| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch introduces documentation for alpine devicetree bindings.
Signed-off-by: Barak Wasserstrom <barak@annapurnalabs.com>
Signed-off-by: Tsahee Zidenberg <tsahee@annapurnalabs.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This patch introduces support for waking up secondary CPU cores on
Alpine platform.
Signed-off-by: Barak Wasserstrom <barak@annapurnalabs.com>
Signed-off-by: Tsahee Zidenberg <tsahee@annapurnalabs.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Alpine platform includes UART8250 that can be used for early prints.
Signed-off-by: Saeed Bishara <saeed@annapurnalabs.com>
Signed-off-by: Tsahee Zidenberg <tsahee@annapurnalabs.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This patch introduces initial architecture and device-tree support.
Signed-off-by: Saeed Bishara <saeed@annapurnalabs.com>
Signed-off-by: Tsahee Zidenberg <tsahee@annapurnalabs.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add a device node for the da9063 PMIC, with subnodes for rtc and wdt.
Regulator support is not yet included.
This allows the system to be restarted when the watchdog timer times
out, or when a system restart is requested.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The da9210 regulator is connected to IRQ2. Reflect this in its device
node, so the driver can use it when it gains interrupt support.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add a device node for the da9063 PMIC, with subnodes for rtc and wdt.
Regulator support is not yet included.
This allows the system to be restarted when the watchdog timer times
out, or when a system restart is requested.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The da9210 regulator is connected to IRQ2. Reflect this in its device
node, so the driver can use it when it gains interrupt support.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The r8a7790/lager and r8a7791/koelsch development boards have da9063 and
da9210 regulators. Both regulators have their interrupt request lines
tied to the same interrupt pin (IRQ2) on the SoC.
After cold boot or da9063-induced restart, both the da9063 and da9210
seem to assert their interrupt request lines. Hence as soon as one
driver requests this irq, it gets stuck in an interrupt storm, as it
only manages to deassert its own interrupt request line, and the other
driver hasn't installed an interrupt handler yet.
To handle this, install a quirk that masks the interrupts in both the
da9063 and da9210. This quirk has to run after the i2c master driver
has been initialized, but before the i2c slave drivers are initialized.
As it depends on i2c, select I2C if one of the affected platforms is
enabled in the kernel config.
On koelsch, the following happens:
- Cold boot or reboot using the da9063 restart handler:
IRQ2 is asserted, installing da9063/da9210 regulator quirk
...
i2c i2c-6: regulator_quirk_notify: 1, IRQC_MONITOR = 0x3fb
i2c 6-0058: regulator_quirk_notify: 1, IRQC_MONITOR = 0x3fb
i2c 6-0058: Detected da9063
i2c 6-0058: Masking da9063 interrupt sources
i2c 6-0068: regulator_quirk_notify: 1, IRQC_MONITOR = 0x3fb
i2c 6-0068: Detected da9210
i2c 6-0068: Masking da9210 interrupt sources
i2c 6-0068: IRQ2 is not asserted, removing quirk
- Warm boot (reset button):
rcar_gen2_regulator_quirk: IRQ2 is not asserted, not installing quirk
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Now that we support Armada 39x, let's add this family of SoC to the
Marvell documentation, and a reference to a link with more details
about those processors. Unfortunately, no datasheet is publicly
available at this time.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
This commit adds the core support for Armada 39x, which is quite
simple:
- a new Kconfig option which selects the appropriate clock and
pinctrl drivers as well as other common features (GIC, L2 cache,
SMP, etc.)
- a new DT_MACHINE_START which references the top-level compatible
strings supported for the Marvell Armada 39x.
- a new SMP enable-method. The mechanism to enable CPUs for Armada
39x appears to be the same as Armada 38x. However, we do not want
to use marvell,armada-380-smp in the Device Tree, in the case of
the discovery of a subtle difference in the future, which would
require changing the Device Tree. And the enable-method isn't a
compatible string: you can't specify several values and expect a
fallback on the second string if the first one isn't
supported. Therefore, we simply declare the SMP enable method
"marvell,armada-390-smp" as doing the same thing as the
"marvell,armada-380-smp" one.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
This commit updates the ARM CPUs Device Tree binding to document a new
enable method of Marvell Armada 39x processors.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
Tsahee Zidenberg
Geert Uytterhoeven
Thomas Petazzoni