by Cong Wang this patch adds a lock_sock() protection and a check for unsuccessful proc_create_data() in bcm_connect(). Reference: http://marc.info/?l=linux-netdev&m=147732648731237 Reported-by: Andrey Konovalov <andreyknvl@google.com> Suggested-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Tested-by: Andrey Konovalov <andreyknvl@google.com> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-10-31can: sja1000: plx_pci: Add support for Moxa CAN devicesLukas Resch1-0/+18
This patch adds support for Moxa CAN devices. Signed-off-by: Lukas Resch <l.resch@incubedit.com> Signed-off-by: Christoph Zehentner <c.zehentner@incubedit.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-10-31mlxsw: spectrum: Fix incorrect reuse of MID entriesIdo Schimmel2-8/+8
In the device, a MID entry represents a group of local ports, which can later be bound to a MDB entry. The lookup of an existing MID entry is currently done using the provided MC MAC address and VID, from the Linux bridge. However, this can result in an incorrect reuse of the same MID index in different VLAN-unaware bridges (same IP MC group and VID 0). Fix this by performing the lookup based on FID instead of VID, which is unique across different bridges. Fixes: 3a49b4fde2a1 ("mlxsw: Adding layer 2 multicast support") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Elad Raz <eladr@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-31qede: Fix statistics' strings for Tx/Rx queuesMintz, Yuval1-9/+16
When an interface is configured to use Tx/Rx-only queues, the length of the statistics would be shortened to accomodate only the statistics required per-each queue, and the values would be provided accordingly. However, the strings provided would still contain both Tx and Rx strings for each one of the queues [regardless of its configuration], which might lead to out-of-bound access when filling the buffers as well as incorrect statistics presented. Fixes: 9a4d7e86acf3 ("qede: Add support for Tx/Rx-only queues.") Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-31net: mangle zero checksum in skb_checksum_help()Eric Dumazet1-1/+1
Sending zero checksum is ok for TCP, but not for UDP. UDPv6 receiver should by default drop a frame with a 0 checksum, and UDPv4 would not verify the checksum and might accept a corrupted packet. Simply replace such checksum by 0xffff, regardless of transport. This error was caught on SIT tunnels, but seems generic. Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Willem de Bruijn <willemb@google.com> Acked-by: Maciej Żenczykowski <maze@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-31net: clear sk_err_soft in sk_clone_lock()Eric Dumazet1-0/+1
At accept() time, it is possible the parent has a non zero sk_err_soft, leftover from a prior error. Make sure we do not leave this value in the child, as it makes future getsockopt(SO_ERROR) calls quite unreliable. Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-31dctcp: avoid bogus doubling of cwnd after lossFlorian Westphal1-1/+12
If a congestion control module doesn't provide .undo_cwnd function, tcp_undo_cwnd_reduction() will set cwnd to tp->snd_cwnd = max(tp->snd_cwnd, tp->snd_ssthresh << 1); ... which makes sense for reno (it sets ssthresh to half the current cwnd), but it makes no sense for dctcp, which sets ssthresh based on the current congestion estimate. This can cause severe growth of cwnd (eventually overflowing u32). Fix this by saving last cwnd on loss and restore cwnd based on that, similar to cubic and other algorithms. Fixes: e3118e8359bb7c ("net: tcp: add DCTCP congestion control algorithm") Cc: Lawrence Brakmo <brakmo@fb.com> Cc: Andrew Shewmaker <agshew@gmail.com> Cc: Glenn Judd <glenn.judd@morganstanley.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-31ipv6: add mtu lock check in __ip6_rt_update_pmtuXin Long1-0/+3
Prior to this patch, ipv6 didn't do mtu lock check in ip6_update_pmtu. It leaded to that mtu lock doesn't really work when receiving the pkt of ICMPV6_PKT_TOOBIG. This patch is to add mtu lock check in __ip6_rt_update_pmtu just as ipv4 did in __ip_rt_update_pmtu. Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-31ipv6: Don't use ufo handling on later transformed packetsJakub Sitnicki1-1/+1
Similar to commit c146066ab802 ("ipv4: Don't use ufo handling on later transformed packets"), don't perform UFO on packets that will be IPsec transformed. To detect it we rely on the fact that headerlen in dst_entry is non-zero only for transformation bundles (xfrm_dst objects). Unwanted segmentation can be observed with a NETIF_F_UFO capable device, such as a dummy device: DEV=dum0 LEN=1493 ip li add $DEV type dummy ip addr add fc00::1/64 dev $DEV nodad ip link set $DEV up ip xfrm policy add dir out src fc00::1 dst fc00::2 \ tmpl src fc00::1 dst fc00::2 proto esp spi 1 ip xfrm state add src fc00::1 dst fc00::2 \ proto esp spi 1 enc 'aes' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b tcpdump -n -nn -i $DEV -t & socat /dev/zero,readbytes=$LEN udp6:[fc00::2]:$LEN tcpdump output before: IP6 fc00::1 > fc00::2: frag (0|1448) ESP(spi=0x00000001,seq=0x1), length 1448 IP6 fc00::1 > fc00::2: frag (1448|48) IP6 fc00::1 > fc00::2: ESP(spi=0x00000001,seq=0x2), length 88 ... and after: IP6 fc00::1 > fc00::2: frag (0|1448) ESP(spi=0x00000001,seq=0x1), length 1448 IP6 fc00::1 > fc00::2: frag (1448|80) Fixes: e89e9cf539a2 ("[IPv4/IPv6]: UFO Scatter-gather approach") Signed-off-by: Jakub Sitnicki <jkbs@redhat.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-30r8152: Fix broken RX checksums.Mark Lord1-2/+2
The r8152 driver has been broken since (approx) 3.16.xx when support was added for hardware RX checksums on newer chip versions. Symptoms include random segfaults and silent data corruption over NFS. The hardware checksum logig does not work on the VER_02 dongles I have here when used with a slow embedded system CPU. Google reveals others reporting similar issues on Raspberry Pi. So, disable hardware RX checksum support for VER_02, and fix an obvious coding error for IPV6 checksums in the same function. Because this bug results in silent data corruption, it is a good candidate for back-porting to -stable >= 3.16.xx. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-29geneve: avoid using stale geneve socket.pravin shelar1-11/+34
This patch is similar to earlier vxlan patch. Geneve device close operation frees geneve socket. This operation can race with geneve-xmit function which dereferences geneve socket. Following patch uses RCU mechanism to avoid this situation. Signed-off-by: Pravin B Shelar <pshelar@ovn.org> Acked-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-29vxlan: avoid using stale vxlan socket.pravin shelar2-32/+52
When vxlan device is closed vxlan socket is freed. This operation can race with vxlan-xmit function which dereferences vxlan socket. Following patch uses RCU mechanism to avoid this situation. Signed-off-by: Pravin B Shelar <pshelar@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-29qede: Fix out-of-bound fastpath memory accessMintz, Yuval1-2/+2
Driver allocates a shadow array for transmitted SKBs with X entries; That means valid indices are {0,...,X - 1}. [X == 8191] Problem is the driver also uses X as a mask for a producer/consumer in order to choose the right entry in the array which allows access to entry X which is out of bounds. To fix this, simply allocate X + 1 entries in the shadow array. Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-29net: phy: dp83848: add dp83822 PHY supportRoger Quadros1-0/+3
This PHY has a compatible register set with DP83848x so add support for it. Acked-by: Andrew F. Davis <afd@ti.com> Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-29enic: fix rq disableGovindarajulu Varadarajan1-9/+23
When MTU is changed from 9000 to 1500 while there is burst of inbound 9000 bytes packets, adaptor sometimes delivers 9000 bytes packets to 1500 bytes buffers. This causes memory corruption and sometimes crash. This is because of a race condition in adaptor between "RQ disable" clearing descriptor mini-cache and mini-cache valid bit being set by completion of descriptor fetch. This can result in stale RQ desc being cached and used when packets arrive. In this case, the stale descriptor have old MTU value. Solution is to write RQ->disable twice. The first write will stop any further desc fetches, allowing the second disable to clear the mini-cache valid bit without danger of a race. Also, the check for rq->running becoming 0 after writing rq->enable to 0 is not done properly. When incoming packets are flooding the interface, rq->running will pulse high for each dropped packet. Since the driver was waiting for 10us between each poll, it is possible to see rq->running = 1 1000 times in a row, even though it is not actually stuck running. This results in false failure of vnic_rq_disable(). Fix is to try more than 1000 time without delay between polls to ensure we do not miss when running goes low. In old adaptors rq->enable needs to be re-written to 0 when posted_index is reset in vnic_rq_clean() in order to keep rq->prefetch_index in sync. Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-29tipc: fix broadcast link synchronization problemJon Paul Maloy6-6/+33
In commit 2d18ac4ba745 ("tipc: extend broadcast link initialization criteria") we tried to fix a problem with the initial synchronization of broadcast link acknowledge values. Unfortunately that solution is not sufficient to solve the issue. We have seen it happen that LINK_PROTOCOL/STATE packets with a valid non-zero unicast acknowledge number may bypass BCAST_PROTOCOL initialization, NAME_DISTRIBUTOR and other STATE packets with invalid broadcast acknowledge numbers, leading to premature opening of the broadcast link. When the bypassed packets finally arrive, they are inadvertently accepted, and the already correctly initialized acknowledge number in the broadcast receive link is overwritten by the invalid (zero) value of the said packets. After this the broadcast link goes stale. We now fix this by marking the packets where we know the acknowledge value is or may be invalid, and then ignoring the acks from those. To this purpose, we claim an unused bit in the header to indicate that the value is invalid. We set the bit to 1 in the initial BCAST_PROTOCOL synchronization packet and all initial ("bulk") NAME_DISTRIBUTOR packets, plus those LINK_PROTOCOL packets sent out before the broadcast links are fully synchronized. This minor protocol update is fully backwards compatible. Reported-by: John Thompson <thompa.atl@gmail.com> Tested-by: John Thompson <thompa.atl@gmail.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-29ibmvnic: Fix missing brackets in init_sub_crq_irqsThomas Falcon1-2/+4
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-29ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt contextThomas Falcon2-11/+25
Schedule these XPORT event tasks in the shared workqueue so that IRQs are not freed in an interrupt context when sub-CRQs are released. Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-29Revert "ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context"David S. Miller2-25/+11
This reverts commit 8d7533e5aaad1c94386a8101a36b0617987966b7. It introduced kbuild failures, new version coming. Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-29arch/powerpc: Update parameters for csum_tcpudp_magic & csum_tcpudp_nofoldIvan Vecera1-8/+4
Commit 01cfbad "ipv4: Update parameters for csum_tcpudp_magic to their original types" changed parameters for csum_tcpudp_magic and csum_tcpudp_nofold for many platforms but not for PowerPC. Fixes: 01cfbad "ipv4: Update parameters for csum_tcpudp_magic to their original types" Cc: Alexander Duyck <aduyck@mirantis.com> Signed-off-by: Ivan Vecera <ivecera@redhat.com> Acked-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-29Linux 4.9-rc3Linus Torvalds1-1/+1
2016-10-29net/mlx4_en: Save slave ethtool stats commandTariq Toukan1-2/+3
Following the previous patch, as an optimization, the slave will not even bother sending the DUMP_ETH_STATS command over the comm channel. Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-29net/mlx4_en: Fix potential deadlock in port statistics flowJack Morgenstein3-16/+3
mlx4_en_DUMP_ETH_STATS took the *counter mutex* and then called the FW command, with WRAPPED attribute. As a result, the fw command is wrapped on the Hypervisor when it calls mlx4_en_DUMP_ETH_STATS. The FW command wrapper flow on the hypervisor takes the *slave_cmd_mutex* during processing. At the same time, a VF could be in the process of coming up, and could call mlx4_QUERY_FUNC_CAP. On the hypervisor, the command flow takes the *slave_cmd_mutex*, then executes mlx4_QUERY_FUNC_CAP_wrapper. mlx4_QUERY_FUNC_CAP wrapper calls mlx4_get_default_counter_index(), which takes the *counter mutex*. DEADLOCK. The fix is that the DUMP_ETH_STATS fw command should be called with the NATIVE attribute, so that on the hypervisor, this command does not enter the wrapper flow. Since the Hypervisor no longer goes through the wrapper code, we also simply return 0 in mlx4_DUMP_ETH_STATS_wrapper (i.e.the function succeeds, but the returned data will be all zeroes). No need to test if it is the Hypervisor going through the wrapper. Fixes: f9baff509f8a ("mlx4_core: Add "native" argument to mlx4_cmd ...") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-29net/mlx4: Fix firmware command timeout during interrupt testEugenia Emantayev3-36/+55
Currently interrupt test that is part of ethtool selftest runs the check over all interrupt vectors of the device. In mlx4_en package part of interrupt vectors are uninitialized since mlx4_ib doesn't exist. This causes NOP FW command to time out. Change logic to test current port interrupt vectors only. Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-29net/mlx4_core: Do not access comm channel if it has not yet been initializedJack Morgenstein1-0/+9
In the Hypervisor, there are several FW commands which are invoked before the comm channel is initialized (in mlx4_multi_func_init). These include MOD_STAT_CONFIG, QUERY_DEV_CAP, INIT_HCA, and others. If any of these commands fails, say with a timeout, the Hypervisor driver enters the internal error reset flow. In this flow, the driver attempts to notify all slaves via the comm channel that an internal error has occurred. Since the comm channel has not yet been initialized (i.e., mapped via ioremap), this will cause dereferencing a NULL pointer. To fix this, do not access the comm channel in the internal error flow if it has not yet been initialized. Fixes: 55ad359225b2 ("net/mlx4_core: Enable device recovery flow with SRIOV") Fixes: ab9c17a009ee ("mlx4_core: Modify driver initialization flow to accommodate SRIOV for Ethernet") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-29net/mlx4_en: Fix panic during rebootEugenia Emantayev1-0/+1
Fix a kernel panic that occurs as a result of an asynchronous event handled in roce_gid_mgmt: mlx4_en_get_drvinfo is called and accesses freed resources. This happens in a shutdown flow only, since pci device is destroyed while netdevice is still alive. Fixes: c27a02cd94d6 ("mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC") Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-29net/mlx4_en: Process all completions in RX rings after port goes upErez Shitrit1-0/+7
Currently there is a race between incoming traffic and initialization flow. HW is able to receive the packets after INIT_PORT is done and unicast steering is configured. Before we set priv->port_up NAPI is not scheduled and receive queues become full. Therefore we never get new interrupts about the completions. This issue could happen if running heavy traffic during bringing port up. The resolution is to schedule NAPI once port_up is set. If receive queues were full this will process all cqes and release them. Fixes: c27a02cd94d6 ("mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC") Signed-off-by: Erez Shitrit <erezsh@mellanox.com> Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-29net/mlx4_en: Resolve dividing by zero in 32-bit systemEugenia Emantayev1-1/+4
When doing roundup_pow_of_two for large enough number with bit 31, an overflow will occur and a value equal to 1 will be returned. In this case 1 will be subtracted from the return value and division by zero will be reached. Fixes: 31c128b66e5b ("net/mlx4_en: Choose time-stamping shift value according to HW frequency") Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-29net/mlx4_core: Change the default value of enable_qosMoshe Lazer1-2/+2
Change the default status of quality of service back to disabled, as it hurts performance in some cases. Fixes: 38438f7c7e8c ("net/mlx4: Set enhanced QoS support by default when ...") Signed-off-by: Moshe Lazer <moshel@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-29net/mlx4_core: Avoid setting ports to auto when only one port type is supportedMaor Gottlieb1-1/+9
When only one port type is supported, it should be read only. We reject changing requests, even to the auto sense mode. Fixes: 27bf91d6a0d5 ("mlx4_core: Add link type autosensing") Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Moshe Shemesh <moshe@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-29net/mlx4_core: Fix the resource-type enum in res tracker to conform to FW specJack Morgenstein1-1/+2
The resource type enum in the resource tracker was incorrect. RES_EQ was put in the position of RES_NPORT_ID (a FC resource). Since the remaining resources maintain their current values, and RES_EQ is not passed from slaves to the hypervisor in any FW command, this change affects only the hypervisor. Therefore, there is no backwards-compatibility issue. Fixes: 623ed84b1f95 ("mlx4_core: initial header-file changes for SRIOV support") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Moshe Shemesh <moshe@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-29rds: debug messages are enabled by defaultshamir rabinovitch2-2/+2
rds use Kconfig option called "RDS_DEBUG" to enable rds debug messages. This option cause the rds Makefile to add -DDEBUG to the rds gcc command line. When CONFIG_DYNAMIC_DEBUG is enabled, the "DEBUG" macro is used by include/linux/dynamic_debug.h to decide if dynamic debug prints should be sent by default to the kernel log. rds should not enable this macro for production builds. rds dynamic debug work as expected follow this fix. Signed-off-by: Shamir Rabinovitch <shamir.rabinovitch@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Reviewed-by: Wengang Wang <wen.gang.wang@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-29ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt contextThomas Falcon2-11/+25
Schedule these XPORT event tasks in the shared workqueue so that IRQs are not freed in an interrupt context when sub-CRQs are released. Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-29net: mv643xx_eth: Fetch the phy connection type from DTJason Gunthorpe2-4/+20
The MAC is capable of RGMII mode and that is probably a more typical connection type than GMII today (eg it is used by Marvell Reference designs for several SOCs). Let DT users specify the standard phy-connection-type = "rgmii-id"; On a phy node. Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-29Revert "hv_netvsc: report vmbus name in ethtool"Stephen Hemminger2-11/+0
This reverts commit e3f74b841d48 ("hv_netvsc: report vmbus name in ethtool")' because of problem introduced by commit f9a56e5d6a0ba ("Drivers: hv: make VMBus bus ids persistent"). This changed the format of the vmbus name and this new format is too long to fit in the bus_info field of ethtool. Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-29packet: on direct_xmit, limit tso and csum to supported devicesWillem de Bruijn2-5/+5
When transmitting on a packet socket with PACKET_VNET_HDR and PACKET_QDISC_BYPASS, validate device support for features requested in vnet_hdr. Drop TSO packets sent to devices that do not support TSO or have the feature disabled. Note that the latter currently do process those packets correctly, regardless of not advertising the feature. Because of SKB_GSO_DODGY, it is not sufficient to test device features with netif_needs_gso. Full validate_xmit_skb is needed. Switch to software checksum for non-TSO packets that request checksum offload if that device feature is unsupported or disabled. Note that similar to the TSO case, device drivers may perform checksum offload correctly even when not advertising it. When switching to software checksum, packets hit skb_checksum_help, which has two BUG_ON checksum not in linear segment. Packet sockets always allocate at least up to csum_start + csum_off + 2 as linear. Tested by running github.com/wdebruij/kerneltools/psock_txring_vnet.c ethtool -K eth0 tso off tx on psock_txring_vnet -d $dst -s $src -i eth0 -l 2000 -n 1 -q -v psock_txring_vnet -d $dst -s $src -i eth0 -l 2000 -n 1 -q -v -N ethtool -K eth0 tx off psock_txring_vnet -d $dst -s $src -i eth0 -l 1000 -n 1 -q -v -G psock_txring_vnet -d $dst -s $src -i eth0 -l 1000 -n 1 -q -v -G -N v2: - add EXPORT_SYMBOL_GPL(validate_xmit_skb_list) Fixes: d346a3fae3ff ("packet: introduce PACKET_QDISC_BYPASS socket option") Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-29net_sched actions: use nla_parse_nested()Johannes Berg1-2/+1
Use nla_parse_nested instead of open-coding the call to nla_parse() with the attribute data/len. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-29cxgb4: Fix error handling in alloc_uld_rxqs().Ganesh Goudar1-22/+18
Fix to release resources properly in error handling path of alloc_uld_rxqs(), This patch also removes unwanted arguments and avoids calling the same function twice. Fixes: 94cdb8bb993a (cxgb4: Add support for dynamic allocation of resources for ULD Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-29IB/mlx4: avoid a -Wmaybe-uninitialize warningArnd Bergmann1-2/+3
There is an old warning about mlx4_SW2HW_EQ_wrapper on x86: ethernet/mellanox/mlx4/resource_tracker.c: In function ‘mlx4_SW2HW_EQ_wrapper’: ethernet/mellanox/mlx4/resource_tracker.c:3071:10: error: ‘eq’ may be used uninitialized in this function [-Werror=maybe-uninitialized] The problem here is that gcc won't track the state of the variable across a spin_unlock. Moving the assignment out of the lock is safe here and avoids the warning. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-29ip6_tunnel: Update skb->protocol to ETH_P_IPV6 in ip6_tnl_xmit()Eli Cooper1-0/+1
This patch updates skb->protocol to ETH_P_IPV6 in ip6_tnl_xmit() when an IPv6 header is installed to a socket buffer. This is not a cosmetic change. Without updating this value, GSO packets transmitted through an ipip6 tunnel have the protocol of ETH_P_IP and skb_mac_gso_segment() will attempt to call gso_segment() for IPv4, which results in the packets being dropped. Fixes: b8921ca83eed ("ip4ip6: Support for GSO/GRO") Signed-off-by: Eli Cooper <elicooper@gmx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-29bpf: fix samples to add fake KBUILD_MODNAMEDaniel Borkmann6-0/+6
Some of the sample files are causing issues when they are loaded with tc and cls_bpf, meaning tc bails out while trying to parse the resulting ELF file as program/map/etc sections are not present, which can be easily spotted with readelf(1). Currently, BPF samples are including some of the kernel headers and mid term we should change them to refrain from this, really. When dynamic debugging is enabled, we bail out due to undeclared KBUILD_MODNAME, which is easily overlooked in the build as clang spills this along with other noisy warnings from various header includes, and llc still generates an ELF file with mentioned characteristics. For just playing around with BPF examples, this can be a bit of a hurdle to take. Just add a fake KBUILD_MODNAME as a band-aid to fix the issue, same is done in xdp*_kern samples already. Fixes: 65d472fb007d ("samples/bpf: add 'pointer to packet' tests") Fixes: 6afb1e28b859 ("samples/bpf: Add tunnel set/get tests.") Fixes: a3f74617340b ("cgroup: bpf: Add an example to do cgroup checking in BPF") Reported-by: Chandrasekar Kannan <ckannan@console.to> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-29inet: Fix missing return value in inet6_hashCraig Gallek1-2/+4
As part of a series to implement faster SO_REUSEPORT lookups, commit 086c653f5862 ("sock: struct proto hash function may error") added return values to protocol hash functions and commit 496611d7b5ea ("inet: create IPv6-equivalent inet_hash function") implemented a new hash function for IPv6. However, the latter does not respect the former's convention. This properly propagates the hash errors in the IPv6 case. Fixes: 496611d7b5ea ("inet: create IPv6-equivalent inet_hash function") Reported-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: Craig Gallek <kraig@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.