| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Explicitly set 'rc' (return code), before jumping to the
unlock and return path.
By not having any code depend on that 'rc' remains at
it's initial value of -EINVAL, then we can re-use 'rc' for
the return code of function calls in subsequent patches.
Only compile tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Donald has been contributing to YNL a lot. Let's create a dedicated
MAINTAINERS entry and add make his involvement official :)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The UMAC_CMD register is written from different execution
contexts and has insufficient synchronization protections to
prevent possible corruption. Of particular concern are the
acceses from the phy_device delayed work context used by the
adjust_link call and the BH context that may be used by the
ndo_set_rx_mode call.
A spinlock is added to the driver to protect contended register
accesses (i.e. reg_lock) and it is used to synchronize accesses
to UMAC_CMD.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Cc: stable@vger.kernel.org
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ndo_set_rx_mode function is synchronized with the
netif_addr_lock spinlock and BHs disabled. Since this
function is also invoked directly from the driver the
same synchronization should be applied.
Fixes: 72f96347628e ("net: bcmgenet: set Rx mode before starting netif")
Cc: stable@vger.kernel.org
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The EXT_RGMII_OOB_CTRL register can be written from different
contexts. It is predominantly written from the adjust_link
handler which is synchronized by the phydev->lock, but can
also be written from a different context when configuring the
mii in bcmgenet_mii_config().
The chances of contention are quite low, but it is conceivable
that adjust_link could occur during resume when WoL is enabled
so use the phydev->lock synchronizer in bcmgenet_mii_config()
to be sure.
Fixes: afe3f907d20f ("net: bcmgenet: power on MII block for all MII modes")
Cc: stable@vger.kernel.org
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix extract_user_to_sg() so that it will break out of the loop if
iov_iter_extract_pages() returns 0 rather than looping around forever.
[Note that I've included two fixes lines as the function got moved to a
different file and renamed]
Fixes: 85dd2c8ff368 ("netfs: Add a function to extract a UBUF or IOVEC into a BVEC iterator")
Fixes: f5f82cd18732 ("Move netfs_extract_iter_to_sg() to lib/scatterlist.c")
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Jeff Layton <jlayton@kernel.org>
cc: Steve French <sfrench@samba.org>
cc: Herbert Xu <herbert@gondor.apana.org.au>
cc: netfs@lists.linux.dev
Link: https://lore.kernel.org/r/1967121.1714034372@warthog.procyon.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The vsyscall is a legacy API for fast execution of system calls. It maps
a page at address VSYSCALL_ADDR into the userspace program. This address
is in the top 10MB of the address space:
ffffffffff600000 - ffffffffff600fff | 4 kB | legacy vsyscall ABI
The last commit fixes the x86-64 BPF JIT to skip accessing addresses in
this memory region. Add this address to bpf_testmod_return_ptr() so we
can make sure that it is fixed.
After this change and without the previous commit, subprogs_extable
selftest will crash the kernel.
Signed-off-by: Puranjay Mohan <puranjay@kernel.org>
Link: https://lore.kernel.org/r/20240424100210.11982-4-puranjay@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
When a load is marked PROBE_MEM - e.g. due to PTR_UNTRUSTED access - the
address being loaded from is not necessarily valid. The BPF jit sets up
exception handlers for each such load which catch page faults and 0 out
the destination register.
If the address for the load is outside kernel address space, the load
will escape the exception handling and crash the kernel. To prevent this
from happening, the emits some instruction to verify that addr is > end
of userspace addresses.
x86 has a legacy vsyscall ABI where a page at address 0xffffffffff600000
is mapped with user accessible permissions. The addresses in this page
are considered userspace addresses by the fault handler. Therefore, a
BPF program accessing this page will crash the kernel.
This patch fixes the runtime checks to also check that the PROBE_MEM
address is below VSYSCALL_ADDR.
Example BPF program:
SEC("fentry/tcp_v4_connect")
int BPF_PROG(fentry_tcp_v4_connect, struct sock *sk)
{
*(volatile unsigned long *)&sk->sk_tsq_flags;
return 0;
}
BPF Assembly:
0: (79) r1 = *(u64 *)(r1 +0)
1: (79) r1 = *(u64 *)(r1 +344)
2: (b7) r0 = 0
3: (95) exit
x86-64 JIT
==========
BEFORE AFTER
------ -----
0: nopl 0x0(%rax,%rax,1) 0: nopl 0x0(%rax,%rax,1)
5: xchg %ax,%ax 5: xchg %ax,%ax
7: push %rbp 7: push %rbp
8: mov %rsp,%rbp 8: mov %rsp,%rbp
b: mov 0x0(%rdi),%rdi b: mov 0x0(%rdi),%rdi
-------------------------------------------------------------------------------
f: movabs $0x100000000000000,%r11 f: movabs $0xffffffffff600000,%r10
19: add $0x2a0,%rdi 19: mov %rdi,%r11
20: cmp %r11,%rdi 1c: add $0x2a0,%r11
23: jae 0x0000000000000029 23: sub %r10,%r11
25: xor %edi,%edi 26: movabs $0x100000000a00000,%r10
27: jmp 0x000000000000002d 30: cmp %r10,%r11
29: mov 0x0(%rdi),%rdi 33: ja 0x0000000000000039
--------------------------------\ 35: xor %edi,%edi
2d: xor %eax,%eax \ 37: jmp 0x0000000000000040
2f: leave \ 39: mov 0x2a0(%rdi),%rdi
30: ret \--------------------------------------------
40: xor %eax,%eax
42: leave
43: ret
Signed-off-by: Puranjay Mohan <puranjay@kernel.org>
Link: https://lore.kernel.org/r/20240424100210.11982-3-puranjay@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
With BPF_PROBE_MEM, BPF allows de-referencing an untrusted pointer. To
thwart invalid memory accesses, the JITs add an exception table entry
for all such accesses. But in case the src_reg + offset is a userspace
address, the BPF program might read that memory if the user has
mapped it.
Make the verifier add guard instructions around such memory accesses and
skip the load if the address falls into the userspace region.
The JITs need to implement bpf_arch_uaddress_limit() to define where
the userspace addresses end for that architecture or TASK_SIZE is taken
as default.
The implementation is as follows:
REG_AX = SRC_REG
if(offset)
REG_AX += offset;
REG_AX >>= 32;
if (REG_AX <= (uaddress_limit >> 32))
DST_REG = 0;
else
DST_REG = *(size *)(SRC_REG + offset);
Comparing just the upper 32 bits of the load address with the upper
32 bits of uaddress_limit implies that the values are being aligned down
to a 4GB boundary before comparison.
The above means that all loads with address <= uaddress_limit + 4GB are
skipped. This is acceptable because there is a large hole (much larger
than 4GB) between userspace and kernel space memory, therefore a
correctly functioning BPF program should not access this 4GB memory
above the userspace.
Let's analyze what this patch does to the following fentry program
dereferencing an untrusted pointer:
SEC("fentry/tcp_v4_connect")
int BPF_PROG(fentry_tcp_v4_connect, struct sock *sk)
{
*(volatile long *)sk;
return 0;
}
BPF Program before | BPF Program after
------------------ | -----------------
0: (79) r1 = *(u64 *)(r1 +0) 0: (79) r1 = *(u64 *)(r1 +0)
-----------------------------------------------------------------------
1: (79) r1 = *(u64 *)(r1 +0) --\ 1: (bf) r11 = r1
----------------------------\ \ 2: (77) r11 >>= 32
2: (b7) r0 = 0 \ \ 3: (b5) if r11 <= 0x8000 goto pc+2
3: (95) exit \ \-> 4: (79) r1 = *(u64 *)(r1 +0)
\ 5: (05) goto pc+1
\ 6: (b7) r1 = 0
\--------------------------------------
7: (b7) r0 = 0
8: (95) exit
As you can see from above, in the best case (off=0), 5 extra instructions
are emitted.
Now, we analyze the same program after it has gone through the JITs of
ARM64 and RISC-V architectures. We follow the single load instruction
that has the untrusted pointer and see what instrumentation has been
added around it.
x86-64 JIT
==========
JIT's Instrumentation
(upstream)
---------------------
0: nopl 0x0(%rax,%rax,1)
5: xchg %ax,%ax
7: push %rbp
8: mov %rsp,%rbp
b: mov 0x0(%rdi),%rdi
---------------------------------
f: movabs $0x800000000000,%r11
19: cmp %r11,%rdi
1c: jb 0x000000000000002a
1e: mov %rdi,%r11
21: add $0x0,%r11
28: jae 0x000000000000002e
2a: xor %edi,%edi
2c: jmp 0x0000000000000032
2e: mov 0x0(%rdi),%rdi
---------------------------------
32: xor %eax,%eax
34: leave
35: ret
The x86-64 JIT already emits some instructions to protect against user
memory access. This patch doesn't make any changes for the x86-64 JIT.
ARM64 JIT
=========
No Intrumentation Verifier's Instrumentation
(upstream) (This patch)
----------------- --------------------------
0: add x9, x30, #0x0 0: add x9, x30, #0x0
4: nop 4: nop
8: paciasp 8: paciasp
c: stp x29, x30, [sp, #-16]! c: stp x29, x30, [sp, #-16]!
10: mov x29, sp 10: mov x29, sp
14: stp x19, x20, [sp, #-16]! 14: stp x19, x20, [sp, #-16]!
18: stp x21, x22, [sp, #-16]! 18: stp x21, x22, [sp, #-16]!
1c: stp x25, x26, [sp, #-16]! 1c: stp x25, x26, [sp, #-16]!
20: stp x27, x28, [sp, #-16]! 20: stp x27, x28, [sp, #-16]!
24: mov x25, sp 24: mov x25, sp
28: mov x26, #0x0 28: mov x26, #0x0
2c: sub x27, x25, #0x0 2c: sub x27, x25, #0x0
30: sub sp, sp, #0x0 30: sub sp, sp, #0x0
34: ldr x0, [x0] 34: ldr x0, [x0]
--------------------------------------------------------------------------------
38: ldr x0, [x0] ----------\ 38: add x9, x0, #0x0
-----------------------------------\\ 3c: lsr x9, x9, #32
3c: mov x7, #0x0 \\ 40: cmp x9, #0x10, lsl #12
40: mov sp, sp \\ 44: b.ls 0x0000000000000050
44: ldp x27, x28, [sp], #16 \\--> 48: ldr x0, [x0]
48: ldp x25, x26, [sp], #16 \ 4c: b 0x0000000000000054
4c: ldp x21, x22, [sp], #16 \ 50: mov x0, #0x0
50: ldp x19, x20, [sp], #16 \---------------------------------------
54: ldp x29, x30, [sp], #16 54: mov x7, #0x0
58: add x0, x7, #0x0 58: mov sp, sp
5c: autiasp 5c: ldp x27, x28, [sp], #16
60: ret 60: ldp x25, x26, [sp], #16
64: nop 64: ldp x21, x22, [sp], #16
68: ldr x10, 0x0000000000000070 68: ldp x19, x20, [sp], #16
6c: br x10 6c: ldp x29, x30, [sp], #16
70: add x0, x7, #0x0
74: autiasp
78: ret
7c: nop
80: ldr x10, 0x0000000000000088
84: br x10
There are 6 extra instructions added in ARM64 in the best case. This will
become 7 in the worst case (off != 0).
RISC-V JIT (RISCV_ISA_C Disabled)
==========
No Intrumentation Verifier's Instrumentation
(upstream) (This patch)
----------------- --------------------------
0: nop 0: nop
4: nop 4: nop
8: li a6, 33 8: li a6, 33
c: addi sp, sp, -16 c: addi sp, sp, -16
10: sd s0, 8(sp) 10: sd s0, 8(sp)
14: addi s0, sp, 16 14: addi s0, sp, 16
18: ld a0, 0(a0) 18: ld a0, 0(a0)
---------------------------------------------------------------
1c: ld a0, 0(a0) --\ 1c: mv t0, a0
--------------------------\ \ 20: srli t0, t0, 32
20: li a5, 0 \ \ 24: lui t1, 4096
24: ld s0, 8(sp) \ \ 28: sext.w t1, t1
28: addi sp, sp, 16 \ \ 2c: bgeu t1, t0, 12
2c: sext.w a0, a5 \ \--> 30: ld a0, 0(a0)
30: ret \ 34: j 8
\ 38: li a0, 0
\------------------------------
3c: li a5, 0
40: ld s0, 8(sp)
44: addi sp, sp, 16
48: sext.w a0, a5
4c: ret
There are 7 extra instructions added in RISC-V.
Fixes: 800834285361 ("bpf, arm64: Add BPF exception tables")
Reported-by: Breno Leitao <leitao@debian.org>
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Puranjay Mohan <puranjay12@gmail.com>
Link: https://lore.kernel.org/r/20240424100210.11982-2-puranjay@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Drop the flow-hash of the skb when forwarding to the L2TP netdev.
This avoids the L2TP qdisc from using the flow-hash from the outer
packet, which is identical for every flow within the tunnel.
This does not affect every platform but is specific for the ethernet
driver. It depends on the platform including L4 information in the
flow-hash.
One such example is the Mediatek Filogic MT798x family of networking
processors.
Fixes: d9e31d17ceba ("l2tp: Add L2TP ethernet pseudowire support")
Acked-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240424171110.13701-1-mail@david-bauer.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
syzbot triggered various splats (see [0] and links) by a crafted GSO
packet of VIRTIO_NET_HDR_GSO_UDP layering the following protocols:
ETH_P_8021AD + ETH_P_NSH + ETH_P_IPV6 + IPPROTO_UDP
NSH can encapsulate IPv4, IPv6, Ethernet, NSH, and MPLS. As the inner
protocol can be Ethernet, NSH GSO handler, nsh_gso_segment(), calls
skb_mac_gso_segment() to invoke inner protocol GSO handlers.
nsh_gso_segment() does the following for the original skb before
calling skb_mac_gso_segment()
1. reset skb->network_header
2. save the original skb->{mac_heaeder,mac_len} in a local variable
3. pull the NSH header
4. resets skb->mac_header
5. set up skb->mac_len and skb->protocol for the inner protocol.
and does the following for the segmented skb
6. set ntohs(ETH_P_NSH) to skb->protocol
7. push the NSH header
8. restore skb->mac_header
9. set skb->mac_header + mac_len to skb->network_header
10. restore skb->mac_len
There are two problems in 6-7 and 8-9.
(a)
After 6 & 7, skb->data points to the NSH header, so the outer header
(ETH_P_8021AD in this case) is stripped when skb is sent out of netdev.
Also, if NSH is encapsulated by NSH + Ethernet (so NSH-Ethernet-NSH),
skb_pull() in the first nsh_gso_segment() will make skb->data point
to the middle of the outer NSH or Ethernet header because the Ethernet
header is not pulled by the second nsh_gso_segment().
(b)
While restoring skb->{mac_header,network_header} in 8 & 9,
nsh_gso_segment() does not assume that the data in the linear
buffer is shifted.
However, udp6_ufo_fragment() could shift the data and change
skb->mac_header accordingly as demonstrated by syzbot.
If this happens, even the restored skb->mac_header points to
the middle of the outer header.
It seems nsh_gso_segment() has never worked with outer headers so far.
At the end of nsh_gso_segment(), the outer header must be restored for
the segmented skb, instead of the NSH header.
To do that, let's calculate the outer header position relatively from
the inner header and set skb->{data,mac_header,protocol} properly.
[0]:
BUG: KMSAN: uninit-value in ipvlan_process_outbound drivers/net/ipvlan/ipvlan_core.c:524 [inline]
BUG: KMSAN: uninit-value in ipvlan_xmit_mode_l3 drivers/net/ipvlan/ipvlan_core.c:602 [inline]
BUG: KMSAN: uninit-value in ipvlan_queue_xmit+0xf44/0x16b0 drivers/net/ipvlan/ipvlan_core.c:668
ipvlan_process_outbound drivers/net/ipvlan/ipvlan_core.c:524 [inline]
ipvlan_xmit_mode_l3 drivers/net/ipvlan/ipvlan_core.c:602 [inline]
ipvlan_queue_xmit+0xf44/0x16b0 drivers/net/ipvlan/ipvlan_core.c:668
ipvlan_start_xmit+0x5c/0x1a0 drivers/net/ipvlan/ipvlan_main.c:222
__netdev_start_xmit include/linux/netdevice.h:4989 [inline]
netdev_start_xmit include/linux/netdevice.h:5003 [inline]
xmit_one net/core/dev.c:3547 [inline]
dev_hard_start_xmit+0x244/0xa10 net/core/dev.c:3563
__dev_queue_xmit+0x33ed/0x51c0 net/core/dev.c:4351
dev_queue_xmit include/linux/netdevice.h:3171 [inline]
packet_xmit+0x9c/0x6b0 net/packet/af_packet.c:276
packet_snd net/packet/af_packet.c:3081 [inline]
packet_sendmsg+0x8aef/0x9f10 net/packet/af_packet.c:3113
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg net/socket.c:745 [inline]
__sys_sendto+0x735/0xa10 net/socket.c:2191
__do_sys_sendto net/socket.c:2203 [inline]
__se_sys_sendto net/socket.c:2199 [inline]
__x64_sys_sendto+0x125/0x1c0 net/socket.c:2199
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xcf/0x1e0 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x63/0x6b
Uninit was created at:
slab_post_alloc_hook mm/slub.c:3819 [inline]
slab_alloc_node mm/slub.c:3860 [inline]
__do_kmalloc_node mm/slub.c:3980 [inline]
__kmalloc_node_track_caller+0x705/0x1000 mm/slub.c:4001
kmalloc_reserve+0x249/0x4a0 net/core/skbuff.c:582
__alloc_skb+0x352/0x790 net/core/skbuff.c:651
skb_segment+0x20aa/0x7080 net/core/skbuff.c:4647
udp6_ufo_fragment+0xcab/0x1150 net/ipv6/udp_offload.c:109
ipv6_gso_segment+0x14be/0x2ca0 net/ipv6/ip6_offload.c:152
skb_mac_gso_segment+0x3e8/0x760 net/core/gso.c:53
nsh_gso_segment+0x6f4/0xf70 net/nsh/nsh.c:108
skb_mac_gso_segment+0x3e8/0x760 net/core/gso.c:53
__skb_gso_segment+0x4b0/0x730 net/core/gso.c:124
skb_gso_segment include/net/gso.h:83 [inline]
validate_xmit_skb+0x107f/0x1930 net/core/dev.c:3628
__dev_queue_xmit+0x1f28/0x51c0 net/core/dev.c:4343
dev_queue_xmit include/linux/netdevice.h:3171 [inline]
packet_xmit+0x9c/0x6b0 net/packet/af_packet.c:276
packet_snd net/packet/af_packet.c:3081 [inline]
packet_sendmsg+0x8aef/0x9f10 net/packet/af_packet.c:3113
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg net/socket.c:745 [inline]
__sys_sendto+0x735/0xa10 net/socket.c:2191
__do_sys_sendto net/socket.c:2203 [inline]
__se_sys_sendto net/socket.c:2199 [inline]
__x64_sys_sendto+0x125/0x1c0 net/socket.c:2199
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xcf/0x1e0 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x63/0x6b
CPU: 1 PID: 5101 Comm: syz-executor421 Not tainted 6.8.0-rc5-syzkaller-00297-gf2e367d6ad3b #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/25/2024
Fixes: c411ed854584 ("nsh: add GSO support")
Reported-and-tested-by: syzbot+42a0dc856239de4de60e@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=42a0dc856239de4de60e
Reported-and-tested-by: syzbot+c298c9f0e46a3c86332b@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=c298c9f0e46a3c86332b
Link: https://lore.kernel.org/netdev/20240415222041.18537-1-kuniyu@amazon.com/
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20240424023549.21862-1-kuniyu@amazon.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
We try to access count + 1 byte from userspace with memdup_user(buffer,
count + 1). However, the userspace only provides buffer of count bytes and
only these count bytes are verified to be okay to access. To ensure the
copied buffer is NUL terminated, we use memdup_user_nul instead.
Fixes: 3a2eb515d136 ("octeontx2-af: Fix an off by one in rvu_dbg_qsize_write()")
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Link: https://lore.kernel.org/r/20240424-fix-oob-read-v2-6-f1f1b53a10f4@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, we allocate a nbytes-sized kernel buffer and copy nbytes from
userspace to that buffer. Later, we use sscanf on this buffer but we don't
ensure that the string is terminated inside the buffer, this can lead to
OOB read when using sscanf. Fix this issue by using memdup_user_nul
instead of memdup_user.
Fixes: 7afc5dbde091 ("bna: Add debugfs interface.")
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Link: https://lore.kernel.org/r/20240424-fix-oob-read-v2-2-f1f1b53a10f4@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, we allocate a count-sized kernel buffer and copy count bytes
from userspace to that buffer. Later, we use sscanf on this buffer but we
don't ensure that the string is terminated inside the buffer, this can lead
to OOB read when using sscanf. Fix this issue by using memdup_user_nul
instead of memdup_user.
Fixes: 96a9a9341cda ("ice: configure FW logging")
Fixes: 73671c3162c8 ("ice: enable FW logging")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Link: https://lore.kernel.org/r/20240424-fix-oob-read-v2-1-f1f1b53a10f4@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
syzbot reported a lockdep splat regarding unix_gc_lock and
unix_state_lock().
One is called from recvmsg() for a connected socket, and another
is called from GC for TCP_LISTEN socket.
So, the splat is false-positive.
Let's add a dedicated lock class for the latter to suppress the splat.
Note that this change is not necessary for net-next.git as the issue
is only applied to the old GC impl.
[0]:
WARNING: possible circular locking dependency detected
6.9.0-rc5-syzkaller-00007-g4d2008430ce8 #0 Not tainted
-----------------------------------------------------
kworker/u8:1/11 is trying to acquire lock:
ffff88807cea4e70 (&u->lock){+.+.}-{2:2}, at: spin_lock include/linux/spinlock.h:351 [inline]
ffff88807cea4e70 (&u->lock){+.+.}-{2:2}, at: __unix_gc+0x40e/0xf70 net/unix/garbage.c:302
but task is already holding lock:
ffffffff8f6ab638 (unix_gc_lock){+.+.}-{2:2}, at: spin_lock include/linux/spinlock.h:351 [inline]
ffffffff8f6ab638 (unix_gc_lock){+.+.}-{2:2}, at: __unix_gc+0x117/0xf70 net/unix/garbage.c:261
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (unix_gc_lock){+.+.}-{2:2}:
lock_acquire+0x1ed/0x550 kernel/locking/lockdep.c:5754
__raw_spin_lock include/linux/spinlock_api_smp.h:133 [inline]
_raw_spin_lock+0x2e/0x40 kernel/locking/spinlock.c:154
spin_lock include/linux/spinlock.h:351 [inline]
unix_notinflight+0x13d/0x390 net/unix/garbage.c:140
unix_detach_fds net/unix/af_unix.c:1819 [inline]
unix_destruct_scm+0x221/0x350 net/unix/af_unix.c:1876
skb_release_head_state+0x100/0x250 net/core/skbuff.c:1188
skb_release_all net/core/skbuff.c:1200 [inline]
__kfree_skb net/core/skbuff.c:1216 [inline]
kfree_skb_reason+0x16d/0x3b0 net/core/skbuff.c:1252
kfree_skb include/linux/skbuff.h:1262 [inline]
manage_oob net/unix/af_unix.c:2672 [inline]
unix_stream_read_generic+0x1125/0x2700 net/unix/af_unix.c:2749
unix_stream_splice_read+0x239/0x320 net/unix/af_unix.c:2981
do_splice_read fs/splice.c:985 [inline]
splice_file_to_pipe+0x299/0x500 fs/splice.c:1295
do_splice+0xf2d/0x1880 fs/splice.c:1379
__do_splice fs/splice.c:1436 [inline]
__do_sys_splice fs/splice.c:1652 [inline]
__se_sys_splice+0x331/0x4a0 fs/splice.c:1634
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xf5/0x240 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
-> #0 (&u->lock){+.+.}-{2:2}:
check_prev_add kernel/locking/lockdep.c:3134 [inline]
check_prevs_add kernel/locking/lockdep.c:3253 [inline]
validate_chain+0x18cb/0x58e0 kernel/locking/lockdep.c:3869
__lock_acquire+0x1346/0x1fd0 kernel/locking/lockdep.c:5137
lock_acquire+0x1ed/0x550 kernel/locking/lockdep.c:5754
__raw_spin_lock include/linux/spinlock_api_smp.h:133 [inline]
_raw_spin_lock+0x2e/0x40 kernel/locking/spinlock.c:154
spin_lock include/linux/spinlock.h:351 [inline]
__unix_gc+0x40e/0xf70 net/unix/garbage.c:302
process_one_work kernel/workqueue.c:3254 [inline]
process_scheduled_works+0xa10/0x17c0 kernel/workqueue.c:3335
worker_thread+0x86d/0xd70 kernel/workqueue.c:3416
kthread+0x2f0/0x390 kernel/kthread.c:388
ret_from_fork+0x4b/0x80 arch/x86/kernel/process.c:147
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(unix_gc_lock);
lock(&u->lock);
lock(unix_gc_lock);
lock(&u->lock);
*** DEADLOCK ***
3 locks held by kworker/u8:1/11:
#0: ffff888015089148 ((wq_completion)events_unbound){+.+.}-{0:0}, at: process_one_work kernel/workqueue.c:3229 [inline]
#0: ffff888015089148 ((wq_completion)events_unbound){+.+.}-{0:0}, at: process_scheduled_works+0x8e0/0x17c0 kernel/workqueue.c:3335
#1: ffffc90000107d00 (unix_gc_work){+.+.}-{0:0}, at: process_one_work kernel/workqueue.c:3230 [inline]
#1: ffffc90000107d00 (unix_gc_work){+.+.}-{0:0}, at: process_scheduled_works+0x91b/0x17c0 kernel/workqueue.c:3335
#2: ffffffff8f6ab638 (unix_gc_lock){+.+.}-{2:2}, at: spin_lock include/linux/spinlock.h:351 [inline]
#2: ffffffff8f6ab638 (unix_gc_lock){+.+.}-{2:2}, at: __unix_gc+0x117/0xf70 net/unix/garbage.c:261
stack backtrace:
CPU: 0 PID: 11 Comm: kworker/u8:1 Not tainted 6.9.0-rc5-syzkaller-00007-g4d2008430ce8 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/27/2024
Workqueue: events_unbound __unix_gc
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x241/0x360 lib/dump_stack.c:114
check_noncircular+0x36a/0x4a0 kernel/locking/lockdep.c:2187
check_prev_add kernel/locking/lockdep.c:3134 [inline]
check_prevs_add kernel/locking/lockdep.c:3253 [inline]
validate_chain+0x18cb/0x58e0 kernel/locking/lockdep.c:3869
__lock_acquire+0x1346/0x1fd0 kernel/locking/lockdep.c:5137
lock_acquire+0x1ed/0x550 kernel/locking/lockdep.c:5754
__raw_spin_lock include/linux/spinlock_api_smp.h:133 [inline]
_raw_spin_lock+0x2e/0x40 kernel/locking/spinlock.c:154
spin_lock include/linux/spinlock.h:351 [inline]
__unix_gc+0x40e/0xf70 net/unix/garbage.c:302
process_one_work kernel/workqueue.c:3254 [inline]
process_scheduled_works+0xa10/0x17c0 kernel/workqueue.c:3335
worker_thread+0x86d/0xd70 kernel/workqueue.c:3416
kthread+0x2f0/0x390 kernel/kthread.c:388
ret_from_fork+0x4b/0x80 arch/x86/kernel/process.c:147
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244
</TASK>
Fixes: 47d8ac011fe1 ("af_unix: Fix garbage collector racing against connect()")
Reported-and-tested-by: syzbot+fa379358c28cc87cc307@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=fa379358c28cc87cc307
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20240424170443.9832-1-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
b44_free_rings() accesses b44::rx_buffers (and ::tx_buffers)
unconditionally, but b44::rx_buffers is only valid when the
device is up (they get allocated in b44_open(), and deallocated
again in b44_close()), any other time these are just a NULL pointers.
So if you try to change the pause params while the network interface
is disabled/administratively down, everything explodes (which likely
netifd tries to do).
Link: https://github.com/openwrt/openwrt/issues/13789
Fixes: 1da177e4c3f4 (Linux-2.6.12-rc2)
Cc: stable@vger.kernel.org
Reported-by: Peter Münster <pm@a16n.net>
Suggested-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
Tested-by: Peter Münster <pm@a16n.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Peter Münster <pm@a16n.net>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/87y192oolj.fsf@a16n.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
tls_sk_poll is called without locking the socket, and needs to read
strp->msg_ready (via tls_strp_msg_ready). Convert msg_ready to a bool
and use READ_ONCE/WRITE_ONCE where needed. The remaining reads are
only performed when the socket is locked.
Fixes: 121dca784fc0 ("tls: suppress wakeups unless we have a full record")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/r/0b7ee062319037cf86af6b317b3d72f7bfcd2e97.1713797701.git.sd@queasysnail.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In scenario where pin is registered with multiple parent pins via
dpll_pin_on_pin_register(..), all belonging to the same dpll device.
A second call to dpll_pin_on_pin_unregister(..) would cause a call trace,
as it tries to use already released registration resources (due to fix
introduced in b446631f355e). In this scenario pin was registered twice,
so resources are not yet expected to be release until each registered
pin/pin pair is unregistered.
Currently, the following crash/call trace is produced when ice driver is
removed on the system with installed E810T NIC which includes dpll device:
WARNING: CPU: 51 PID: 9155 at drivers/dpll/dpll_core.c:809 dpll_pin_ops+0x20/0x30
RIP: 0010:dpll_pin_ops+0x20/0x30
Call Trace:
? __warn+0x7f/0x130
? dpll_pin_ops+0x20/0x30
dpll_msg_add_pin_freq+0x37/0x1d0
dpll_cmd_pin_get_one+0x1c0/0x400
? __nlmsg_put+0x63/0x80
dpll_pin_event_send+0x93/0x140
dpll_pin_on_pin_unregister+0x3f/0x100
ice_dpll_deinit_pins+0xa1/0x230 [ice]
ice_remove+0xf1/0x210 [ice]
Fix by adding a parent pointer as a cookie when creating a registration,
also when searching for it. For the regular pins pass NULL, this allows to
create separated registration for each parent the pin is registered with.
Fixes: b446631f355e ("dpll: fix dpll_xa_ref_*_del() for multiple registrations")
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20240424101636.1491424-1-arkadiusz.kubalewski@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As interrupts are now requested from ravb_probe(), before calling
register_netdev(), ndev->name still contains the template "eth%d",
leading to funny names in /proc/interrupts. E.g. on R-Car E3:
89: 0 0 GICv2 93 Level eth%d:ch22:multi
90: 0 3 GICv2 95 Level eth%d:ch24:emac
91: 0 23484 GICv2 71 Level eth%d:ch0:rx_be
92: 0 0 GICv2 72 Level eth%d:ch1:rx_nc
93: 0 13735 GICv2 89 Level eth%d:ch18:tx_be
94: 0 0 GICv2 90 Level eth%d:ch19:tx_nc
Worse, on platforms with multiple RAVB instances (e.g. R-Car V4H), all
interrupts have similar names.
Fix this by using the device name instead, like is done in several other
drivers:
89: 0 0 GICv2 93 Level e6800000.ethernet:ch22:multi
90: 0 1 GICv2 95 Level e6800000.ethernet:ch24:emac
91: 0 28578 GICv2 71 Level e6800000.ethernet:ch0:rx_be
92: 0 0 GICv2 72 Level e6800000.ethernet:ch1:rx_nc
93: 0 14044 GICv2 89 Level e6800000.ethernet:ch18:tx_be
94: 0 0 GICv2 90 Level e6800000.ethernet:ch19:tx_nc
Rename the local variable dev_name, as it shadows the dev_name()
function, and pre-initialize it, to simplify the code.
Fixes: 32f012b8c01ca9fd ("net: ravb: Move getting/requesting IRQs in the probe() method")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> # on RZ/G3S
Link: https://lore.kernel.org/r/cde67b68adf115b3cf0b44c32334ae00b2fbb321.1713944647.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Clang static checker(scan-build) warning：
drivers/net/ethernet/marvell/octeontx2/af/rvu_npc.c:line 2184, column 2
Attempt to free released memory.
npc_mcam_rsrcs_deinit() has released 'mcam->counters.bmap'. Deleted this
redundant kfree() to fix this double free problem.
Fixes: dd7842878633 ("octeontx2-af: Add new devlink param to configure maximum usable NIX block LFs")
Signed-off-by: Su Hui <suhui@nfschina.com>
Reviewed-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Link: https://lore.kernel.org/r/20240424022724.144587-1-suhui@nfschina.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The CPTS, by design, captures the messageType (Sync, Delay_Req, etc.)
field from the second nibble of the PTP header which is defined in the
PTPv2 (1588-2008) specification. In the PTPv1 (1588-2002) specification
the first two bytes of the PTP header are defined as the versionType
which is always 0x0001. This means that any PTPv1 packets that are
tagged for TX timestamping by the CPTS will have their messageType set
to 0x0 which corresponds to a Sync message type. This causes issues
when a PTPv1 stack is expecting a Delay_Req (messageType: 0x1)
timestamp that never appears.
Fix this by checking if the ptp_class of the timestamped TX packet is
PTP_CLASS_V1 and then matching the PTP sequence ID to the stored
sequence ID in the skb->cb data structure. If the sequence IDs match
and the packet is of type PTPv1 then there is a chance that the
messageType has been incorrectly stored by the CPTS so overwrite the
messageType stored by the CPTS with the messageType from the skb->cb
data structure. This allows the PTPv1 stack to receive TX timestamps
for Delay_Req packets which are necessary to lock onto a PTP Leader.
Signed-off-by: Jason Reeder <jreeder@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Tested-by: Ed Trexel <ed.trexel@hp.com>
Fixes: f6bd59526ca5 ("net: ethernet: ti: introduce am654 common platform time sync driver")
Link: https://lore.kernel.org/r/20240424071626.32558-1-r-gunasekaran@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
9f74a3dfcf83 ("ice: Fix VF Reset paths when interface in a failed over
aggregate"), the ice driver has acquired the LAG mutex in ice_reset_vf().
The commit placed this lock acquisition just prior to the acquisition of
the VF configuration lock.
If ice_reset_vf() acquires the configuration lock via the ICE_VF_RESET_LOCK
flag, this could deadlock with ice_vc_cfg_qs_msg() because it always
acquires the locks in the order of the VF configuration lock and then the
LAG mutex.
Lockdep reports this violation almost immediately on creating and then
removing 2 VF:
======================================================
WARNING: possible circular locking dependency detected
6.8.0-rc6 #54 Tainted: G W O
------------------------------------------------------
kworker/60:3/6771 is trying to acquire lock:
ff40d43e099380a0 (&vf->cfg_lock){+.+.}-{3:3}, at: ice_reset_vf+0x22f/0x4d0 [ice]
but task is already holding lock:
ff40d43ea1961210 (&pf->lag_mutex){+.+.}-{3:3}, at: ice_reset_vf+0xb7/0x4d0 [ice]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&pf->lag_mutex){+.+.}-{3:3}:
__lock_acquire+0x4f8/0xb40
lock_acquire+0xd4/0x2d0
__mutex_lock+0x9b/0xbf0
ice_vc_cfg_qs_msg+0x45/0x690 [ice]
ice_vc_process_vf_msg+0x4f5/0x870 [ice]
__ice_clean_ctrlq+0x2b5/0x600 [ice]
ice_service_task+0x2c9/0x480 [ice]
process_one_work+0x1e9/0x4d0
worker_thread+0x1e1/0x3d0
kthread+0x104/0x140
ret_from_fork+0x31/0x50
ret_from_fork_asm+0x1b/0x30
-> #0 (&vf->cfg_lock){+.+.}-{3:3}:
check_prev_add+0xe2/0xc50
validate_chain+0x558/0x800
__lock_acquire+0x4f8/0xb40
lock_acquire+0xd4/0x2d0
__mutex_lock+0x9b/0xbf0
ice_reset_vf+0x22f/0x4d0 [ice]
ice_process_vflr_event+0x98/0xd0 [ice]
ice_service_task+0x1cc/0x480 [ice]
process_one_work+0x1e9/0x4d0
worker_thread+0x1e1/0x3d0
kthread+0x104/0x140
ret_from_fork+0x31/0x50
ret_from_fork_asm+0x1b/0x30
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&pf->lag_mutex);
lock(&vf->cfg_lock);
lock(&pf->lag_mutex);
lock(&vf->cfg_lock);
*** DEADLOCK ***
4 locks held by kworker/60:3/6771:
#0: ff40d43e05428b38 ((wq_completion)ice){+.+.}-{0:0}, at: process_one_work+0x176/0x4d0
#1: ff50d06e05197e58 ((work_completion)(&pf->serv_task)){+.+.}-{0:0}, at: process_one_work+0x176/0x4d0
#2: ff40d43ea1960e50 (&pf->vfs.table_lock){+.+.}-{3:3}, at: ice_process_vflr_event+0x48/0xd0 [ice]
#3: ff40d43ea1961210 (&pf->lag_mutex){+.+.}-{3:3}, at: ice_reset_vf+0xb7/0x4d0 [ice]
stack backtrace:
CPU: 60 PID: 6771 Comm: kworker/60:3 Tainted: G W O 6.8.0-rc6 #54
Hardware name:
Workqueue: ice ice_service_task [ice]
Call Trace:
<TASK>
dump_stack_lvl+0x4a/0x80
check_noncircular+0x12d/0x150
check_prev_add+0xe2/0xc50
? save_trace+0x59/0x230
? add_chain_cache+0x109/0x450
validate_chain+0x558/0x800
__lock_acquire+0x4f8/0xb40
? lockdep_hardirqs_on+0x7d/0x100
lock_acquire+0xd4/0x2d0
? ice_reset_vf+0x22f/0x4d0 [ice]
? lock_is_held_type+0xc7/0x120
__mutex_lock+0x9b/0xbf0
? ice_reset_vf+0x22f/0x4d0 [ice]
? ice_reset_vf+0x22f/0x4d0 [ice]
? rcu_is_watching+0x11/0x50
? ice_reset_vf+0x22f/0x4d0 [ice]
ice_reset_vf+0x22f/0x4d0 [ice]
? process_one_work+0x176/0x4d0
ice_process_vflr_event+0x98/0xd0 [ice]
ice_service_task+0x1cc/0x480 [ice]
process_one_work+0x1e9/0x4d0
worker_thread+0x1e1/0x3d0
? __pfx_worker_thread+0x10/0x10
kthread+0x104/0x140
? __pfx_kthread+0x10/0x10
ret_from_fork+0x31/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
To avoid deadlock, we must acquire the LAG mutex only after acquiring the
VF configuration lock. Fix the ice_reset_vf() to acquire the LAG mutex only
after we either acquire or check that the VF configuration lock is held.
Fixes: 9f74a3dfcf83 ("ice: Fix VF Reset paths when interface in a failed over aggregate")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Dave Ertman <david.m.ertman@intel.com>
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Tested-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240423182723.740401-5-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Same number of TCs doesn't imply that underlying TC configs are
same. The config could be different due to difference in number
of queues in each TC. Add utility function to determine if TC
configs are same.
Fixes: d5b33d024496 ("i40evf: add ndo_setup_tc callback to i40evf")
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Mineri Bhange <minerix.bhange@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240423182723.740401-4-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If the MFS is set below the default (0x2600), a warning message is
reported like the following :
MFS for port 1 has been set below the default: 600
This message is a bit confusing as the number shown here (600) is in
fact an hexa number: 0x600 = 1536
Without any explicit "0x" prefix, this message is read like the MFS is
set to 600 bytes.
MFS, as per MTUs, are usually expressed in decimal base.
This commit reports both current and default MFS values in decimal
so it's less confusing for end-users.
A typical warning message looks like the following :
MFS for port 1 (1536) has been set below the default (9728)
Signed-off-by: Erwan Velu <e.velu@criteo.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fixes: 3a2c6ced90e1 ("i40e: Add a check to see if MFS is set")
Link: https://lore.kernel.org/r/20240423182723.740401-3-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Issue reported by customer during SRIOV testing, call trace:
When both i40e and the i40iw driver are loaded, a warning
in check_flush_dependency is being triggered. This seems
to be because of the i40e driver workqueue is allocated with
the WQ_MEM_RECLAIM flag, and the i40iw one is not.
Similar error was encountered on ice too and it was fixed by
removing the flag. Do the same for i40e too.
[Feb 9 09:08] ------------[ cut here ]------------
[ +0.000004] workqueue: WQ_MEM_RECLAIM i40e:i40e_service_task [i40e] is
flushing !WQ_MEM_RECLAIM infiniband:0x0
[ +0.000060] WARNING: CPU: 0 PID: 937 at kernel/workqueue.c:2966
check_flush_dependency+0x10b/0x120
[ +0.000007] Modules linked in: snd_seq_dummy snd_hrtimer snd_seq
snd_timer snd_seq_device snd soundcore nls_utf8 cifs cifs_arc4
nls_ucs2_utils rdma_cm iw_cm ib_cm cifs_md4 dns_resolver netfs qrtr
rfkill sunrpc vfat fat intel_rapl_msr intel_rapl_common irdma
intel_uncore_frequency intel_uncore_frequency_common ice ipmi_ssif
isst_if_common skx_edac nfit libnvdimm x86_pkg_temp_thermal
intel_powerclamp gnss coretemp ib_uverbs rapl intel_cstate ib_core
iTCO_wdt iTCO_vendor_support acpi_ipmi mei_me ipmi_si intel_uncore
ioatdma i2c_i801 joydev pcspkr mei ipmi_devintf lpc_ich
intel_pch_thermal i2c_smbus ipmi_msghandler acpi_power_meter acpi_pad
xfs libcrc32c ast sd_mod drm_shmem_helper t10_pi drm_kms_helper sg ixgbe
drm i40e ahci crct10dif_pclmul libahci crc32_pclmul igb crc32c_intel
libata ghash_clmulni_intel i2c_algo_bit mdio dca wmi dm_mirror
dm_region_hash dm_log dm_mod fuse
[ +0.000050] CPU: 0 PID: 937 Comm: kworker/0:3 Kdump: loaded Not
tainted 6.8.0-rc2-Feb-net_dev-Qiueue-00279-gbd43c5687e05 #1
[ +0.000003] Hardware name: Intel Corporation S2600BPB/S2600BPB, BIOS
SE5C620.86B.02.01.0013.121520200651 12/15/2020
[ +0.000001] Workqueue: i40e i40e_service_task [i40e]
[ +0.000024] RIP: 0010:check_flush_dependency+0x10b/0x120
[ +0.000003] Code: ff 49 8b 54 24 18 48 8d 8b b0 00 00 00 49 89 e8 48
81 c6 b0 00 00 00 48 c7 c7 b0 97 fa 9f c6 05 8a cc 1f 02 01 e8 35 b3 fd
ff <0f> 0b e9 10 ff ff ff 80 3d 78 cc 1f 02 00 75 94 e9 46 ff ff ff 90
[ +0.000002] RSP: 0018:ffffbd294976bcf8 EFLAGS: 00010282
[ +0.000002] RAX: 0000000000000000 RBX: ffff94d4c483c000 RCX:
0000000000000027
[ +0.000001] RDX: ffff94d47f620bc8 RSI: 0000000000000001 RDI:
ffff94d47f620bc0
[ +0.000001] RBP: 0000000000000000 R08: 0000000000000000 R09:
00000000ffff7fff
[ +0.000001] R10: ffffbd294976bb98 R11: ffffffffa0be65e8 R12:
ffff94c5451ea180
[ +0.000001] R13: ffff94c5ab5e8000 R14: ffff94c5c20b6e05 R15:
ffff94c5f1330ab0
[ +0.000001] FS: 0000000000000000(0000) GS:ffff94d47f600000(0000)
knlGS:0000000000000000
[ +0.000002] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ +0.000001] CR2: 00007f9e6f1fca70 CR3: 0000000038e20004 CR4:
00000000007706f0
[ +0.000000] DR0: 0000000000000000 DR1: 0000000000000000 DR2:
0000000000000000
[ +0.000001] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7:
0000000000000400
[ +0.000001] PKRU: 55555554
[ +0.000001] Call Trace:
[ +0.000001] <TASK>
[ +0.000002] ? __warn+0x80/0x130
[ +0.000003] ? check_flush_dependency+0x10b/0x120
[ +0.000002] ? report_bug+0x195/0x1a0
[ +0.000005] ? handle_bug+0x3c/0x70
[ +0.000003] ? exc_invalid_op+0x14/0x70
[ +0.000002] ? asm_exc_invalid_op+0x16/0x20
[ +0.000006] ? check_flush_dependency+0x10b/0x120
[ +0.000002] ? check_flush_dependency+0x10b/0x120
[ +0.000002] __flush_workqueue+0x126/0x3f0
[ +0.000015] ib_cache_cleanup_one+0x1c/0xe0 [ib_core]
[ +0.000056] __ib_unregister_device+0x6a/0xb0 [ib_core]
[ +0.000023] ib_unregister_device_and_put+0x34/0x50 [ib_core]
[ +0.000020] i40iw_close+0x4b/0x90 [irdma]
[ +0.000022] i40e_notify_client_of_netdev_close+0x54/0xc0 [i40e]
[ +0.000035] i40e_service_task+0x126/0x190 [i40e]
[ +0.000024] process_one_work+0x174/0x340
[ +0.000003] worker_thread+0x27e/0x390
[ +0.000001] ? __pfx_worker_thread+0x10/0x10
[ +0.000002] kthread+0xdf/0x110
[ +0.000002] ? __pfx_kthread+0x10/0x10
[ +0.000002] ret_from_fork+0x2d/0x50
[ +0.000003] ? __pfx_kthread+0x10/0x10
[ +0.000001] ret_from_fork_asm+0x1b/0x30
[ +0.000004] </TASK>
[ +0.000001] ---[ end trace 0000000000000000 ]---
Fixes: 4d5957cbdecd ("i40e: remove WQ_UNBOUND and the task limit of our workqueue")
Signed-off-by: Sindhu Devale <sindhu.devale@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Robert Ganzynkowicz <robert.ganzynkowicz@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240423182723.740401-2-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The rx_chn->irq[] array is unsigned int but it should be signed for the
error handling to work. Also if k3_udma_glue_rx_get_irq() returns zero
then we should return -ENXIO instead of success.
Fixes: 128d5874c082 ("net: ti: icssg-prueth: Add ICSSG ethernet driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://lore.kernel.org/r/05282415-e7f4-42f3-99f8-32fde8f30936@moroto.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
mlx5 Rx flow steering and CQE handling enable the driver to be able to
update an skb's md_dst attribute as MACsec when MACsec traffic arrives when
a device is configured for offloading. Advertise this to the core stack to
take advantage of this capability.
Cc: stable@vger.kernel.org
Fixes: b7c9400cbc48 ("net/mlx5e: Implement MACsec Rx data path using MACsec skb_metadata_dst")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Benjamin Poirier <bpoirier@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/r/20240423181319.115860-5-rrameshbabu@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Can now correctly identify where the packets should be delivered by using
md_dst or its absence on devices that provide it.
This detection is not possible without device drivers that update md_dst. A
fallback pattern should be used for supporting such device drivers. This
fallback mode causes multicast messages to be cloned to both the non-macsec
and macsec ports, independent of whether the multicast message received was
encrypted over MACsec or not. Other non-macsec traffic may also fail to be
handled correctly for devices in promiscuous mode.
Link: https://lore.kernel.org/netdev/ZULRxX9eIbFiVi7v@hog/
Cc: Sabrina Dubroca <sd@queasysnail.net>
Cc: stable@vger.kernel.org
Fixes: 860ead89b851 ("net/macsec: Add MACsec skb_metadata_dst Rx Data path support")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Benjamin Poirier <bpoirier@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/r/20240423181319.115860-4-rrameshbabu@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Enable reuse of logic in eth_type_trans for determining packet type.
Suggested-by: Sabrina Dubroca <sd@queasysnail.net>
Cc: stable@vger.kernel.org
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/r/20240423181319.115860-3-rrameshbabu@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cannot know whether a Rx skb missing md_dst is intended for MACsec or not
without knowing whether the device is able to update this field during an
offload. Assume that an offload to a MACsec device cannot support updating
md_dst by default. Capable devices can advertise that they do indicate that
an skb is related to a MACsec offloaded packet using the md_dst.
Cc: Sabrina Dubroca <sd@queasysnail.net>
Cc: stable@vger.kernel.org
Fixes: 860ead89b851 ("net/macsec: Add MACsec skb_metadata_dst Rx Data path support")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Benjamin Poirier <bpoirier@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/r/20240423181319.115860-2-rrameshbabu@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The DP83869 driver sets the MII bit (needed for PHY to work in MII mode)
only if the op-mode is either DP83869_100M_MEDIA_CONVERT or
DP83869_RGMII_100_BASE.
Some drivers i.e. ICSSG support MII mode with op-mode as
DP83869_RGMII_COPPER_ETHERNET for which the MII bit is not set in dp83869
driver. As a result MII mode on ICSSG doesn't work and below log is seen.
TI DP83869 300b2400.mdio:0f: selected op-mode is not valid with MII mode
icssg-prueth icssg1-eth: couldn't connect to phy ethernet-phy@0
icssg-prueth icssg1-eth: can't phy connect port MII0
Fix this by setting MII bit for DP83869_RGMII_COPPER_ETHERNET op-mode as
well.
Fixes: 94e86ef1b801 ("net: phy: dp83869: support mii mode when rgmii strap cfg is used")
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check for table dormant flag otherwise netdev release event path tries
to unregister an already unregistered hook.
[524854.857999] ------------[ cut here ]------------
[524854.858010] WARNING: CPU: 0 PID: 3386599 at net/netfilter/core.c:501 __nf_unregister_net_hook+0x21a/0x260
[...]
[524854.858848] CPU: 0 PID: 3386599 Comm: kworker/u32:2 Not tainted 6.9.0-rc3+ #365
[524854.858869] Workqueue: netns cleanup_net
[524854.858886] RIP: 0010:__nf_unregister_net_hook+0x21a/0x260
[524854.858903] Code: 24 e8 aa 73 83 ff 48 63 43 1c 83 f8 01 0f 85 3d ff ff ff e8 98 d1 f0 ff 48 8b 3c 24 e8 8f 73 83 ff 48 63 43 1c e9 26 ff ff ff <0f> 0b 48 83 c4 18 48 c7 c7 00 68 e9 82 5b 5d 41 5c 41 5d 41 5e 41
[524854.858914] RSP: 0018:ffff8881e36d79e0 EFLAGS: 00010246
[524854.858926] RAX: 0000000000000000 RBX: ffff8881339ae790 RCX: ffffffff81ba524a
[524854.858936] RDX: dffffc0000000000 RSI: 0000000000000008 RDI: ffff8881c8a16438
[524854.858945] RBP: ffff8881c8a16438 R08: 0000000000000001 R09: ffffed103c6daf34
[524854.858954] R10: ffff8881e36d79a7 R11: 0000000000000000 R12: 0000000000000005
[524854.858962] R13: ffff8881c8a16000 R14: 0000000000000000 R15: ffff8881351b5a00
[524854.858971] FS: 0000000000000000(0000) GS:ffff888390800000(0000) knlGS:0000000000000000
[524854.858982] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[524854.858991] CR2: 00007fc9be0f16f4 CR3: 00000001437cc004 CR4: 00000000001706f0
[524854.859000] Call Trace:
[524854.859006] <TASK>
[524854.859013] ? __warn+0x9f/0x1a0
[524854.859027] ? __nf_unregister_net_hook+0x21a/0x260
[524854.859044] ? report_bug+0x1b1/0x1e0
[524854.859060] ? handle_bug+0x3c/0x70
[524854.859071] ? exc_invalid_op+0x17/0x40
[524854.859083] ? asm_exc_invalid_op+0x1a/0x20
[524854.859100] ? __nf_unregister_net_hook+0x6a/0x260
[524854.859116] ? __nf_unregister_net_hook+0x21a/0x260
[524854.859135] nf_tables_netdev_event+0x337/0x390 [nf_tables]
[524854.859304] ? __pfx_nf_tables_netdev_event+0x10/0x10 [nf_tables]
[524854.859461] ? packet_notifier+0xb3/0x360
[524854.859476] ? _raw_spin_unlock_irqrestore+0x11/0x40
[524854.859489] ? dcbnl_netdevice_event+0x35/0x140
[524854.859507] ? __pfx_nf_tables_netdev_event+0x10/0x10 [nf_tables]
[524854.859661] notifier_call_chain+0x7d/0x140
[524854.859677] unregister_netdevice_many_notify+0x5e1/0xae0
Fixes: d54725cd11a5 ("netfilter: nf_tables: support for multiple devices per netdev hook")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
I added OOM and netpoll discard counters, naively assuming that
the cpr pointer is pointing to a common completion ring.
Turns out that is usually *a* completion ring but not *the*
completion ring which bnapi->cp_ring points to. bnapi->cp_ring
is where the stats are read from, so we end up reporting 0
thru ethtool -S and qstat even though the drop events have happened.
Make 100% sure we're recording statistics in the correct structure.
Fixes: 907fd4a294db ("bnxt: count discards due to memory allocation errors")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20240424002148.3937059-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Roman reports a deadlock on unplug of a Thunderbolt docking station
containing an Intel I225 Ethernet adapter.
The root cause is that led_classdev's for LEDs on the adapter are
registered such that they're device-managed by the netdev. That
results in recursive acquisition of the rtnl_lock() mutex on unplug:
When the driver calls unregister_netdev(), it acquires rtnl_lock(),
then frees the device-managed resources. Upon unregistering the LEDs,
netdev_trig_deactivate() invokes unregister_netdevice_notifier(),
which tries to acquire rtnl_lock() again.
Avoid by using non-device-managed LED registration.
Stack trace for posterity:
schedule+0x6e/0xf0
schedule_preempt_disabled+0x15/0x20
__mutex_lock+0x2a0/0x750
unregister_netdevice_notifier+0x40/0x150
netdev_trig_deactivate+0x1f/0x60 [ledtrig_netdev]
led_trigger_set+0x102/0x330
led_classdev_unregister+0x4b/0x110
release_nodes+0x3d/0xb0
devres_release_all+0x8b/0xc0
device_del+0x34f/0x3c0
unregister_netdevice_many_notify+0x80b/0xaf0
unregister_netdev+0x7c/0xd0
igc_remove+0xd8/0x1e0 [igc]
pci_device_remove+0x3f/0xb0
Fixes: ea578703b03d ("igc: Add support for LEDs on i225/i226")
Reported-by: Roman Lozko <lozko.roma@gmail.com>
Closes: https://lore.kernel.org/r/CAEhC_B=ksywxCG_+aQqXUrGEgKq+4mqnSV8EBHOKbC3-Obj9+Q@mail.gmail.com/
Reported-by: "Marek Marczykowski-Górecki" <marmarek@invisiblethingslab.com>
Closes: https://lore.kernel.org/r/ZhRD3cOtz5i-61PB@mail-itl/
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de> # Intel i225
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240422204503.225448-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit e30cef001da259e8df354b813015d0e5acc08740.
commit 99f4570cfba1 ("clkdev: Update clkdev id usage to allow
for longer names") can fix clk_name exceed MAX_DEV_ID limits,
so this commit is meaningless.
Signed-off-by: Duanqiang Wen <duanqiangwen@net-swift.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240422084109.3201-2-duanqiangwen@net-swift.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit c644920ce9220d83e070f575a4df711741c07f07.
when register i2c dev, txgbe shorten "i2c_designware" to "i2c_dw",
will cause this i2c dev can't match platfom driver i2c_designware_platform.
Signed-off-by: Duanqiang Wen <duanqiangwen@net-swift.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240422084109.3201-1-duanqiangwen@net-swift.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The rehash delayed work is rescheduled with a delay if the number of
credits at end of the work is not negative as supposedly it means that
the migration ended. Otherwise, it is rescheduled immediately.
After "mlxsw: spectrum_acl_tcam: Fix possible use-after-free during
rehash" the above is no longer accurate as a non-negative number of
credits is no longer indicative of the migration being done. It can also
happen if the work encountered an error in which case the migration will
resume the next time the work is scheduled.
The significance of the above is that it is possible for the work to be
pending and associated with hints that were allocated when the migration
started. This leads to the hints being leaked [1] when the work is
canceled while pending as part of ACL region dismantle.
Fix by freeing the hints if hints are associated with a work that was
canceled while pending.
Blame the original commit since the reliance on not having a pending
work associated with hints is fragile.
[1]
unreferenced object 0xffff88810e7c3000 (size 256):
comm "kworker/0:16", pid 176, jiffies 4295460353
hex dump (first 32 bytes):
00 30 95 11 81 88 ff ff 61 00 00 00 00 00 00 80 .0......a.......
00 00 61 00 40 00 00 00 00 00 00 00 04 00 00 00 ..a.@...........
backtrace (crc 2544ddb9):
[<00000000cf8cfab3>] kmalloc_trace+0x23f/0x2a0
[<000000004d9a1ad9>] objagg_hints_get+0x42/0x390
[<000000000b143cf3>] mlxsw_sp_acl_erp_rehash_hints_get+0xca/0x400
[<0000000059bdb60a>] mlxsw_sp_acl_tcam_vregion_rehash_work+0x868/0x1160
[<00000000e81fd734>] process_one_work+0x59c/0xf20
[<00000000ceee9e81>] worker_thread+0x799/0x12c0
[<00000000bda6fe39>] kthread+0x246/0x300
[<0000000070056d23>] ret_from_fork+0x34/0x70
[<00000000dea2b93e>] ret_from_fork_asm+0x1a/0x30
Fixes: c9c9af91f1d9 ("mlxsw: spectrum_acl: Allow to interrupt/continue rehash work")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/0cc12ebb07c4d4c41a1265ee2c28b392ff997a86.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Both the function that migrates all the chunks within a region and the
function that migrates all the entries within a chunk call
list_first_entry() on the respective lists without checking that the
lists are not empty. This is incorrect usage of the API, which leads to
the following warning [1].
Fix by returning if the lists are empty as there is nothing to migrate
in this case.
[1]
WARNING: CPU: 0 PID: 6437 at drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c:1266 mlxsw_sp_acl_tcam_vchunk_migrate_all+0x1f1/0>
Modules linked in:
CPU: 0 PID: 6437 Comm: kworker/0:37 Not tainted 6.9.0-rc3-custom-00883-g94a65f079ef6 #39
Hardware name: Mellanox Technologies Ltd. MSN3700/VMOD0005, BIOS 5.11 01/06/2019
Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work
RIP: 0010:mlxsw_sp_acl_tcam_vchunk_migrate_all+0x1f1/0x2c0
[...]
Call Trace:
<TASK>
mlxsw_sp_acl_tcam_vregion_rehash_work+0x6c/0x4a0
process_one_work+0x151/0x370
worker_thread+0x2cb/0x3e0
kthread+0xd0/0x100
ret_from_fork+0x34/0x50
ret_from_fork_asm+0x1a/0x30
</TASK>
Fixes: 6f9579d4e302 ("mlxsw: spectrum_acl: Remember where to continue rehash migration")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/4628e9a22d1d84818e28310abbbc498e7bc31bc9.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As previously explained, the rehash delayed work migrates filters from
one region to another. This is done by iterating over all chunks (all
the filters with the same priority) in the region and in each chunk
iterating over all the filters.
When the work runs out of credits it stores the current chunk and entry
as markers in the per-work context so that it would know where to resume
the migration from the next time the work is scheduled.
Upon error, the chunk marker is reset to NULL, but without resetting the
entry markers despite being relative to it. This can result in migration
being resumed from an entry that does not belong to the chunk being
migrated. In turn, this will eventually lead to a chunk being iterated
over as if it is an entry. Because of how the two structures happen to
be defined, this does not lead to KASAN splats, but to warnings such as
[1].
Fix by creating a helper that resets all the markers and call it from
all the places the currently only reset the chunk marker. For good
measures also call it when starting a completely new rehash. Add a
warning to avoid future cases.
[1]
WARNING: CPU: 7 PID: 1076 at drivers/net/ethernet/mellanox/mlxsw/core_acl_flex_keys.c:407 mlxsw_afk_encode+0x242/0x2f0
Modules linked in:
CPU: 7 PID: 1076 Comm: kworker/7:24 Tainted: G W 6.9.0-rc3-custom-00880-g29e61d91b77b #29
Hardware name: Mellanox Technologies Ltd. MSN3700/VMOD0005, BIOS 5.11 01/06/2019
Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work
RIP: 0010:mlxsw_afk_encode+0x242/0x2f0
[...]
Call Trace:
<TASK>
mlxsw_sp_acl_atcam_entry_add+0xd9/0x3c0
mlxsw_sp_acl_tcam_entry_create+0x5e/0xa0
mlxsw_sp_acl_tcam_vchunk_migrate_all+0x109/0x290
mlxsw_sp_acl_tcam_vregion_rehash_work+0x6c/0x470
process_one_work+0x151/0x370
worker_thread+0x2cb/0x3e0
kthread+0xd0/0x100
ret_from_fork+0x34/0x50
</TASK>
Fixes: 6f9579d4e302 ("mlxsw: spectrum_acl: Remember where to continue rehash migration")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/cc17eed86b41dd829d39b07906fec074a9ce580e.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The rehash delayed work migrates filters from one region to another.
This is done by iterating over all chunks (all the filters with the same
priority) in the region and in each chunk iterating over all the
filters.
If the migration fails, the code tries to migrate the filters back to
the old region. However, the rollback itself can also fail in which case
another migration will be erroneously performed. Besides the fact that
this ping pong is not a very good idea, it also creates a problem.
Each virtual chunk references two chunks: The currently used one
('vchunk->chunk') and a backup ('vchunk->chunk2'). During migration the
first holds the chunk we want to migrate filters to and the second holds
the chunk we are migrating filters from.
The code currently assumes - but does not verify - that the backup chunk
does not exist (NULL) if the currently used chunk does not reference the
target region. This assumption breaks when we are trying to rollback a
rollback, resulting in the backup chunk being overwritten and leaked
[1].
Fix by not rolling back a failed rollback and add a warning to avoid
future cases.
[1]
WARNING: CPU: 5 PID: 1063 at lib/parman.c:291 parman_destroy+0x17/0x20
Modules linked in:
CPU: 5 PID: 1063 Comm: kworker/5:11 Tainted: G W 6.9.0-rc2-custom-00784-gc6a05c468a0b #14
Hardware name: Mellanox Technologies Ltd. MSN3700/VMOD0005, BIOS 5.11 01/06/2019
Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work
RIP: 0010:parman_destroy+0x17/0x20
[...]
Call Trace:
<TASK>
mlxsw_sp_acl_atcam_region_fini+0x19/0x60
mlxsw_sp_acl_tcam_region_destroy+0x49/0xf0
mlxsw_sp_acl_tcam_vregion_rehash_work+0x1f1/0x470
process_one_work+0x151/0x370
worker_thread+0x2cb/0x3e0
kthread+0xd0/0x100
ret_from_fork+0x34/0x50
ret_from_fork_asm+0x1a/0x30
</TASK>
Fixes: 843500518509 ("mlxsw: spectrum_acl: Do rollback as another call to mlxsw_sp_acl_tcam_vchunk_migrate_all()")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/d5edd4f4503934186ae5cfe268503b16345b4e0f.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In the rare cases when the device resources are exhausted it is likely
that the rehash delayed work will fail. An error message will be printed
whenever this happens which can be overwhelming considering the fact
that the work is per-region and that there can be hundreds of regions.
Fix by rate limiting the error message.
Fixes: e5e7962ee5c2 ("mlxsw: spectrum_acl: Implement region migration according to hints")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/c510763b2ebd25e7990d80183feff91cde593145.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The rehash delayed work migrates filters from one region to another
according to the number of available credits.
The migrated from region is destroyed at the end of the work if the
number of credits is non-negative as the assumption is that this is
indicative of migration being complete. This assumption is incorrect as
a non-negative number of credits can also be the result of a failed
migration.
The destruction of a region that still has filters referencing it can
result in a use-after-free [1].
Fix by not destroying the region if migration failed.
[1]
BUG: KASAN: slab-use-after-free in mlxsw_sp_acl_ctcam_region_entry_remove+0x21d/0x230
Read of size 8 at addr ffff8881735319e8 by task kworker/0:31/3858
CPU: 0 PID: 3858 Comm: kworker/0:31 Tainted: G W 6.9.0-rc2-custom-00782-gf2275c2157d8 #5
Hardware name: Mellanox Technologies Ltd. MSN3700/VMOD0005, BIOS 5.11 01/06/2019
Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work
Call Trace:
<TASK>
dump_stack_lvl+0xc6/0x120
print_report+0xce/0x670
kasan_report+0xd7/0x110
mlxsw_sp_acl_ctcam_region_entry_remove+0x21d/0x230
mlxsw_sp_acl_ctcam_entry_del+0x2e/0x70
mlxsw_sp_acl_atcam_entry_del+0x81/0x210
mlxsw_sp_acl_tcam_vchunk_migrate_all+0x3cd/0xb50
mlxsw_sp_acl_tcam_vregion_rehash_work+0x157/0x1300
process_one_work+0x8eb/0x19b0
worker_thread+0x6c9/0xf70
kthread+0x2c9/0x3b0
ret_from_fork+0x4d/0x80
ret_from_fork_asm+0x1a/0x30
</TASK>
Allocated by task 174:
kasan_save_stack+0x33/0x60
kasan_save_track+0x14/0x30
__kasan_kmalloc+0x8f/0xa0
__kmalloc+0x19c/0x360
mlxsw_sp_acl_tcam_region_create+0xdf/0x9c0
mlxsw_sp_acl_tcam_vregion_rehash_work+0x954/0x1300
process_one_work+0x8eb/0x19b0
worker_thread+0x6c9/0xf70
kthread+0x2c9/0x3b0
ret_from_fork+0x4d/0x80
ret_from_fork_asm+0x1a/0x30
Freed by task 7:
kasan_save_stack+0x33/0x60
kasan_save_track+0x14/0x30
kasan_save_free_info+0x3b/0x60
poison_slab_object+0x102/0x170
__kasan_slab_free+0x14/0x30
kfree+0xc1/0x290
mlxsw_sp_acl_tcam_region_destroy+0x272/0x310
mlxsw_sp_acl_tcam_vregion_rehash_work+0x731/0x1300
process_one_work+0x8eb/0x19b0
worker_thread+0x6c9/0xf70
kthread+0x2c9/0x3b0
ret_from_fork+0x4d/0x80
ret_from_fork_asm+0x1a/0x30
Fixes: c9c9af91f1d9 ("mlxsw: spectrum_acl: Allow to interrupt/continue rehash work")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/3e412b5659ec2310c5c615760dfe5eac18dd7ebd.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The rule activity update delayed work periodically traverses the list of
configured rules and queries their activity from the device.
As part of this task it accesses the entry pointed by 'ventry->entry',
but this entry can be changed concurrently by the rehash delayed work,
leading to a use-after-free [1].
Fix by closing the race and perform the activity query under the
'vregion->lock' mutex.
[1]
BUG: KASAN: slab-use-after-free in mlxsw_sp_acl_tcam_flower_rule_activity_get+0x121/0x140
Read of size 8 at addr ffff8881054ed808 by task kworker/0:18/181
CPU: 0 PID: 181 Comm: kworker/0:18 Not tainted 6.9.0-rc2-custom-00781-gd5ab772d32f7 #2
Hardware name: Mellanox Technologies Ltd. MSN3700/VMOD0005, BIOS 5.11 01/06/2019
Workqueue: mlxsw_core mlxsw_sp_acl_rule_activity_update_work
Call Trace:
<TASK>
dump_stack_lvl+0xc6/0x120
print_report+0xce/0x670
kasan_report+0xd7/0x110
mlxsw_sp_acl_tcam_flower_rule_activity_get+0x121/0x140
mlxsw_sp_acl_rule_activity_update_work+0x219/0x400
process_one_work+0x8eb/0x19b0
worker_thread+0x6c9/0xf70
kthread+0x2c9/0x3b0
ret_from_fork+0x4d/0x80
ret_from_fork_asm+0x1a/0x30
</TASK>
Allocated by task 1039:
kasan_save_stack+0x33/0x60
kasan_save_track+0x14/0x30
__kasan_kmalloc+0x8f/0xa0
__kmalloc+0x19c/0x360
mlxsw_sp_acl_tcam_entry_create+0x7b/0x1f0
mlxsw_sp_acl_tcam_vchunk_migrate_all+0x30d/0xb50
mlxsw_sp_acl_tcam_vregion_rehash_work+0x157/0x1300
process_one_work+0x8eb/0x19b0
worker_thread+0x6c9/0xf70
kthread+0x2c9/0x3b0
ret_from_fork+0x4d/0x80
ret_from_fork_asm+0x1a/0x30
Freed by task 1039:
kasan_save_stack+0x33/0x60
kasan_save_track+0x14/0x30
kasan_save_free_info+0x3b/0x60
poison_slab_object+0x102/0x170
__kasan_slab_free+0x14/0x30
kfree+0xc1/0x290
mlxsw_sp_acl_tcam_vchunk_migrate_all+0x3d7/0xb50
mlxsw_sp_acl_tcam_vregion_rehash_work+0x157/0x1300
process_one_work+0x8eb/0x19b0
worker_thread+0x6c9/0xf70
kthread+0x2c9/0x3b0
ret_from_fork+0x4d/0x80
ret_from_fork_asm+0x1a/0x30
Fixes: 2bffc5322fd8 ("mlxsw: spectrum_acl: Don't take mutex in mlxsw_sp_acl_tcam_vregion_rehash_work()")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/1fcce0a60b231ebeb2515d91022284ba7b4ffe7a.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The purpose of the rehash delayed work is to reduce the number of masks
(eRPs) used by an ACL region as the eRP bank is a global and limited
resource.
This is done in three steps:
1. Creating a new set of masks and a new ACL region which will use the
new masks and to which the existing filters will be migrated to. The
new region is assigned to 'vregion->region' and the region from which
the filters are migrated from is assigned to 'vregion->region2'.
2. Migrating all the filters from the old region to the new region.
3. Destroying the old region and setting 'vregion->region2' to NULL.
Only the second steps is performed under the 'vregion->lock' mutex
although its comments says that among other things it "Protects
consistency of region, region2 pointers".
This is problematic as the first step can race with filter insertion
from user space that uses 'vregion->region', but under the mutex.
Fix by holding the mutex across the entirety of the delayed work and not
only during the second step.
Fixes: 2bffc5322fd8 ("mlxsw: spectrum_acl: Don't take mutex in mlxsw_sp_acl_tcam_vregion_rehash_work()")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/1ec1d54edf2bad0a369e6b4fa030aba64e1f124b.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Region identifiers can be allocated both when user space tries to insert
a new tc filter and when filters are migrated from one region to another
as part of the rehash delayed work.
There is no lock protecting the bitmap from which these identifiers are
allocated from, which is racy and leads to bad parameter errors from the
device's firmware.
Fix by converting the bitmap to IDA which handles its own locking. For
consistency, do the same for the group identifiers that are part of the
same structure.
Fixes: 2bffc5322fd8 ("mlxsw: spectrum_acl: Don't take mutex in mlxsw_sp_acl_tcam_vregion_rehash_work()")
Reported-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/ce494b7940cadfe84f3e18da7785b51ef5f776e3.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since kfree_rcu, which is called in the hlist_for_each_entry_rcu traversal
of ovs_ct_limit_exit, is not part of the RCU read critical section, it
is possible that the RCU grace period will pass during the traversal and
the key will be free.
To prevent this, it should be changed to hlist_for_each_entry_safe.
Fixes: 11efd5cb04a1 ("openvswitch: Support conntrack zone limit")
Signed-off-by: Hyunwoo Kim <v4bel@theori.io>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Link: https://lore.kernel.org/r/ZiYvzQN/Ry5oeFQW@v4bel-B760M-AORUS-ELITE-AX
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It was observed in the wild that pairs of consecutive packets would leave
the IPVS with the same wrong checksum, and the issue only went away when
disabling GSO.
IPVS needs to avoid computing the SCTP checksum when using GSO.
Fixes: 90017accff61 ("sctp: Add GSO support")
Co-developed-by: Firo Yang <firo.yang@suse.com>
Signed-off-by: Ismael Luceno <iluceno@suse.de>
Tested-by: Andreas Taschner <andreas.taschner@suse.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Any return value from gpiod_get_optional() other than a pointer to a
GPIO descriptor or a NULL-pointer is an error and the driver should
abort probing. That being said: commit 56d074d26c58 ("Bluetooth: hci_qca:
don't use IS_ERR_OR_NULL() with gpiod_get_optional()") no longer sets
power_ctrl_enabled on NULL-pointer returned by
devm_gpiod_get_optional(). Restore this behavior but bail-out on errors.
While at it: also bail-out on error returned when trying to get the
"swctrl" GPIO.
Reported-by: Wren Turkal <wt@penguintechs.org>
Reported-by: Zijun Hu <quic_zijuhu@quicinc.com>
Closes: https://lore.kernel.org/linux-bluetooth/1713449192-25926-2-git-send-email-quic_zijuhu@quicinc.com/
Fixes: 56d074d26c58 ("Bluetooth: hci_qca: don't use IS_ERR_OR_NULL() with gpiod_get_optional()")
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Tested-by: Wren Turkal" <wt@penguintechs.org>
Reported-by: Wren Turkal <wt@penguintechs.org>
Reported-by: Zijun Hu <quic_zijuhu@quicinc.com>
Reviewed-by: Krzysztof Kozlowski<krzysztof.kozlowski@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Since the d883a4669a1de be introduced in v6.4, bluetooth daemon
got the following failed message of MGMT_OP_REMOVE_ADV_MONITOR
command when controller is power-off:
bluetoothd[20976]:
src/adapter.c:reset_adv_monitors_complete() Failed to reset Adv
Monitors: Failed>
Normally this situation is happened when the bluetoothd deamon
be started manually after system booting. Which means that
bluetoothd received MGMT_EV_INDEX_ADDED event after kernel
runs hci_power_off().
Base on doc/mgmt-api.txt, the MGMT_OP_REMOVE_ADV_MONITOR command
can be used when the controller is not powered. This patch changes
the code in remove_adv_monitor() to use hci_cmd_sync_submit()
instead of hci_cmd_sync_queue().
Fixes: d883a4669a1de ("Bluetooth: hci_sync: Only allow hci_cmd_sync_queue if running")
Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Cc: Manish Mandlik <mmandlik@google.com>
Cc: Archie Pusaka <apusaka@chromium.org>
Cc: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Chun-Yi Lee <jlee@suse.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Qualcomm ROME controllers can be registered from the Bluetooth line
discipline and in this case the HCI UART serdev pointer is NULL.
Add the missing sanity check to prevent a NULL-pointer dereference when
setup() is called for a non-serdev controller.
Fixes: e9b3e5b8c657 ("Bluetooth: hci_qca: only assign wakeup with serial port support")
Cc: stable@vger.kernel.org # 6.2
Cc: Zhengping Jiang <jiangzp@google.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
Asbjørn Sloth Tønnesen
Jakub Kicinski
Doug Berger
David Howells
Puranjay Mohan
Puranjay Mohan
David Bauer
Kuniyuki Iwashima
Bui Quang Minh
Peter Münster
Sabrina Dubroca
Arkadiusz Kubalewski
Geert Uytterhoeven
Su Hui
Jason Reeder
Jacob Keller
Sudheer Mogilappagari
Erwan Velu
Sindhu Devale
Dan Carpenter
Rahul Rameshbabu
MD Danish Anwar
Pablo Neira Ayuso
Lukas Wunner
Duanqiang Wen
Ido Schimmel
Hyunwoo Kim
Ismael Luceno
Bartosz Golaszewski
Chun-Yi Lee
Johan Hovold