| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
If first_sg and last_sg wraps around in the scatterlist ring, then we
need to account for that in the shift as well. E.g. crafting such msgs
where this is the case leads to a hang as shift becomes negative. E.g.
consider the following scenario:
first_sg := 14 |=> shift := -12 msg->sg_start := 10
last_sg := 3 | msg->sg_end := 5
round 1: i := 15, move_from := 3, sg[15] := sg[ 3]
round 2: i := 0, move_from := -12, sg[ 0] := sg[-12]
round 3: i := 1, move_from := -11, sg[ 1] := sg[-11]
round 4: i := 2, move_from := -10, sg[ 2] := sg[-10]
[...]
round 13: i := 11, move_from := -1, sg[ 2] := sg[ -1]
round 14: i := 12, move_from := 0, sg[ 2] := sg[ 0]
round 15: i := 13, move_from := 1, sg[ 2] := sg[ 1]
round 16: i := 14, move_from := 2, sg[ 2] := sg[ 2]
round 17: i := 15, move_from := 3, sg[ 2] := sg[ 3]
[...]
This means we will loop forever and never hit the msg->sg_end condition
to break out of the loop. When we see that the ring wraps around, then
the shift should be MAX_SKB_FRAGS - first_sg + last_sg - 1. Meaning,
the remainder slots from the tail of the ring and the head until last_sg
combined.
Fixes: 015632bb30da ("bpf: sk_msg program helper bpf_sk_msg_pull_data")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
In the current code, msg->data is set as sg_virt(&sg[i]) + start - offset
and msg->data_end relative to it as msg->data + bytes. Using iterator i
to point to the updated starting scatterlist element holds true for some
cases, however not for all where we'd end up pointing out of bounds. It
is /correct/ for these ones:
1) When first finding the starting scatterlist element (sge) where we
find that the page is already privately owned by the msg and where
the requested bytes and headroom fit into the sge's length.
However, it's /incorrect/ for the following ones:
2) After we made the requested area private and updated the newly allocated
page into first_sg slot of the scatterlist ring; when we find that no
shift repair of the ring is needed where we bail out updating msg->data
and msg->data_end. At that point i will point to last_sg, which in this
case is the next elem of first_sg in the ring. The sge at that point
might as well be invalid (e.g. i == msg->sg_end), which we use for
setting the range of sg_virt(&sg[i]). The correct one would have been
first_sg.
3) Similar as in 2) but when we find that a shift repair of the ring is
needed. In this case we fix up all sges and stop once we've reached the
end. In this case i will point to will point to the new msg->sg_end,
and the sge at that point will be invalid. Again here the requested
range sits in first_sg.
Fixes: 015632bb30da ("bpf: sk_msg program helper bpf_sk_msg_pull_data")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
While recently going over bpf_msg_pull_data(), I noticed three
issues which are fixed in here:
1) When we attempt to find the first scatterlist element (sge)
for the start offset, we add len to the offset before we check
for start < offset + len, whereas it should come after when
we iterate to the next sge to accumulate the offsets. For
example, given a start offset of 12 with a sge length of 8
for the first sge in the list would lead us to determine this
sge as the first sge thinking it covers first 16 bytes where
start is located, whereas start sits in subsequent sges so
we would end up pulling in the wrong data.
2) After figuring out the starting sge, we have a short-cut test
in !msg->sg_copy[i] && bytes <= len. This checks whether it's
not needed to make the page at the sge private where we can
just exit by updating msg->data and msg->data_end. However,
the length test is not fully correct. bytes <= len checks
whether the requested bytes (end - start offsets) fit into the
sge's length. The part that is missing is that start must not
be sge length aligned. Meaning, the start offset into the sge
needs to be accounted as well on top of the requested bytes
as otherwise we can access the sge out of bounds. For example
the sge could have length of 8, our requested bytes could have
length of 8, but at a start offset of 4, so we also would need
to pull in 4 bytes of the next sge, when we jump to the out
label we do set msg->data to sg_virt(&sg[i]) + start - offset
and msg->data_end to msg->data + bytes which would be oob.
3) The subsequent bytes < copy test for finding the last sge has
the same issue as in point 2) but also it tests for less than
rather than less or equal to. Meaning if the sge length is of
8 and requested bytes of 8 while having the start aligned with
the sge, we would unnecessarily go and pull in the next sge as
well to make it private.
Fixes: 015632bb30da ("bpf: sk_msg program helper bpf_sk_msg_pull_data")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Currently, when a redirect occurs in sockmap and an error occurs in
the redirect call we unwind the scatterlist once in the error path
of bpf_tcp_sendmsg_do_redirect() and then again in sendmsg(). Then
in the error path of sendmsg we decrement the copied count by the
send size.
However, its possible we partially sent data before the error was
generated. This can happen if do_tcp_sendpages() partially sends the
scatterlist before encountering a memory pressure error. If this
happens we need to decrement the copied value (the value tracking
how many bytes were actually sent to TCP stack) by the number of
remaining bytes _not_ the entire send size. Otherwise we risk
confusing userspace.
Also we don't need two calls to free the scatterlist one is
good enough. So remove the one in bpf_tcp_sendmsg_do_redirect() and
then properly reduce copied by the number of remaining bytes which
may in fact be the entire send size if no bytes were sent.
To do this use bool to indicate if free_start_sg() should do mem
accounting or not.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Building the newly introduced BPF_PROG_TYPE_SK_REUSEPORT leads to
a compile time error when building with clang:
net/core/filter.o: In function `sk_reuseport_convert_ctx_access':
../net/core/filter.c:7284: undefined reference to `__compiletime_assert_7284'
It seems that clang has issues resolving hweight_long at compile
time. Since SK_FL_PROTO_MASK is a constant, we can use the interface
for known constant arguments which works fine with clang.
Fixes: 2dbb9b9e6df6 ("bpf: Introduce BPF_PROG_TYPE_SK_REUSEPORT")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
In bpf_tcp_recvmsg() we first took a reference on the psock, however
once we find that there are skbs in the normal socket's receive queue
we return with processing them through tcp_recvmsg(). Problem is that
we leak the taken reference on the psock in that path. Given we don't
really do anything with the psock at this point, move the skb_queue_empty()
test before we fetch the psock to fix this case.
Fixes: 8934ce2fd081 ("bpf: sockmap redirect ingress support")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
bpf_tcp_close() we pop the psock linkage to a map via psock_map_pop().
A parallel update on the sock hash map can happen between psock_map_pop()
and lookup_elem_raw() where we override the element under link->hash /
link->key. In bpf_tcp_close()'s lookup_elem_raw() we subsequently only
test whether an element is present, but we do not test whether the
element is infact the element we were looking for.
We lock the sock in bpf_tcp_close() during that time, so do we hold
the lock in sock_hash_update_elem(). However, the latter locks the
sock which is newly updated, not the one we're purging from the hash
table. This means that while one CPU is doing the lookup from bpf_tcp_close(),
another CPU is doing the map update in parallel, dropped our sock from
the hlist and released the psock.
Subsequently the first CPU will find the new sock and attempts to drop
and release the old sock yet another time. Fix is that we need to check
the elements for a match after lookup, similar as we do in the sock map.
Note that the hash tab elems are freed via RCU, so access to their
link->hash / link->key is fine since we're under RCU read side there.
Fixes: e9db4ef6bf4c ("bpf: sockhash fix omitted bucket lock in sock_close")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
In IPv4, the newly introduced rdma_read_gids is used to read the SGID/DGID
for the connection which returns GID correctly for RoCE transport as well.
In IPv6, rdma_read_gids is also used. The following are why rdma_read_gids
is introduced.
rdma_addr_get_dgid() for RoCE for client side connections returns MAC
address, instead of DGID.
rdma_addr_get_sgid() for RoCE doesn't return correct SGID for IPv6 and
when more than one IP address is assigned to the netdevice.
So the transport agnostic rdma_read_gids() API is provided by rdma_cm
module.
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 52638f71fcff ("dsa: Move gpio reset into switch driver")
moved the GPIO handling into the switch drivers but forgot
to remove the GPIO header includes.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In function tipc_dest_push, the 32bit variables 'node' and 'port'
are stored separately in uppper and lower part of 64bit 'value'.
Then this value is assigned to dst->value which is a union like:
union
{
struct {
u32 port;
u32 node;
};
u64 value;
}
This works on little-endian machines like x86 but fails on big-endian
machines.
The fix remove the 'value' stack parameter and even the 'value'
member of the union in tipc_dest, assign the 'node' and 'port' member
directly with the input parameter to avoid the endian issue.
Fixes: a80ae5306a73 ("tipc: improve destination linked list")
Signed-off-by: Zhenbo Gao <zhenbo.gao@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Haiqing Bai <Haiqing.Bai@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When chain 0 was implicitly created, removal of non-existent filter from
chain 0 gave -ENOENT. Once chain 0 became non-implicit, the same call is
giving -EINVAL. Fix this by returning -ENOENT in that case.
Reported-by: Roman Mashak <mrv@mojatatu.com>
Fixes: f71e0ca4db18 ("net: sched: Avoid implicit chain 0 creation")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead "Cannot find" say "Cannot create".
Fixes: c35a4acc2985 ("net: sched: cls_api: handle generic cls errors")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After erspan_ver is introudced, if erspan_ver is not set in iproute, its
value will be left 0 by default. Since Commit 02f99df1875c ("erspan: fix
invalid erspan version."), it has broken the traffic due to the version
check in erspan_xmit if users are not aware of 'erspan_ver' param, like
using an old version of iproute.
To fix this compatibility problem, it sets erspan_ver to 1 by default
when adding an erspan dev in erspan_setup. Note that we can't do it in
ipgre_netlink_parms, as this function is also used by ipgre_changelink.
Fixes: 02f99df1875c ("erspan: fix invalid erspan version.")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After changing rhashtable_walk_start to return void, start_fail would
never be set other value than 0, and the checking for start_fail is
pointless, so remove it.
Fixes: 97a6ec4ac021 ("rhashtable: Change rhashtable_walk_start to return void")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As Marcelo noticed, in sctp_transport_get_next, it is iterating over
transports but then also accessing the association directly, without
checking any refcnts before that, which can cause an use-after-free
Read.
So fix it by holding transport before accessing the association. With
that, sctp_transport_hold calls can be removed in the later places.
Fixes: 626d16f50f39 ("sctp: export some apis or variables for sctp_diag and reuse some for proc")
Reported-by: syzbot+fe62a0c9aa6a85c6de16@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The email was botched in one entry, and I also forgot to update the
location of the git tree. It'll be under the linux-block umbrella, just
with different branches.
Reported-by: Baruch Siach <baruch@tkos.co.il>
Fixes: 7634ccd2da97 ("libata: maintainership update")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Via u32_change(), TCA_U32_SEL has an unspecified type in the netlink
policy, so max length isn't enforced, only minimum. This means nkeys
(from userspace) was being trusted without checking the actual size of
nla_len(), which could lead to a memory over-read, and ultimately an
exposure via a call to u32_dump(). Reachability is CAP_NET_ADMIN within
a namespace.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Trivial fix to spelling mistake in DP_ERR error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We don't wakeup the virtqueue if the first byte of pending iova range
is the last byte of the range we just got updated. This will lead a
virtqueue to wait for IOTLB updating forever. Fixing by correct the
check and wake up the virtqueue in this case.
Fixes: 6b1e6cc7855b ("vhost: new device IOTLB API")
Reported-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Tested-by: Peter Xu <peterx@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
qlge_fix_features() is not supposed to modify hardware or
driver state, rather it is supposed to only fix requested
fetures bits. Currently qlge_fix_features() also goes for
interface down and up unnecessarily if there is not even
any change in features set.
This patch changes/fixes following -
1) Move reload of interface or device re-config from
qlge_fix_features() to qlge_set_features().
2) Reload of interface in qlge_set_features() only if
relevant feature bit (NETIF_F_HW_VLAN_CTAG_RX) is changed.
3) Get rid of qlge_fix_features() since driver is not really
required to fix any features bit.
Signed-off-by: Manish <manish.chopra@cavium.com>
Reviewed-by: Benjamin Poirier <bpoirier@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
macb_reset_hw() is called from macb_close() and indirectly from
macb_open(). macb_reset_hw() zeroes the NCR register, including the MPE
(Management Port Enable) bit.
This will prevent accessing any other PHYs for other Ethernet MACs on
the MDIO bus, which remains registered at macb_reset_hw() time, until
macb_init_hw() is called from macb_open() which sets the MPE bit again.
I.e. currently the MDIO bus has a short disruption at open time and is
disabled at close time until the interface is opened again.
Fix that by only touching the RE and TE bits when enabling and disabling
RX/TX.
v2: Make macb_init_hw() NCR write a single statement.
Fixes: 6c36a7074436 ("macb: Use generic PHY layer")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit bde4975310eb1982bd0bbff673989052d92fd481.
All legacy clock implementations now implement clk_set_rate() (Some
implementations may be dummies, though).
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Arnd Bergmann <arnd@arnd.de>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 739de9a1563a ("net: macb: Reorganize macb_mii bringup") broke
initializing macb on the EVB-KSZ9477 eval board.
There, of_mdiobus_register was called even for the fixed-link representing
the RGMII-link to the switch with the result that the driver attempts to
enumerate PHYs on a non-existent MDIO bus:
libphy: MACB_mii_bus: probed
mdio_bus f0028000.ethernet-ffffffff: fixed-link has invalid PHY address
mdio_bus f0028000.ethernet-ffffffff: scan phy fixed-link at address 0
[snip]
mdio_bus f0028000.ethernet-ffffffff: scan phy fixed-link at address 31
The "MDIO" bus registration succeeds regardless, having claimed the reset GPIO,
and calling of_phy_register_fixed_link later on fails because it tries
to claim the same GPIO:
macb f0028000.ethernet: broken fixed-link specification
Fix this by registering the fixed-link before calling mdiobus_register.
Fixes: 739de9a1563a ("net: macb: Reorganize macb_mii bringup")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a bridge device is removed, the VLANs are flushed from each
configured port. This causes the ports to decrement the reference count
on the associated FIDs (filtering identifier). If the reference count of
a FID is 1 and it has a RIF (router interface), then this RIF is
destroyed.
However, if no port is member in the VLAN for which a RIF exists, then
the RIF will continue to exist after the removal of the bridge. To
reproduce:
# ip link add name br0 type bridge vlan_filtering 1
# ip link set dev swp1 master br0
# ip link add link br0 name br0.10 type vlan id 10
# ip address add 192.0.2.0/24 dev br0.10
# ip link del dev br0
The RIF associated with br0.10 continues to exist.
Fix this by iterating over all the bridge device uppers when it is
destroyed and take care of destroying their RIFs.
Fixes: 99f44bb3527b ("mlxsw: spectrum: Enable L3 interfaces on top of bridge devices")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is not normally noticeable, but repeated forks are unnecessarily
expensive because they repeatedly dirty the parent page tables during
the page table copy operation.
It's trivial to just avoid write protecting the page table entry if it
was already not writable.
This patch was inspired by
https://bugzilla.kernel.org/show_bug.cgi?id=200447
which points to an ancient "waste time re-doing fork" issue in the
presence of lots of signals.
That bug was fixed by Eric Biederman's signal handling series
culminating in commit c3ad2c3b02e9 ("signal: Don't restart fork when
signals come in"), but the unnecessary work for repeated forks is still
work just fixing, particularly since the fix is trivial.
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
At the point where r is being checked for different values, r is always
going to be equal to 2 as the previous if statements jump to end or end1
if r is not 2. Hence the assignment to err can be simplified to just
err an assignment without any checks on the value or r.
Detected by CoverityScan, CID#1226737 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Tejun Heo wrote:
>
> I asked Jens whether he could take care of the libata tree and he
> thankfully agreed, so, from now on, Jens will be the libata
> maintainer.
>
> Thanks a lot!
Thanks for your work in this area. I still remember the first linux
storage summit we did in Vancouver 2001, Tejun was invited to talk about
his libata error handling work. Before that, it was basically a crap
shoot if we recovered properly or not... A lot of water has flown under
the bridge since then!
Here's an "official" patch. Linus, can you apply it?
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 9b10df596bd4 ("i40e: use WARN_ONCE to replace the commented
BUG_ON size check") introduced a warning check to make sure
that the size of the stat strings was always the expected value. This
code accidentally inverted the check of the data pointer. Fix this so
that we accurately count the size of the stats we copied in.
This fixes an erroneous WARN kernel splat that occurs when requesting
ethtool statistics.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Tested-by: Mauro S M Rodrigues <maurosr@linux.vnet.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If interface is connected to switch port configured for DCB there are
TX timeouts when bringing up interface. Problem started appearing after
adding in i40e driver code mqprio hardware offload mode. In function
i40e_vsi_configure_bw_alloc was added resetting BW rate which should
be executing when mqprio qdisc is removed but was also when there was
no mqprio qdisc added and DCB was enabled. In this patch was added
additional check for DCB flag so now when DCB is enabled the correct
DCB configs from before mqprio patch are restored.
Signed-off-by: Martyna Szapar <martyna.szapar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Since VFLR doesn't clear VFMBMEM (VF Mailbox Memory)
and is not re-enabling queues correctly we should fix
this behavior.
Signed-off-by: Sebastian Basierski <sebastianx.basierski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
These changes address comments by Jakub Kicinski on
commit 38b7e7f8ae82 ("ixgbe: Do not allow LRO or MTU change with XDP").
Change the MTU check with XDP to allow any supported value and only
reject those outside of the range as opposed to rejecting any change
when XDP is active. In situations where MTU size is not supported,
return -EINVAL instead of -EPERM.
Add checks when enabling SRIOV, DCB, or adding L2FW offloaded device
as they are not supported with XDP.
CC: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
ixgbe_fcoe_ddp_setup(), ixgbe_setup_fcoe_ddp_resources() and
ixgbe_sw_init() are never called in atomic context.
They call kmalloc(), dma_pool_alloc() and kzalloc() with GFP_ATOMIC,
which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Acked-by: Sebastian Basierski <sebastianx.basierski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
igb_integrated_phy_loopback() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
igb_sw_init() is never called in atomic context.
It calls kzalloc() and kcalloc() with GFP_ATOMIC, which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
On i210, Launchtime (TxTime) requires the usage of an "Advanced
Transmit Context Descriptor" for retrieving the timestamp of a packet.
The igb driver correctly builds such descriptor on the segmentation
flow (i.e. igb_tso()) or on the checksum one (i.e. igb_tx_csum()), but the
feature is broken for AF_PACKET if the IGB_TX_FLAGS_VLAN is not set,
which happens due to an early return on igb_tx_csum().
This flag is only set by the kernel when a VLAN interface is used,
thus we can't just rely on it. Here we are fixing this issue by checking
if launchtime is enabled for the current tx_ring before performing the
early return.
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In 'e1000_set_ringparam()', the tx_ring and rx_ring are updated with new value
and the old tx/rx rings are freed only when the device is up. There are resource
leaks on old tx/rx rings when the device is not up. This bug is reported by COD,
a tool for testing kernel module binaries I am building.
This patch fixes the bug by always calling 'kfree()' on old tx/rx rings in
'e1000_set_ringparam()'.
Signed-off-by: Bo Chen <chenbo@pdx.edu>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When the device is not up, the call to 'e1000_up()' from the error handling path
of 'e1000_set_ringparam()' causes a kernel oops with a null-pointer
dereference. The null-pointer dereference is triggered in function
'e1000_alloc_rx_buffers()' at line 'buffer_info = &rx_ring->buffer_info[i]'.
This bug was reported by COD, a tool for testing kernel module binaries I am
building. This bug was also detected by KFI from Dr. Kai Cong.
This patch fixes the bug by checking on 'netif_running()' before calling
'e1000_up()' in 'e1000_set_ringparam()'.
Signed-off-by: Bo Chen <chenbo@pdx.edu>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Use dma_zalloc_coherent instead of dma_alloc_coherent
followed by memset 0.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Enabling the interrupt early, before power has been applied to the
device, can result in an interrupt being delivered too early if:
- the IOMMU shares an interrupt with a VOP
- the VOP has a pending interrupt (after a kexec, for example)
In these conditions, we end-up taking the interrupt without
the IOMMU being ready to handle the interrupt (not powered on).
Moving the interrupt request past the pm_runtime_enable() call
makes sure we can at least access the IOMMU registers. Note that
this is only a partial fix, and that the VOP interrupt will still
be screaming until the VOP driver kicks in, which advocates for
a more synchronized interrupt enabling/disabling approach.
Fixes: 0f181d3cf7d98 ("iommu/rockchip: Add runtime PM support")
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
pm_runtime_get_if_in_use can fail: either PM has been disabled
altogether (-EINVAL), or the device hasn't been enabled yet (0).
Sadly, the Rockchip IOMMU driver tends to conflate the two things
by considering a non-zero return value as successful.
This has the consequence of hiding other bugs, so let's handle this
case throughout the driver, with a WARN_ON_ONCE so that we can try
and work out what happened.
Fixes: 0f181d3cf7d98 ("iommu/rockchip: Add runtime PM support")
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
A number of the Rockchip-specific drivers (IOMMU, display controllers)
are now assuming that CONFIG_PM is set, and may completely misbehave
if that's not the case.
Since there is hardly any reason for this configuration option not
to be selected anyway, let's require it (in the same way Tegra already
does).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
A number of the Rockchip-specific drivers (IOMMU, display controllers)
are now assuming that CONFIG_PM is set, and may completely misbehave
if that's not the case.
Since there is hardly any reason for this configuration option not
to be selected anyway, let's require it (in the same way Tegra already
does).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The idle-states binding documentation[1] mentions that the
'entry-method' property is required on 64-bit platforms and must be
set to "psci".
commit a13f18f59d26 ("Documentation: arm: Fix typo in the idle-states
bindings examples") attempted to fix this earlier but clearly more is
needed.
Fix the cpu-capacity.txt documentation that uses the incorrect value so
we don't get copy-paste errors like these. Clarify the language in
idle-states.txt by removing the reference to the psci bindings that
might be causing this confusion.
Finally, fix devicetrees of various boards to reflect current
documentation.
[1] Documentation/devicetree/bindings/arm/idle-states.txt (see
idle-states node)
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This can be dropped with commit 771c035372a036f83353eef46dbb829780330234
("deprecate the '__deprecated' attribute warnings entirely and for good")
now in upstream.
And we got rid of the last __deprecated use, too.
Signed-off-by: Sedat Dilek <sedat.dilek@credativ.de>
[wsa: shortened commit message to reflect the current situation]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Two users have reported [1] that they have an "extremely unlikely" system
with more than MAX_PA/2 memory and L1TF mitigation is not effective.
Make the warning more helpful by suggesting the proper mem=X kernel boot
parameter to make it effective and a link to the L1TF document to help
decide if the mitigation is worth the unusable RAM.
[1] https://bugzilla.suse.com/show_bug.cgi?id=1105536
Suggested-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/966571f0-9d7f-43dc-92c6-a10eec7a1254@suse.cz
|
|
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The old @sunsite.dk address is no longer active, so update the references.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
There aren't any users left. Remove this callback from the 2.4 times.
Phew, finally, that took years to reach...
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
As we now have deferred probing, we can use a custom mechanism and
finally get rid of the legacy interface from the i2c core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
|
Daniel Borkmann
John Fastabend
Stefan Agner
Zhu Yanjun
Linus Walleij
Haiqing Bai
Jiri Pirko
Xin Long
Jens Axboe
Kees Cook
Linus Torvalds
Colin Ian King
Jason Wang
Manish Chopra
Anssi Hannula
Geert Uytterhoeven
Ahmad Fatoum
Ido Schimmel
Jacob Keller
Martyna Szapar
Sebastian Basierski
Tony Nguyen
Jia-Ju Bai
Jesus Sanchez-Palencia
Bo Chen
YueHaibing
Marc Zyngier
Amit Kucheria
Sedat Dilek
Vlastimil Babka
Wolfram Sang
Peter Korsgaard
Wolfram Sang