| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
vfs::num_msix_per should be only used as default value for
vf->num_msix. For other use cases vf->num_msix should be used, as VF can
have different MSI-X amount values.
Fix incorrect register index calculation. vfs::num_msix_per and
pf->sriov_base_vector shouldn't be used after implementation of changing
MSI-X amount on VFs. Instead vf->first_vector_idx should be used, as it
is storing value for first irq index.
Fixes: fe1c5ca2fe76 ("ice: implement num_msix field per VF")
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The rvu_dl will be freed in rvu_npa_health_reporters_destroy(rvu_dl)
after the create_workqueue fails, and after that free, the rvu_dl will
be translate back through rvu_npa_health_reporters_create,
rvu_health_reporters_create, and rvu_register_dl. Finally it goes to the
err_dl_health label, being freed again in
rvu_health_reporters_destroy(rvu) by rvu_npa_health_reporters_destroy.
In the second calls of rvu_npa_health_reporters_destroy, however,
it uses rvu_dl->rvu_npa_health_reporter, which is already freed at
the end of rvu_npa_health_reporters_destroy in the first call.
So this patch prevents the first destroy by instantly returning -ENONMEN
when create_workqueue fails. In addition, since the failure of
create_workqueue is the only entrence of label err, it has been
integrated into the error-handling path of create_workqueue.
Fixes: f1168d1e207c ("octeontx2-af: Add devlink health reporters for NPA")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Geethasowjanya Akula <gakula@marvell.com>
Link: https://lore.kernel.org/r/20231202095902.3264863-1-alexious@zju.edu.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The status bits of register MAC_FPE_CTRL_STS are clear on read. Using
32-bit read for MAC_FPE_CTRL_STS in dwmac5_fpe_configure() and
dwmac5_fpe_send_mpacket() clear the status bits. Then the stmmac interrupt
handler missing FPE event status and leads to FPE handshaking failure and
retries.
To avoid clear status bits of MAC_FPE_CTRL_STS in dwmac5_fpe_configure()
and dwmac5_fpe_send_mpacket(), add fpe_csr to stmmac_fpe_cfg structure to
cache the control bits of MAC_FPE_CTRL_STS and to avoid reading
MAC_FPE_CTRL_STS in those methods.
Fixes: 5a5586112b92 ("net: stmmac: support FPE link partner hand-shaking procedure")
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jianheng Zhang <Jianheng.Zhang@synopsys.com>
Link: https://lore.kernel.org/r/CY5PR12MB637225A7CF529D5BE0FBE59CBF81A@CY5PR12MB6372.namprd12.prod.outlook.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The current adaptive interrupt coalescing code updates only rx
packet stats for dim algorithm. This patch also updates tx packet
stats which will be useful when there is only tx traffic.
Also moved configuring hardware adaptive interrupt setting to
driver dim callback.
Fixes: 6e144b47f560 ("octeontx2-pf: Add support for adaptive interrupt coalescing")
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://lore.kernel.org/r/20231201053330.3903694-1-sumang@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Probe of Sohard Arcnet cards fails,
if 2 or more cards are installed in a system.
See kernel log:
[ 2.759203] arcnet: arcnet loaded
[ 2.763648] arcnet:com20020: COM20020 chipset support (by David Woodhouse et al.)
[ 2.770585] arcnet:com20020_pci: COM20020 PCI support
[ 2.772295] com20020 0000:02:00.0: enabling device (0000 -> 0003)
[ 2.772354] (unnamed net_device) (uninitialized): PLX-PCI Controls
...
[ 3.071301] com20020 0000:02:00.0 arc0-0 (uninitialized): PCI COM20020: station FFh found at F080h, IRQ 101.
[ 3.071305] com20020 0000:02:00.0 arc0-0 (uninitialized): Using CKP 64 - data rate 2.5 Mb/s
[ 3.071534] com20020 0000:07:00.0: enabling device (0000 -> 0003)
[ 3.071581] (unnamed net_device) (uninitialized): PLX-PCI Controls
...
[ 3.369501] com20020 0000:07:00.0: Led pci:green:tx:0-0 renamed to pci:green:tx:0-0_1 due to name collision
[ 3.369535] com20020 0000:07:00.0: Led pci:red:recon:0-0 renamed to pci:red:recon:0-0_1 due to name collision
[ 3.370586] com20020 0000:07:00.0 arc0-0 (uninitialized): PCI COM20020: station E1h found at C000h, IRQ 35.
[ 3.370589] com20020 0000:07:00.0 arc0-0 (uninitialized): Using CKP 64 - data rate 2.5 Mb/s
[ 3.370608] com20020: probe of 0000:07:00.0 failed with error -5
commit 5ef216c1f848 ("arcnet: com20020-pci: add rotary index support")
changes the device name of all COM20020 based PCI cards,
even if only some cards support this:
snprintf(dev->name, sizeof(dev->name), "arc%d-%d", dev->dev_id, i);
The error happens because all Sohard Arcnet cards would be called arc0-0,
since the Sohard Arcnet cards don't have a PLX rotary coder.
I.e. EAE Arcnet cards have a PLX rotary coder,
which sets the first decimal, ensuring unique devices names.
This patch adds two new card feature flags to indicate
which cards support LEDs and the PLX rotary coder.
For EAE based cards the names still depend on the PLX rotary coder
(untested, since missing EAE hardware).
For Sohard based cards, this patch will result in devices
being called arc0, arc1, ... (tested).
Signed-off-by: Thomas Reichinger <thomas.reichinger@sohard.de>
Fixes: 5ef216c1f848 ("arcnet: com20020-pci: add rotary index support")
Link: https://lore.kernel.org/r/20231130113503.6812-1-thomas.reichinger@sohard.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In some potential instances the reference count on struct packet_sock
could be saturated and cause overflows which gets the kernel a bit
confused. To prevent this, move to a 64-bit atomic reference count on
64-bit architectures to prevent the possibility of this type to overflow.
Because we can not handle saturation, using refcount_t is not possible
in this place. Maybe someday in the future if it changes it could be
used. Also, instead of using plain atomic64_t, use atomic_long_t instead.
32-bit machines tend to be memory-limited (i.e. anything that increases
a reference uses so much memory that you can't actually get to 2**32
references). 32-bit architectures also tend to have serious problems
with 64-bit atomics. Hence, atomic_long_t is the more natural solution.
Reported-by: "The UK's National Cyber Security Centre (NCSC)" <security@ncsc.gov.uk>
Co-developed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable@kernel.org
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20231201131021.19999-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Delay loops in r8152 should break out if RTL8152_INACCESSIBLE is set
so that they don't delay too long if the device becomes
inaccessible. Add the break to the loop in r8153_aldps_en().
Fixes: 4214cc550bf9 ("r8152: check if disabling ALDPS is finished")
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Delay loops in r8152 should break out if RTL8152_INACCESSIBLE is set
so that they don't delay too long if the device becomes
inaccessible. Add the break to the loop in r8153_pre_firmware_1().
Fixes: 9370f2d05a2a ("r8152: support request_firmware for RTL8153")
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Delay loops in r8152 should break out if RTL8152_INACCESSIBLE is set
so that they don't delay too long if the device becomes
inaccessible. Add the break to the loop in
r8156b_wait_loading_flash().
Fixes: 195aae321c82 ("r8152: support new chips")
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previous commits added checks for RTL8152_INACCESSIBLE in the loops in
the driver. There are still a few more that keep tripping the driver
up in error cases and make things take longer than they should. Add
those in.
All the loops that are part of this commit existed in some form or
another since the r8152 driver was first introduced, though
RTL8152_INACCESSIBLE was known as RTL8152_UNPLUG before commit
715f67f33af4 ("r8152: Rename RTL8152_UNPLUG to RTL8152_INACCESSIBLE")
Fixes: ac718b69301c ("net/usb: new driver for RTL8152")
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As of commit d9962b0d4202 ("r8152: Block future register access if
register access fails") there is a race condition that can happen
between the USB device reset thread and napi_enable() (not) getting
called during rtl8152_open(). Specifically:
* While rtl8152_open() is running we get a register access error
that's _not_ -ENODEV and queue up a USB reset.
* rtl8152_open() exits before calling napi_enable() due to any reason
(including usb_submit_urb() returning an error).
In that case:
* Since the USB reset is perform in a separate thread asynchronously,
it can run at anytime USB device lock is not held - even before
rtl8152_open() has exited with an error and caused __dev_open() to
clear the __LINK_STATE_START bit.
* The rtl8152_pre_reset() will notice that the netif_running() returns
true (since __LINK_STATE_START wasn't cleared) so it won't exit
early.
* rtl8152_pre_reset() will then hang in napi_disable() because
napi_enable() was never called.
We can fix the race by making sure that the r8152 reset routines don't
run at the same time as we're opening the device. Specifically we need
the reset routines in their entirety rely on the return value of
netif_running(). The only way to reliably depend on that is for them
to hold the rntl_lock() mutex for the duration of reset.
Grabbing the rntl_lock() mutex for the duration of reset seems like a
long time, but reset is not expected to be common and the rtnl_lock()
mutex is already held for long durations since the core grabs it
around the open/close calls.
Fixes: d9962b0d4202 ("r8152: Block future register access if register access fails")
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When FIFO reaches near full state, device will issue pause frame.
If pause slot is enabled(set to 1), in this time, device will issue
pause frame only once. But if pause slot is disabled(set to 0), device
will keep sending pause frames until FIFO reaches near empty state.
When pause slot is disabled, if there is no one to handle receive
packets, device FIFO will reach near full state and keep sending
pause frames. That will impact entire local area network.
This issue can be reproduced in Chromebox (not Chromebook) in
developer mode running a test image (and v5.10 kernel):
1) ping -f $CHROMEBOX (from workstation on same local network)
2) run "powerd_dbus_suspend" from command line on the $CHROMEBOX
3) ping $ROUTER (wait until ping fails from workstation)
Takes about ~20-30 seconds after step 2 for the local network to
stop working.
Fix this issue by enabling pause slot to only send pause frame once
when FIFO reaches near full state.
Fixes: f1bce4ad2f1c ("r8169: add support for RTL8125")
Reported-by: Grant Grundler <grundler@chromium.org>
Tested-by: Grant Grundler <grundler@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: ChunHao Lin <hau@realtek.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/20231129155350.5843-1-hau@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
rndis_filter uses utf8s_to_utf16s() which is provided by setting
NLS, so select NLS to fix the build error:
ERROR: modpost: "utf8s_to_utf16s" [drivers/net/hyperv/hv_netvsc.ko] undefined!
Fixes: 1ce09e899d28 ("hyperv: Add support for setting MAC from within guests")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Wei Liu <wei.liu@kernel.org>
Cc: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org> # build-tested
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20231130055853.19069-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When an EEH error is encountered by a PCI adapter, the EEH driver
modifies the PCI channel's state as shown below:
enum {
/* I/O channel is in normal state */
pci_channel_io_normal = (__force pci_channel_state_t) 1,
/* I/O to channel is blocked */
pci_channel_io_frozen = (__force pci_channel_state_t) 2,
/* PCI card is dead */
pci_channel_io_perm_failure = (__force pci_channel_state_t) 3,
};
If the same EEH error then causes the tg3 driver's transmit timeout
logic to execute, the tg3_tx_timeout() function schedules a reset
task via tg3_reset_task_schedule(), which may cause a race condition
between the tg3 and EEH driver as both attempt to recover the HW via
a reset action.
EEH driver gets error event
--> eeh_set_channel_state()
and set device to one of
error state above scheduler: tg3_reset_task() get
returned error from tg3_init_hw()
--> dev_close() shuts down the interface
tg3_io_slot_reset() and
tg3_io_resume() fail to
reset/resume the device
To resolve this issue, we avoid the race condition by checking the PCI
channel state in the tg3_reset_task() function and skip the tg3 driver
initiated reset when the PCI channel is not in the normal state. (The
driver has no access to tg3 device registers at this point and cannot
even complete the reset task successfully without external assistance.)
We'll leave the reset procedure to be managed by the EEH driver which
calls the tg3_io_error_detected(), tg3_io_slot_reset() and
tg3_io_resume() functions as appropriate.
Adding the same checking in tg3_dump_state() to avoid dumping all
device registers when the PCI channel is not in the normal state.
Signed-off-by: Thinh Tran <thinhtr@linux.vnet.ibm.com>
Tested-by: Venkata Sai Duggi <venkata.sai.duggi@ibm.com>
Reviewed-by: David Christensen <drc@linux.vnet.ibm.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20231201001911.656-1-thinhtr@linux.vnet.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If a NIXLF is not attached to a PF/VF device then
nix_get_nixlf function fails and returns proper error
code. But npc_get_default_entry_action does not check it
and uses garbage value in subsequent calls. Fix this
by cheking the return value of nix_get_nixlf.
Fixes: 967db3529eca ("octeontx2-af: add support for multicast/promisc packet replication feature")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All the mailbox messages sent to AF needs to be guarded
by mutex lock. Add the missing lock in otx2_get_pauseparam
function.
Fixes: 75f36270990c ("octeontx2-pf: Support to enable/disable pause frames via ethtool")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We don't have much to say about 9p, even tho it lives under net/.
Avoid CCing netdev.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If fib6_find_prefix() returns NULL, we should silently fallback
using fib6_null_entry regardless of RT6_DEBUG value.
syzbot reported:
WARNING: CPU: 0 PID: 5477 at net/ipv6/ip6_fib.c:1516 fib6_add+0x310d/0x3fa0 net/ipv6/ip6_fib.c:1516
Modules linked in:
CPU: 0 PID: 5477 Comm: syz-executor.0 Not tainted 6.7.0-rc2-syzkaller-00029-g9b6de136b5f0 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 11/10/2023
RIP: 0010:fib6_add+0x310d/0x3fa0 net/ipv6/ip6_fib.c:1516
Code: 00 48 8b 54 24 68 e8 42 22 00 00 48 85 c0 74 14 49 89 c6 e8 d5 d3 c2 f7 eb 5d e8 ce d3 c2 f7 e9 ca 00 00 00 e8 c4 d3 c2 f7 90 <0f> 0b 90 48 b8 00 00 00 00 00 fc ff df 48 8b 4c 24 38 80 3c 01 00
RSP: 0018:ffffc90005067740 EFLAGS: 00010293
RAX: ffffffff89cba5bc RBX: ffffc90005067ab0 RCX: ffff88801a2e9dc0
RDX: 0000000000000000 RSI: 0000000000000001 RDI: 0000000000000000
RBP: ffffc90005067980 R08: ffffffff89cbca85 R09: 1ffff110040d4b85
R10: dffffc0000000000 R11: ffffed10040d4b86 R12: 00000000ffffffff
R13: 1ffff110051c3904 R14: ffff8880206a5c00 R15: ffff888028e1c820
FS: 00007f763783c6c0(0000) GS:ffff8880b9800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f763783bff8 CR3: 000000007f74d000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
__ip6_ins_rt net/ipv6/route.c:1303 [inline]
ip6_route_add+0x88/0x120 net/ipv6/route.c:3847
ipv6_route_ioctl+0x525/0x7b0 net/ipv6/route.c:4467
inet6_ioctl+0x21a/0x270 net/ipv6/af_inet6.c:575
sock_do_ioctl+0x152/0x460 net/socket.c:1220
sock_ioctl+0x615/0x8c0 net/socket.c:1339
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:871 [inline]
__se_sys_ioctl+0xf8/0x170 fs/ioctl.c:857
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x45/0x110 arch/x86/entry/common.c:82
Fixes: 7bbfe00e0252 ("ipv6: fix general protection fault in fib6_add()")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20231129160630.3509216-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On RZ/G3S SMARC Carrier II board having RGMII connections b/w Ethernet
MACs and PHYs it has been discovered that doing unbind/bind for ravb
driver in a loop leads to wrong speed and duplex for Ethernet links and
broken connectivity (the connectivity cannot be restored even with
bringing interface down/up). Before doing unbind/bind the Ethernet
interfaces were configured though systemd. The sh instructions used to
do unbind/bind were:
$ cd /sys/bus/platform/drivers/ravb/
$ while :; do echo 11c30000.ethernet > unbind ; \
echo 11c30000.ethernet > bind; done
It has been discovered that there is a race b/w IOCTLs initialized by
systemd at the response of success binding and the
"ravb_write(ndev, CCC_OPC_RESET, CCC)" call in ravb_remove() as
follows:
1/ as a result of bind success the user space open/configures the
interfaces tough an IOCTL; the following stack trace has been
identified on RZ/G3S:
Call trace:
dump_backtrace+0x9c/0x100
show_stack+0x20/0x38
dump_stack_lvl+0x48/0x60
dump_stack+0x18/0x28
ravb_open+0x70/0xa58
__dev_open+0xf4/0x1e8
__dev_change_flags+0x198/0x218
dev_change_flags+0x2c/0x80
devinet_ioctl+0x640/0x708
inet_ioctl+0x1e4/0x200
sock_do_ioctl+0x50/0x108
sock_ioctl+0x240/0x358
__arm64_sys_ioctl+0xb0/0x100
invoke_syscall+0x50/0x128
el0_svc_common.constprop.0+0xc8/0xf0
do_el0_svc+0x24/0x38
el0_svc+0x34/0xb8
el0t_64_sync_handler+0xc0/0xc8
el0t_64_sync+0x190/0x198
2/ this call may execute concurrently with ravb_remove() as the
unbind/bind operation was executed in a loop
3/ if the operation mode is changed to RESET (through
ravb_write(ndev, CCC_OPC_RESET, CCC) call in ravb_remove())
while the above ravb_open() is in progress it may lead to MAC
(or PHY, or MAC-PHY connection, the right point hasn't been identified
at the moment) to be broken, thus the Ethernet connectivity fails to
restore.
The simple fix for this is to move ravb_write(ndev, CCC_OPC_RESET, CCC))
after unregister_netdev() to avoid resetting the controller while the
netdev interface is still registered.
To avoid future issues in ravb_remove(), the patch follows the proper order
of operations in ravb_remove(): reverse order compared with ravb_probe().
This avoids described races as the IOCTLs as well as unregister_netdev()
(called now at the beginning of ravb_remove()) calls rtnl_lock() before
continuing and IOCTLs check (though devinet_ioctl()) if device is still
registered just after taking the lock:
int devinet_ioctl(struct net *net, unsigned int cmd, struct ifreq *ifr)
{
// ...
rtnl_lock();
ret = -ENODEV;
dev = __dev_get_by_name(net, ifr->ifr_name);
if (!dev)
goto done;
// ...
done:
rtnl_unlock();
out:
return ret;
}
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In case ravb_phy_start() returns with error the settings applied in
ravb_dmac_init() are not reverted (e.g. config mode). For this call
ravb_stop_dma() on failure path of ravb_open().
Fixes: a0d2f20650e8 ("Renesas Ethernet AVB PTP clock driver")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
ravb_phy_start() may fail. If that happens, the TX queues will remain
started. Thus, move the netif_tx_start_all_queues() after PHY is
successfully initialized.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Hardware manual of RZ/G3S (and RZ/G2L) specifies the following on the
description of CXR35 register (chapter "PHY interface select register
(CXR35)"): "After release reset, make write-access to this register before
making write-access to other registers (except MDIOMOD). Even if not need
to change the value of this register, make write-access to this register
at least one time. Because RGMII/MII MODE is recognized by accessing this
register".
The setup procedure for EMAC module (chapter "Setup procedure" of RZ/G3S,
RZ/G2L manuals) specifies the E-MAC.CXR35 register is the first EMAC
register that is to be configured.
Note [A] from chapter "PHY interface select register (CXR35)" specifies
the following:
[A] The case which CXR35 SEL_XMII is used for the selection of RGMII/MII
in APB Clock 100 MHz.
(1) To use RGMII interface, Set ‘H’03E8_0000’ to this register.
(2) To use MII interface, Set ‘H’03E8_0002’ to this register.
Take into account these indication.
Fixes: 1089877ada8d ("ravb: Add RZ/G2L MII interface support")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
pm_runtime_get_sync() may return an error. In case it returns with an error
dev->power.usage_count needs to be decremented. pm_runtime_resume_and_get()
takes care of this. Thus use it.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
reset_control_deassert() could return an error. Some devices cannot work
if reset signal de-assert operation fails. To avoid this check the return
code of reset_control_deassert() in ravb_probe() and take proper action.
Along with it, the free_netdev() call from the error path was moved after
reset_control_assert() on its own label (out_free_netdev) to free
netdev in case reset_control_deassert() fails.
Fixes: 0d13a1a464a0 ("ravb: Add reset support")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Since pci_free_irq_vectors() set pdev->msix_enabled as 0 in the
calling of pci_msix_shutdown(), wx->msix_entries is never freed.
Reordering the lines to fix the memory leak.
Cc: stable@vger.kernel.org
Fixes: 3f703186113f ("net: libwx: Add irq flow functions")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Link: https://lore.kernel.org/r/20231128095928.1083292-1-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is an error when an interface has the following conditions:
- PF is in an aggregate (bond)
- PF has VFs created on it
- bond is in a state where it is failed-over to the secondary interface
- A VF reset is issued on one or more of those VFs
The issue is generated by the originating PF trying to rebuild or
reconfigure the VF resources. Since the bond is failed over to the
secondary interface the queue contexts are in a modified state.
To fix this issue, have the originating interface reclaim its resources
prior to the tear-down and rebuild or reconfigure. Then after the process
is complete, move the resources back to the currently active interface.
There are multiple paths that can be used depending on what triggered the
event, so create a helper function to move the queues and use paired calls
to the helper (back to origin, process, then move back to active interface)
under the same lag_mutex lock.
Fixes: 1e0f9881ef79 ("ice: Flesh out implementation of support for SRIOV on bonded interface")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://lore.kernel.org/r/20231127212340.1137657-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This adds a test where both pairs of a af_unix paired socket are put into a
BPF map. This ensures that when we tear down the af_unix pair we don't have
any issues on sockmap side with ordering and reference counting.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/20231129012557.95371-3-john.fastabend@gmail.com
|
|
AF_UNIX stream sockets are a paired socket. So sending on one of the pairs
will lookup the paired socket as part of the send operation. It is possible
however to put just one of the pairs in a BPF map. This currently increments
the refcnt on the sock in the sockmap to ensure it is not free'd by the
stack before sockmap cleans up its state and stops any skbs being sent/recv'd
to that socket.
But we missed a case. If the peer socket is closed it will be free'd by the
stack. However, the paired socket can still be referenced from BPF sockmap
side because we hold a reference there. Then if we are sending traffic through
BPF sockmap to that socket it will try to dereference the free'd pair in its
send logic creating a use after free. And following splat:
[59.900375] BUG: KASAN: slab-use-after-free in sk_wake_async+0x31/0x1b0
[59.901211] Read of size 8 at addr ffff88811acbf060 by task kworker/1:2/954
[...]
[59.905468] Call Trace:
[59.905787] <TASK>
[59.906066] dump_stack_lvl+0x130/0x1d0
[59.908877] print_report+0x16f/0x740
[59.910629] kasan_report+0x118/0x160
[59.912576] sk_wake_async+0x31/0x1b0
[59.913554] sock_def_readable+0x156/0x2a0
[59.914060] unix_stream_sendmsg+0x3f9/0x12a0
[59.916398] sock_sendmsg+0x20e/0x250
[59.916854] skb_send_sock+0x236/0xac0
[59.920527] sk_psock_backlog+0x287/0xaa0
To fix let BPF sockmap hold a refcnt on both the socket in the sockmap and its
paired socket. It wasn't obvious how to contain the fix to bpf_unix logic. The
primarily problem with keeping this logic in bpf_unix was: In the sock close()
we could handle the deref by having a close handler. But, when we are destroying
the psock through a map delete operation we wouldn't have gotten any signal
thorugh the proto struct other than it being replaced. If we do the deref from
the proto replace its too early because we need to deref the sk_pair after the
backlog worker has been stopped.
Given all this it seems best to just cache it at the end of the psock and eat 8B
for the af_unix and vsock users. Notice dgram sockets are OK because they handle
locking already.
Fixes: 94531cfcbe79 ("af_unix: Add unix_stream_proto for sockmap")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/20231129012557.95371-2-john.fastabend@gmail.com
|
|
struct ynl_req_state carries reply-related info from generated code
into generic YNL code. While we don't need reply info to execute
a request without a reply, we still need to pass in the struct, because
it's also where we get the pointer to struct ynl_sock from. Passing NULL
results in crashes if kernel returns an error or an unexpected reply.
Fixes: dc0956c98f11 ("tools: ynl-gen: move the response reading logic into YNL")
Link: https://lore.kernel.org/r/20231126225858.2144136-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The default dump handler needs to clear ret before returning.
Otherwise if the last interface returns an inconsequential
error this error will propagate to user space.
This may confuse user space (ethtool CLI seems to ignore it,
but YNL doesn't). It will also terminate the dump early
for mutli-skb dump, because netlink core treats EOPNOTSUPP
as a real error.
Fixes: 728480f12442 ("ethtool: default handlers for GET requests")
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20231126225806.2143528-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix races between ravb_tx_timeout_work() and functions of net_device_ops
and ethtool_ops by using rtnl_trylock() and rtnl_unlock(). Note that
since ravb_close() is under the rtnl lock and calls cancel_work_sync(),
ravb_tx_timeout_work() should calls rtnl_trylock(). Otherwise, a deadlock
may happen in ravb_tx_timeout_work() like below:
CPU0 CPU1
ravb_tx_timeout()
schedule_work()
...
__dev_close_many()
// Under rtnl lock
ravb_close()
cancel_work_sync()
// Waiting
ravb_tx_timeout_work()
rtnl_lock()
// This is possible to cause a deadlock
If rtnl_trylock() fails, rescheduling the work with sleep for 1 msec.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20231127122420.3706751-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ndo_stop() is RTNL-protected by net core, and the worker function takes
RTNL as well. Therefore we will deadlock when trying to execute a
pending work synchronously. To fix this execute any pending work
asynchronously. This will do no harm because netif_running() is false
in ndo_stop(), and therefore the work function is effectively a no-op.
However we have to ensure that no task is running or pending after
rtl_remove_one(), therefore add a call to cancel_work_sync().
Fixes: abe5fc42f9ce ("r8169: use RTNL to protect critical sections")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/12395867-1d17-4cac-aa7d-c691938fcddf@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The original change results in a deadlock if jumbo mtu mode is used.
Reason is that the phydev lock is held when rtl_reset_work() is called
here, and rtl_jumbo_config() calls phy_start_aneg() which also tries
to acquire the phydev lock. Fix this by calling rtl_reset_work()
asynchronously.
Fixes: 621735f59064 ("r8169: fix rare issue with broken rx after link-down on RTL8125")
Reported-by: Ian Chen <free122448@hotmail.com>
Tested-by: Ian Chen <free122448@hotmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/caf6a487-ef8c-4570-88f9-f47a659faf33@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When a task needs to accept memory it will scan the accepting_list
to see if any ranges already being processed by other tasks overlap
with its range. Due to an off-by-one in the range comparisons, a task
might falsely determine that an overlapping range is being accepted,
leading to an unnecessary delay before it begins processing the range.
Fix the off-by-one in the range comparison to prevent this and slightly
improve performance.
Fixes: 50e782a86c98 ("efi/unaccepted: Fix soft lockups caused by parallel memory acceptance")
Link: https://lore.kernel.org/linux-mm/20231101004523.vseyi5bezgfaht5i@amd.com/T/#me2eceb9906fcae5fe958b3fe88e41f920f8335b6
Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Michael Roth <michael.roth@amd.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
Previously, one-element and zero-length arrays were treated as true
flexible arrays, even though they are actually "fake" flex arrays.
The __randomize_layout would leave them untouched at the end of the
struct, similarly to proper C99 flex-array members.
However, this approach changed with commit 1ee60356c2dc ("gcc-plugins:
randstruct: Only warn about true flexible arrays"). Now, only C99
flexible-array members will remain untouched at the end of the struct,
while one-element and zero-length arrays will be subject to randomization.
Fix a `__randomize_layout` crash in `struct neighbour` by transforming
zero-length array `primary_key` into a proper C99 flexible-array member.
Fixes: 1ee60356c2dc ("gcc-plugins: randstruct: Only warn about true flexible arrays")
Closes: https://lore.kernel.org/linux-hardening/20231124102458.GB1503258@e124191.cambridge.arm.com/
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Joey Gouly <joey.gouly@arm.com>
Link: https://lore.kernel.org/r/ZWJoRsJGnCPdJ3+2@work
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
TC ingress policer rules depends on interface receive queue
contexts since the bandwidth profiles are attached to RQ
contexts. When an interface is brought down all the queue
contexts are freed. This in turn frees bandwidth profiles in
hardware causing ingress police rules non-functional after
the interface is brought up. Fix this by applying all the ingress
police rules config to hardware in otx2_open. Also allow
adding ingress rules only when interface is running
since no contexts exist for the interface when it is down.
Fixes: 68fbff68dbea ("octeontx2-pf: Add police action for TC flower")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Link: https://lore.kernel.org/r/1700930217-5707-1-git-send-email-sbhatta@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When more than 64 VFs are enabled for a PF then mbox communication
between VF and PF is not working as mbox work queueing for few VFs
are skipped due to wrong calculation of VF numbers.
Fixes: d424b6c02415 ("octeontx2-pf: Enable SRIOV and added VF mbox handling")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Link: https://lore.kernel.org/r/1700930042-5400-1-git-send-email-sbhatta@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Commit aeb18dd07692 ("net: stmmac: xgmac: Disable MMC interrupts
by default") tries to disable MMC interrupts to avoid a storm of
unhandled interrupts, but leaves the FPE(Frame Preemption) MMC
interrupts enabled, FPE MMC interrupts can cause the same problem.
Now we mask FPE TX and RX interrupts to disable all MMC interrupts.
Fixes: aeb18dd07692 ("net: stmmac: xgmac: Disable MMC interrupts by default")
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://lore.kernel.org/r/20231125060126.2328690-1-0x1207@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
A loop in rvu_mbox_handler_nix_bandprof_free() contains
a break if (idx == MAX_BANDPROF_PER_PFFUNC),
but if idx may reach MAX_BANDPROF_PER_PFFUNC
buffer '(*req->prof_idx)[layer]' overflow happens before that check.
The patch moves the break to the
beginning of the loop.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: e8e095b3b370 ("octeontx2-af: cn10k: Bandwidth profiles config support").
Signed-off-by: Elena Salomatkina <elena.salomatkina.cmc@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Link: https://lore.kernel.org/r/20231124210802.109763-1-elena.salomatkina.cmc@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Same init_rng() in both tests. The function reads /dev/urandom to
initialize srand(). In case of failure, it falls back onto the
entropy in the uninitialized variable. Not sure if this is on purpose.
But failure reading urandom should be rare, so just fail hard. While
at it, convert to getrandom(). Which man 4 random suggests is simpler
and more robust.
mptcp_inq.c:525:6:
mptcp_connect.c:1131:6:
error: variable 'foo' is used uninitialized
whenever 'if' condition is false
[-Werror,-Wsometimes-uninitialized]
Fixes: 048d19d444be ("mptcp: add basic kselftest for mptcp")
Fixes: b51880568f20 ("selftests: mptcp: add inq test case")
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: Willem de Bruijn <willemb@google.com>
----
When input is randomized because this is expected to meaningfully
explore edge cases, should we also add
1. logging the random seed to stdout and
2. adding a command line argument to replay from a specific seed
I can do this in net-next, if authors find it useful in this case.
Reviewed-by: Matthieu Baerts <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20231124171645.1011043-5-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove an unused variable.
diag_uid.c:151:24:
error: unused variable 'udr'
[-Werror,-Wunused-variable]
Fixes: ac011361bd4f ("af_unix: Add test for sock_diag and UDIAG_SHOW_UID.")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20231124171645.1011043-4-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Signedness of char is signed on x86_64, but unsigned on arm64.
Fix the warning building cmsg_sender.c on signed platforms or
forced with -fsigned-char:
msg_sender.c:455:12:
error: implicit conversion from 'int' to 'char'
changes value from 128 to -128
[-Werror,-Wconstant-conversion]
buf[0] = ICMPV6_ECHO_REQUEST;
constant ICMPV6_ECHO_REQUEST is 128.
Link: https://lwn.net/Articles/911914
Fixes: de17e305a810 ("selftests: net: cmsg_sender: support icmp and raw sockets")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20231124171645.1011043-3-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix a small compiler warning.
nr_process must be a signed long: it is assigned a signed long by
strtol() and is compared against LONG_MIN and LONG_MAX.
ipsec.c:2280:65:
error: result of comparison of constant -9223372036854775808
with expression of type 'unsigned int' is always false
[-Werror,-Wtautological-constant-out-of-range-compare]
if ((errno == ERANGE && (nr_process == LONG_MAX || nr_process == LONG_MIN))
Fixes: bc2652b7ae1e ("selftest/net/xfrm: Add test for ipsec tunnel")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Dmitry Safonov <0x7f454c46@gmail.com>
Link: https://lore.kernel.org/r/20231124171645.1011043-2-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The IFLA_NETKIT_PEER_INFO attribute can only be used during device
creation, but not via changelink callback. Hence reject it there.
Fixes: 35dfaad7188c ("netkit, bpf: Add bpf programmable net device")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Cc: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/e86a277a1e8d3b19890312779e42f790b0605ea4.1701115314.git.daniel@iogearbox.net
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
|
|
It was a mistake to prefer polling based mode when setting a performance
level for a domain. Let's instead rely on the protocol to decide what is
best and thus avoid polling when possible.
Reported-by: Nikunj Kela <nkela@quicinc.com>
Fixes: 2af23ceb8624 ("pmdomain: arm: Add the SCMI performance domain")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/20231127135033.136442-1-ulf.hansson@linaro.org
|
|
The debugfs files for netdevs (sdata) and links are removed
with the wiphy mutex held, which may deadlock. Use the new
wiphy locked debugfs to avoid that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The read is currently with RCU and the write can deadlock,
convert both for the sake of illustration.
Make mac80211 depend on cfg80211 debugfs to get the helpers,
but mac80211 debugfs without it does nothing anyway. This
also required some adjustments in ath9k.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add wrappers for debugfs files that should be called with
the wiphy mutex held, while the file is also to be removed
under the wiphy mutex. This could otherwise deadlock when
a file is trying to acquire the wiphy mutex while the code
removing it holds the mutex but waits for the removal.
This actually works by pushing the execution of the read
or write handler to a wiphy work that can be cancelled
using the debugfs cancellation API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In some cases there might be longer-running hardware accesses
in debugfs files, or attempts to acquire locks, and we want
to still be able to quickly remove the files.
Introduce a cancellations API to use inside the debugfs handler
functions to be able to cancel such operations on a per-file
basis.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When you take a lock in a debugfs handler but also try
to remove the debugfs file under that lock, things can
deadlock since the removal has to wait for all users
to finish.
Add lockdep annotations in debugfs_file_get()/_put()
to catch such issues.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
Michal Swiatkowski
Zhipeng Lu
Jianheng Zhang
Naveen Mamindlapalli
Thomas Reichinger
Daniel Borkmann
Douglas Anderson
ChunHao Lin
Randy Dunlap
Thinh Tran
Subbaraya Sundeep
Jakub Kicinski
Eric Dumazet
Claudiu Beznea
Jiawen Wu
Dave Ertman
John Fastabend
Yoshihiro Shimoda
Heiner Kallweit
Michael Roth
Gustavo A. R. Silva
Geetha sowjanya
Furong Xu
Elena Salomatkina
Willem de Bruijn
Ulf Hansson
Johannes Berg