| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Andrey used the syzkaller fuzzer to find an out-of-bounds memory
access in usb_get_bos_descriptor(). The code wasn't checking that the
next usb_dev_cap_header structure could fit into the remaining buffer
space.
This patch fixes the error and also reduces the bNumDeviceCaps field
in the header to match the actual number of capabilities found, in
cases where there are fewer than expected.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 3b2435192fe91 ("MAINTAINERS: drop OMAP USB and MUSB
maintainership") switched the maintainer for musb module, but didn't
update the git tree location.
Delete the git tree information, since the current maintainer doesn't
have a public tree.
Reported-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This keyboard doesn't implement Get String descriptors properly even
though string indexes are valid. What happens is that when requesting
for the String descriptor, the device disconnects and
reconnects. Without this quirk, this loop will continue forever.
Cc: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Владимир Мартьянов <vilgeforce@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This fixes a kernel oops when unloading the driver due to usb_put_phy
being called after usb_phy_generic_unregister when the device is
detached. Calling usb_phy_generic_unregister causes x->dev->driver to
be NULL in usb_put_phy and results in a NULL pointer dereference.
Cc: stable@vger.kernel.org # v4.3+
Signed-off-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The sunxi musb has a bug where sometimes it will generate a babble
error on device disconnect instead of a disconnect IRQ. When this
happens the musb controller switches from host mode to device mode
(it clears MUSB_DEVCTL_HM/MUSB_DEVCTL_SESSION and sets
MUSB_DEVCTL_BDEVICE) and gets stuck in this state.
The babble error is misdetected as a bus reset because MUSB_DEVCTL_HM
was cleared.
To fix this, use is_host_active() rather than (devctl & MUSB_DEVCTL_HM)
to detect babble error so that sunxi musb babble recovery can handle it
by restoring the mode. This information is provided by the driver logic
and does not rely on register contents.
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently, the number of channels is set to 15 but in the case of DA8xx,
the number of channels is 4.
Update the driver to configure the number of channels at runtime.
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The way to configure the DMA mode on DA8xx is different from DSPS.
Add a new function to configure DMA mode on DA8xx and use a callback
to call the right function based on the platform.
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The DA8xx and DSPS platforms don't use the same address for few registers.
On Da8xx, this is causing some issues (e.g. teardown that doesn't work).
Configure the address of the register during the init and use them instead
of constants.
Cc: stable@vger.kernel.org # v4.12+
Reported-by: nsekhar@ti.com
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The musb delayed irq work was never flushed on suspend, something which
since 4.9 can lead to an external abort if the work is scheduled after
the grandparent's clock has been disabled:
PM: Suspending system (mem)
PM: suspend of devices complete after 125.224 msecs
PM: suspend devices took 0.132 seconds
PM: late suspend of devices complete after 7.423 msecs
PM: noirq suspend of devices complete after 7.083 msecs
suspend debug: Waiting for 5 second(s).
Unhandled fault: external abort on non-linefetch (0x1008) at 0xd0262c60
...
[<c054880c>] (musb_default_readb) from [<c0547b5c>] (musb_irq_work+0x48/0x220)
[<c0547b5c>] (musb_irq_work) from [<c014f8a4>] (process_one_work+0x1f4/0x758)
[<c014f8a4>] (process_one_work) from [<c014fe5c>] (worker_thread+0x54/0x514)
[<c014fe5c>] (worker_thread) from [<c015704c>] (kthread+0x128/0x158)
[<c015704c>] (kthread) from [<c0109330>] (ret_from_fork+0x14/0x24)
Commit 2bff3916fda9 ("usb: musb: Fix PM for hub disconnect") started
scheduling musb_irq_work with a delay of up to a second and with
retries thereby making this easy to trigger, for example, by suspending
shortly after a disconnect.
Note that we set a flag to prevent the irq work from rescheduling itself
during suspend and instead process a disconnect immediately. This takes
care of the case where we are disconnected shortly before suspending.
However, when in host mode, a disconnect while suspended will still
go unnoticed and thus prevent the controller from runtime suspending
upon resume as the session bit is always set. This will need to be
addressed separately.
Fixes: 550a7375fe72 ("USB: Add MUSB and TUSB support")
Fixes: 467d5c980709 ("usb: musb: Implement session bit based runtime PM for musb-core")
Fixes: 2bff3916fda9 ("usb: musb: Fix PM for hub disconnect")
Cc: stable <stable@vger.kernel.org> # 4.9
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The current session-bit quirk implementation does not prevent the retry
counter from underflowing, something which could break runtime PM and
keep the device active for a very long time (about 2^32 seconds) after a
disconnect.
This notably breaks the B-device timeout case, but could potentially
cause problems also when the controller is operating as an A-device.
Fixes: 2bff3916fda9 ("usb: musb: Fix PM for hub disconnect")
Cc: stable <stable@vger.kernel.org> # 4.9
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Elatec TWN3 has the union descriptor on data interface. This results in
failure to bind the device to the driver with the following log:
usb 1-1.2: new full speed USB device using streamplug-ehci and address 4
usb 1-1.2: New USB device found, idVendor=09d8, idProduct=0320
usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1.2: Product: RFID Device (COM)
usb 1-1.2: Manufacturer: OEM
cdc_acm 1-1.2:1.0: Zero length descriptor references
cdc_acm: probe of 1-1.2:1.0 failed with error -22
Adding the NO_UNION_NORMAL quirk for the device fixes the issue.
`lsusb -v` of the device:
Bus 001 Device 003: ID 09d8:0320
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 2 Communications
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 32
idVendor 0x09d8
idProduct 0x0320
bcdDevice 3.00
iManufacturer 1 OEM
iProduct 2 RFID Device (COM)
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 67
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 250mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 1 AT-commands (v.25ter)
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0020 1x 32 bytes
bInterval 2
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 10 CDC Data
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0020 1x 32 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0020 1x 32 bytes
bInterval 0
CDC Header:
bcdCDC 1.10
CDC Call Management:
bmCapabilities 0x03
call management
use DataInterface
bDataInterface 1
CDC ACM:
bmCapabilities 0x06
sends break
line coding and serial state
CDC Union:
bMasterInterface 0
bSlaveInterface 1
Device Status: 0x0000
(Bus Powered)
Signed-off-by: Maksim Salau <msalau@iotecha.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Taking the uurb->buffer_length userspace passes in as a maximum for the
actual urbs transfer_buffer_length causes 2 serious issues:
1) It breaks isochronous support for all userspace apps using libusb,
as existing libusb versions pass in 0 for uurb->buffer_length,
relying on the kernel using the lenghts of the usbdevfs_iso_packet_desc
descriptors passed in added together as buffer length.
This for example causes redirection of USB audio and Webcam's into
virtual machines using qemu-kvm to no longer work. This is a userspace
ABI break and as such must be reverted.
Note that the original commit does not protect other users / the
kernels memory, it only stops the userspace process making the call
from shooting itself in the foot.
2) It may cause the kernel to program host controllers to DMA over random
memory. Just as the devio code used to only look at the iso_packet_desc
lenghts, the host drivers do the same, relying on the submitter of the
urbs to make sure the entire buffer is large enough and not checking
transfer_buffer_length.
But the "USB: devio: Don't corrupt user memory" commit now takes the
userspace provided uurb->buffer_length for the buffer-size while copying
over the user-provided iso_packet_desc lengths 1:1, allowing the user
to specify a small buffer size while programming the host controller to
dma a lot more data.
(Atleast the ohci, uhci, xhci and fhci drivers do not check
transfer_buffer_length for isoc transfers.)
This reverts commit fa1ed74eb1c2 ("USB: devio: Don't corrupt user memory")
fixing both these issues.
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xhci_stop_device() calls xhci_queue_stop_endpoint() multiple times
without checking the return value. xhci_queue_stop_endpoint() can
return error if the HC is already halted or unable to queue commands.
This can cause a deadlock condition as xhci_stop_device() would
end up waiting indefinitely for a completion for the command that
didn't get queued. Fix this by checking the return value and bailing
out of xhci_stop_device() in case of error. This patch happens to fix
potential memory leaks of the allocated command structures as well.
Fixes: c311e391a7ef ("xhci: rework command timeout and cancellation,")
Cc: <stable@vger.kernel.org>
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When a URB is cancled, xhci driver turns the untransferred trbs
into no-ops. If an endpoint stalls on a no-op trb that belongs
to the cancelled URB, the event handler won't reset the endpoint.
Hence, it will stay halted.
Link: http://marc.info/?l=linux-usb&m=149582598330127&w=2
Cc: <stable@vger.kernel.org>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
KASAN reported use-after-free bug when xhci host controller died:
[ 176.952537] BUG: KASAN: use-after-free in xhci_handle_command_timeout+0x68/0x224
[ 176.960846] Write of size 4 at addr ffffffc0cbb01608 by task kworker/3:3/1680
...
[ 177.180644] Freed by task 0:
[ 177.183882] kasan_slab_free+0x90/0x15c
[ 177.188194] kfree+0x114/0x28c
[ 177.191630] xhci_cleanup_command_queue+0xc8/0xf8
[ 177.196916] xhci_hc_died+0x84/0x358
Problem here is that when the cmd_timer fired, it would try to access
current_cmd while the command queue is already freed by xhci_hc_died().
Cleanup current_cmd in xhci_cleanup_command_queue() to avoid that.
Fixes: d9f11ba9f107 ("xhci: Rework how we handle unresponsive or hoptlug removed hosts")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Many USB 3.1 capable hosts never updated the Serial Bus Release Number
(SBRN) register to USB 3.1 from USB 3.0
xhci driver identified USB 3.1 capable hosts based on this SBRN register,
which according to specs "contains the release of the Universal Serial
Bus Specification with which this Universal Serial Bus Host Controller
module is compliant." but still in october 2017 gives USB 3.0 as
the only possible option.
Make an additional check for USB 3.1 support and enable it if the xHCI
supported protocol capablity lists USB 3.1 capable ports.
Cc: <stable@vger.kernel.org> # v4.6+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add device-id entry for (Honeywell) Metrologic MS7820 bar code scanner.
The device has two interfaces (in this mode?); a vendor-specific
interface with two interrupt endpoints and a second HID interface, which
we do not bind to.
Reported-by: Ladislav Dobrovsky <ladislav.dobrovsky@gmail.com>
Tested-by: Ladislav Dobrovsky <ladislav.dobrovsky@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
|
|
On CPUs like AMD's Geode, for example, we shouldn't even try to load
microcode because they do not support the modern microcode loading
interface.
However, we do the family check *after* the other checks whether the
loader has been disabled on the command line or whether we're running in
a guest.
So move the family checks first in order to exit early if we're being
loaded on an unsupported family.
Reported-and-tested-by: Sven Glodowski <glodi1@arcor.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org> # 4.11..
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://bugzilla.suse.com/show_bug.cgi?id=1061396
Link: http://lkml.kernel.org/r/20171012112316.977-1-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Johan Hovold reported a big lockdep slowdown on his system, caused by lockdep:
> I had noticed that the BeagleBone Black boot time appeared to have
> increased significantly with 4.14 and yesterday I finally had time to
> investigate it.
>
> Boot time (from "Linux version" to login prompt) had in fact doubled
> since 4.13 where it took 17 seconds (with my current config) compared to
> the 35 seconds I now see with 4.14-rc4.
>
> I quick bisect pointed to lockdep and specifically the following commit:
>
> 28a903f63ec0 ("locking/lockdep: Handle non(or multi)-acquisition of a crosslock")
Because the final v4.14 release is close, disable the cross-release lockdep
features for now.
Bisected-by: Johan Hovold <johan@kernel.org>
Debugged-by: Johan Hovold <johan@kernel.org>
Reported-by: Johan Hovold <johan@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Byungchul Park <byungchul.park@lge.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Lindgren <tony@atomide.com>
Cc: kernel-team@lge.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mm@kvack.org
Cc: linux-omap@vger.kernel.org
Link: http://lkml.kernel.org/r/20171014072659.f2yr6mhm5ha3eou7@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Since commit:
94b1b03b519b ("x86/mm: Rework lazy TLB mode and TLB freshness tracking")
x86's lazy TLB mode has been all the way lazy: when running a kernel thread
(including the idle thread), the kernel keeps using the last user mm's
page tables without attempting to maintain user TLB coherence at all.
From a pure semantic perspective, this is fine -- kernel threads won't
attempt to access user pages, so having stale TLB entries doesn't matter.
Unfortunately, I forgot about a subtlety. By skipping TLB flushes,
we also allow any paging-structure caches that may exist on the CPU
to become incoherent. This means that we can have a
paging-structure cache entry that references a freed page table, and
the CPU is within its rights to do a speculative page walk starting
at the freed page table.
I can imagine this causing two different problems:
- A speculative page walk starting from a bogus page table could read
IO addresses. I haven't seen any reports of this causing problems.
- A speculative page walk that involves a bogus page table can install
garbage in the TLB. Such garbage would always be at a user VA, but
some AMD CPUs have logic that triggers a machine check when it notices
these bogus entries. I've seen a couple reports of this.
Boris further explains the failure mode:
> It is actually more of an optimization which assumes that paging-structure
> entries are in WB DRAM:
>
> "TlbCacheDis: cacheable memory disable. Read-write. 0=Enables
> performance optimization that assumes PML4, PDP, PDE, and PTE entries
> are in cacheable WB-DRAM; memory type checks may be bypassed, and
> addresses outside of WB-DRAM may result in undefined behavior or NB
> protocol errors. 1=Disables performance optimization and allows PML4,
> PDP, PDE and PTE entries to be in any memory type. Operating systems
> that maintain page tables in memory types other than WB- DRAM must set
> TlbCacheDis to insure proper operation."
>
> The MCE generated is an NB protocol error to signal that
>
> "Link: A specific coherent-only packet from a CPU was issued to an
> IO link. This may be caused by software which addresses page table
> structures in a memory type other than cacheable WB-DRAM without
> properly configuring MSRC001_0015[TlbCacheDis]. This may occur, for
> example, when page table structure addresses are above top of memory. In
> such cases, the NB will generate an MCE if it sees a mismatch between
> the memory operation generated by the core and the link type."
>
> I'm assuming coherent-only packets don't go out on IO links, thus the
> error.
To fix this, reinstate TLB coherence in lazy mode. With this patch
applied, we do it in one of two ways:
- If we have PCID, we simply switch back to init_mm's page tables
when we enter a kernel thread -- this seems to be quite cheap
except for the cost of serializing the CPU.
- If we don't have PCID, then we set a flag and switch to init_mm
the first time we would otherwise need to flush the TLB.
The /sys/kernel/debug/x86/tlb_use_lazy_mode debug switch can be changed
to override the default mode for benchmarking.
In theory, we could optimize this better by only flushing the TLB in
lazy CPUs when a page table is freed. Doing that would require
auditing the mm code to make sure that all page table freeing goes
through tlb_remove_page() as well as reworking some data structures
to implement the improved flush logic.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Reported-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Eric Biggers <ebiggers@google.com>
Cc: Johannes Hirte <johannes.hirte@datenkhaos.de>
Cc: Kees Cook <keescook@chromium.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nadav Amit <nadav.amit@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Roman Kagan <rkagan@virtuozzo.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 94b1b03b519b ("x86/mm: Rework lazy TLB mode and TLB freshness tracking")
Link: http://lkml.kernel.org/r/20171009170231.fkpraqokz6e4zeco@pd.tnic
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
When the VMA based swap readahead was introduced, a new knob
/sys/kernel/mm/swap/vma_ra_max_order
was added as the max window of VMA swap readahead. This is to make it
possible to use different max window for VMA based readahead and
original physical readahead. But Minchan Kim pointed out that this will
cause a regression because setting page-cluster sysctl to zero cannot
disable swap readahead with the change.
To fix the regression, the page-cluster sysctl is used as the max window
of both the VMA based swap readahead and original physical swap
readahead. If more fine grained control is needed in the future, more
knobs can be added as the subordinate knobs of the page-cluster sysctl.
The vma_ra_max_order knob is deleted. Because the knob was introduced
in v4.14-rc1, and this patch is targeting being merged before v4.14
releasing, there should be no existing users of this newly added ABI.
Link: http://lkml.kernel.org/r/20171011070847.16003-1-ying.huang@intel.com
Fixes: ec560175c0b6fce ("mm, swap: VMA based swap readahead")
Signed-off-by: "Huang, Ying" <ying.huang@intel.com>
Reported-by: Minchan Kim <minchan@kernel.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Shaohua Li <shli@kernel.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Tim Chen <tim.c.chen@intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Loading the pmd without holding the pmd_lock exposes us to races with
concurrent updaters of the page tables but, worse still, it also allows
the compiler to cache the pmd value in a register and reuse it later on,
even if we've performed a READ_ONCE in between and seen a more recent
value.
In the case of page_vma_mapped_walk, this leads to the following crash
when the pmd loaded for the initial pmd_trans_huge check is all zeroes
and a subsequent valid table entry is loaded by check_pmd. We then
proceed into map_pte, but the compiler re-uses the zero entry inside
pte_offset_map, resulting in a junk pointer being installed in
pvmw->pte:
PC is at check_pte+0x20/0x170
LR is at page_vma_mapped_walk+0x2e0/0x540
[...]
Process doio (pid: 2463, stack limit = 0xffff00000f2e8000)
Call trace:
check_pte+0x20/0x170
page_vma_mapped_walk+0x2e0/0x540
page_mkclean_one+0xac/0x278
rmap_walk_file+0xf0/0x238
rmap_walk+0x64/0xa0
page_mkclean+0x90/0xa8
clear_page_dirty_for_io+0x84/0x2a8
mpage_submit_page+0x34/0x98
mpage_process_page_bufs+0x164/0x170
mpage_prepare_extent_to_map+0x134/0x2b8
ext4_writepages+0x484/0xe30
do_writepages+0x44/0xe8
__filemap_fdatawrite_range+0xbc/0x110
file_write_and_wait_range+0x48/0xd8
ext4_sync_file+0x80/0x4b8
vfs_fsync_range+0x64/0xc0
SyS_msync+0x194/0x1e8
This patch fixes the problem by ensuring that READ_ONCE is used before
the initial checks on the pmd, and this value is subsequently used when
checking whether or not the pmd is present. pmd_check is removed and
the pmd_present check is inlined directly.
Link: http://lkml.kernel.org/r/1507222630-5839-1-git-send-email-will.deacon@arm.com
Fixes: f27176cfc363 ("mm: convert page_mkclean_one() to use page_vma_mapped_walk()")
Signed-off-by: Will Deacon <will.deacon@arm.com>
Tested-by: Yury Norov <ynorov@caviumnetworks.com>
Tested-by: Richard Ruigrok <rruigrok@codeaurora.org>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Kmemleak considers any pointers on task stacks as references. This
patch clears newly allocated and reused vmap stacks.
Link: http://lkml.kernel.org/r/150728990124.744199.8403409836394318684.stgit@buzz
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
inode->i_private is assigned by a Node pointer only after registering a
new binary format, so it could be NULL if inode was created by
bm_fill_super() (or iput() was called by the error path in
bm_register_write()), and this could result in NULL pointer dereference
when evicting such an inode. e.g. mount binfmt_misc filesystem then
umount it immediately:
mount -t binfmt_misc binfmt_misc /proc/sys/fs/binfmt_misc
umount /proc/sys/fs/binfmt_misc
will result in
BUG: unable to handle kernel NULL pointer dereference at 0000000000000013
IP: bm_evict_inode+0x16/0x40 [binfmt_misc]
...
Call Trace:
evict+0xd3/0x1a0
iput+0x17d/0x1d0
dentry_unlink_inode+0xb9/0xf0
__dentry_kill+0xc7/0x170
shrink_dentry_list+0x122/0x280
shrink_dcache_parent+0x39/0x90
do_one_tree+0x12/0x40
shrink_dcache_for_umount+0x2d/0x90
generic_shutdown_super+0x1f/0x120
kill_litter_super+0x29/0x40
deactivate_locked_super+0x43/0x70
deactivate_super+0x45/0x60
cleanup_mnt+0x3f/0x70
__cleanup_mnt+0x12/0x20
task_work_run+0x86/0xa0
exit_to_usermode_loop+0x6d/0x99
syscall_return_slowpath+0xba/0xf0
entry_SYSCALL_64_fastpath+0xa3/0xa
Fix it by making sure Node (e) is not NULL.
Link: http://lkml.kernel.org/r/20171010100642.31786-1-eguan@redhat.com
Fixes: 83f918274e4b ("exec: binfmt_misc: shift filp_close(interp_file) from kill_node() to bm_evict_inode()")
Signed-off-by: Eryu Guan <eguan@redhat.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When using FAT on a block device which supports rw_page, we can hit
BUG_ON(!PageLocked(page)) in try_to_free_buffers(). This is because we
call clean_buffers() after unlocking the page we've written. Introduce
a new clean_page_buffers() which cleans all buffers associated with a
page and call it from within bdev_write_page().
[akpm@linux-foundation.org: s/PAGE_SIZE/~0U/ per Linus and Matthew]
Link: http://lkml.kernel.org/r/20171006211541.GA7409@bombadil.infradead.org
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Reported-by: Toshi Kani <toshi.kani@hpe.com>
Reported-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Tested-by: Toshi Kani <toshi.kani@hpe.com>
Acked-by: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add kernel-doc notation for some macros. Correct kernel-doc comments &
typos for a few macros.
Link: http://lkml.kernel.org/r/76fa1403-1511-be4c-e9c4-456b43edfad3@infradead.org
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We have seen NULL-pointer dereference crashes in tty->disc_data when the
N_TTY fallback driver failed to open during hangup. The immediate cause
of this open to fail has been addressed in the preceding patch to
vmalloc(), but this code could be more robust.
As Alan pointed out in commit 8a8dabf2dd68 ("tty: handle the case where
we cannot restore a line discipline"), the N_TTY driver, historically
the safe fallback that could never fail, can indeed fail, but the
surrounding code is not prepared to handle this. To avoid crashes he
added a new N_NULL driver to take N_TTY's place as the last resort.
Hook that fallback up to the hangup path. Update tty_ldisc_reinit() to
reflect the reality that n_tty_open can indeed fail.
Link: http://lkml.kernel.org/r/20171004185959.GC2136@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Alan Cox <alan@llwyncelyn.cymru>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This reverts commits 5d17a73a2ebe ("vmalloc: back off when the current
task is killed") and 171012f56127 ("mm: don't warn when vmalloc() fails
due to a fatal signal").
Commit 5d17a73a2ebe ("vmalloc: back off when the current task is
killed") made all vmalloc allocations from a signal-killed task fail.
We have seen crashes in the tty driver from this, where a killed task
exiting tries to switch back to N_TTY, fails n_tty_open because of the
vmalloc failing, and later crashes when dereferencing tty->disc_data.
Arguably, relying on a vmalloc() call to succeed in order to properly
exit a task is not the most robust way of doing things. There will be a
follow-up patch to the tty code to fall back to the N_NULL ldisc.
But the justification to make that vmalloc() call fail like this isn't
convincing, either. The patch mentions an OOM victim exhausting the
memory reserves and thus deadlocking the machine. But the OOM killer is
only one, improbable source of fatal signals. It doesn't make sense to
fail allocations preemptively with plenty of memory in most cases.
The patch doesn't mention real-life instances where vmalloc sites would
exhaust memory, which makes it sound more like a theoretical issue to
begin with. But just in case, the OOM access to memory reserves has
been restricted on the allocator side in cd04ae1e2dc8 ("mm, oom: do not
rely on TIF_MEMDIE for memory reserves access"), which should take care
of any theoretical concerns on that front.
Revert this patch, and the follow-up that suppresses the allocation
warnings when we fail the allocations due to a signal.
Link: http://lkml.kernel.org/r/20171004185906.GB2136@cmpxchg.org
Fixes: 171012f56127 ("mm: don't warn when vmalloc() fails due to a fatal signal")
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Alan Cox <alan@llwyncelyn.cymru>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
cma_alloc() unconditionally prints an INFO message when the CMA
allocation fails. Make this message conditional on the non-presence of
__GFP_NOWARN in gfp_mask.
This patch aims at removing INFO messages that are displayed when the
VC4 driver tries to allocate buffer objects. From the driver
perspective an allocation failure is acceptable, and the driver can
possibly do something to make following allocation succeed (like
flushing the VC4 internal cache).
Link: http://lkml.kernel.org/r/20171004125447.15195-1-boris.brezillon@free-electrons.com
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Laura Abbott <labbott@redhat.com>
Cc: Jaewon Kim <jaewon31.kim@samsung.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Eric Anholt <eric@anholt.net>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
gcc on aarch64 may emit synbols of type 'n' if the kernel is built with
'-frecord-gcc-switches'. In most cases, those symbols are reported with
nm as
000000000000000e n $d
and with objdump as
0000000000000000 l d .GCC.command.line 0000000000000000 .GCC.command.line
000000000000000e l .GCC.command.line 0000000000000000 $d
Those symbols are detected in is_arm_mapping_symbol() and ignored.
However, if "--prefix-symbols=<prefix>" is configured as well, the
situation is different. For example, in efi/libstub, arm64 images are
built with
'--prefix-alloc-sections=.init --prefix-symbols=__efistub_'.
In combination with '-frecord-gcc-switches', the symbols are now reported
by nm as:
000000000000000e n __efistub_$d
and by objdump as:
0000000000000000 l d .GCC.command.line 0000000000000000 .GCC.command.line
000000000000000e l .GCC.command.line 0000000000000000 __efistub_$d
Those symbols are no longer ignored and included in the base address
calculation. This results in a base address of 000000000000000e, which
in turn causes kallsyms to abort with
kallsyms failure:
relative symbol value 0xffffff900800a000 out of range in relative mode
The problem is seen in little endian arm64 builds with CONFIG_EFI
enabled and with '-frecord-gcc-switches' set in KCFLAGS.
Explicitly ignore symbols of type 'n' since those are clearly debug
symbols.
Link: http://lkml.kernel.org/r/1507136063-3139-1-git-send-email-linux@roeck-us.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I was stress testing some backports and with high load, after some time,
the latest version of the selftest showed some false positive in
connection with the uffdio_copy_retry. This seems to fix it while still
exercising -EEXIST in the background transfer once in a while.
The fork child will quit after the last UFFDIO_COPY is run, so a
repeated UFFDIO_COPY may not return -EEXIST. This change restricts the
-EEXIST stress to the background transfer where the memory can't go away
from under it.
Also updated uffdio_zeropage, so the interface is consistent.
Link: http://lkml.kernel.org/r/20171004171541.1495-2-aarcange@redhat.com
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Pavel Emelyanov <xemul@virtuozzo.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When I execute numactl -H (which reads /sys/devices/system/node/nodeX/cpumap
and displays cpumask_of_node for each node), I get different result
on X86 and arm64. For each numa node, the former only displayed online
CPUs, and the latter displayed all possible CPUs. Unfortunately, both
Linux documentation and numactl manual have not described it clear.
I sent a mail to ask for help, and Michal Hocko replied that he
preferred to print online cpus because it doesn't really make much sense
to bind anything on offline nodes.
Will said:
"I suspect the vast majority (if not all) code that reads this file was
developed for x86, so having the same behaviour for arm64 sounds like
something we should do ASAP before people try to special case with
things like #ifdef __aarch64__. I'd rather have this in 4.14 if
possible."
Link: http://lkml.kernel.org/r/1506678805-15392-2-git-send-email-thunder.leizhen@huawei.com
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Tianhong Ding <dingtianhong@huawei.com>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Libin <huawei.libin@huawei.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
A non present pmd entry can appear after pmd_lock is taken in
page_vma_mapped_walk(), even if THP migration is not enabled. The
WARN_ONCE is unnecessary.
Link: http://lkml.kernel.org/r/20171003142606.12324-1-zi.yan@sent.com
Fixes: 616b8371539a ("mm: thp: enable thp migration in generic path")
Signed-off-by: Zi Yan <zi.yan@cs.rutgers.edu>
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Tested-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 3a321d2a3dde ("mm: change the call sites of numa statistics
items") separated NUMA counters from zone counters, but the
NUMA_INTERLEAVE_HIT call site wasn't updated to use the new interface.
So alloc_page_interleave() actually increments NR_ZONE_INACTIVE_FILE
instead of NUMA_INTERLEAVE_HIT.
Fix this by using __inc_numa_state() interface to increment
NUMA_INTERLEAVE_HIT.
Link: http://lkml.kernel.org/r/20171003191003.8573-1-aryabinin@virtuozzo.com
Fixes: 3a321d2a3dde ("mm: change the call sites of numa statistics items")
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Cc: Kemi Wang <kemi.wang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The pci-rcar driver is enabled for compile tests, and this has shown that
the driver cannot build without CONFIG_OF, following the inclusion of
commit f8f2fe7355fb ("PCI: rcar: Use new OF interrupt mapping when possible"):
drivers/pci/host/pcie-rcar.c: In function 'pci_dma_range_parser_init':
drivers/pci/host/pcie-rcar.c:1039:2: error: implicit declaration of function 'of_n_addr_cells' [-Werror=implicit-function-declaration]
parser->pna = of_n_addr_cells(node);
^
As pointed out by Ben Dooks and Geert Uytterhoeven, this is actually
supposed to build fine, which we can achieve if we make the declaration
of of_irq_parse_and_map_pci conditional on CONFIG_OF and provide an
empty inline function otherwise, as we do for a lot of other of
interfaces.
This lets us build the rcar_pci driver again without CONFIG_OF for build
testing. All platforms using this driver select OF, so this doesn't
change anything for the users.
[akpm@linux-foundation.org: be consistent with surrounding code]
Link: http://lkml.kernel.org/r/20170911200805.3363318-1-arnd@arndb.de
Fixes: c25da4778803 ("PCI: rcar: Add Renesas R-Car PCIe driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Frank Rowand <frank.rowand@sony.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Magnus Damm <damm@opensource.se>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
mm/madvise.c has a brief description about all MADV_ flags. Add a
description for the newly added MADV_WIPEONFORK and MADV_KEEPONFORK.
Although man page has the similar information, but it'd better to keep
the consistent with other flags.
Link: http://lkml.kernel.org/r/1506117328-88228-1-git-send-email-yang.s@alibaba-inc.com
Signed-off-by: Yang Shi <yang.s@alibaba-inc.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Expand the "Runtime testing" menu by including more entries inside it
instead of after it. This is just Kconfig symbol movement.
This causes the (arch-independent) Runtime tests to be presented
(listed) all in one place instead of in multiple places.
Link: http://lkml.kernel.org/r/c194e5c4-2042-bf94-a2d8-7aa13756e257@infradead.org
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: "Luis R. Rodriguez" <mcgrof@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Index was incremented before last use and thus the second array could
dereference to an invalid address (not mentioning the fact that it did
not properly clear the entry we intended to clear).
Link: http://lkml.kernel.org/r/1506973525-16491-1-git-send-email-jglisse@redhat.com
Fixes: 8315ada7f095bf ("mm/migrate: allow migrate_vma() to alloc new page on empty entry")
Signed-off-by: Mark Hairgrove <mhairgrove@nvidia.com>
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Cc: Reza Arbab <arbab@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The function only sends the flush command to the IOMMU(s),
but does not wait for its completion when it returns. Fix
that.
Fixes: 601367d76bd1 ('x86/amd-iommu: Remove iommu_flush_domain function')
Cc: stable@vger.kernel.org # >= 2.6.33
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Panic observed with latest firmware, and upstream kernel:
NIP init_imc_pmu+0x8c/0xcf0
LR init_imc_pmu+0x2f8/0xcf0
Call Trace:
init_imc_pmu+0x2c8/0xcf0 (unreliable)
opal_imc_counters_probe+0x300/0x400
platform_drv_probe+0x64/0x110
driver_probe_device+0x3d8/0x580
__driver_attach+0x14c/0x1a0
bus_for_each_dev+0x8c/0xf0
driver_attach+0x34/0x50
bus_add_driver+0x298/0x350
driver_register+0x9c/0x180
__platform_driver_register+0x5c/0x70
opal_imc_driver_init+0x2c/0x40
do_one_initcall+0x64/0x1d0
kernel_init_freeable+0x280/0x374
kernel_init+0x24/0x160
ret_from_kernel_thread+0x5c/0x74
While registering nest imc at init, cpu-hotplug callback
nest_pmu_cpumask_init() makes an OPAL call to stop the engine. And if
the OPAL call fails, imc_common_cpuhp_mem_free() is invoked to cleanup
memory and cpuhotplug setup.
But when cleaning up the attribute group, we are dereferencing the
attribute element array without checking whether the backing element
is not NULL. This causes the kernel panic.
Add a check for the backing element prior to dereferencing the
attribute element, to handle the failing case gracefully.
Signed-off-by: Anju T Sudhakar <anju@linux.vnet.ibm.com>
Reported-by: Pridhiviraj Paidipeddi <ppaidipe@linux.vnet.ibm.com>
[mpe: Trim change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
If faddr2line is given a function name which is the last one listed by
"nm -n", it will fail because it never finds the next symbol.
So teach the awk script to catch that possibility, and use 'size' to
provide the end point of the last function.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We need to call reservation_object_reserve_shared() in both cases, but
this wasn't happening in the _NO_IMPLICIT submit case.
Fixes: f0a42bb ("drm/msm: submit support for in-fences")
Reported-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
If we fail to attach iommu, gpu->aspace could be IS_ERR()..
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Using CONFIG_OF_DYNAMIC=y uncovered an imbalance in the usecount of the
node being passed to of_fwnode_graph_get_port_parent(). Preserve the
usecount by using of_get_parent() instead of of_get_next_parent() which
don't decrement the usecount of the node passed to it.
Fixes: 3b27d00e7b6d7c88 ("device property: Move fwnode graph ops to firmware specific locations")
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
There are two types of memory reservations firmware can ask the kernel
to make in the device tree: static and dynamic.
See Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt
If you have greater than 16 entries in /reserved-memory (as we do on
POWER9 systems) you would get this scary looking error message:
[ 0.000000] OF: reserved mem: not enough space all defined regions.
This is harmless if all your reservations are static (which with OPAL on
POWER9, they are).
It is not harmless if you have any dynamic reservations after the 16th.
In the first pass over the fdt to find reservations, the child nodes of
/reserved-memory are added to a static array in of_reserved_mem.c so that
memory can be reserved in a 2nd pass. The array has 16 entries. This is why,
on my dual socket POWER9 system, I get that error 4 times with 20 static
reservations.
We don't have a problem on ppc though, as in arch/powerpc/kernel/prom.c
we look at the new style /reserved-ranges property to do reservations,
and this logic was introduced in 0962e8004e974 (well before any powernv
system shipped).
A Google search shows up no occurances of that exact error message, so we're
probably safe in that no machine that people use has memory not being reserved
when it should be.
The simple fix is to bump the length of the array to 32 which "should be
enough for everyone(TM)". The simple fix of not recording static allocations
in the array would cause problems for devices with "memory-region" properties.
A more future-proof fix is likely possible, although more invasive and this
simple fix is perfectly suitable in the meantime while a more future-proof
fix is developed.
Signed-off-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Tested-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Do not strdup() console options. It seems that the only reason for
it to be strdup()-ed was a compilation warning: printk, UART and
console drivers, for some reason, expect char pointer instead of
const char pointer. So we can just pass `of_stdout_options', but
need to cast it to char pointer. A better fix would be to change
printk, console drivers and UART to accept const char `options';
but that will take time - there are lots of drivers to update.
The patch also fixes a possible memory leak: add_preferred_console()
can fail, but we don't kfree() options.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
While converting mdp5_enable/disable() calls to pm_runtime_get/put() API,
an extra call to pm_runtime_put_autosuspend() crept in
mdp5_crtc_cursor_set(). This results in calling the suspend handler
twice, and therefore clk_disables twice, which isn't a nice thing to do.
Fixes: d68fe15b1878 (drm/msm/mdp5: Use runtime PM get/put API instead ...)
Reported-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
The DSI runtime PM suspend/resume callbacks check whether
msm_host->cfg_hnd is non-NULL before trying to enable the bus clocks.
This is done to accommodate early calls to these functions that may
happen before the bus clocks are even initialized.
Calling pm_runtime_put_autosuspend() in dsi_host_init() can result in
racy behaviour since msm_host->cfg_hnd is set very soon after. If the
suspend callback happens too late, we end up trying to disable clocks
that were never enabled, resulting in a bunch of WARN_ON splats.
Use pm_runtime_put_sync() so that the suspend callback is called
immediately.
Reported-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
SKX stepping-3 fixed the TSC_DEADLINE issue in a different ucode
version number than stepping-4. Linux needs to know this stepping-3
specific version number to also enable the TSC_DEADLINE on stepping-3.
The steppings and ucode versions are documented in the SKX BIOS update:
https://downloadmirror.intel.com/26978/eng/ReleaseNotes_R00.01.0004.txt
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: peterz@infradead.org
Link: https://lkml.kernel.org/r/60f2bbf7cf617e212b522e663f84225bfebc50e5.1507756305.git.len.brown@intel.com
|
Alan Stern
Bin Liu
Felipe Balbi
Jonathan Liu
Alexandre Bailon
Johan Hovold
Maksim Salau
Hans de Goede
Mayank Rana
Lu Baolu
Jeffy Chen
Mathias Nyman
Linus Torvalds
Borislav Petkov
Ingo Molnar
Andy Lutomirski
Huang Ying
Will Deacon
Konstantin Khlebnikov
Eryu Guan
Matthew Wilcox
Randy Dunlap
Johannes Weiner
Boris Brezillon
Guenter Roeck
Andrea Arcangeli
Zhen Lei
Zi Yan
Andrey Ryabinin
Arnd Bergmann
Yang Shi
Mark Hairgrove
Joerg Roedel
Anju T Sudhakar
NeilBrown
Rob Clark
Niklas Söderlund
Stewart Smith
Sergey Senozhatsky
Archit Taneja
Len Brown